KD2004-DG10A Printheads Compact high speed thick film thermal printhead (8dots / mm) KD2004-DG10A Using its expertise in LSI technology, ROHM has developed new high density driver chips for use in the KD2004-DG10A . Capable of being employed for both thermal and thermal transfer printing, with a print speed of 250mm/s, the resulting printheads are the fastest in their class. The high-speed and high-density printing answers the needs of ATM, kiosk and ticket printing devices, which are increasingly being called upon to produce graphical output. zApplications Label printers Ticket printers POS printers ATM printers KIOSK printers Terminal printers zFeatures 1) The use of a special partial glaze and the latest heating element structure, along with new high-density driver chips that can accept big current, has allowed ROHM to achieve print speeds of 250mm/s, the fastest in its class. 2) One rank resistance value of 650Ω ± 3% eliminates the inconvenience of rank selection. 3) The required driving voltage of 3.15 to 5.25V allows wide range of power supply voltage setting. This also allows multiple choice of electronic components for printers. 4) 2-inch, 3-inch and 4-inch series are available. zExternal dimensions (Unit : mm) Max.1.7 118 (5.1) Dot #832 Dot #1 4±0.2 Exposed Conductor Side 10.2 5.1±0.1 110±0.2 No.1 Insert Direction Connector M No.28 AX .φ 20 .0 Max.18 2.6±0.1 104 (Effective Print Width) 2-M3 (Effective Depth 3) 1/4 KD2004-DG10A Printheads zEquivalent circuit VH GND 1 ,2 ,3 ,4 2 5 ,2 6 ,2 7 ,2 8 ST B2 ST B1 LAT CLK DI 2 D O2 DI 1 D O1 TM TM DOT #1 7 -1 1 ,1 9 -2 2 VSF VDD DOT #832 L /S 7 6 5 4 3 2 1 15 18 12 14 L A T C H R E G I S TE R 13 24 23 S H IF T R E G I S TE R 2 S H I FT R E G I S T E R 1 6 5 16 T H E R M I S TO R 17 Fig.1 zPin assignments No. Circuit No. Circuit 1 VH 15 VDD 2 VH 16 TM 3 VH 17 TM 4 VH 18 STB2 5 DI1 19 GND 6 DO1 20 GND 7 GND 21 GND 8 GND 22 GND 9 GND 23 DO2 10 GND 24 DI2 11 GND 25 VSF 12 STB1 26 VH 13 CLK 27 VH 14 LAT 28 VH 2/4 KD2004-DG10A Printheads zTiming chart tw CLK CLOCK (CLK) t setup DI t hold DI DATA IN (DI) "High":BLACK "Low" :WHITE td DO DATA OUT (DO) "High":BLACK "Low" :WHITE t setup LAT t hold LAT LATCH (LAT) "High":HOLD "Low" :THROUGH tw LAT t setup STB STROBE (STB) tdo tdo DRIVER OUT Fig.2 zCharacteristics Parameter Symbol Typical Unit Effective printing width − 104 mm Dot pitch − 0.125 mm − 832 dots Rave 650 Ω Total dot number Average resistance value Applied voltage VH 24 V Applied power PO 0.74 W/dot Print cycle SLT 0.5 ms Pulse width TON 0.20 ms Maximum number of dots energized simultaneously − 448 dots Maximum clock frequency − 16 MHz Maximum roller diameter − φ20.0 Running life / pulse life − 50/5×10 km/pulses Operating temperature − 5 to 45 °C mm 7 3/4 KD2004-DG10A Printheads zElectrical characteristic curves 0.8 0.8 1.8 0.6 1.4 0.5 0.4 0.3 0.2 0.1 0 0 1 2 3 4 5 SCANNING LINE TIME (ms/line) SLT : 0.620ms/line 0.7 0.6 ENERGY (mJ/dot) 1.6 OPTICAL DENSITY ENERGY (mJ/dot) Paper : KF50-HDA (OJI) 0.7 1.2 1.0 0.8 0.6 0.4 0.3 0.4 0.2 0.2 0.1 0.0 0.00 0.05 0.10 0.15 0.20 0.25 0.30 ENERGY (mJ/dot) Fig.3 Adaptive speed chart 0.5 Fig.4 Representative density curve 0 0 1 2 3 4 5 SCANNING LINE TIME (ms/line) Fig.5 Maximum energy curve 180 160 RESISTANCE : (kΩ) 140 120 100 80 60 40 20 0 −20 −10 0 10 20 30 40 50 60 70 TEMPERATURE : (°C) Fig.6 Thermistor curve 4/4 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1