KD3002-DC10A Printheads Thick Film Thermal Printhead (300dpi) KD3002-DC10A KD3002-DC10A is developing type of GL40 series which are developed mainly for label printe rs. We have adopted low coefficient of abrasion and conductive protection coat to GL40 series which are possible for high speed and good printing quality. That is KD3002-DC10A which is 24V standard thick film thermal print head with high speed, high quality of printing, high durability, long life, and strong resistance to abration. zApplications High speed label printer Food label printer High speed ticket printer High speed terminal printer zFeatures 1) Perform 150km life time adopting new protective coat. (Perform three times life time by coefficient of abrasion which is about is about 1/10 of current mass-producing coat.) 2) Build in thermal high speeded heater and perform high printing 4 IPS. (100mm / s) 3) Available for thermal transfer printing by adopting specific partial glaze.. zExternal dimensions (Unit : mm) TYPE OF PRINTHEAD (5) (5.396) 54.208(Effetive Print Width) DOT #640 3-M3(Effective Depth 3) 6.1±0.4 65 φ3H10 Length 4 (Effective Depth 3) DOT #1 DOT #640 55.5±0.3 55±0.3 (20.8) 25±0.5 #20 #4 #1 Max.5.5 15.3±0.3 7.3±0.3 Max.10 #2 17.8±0.2 Ma x .φ2 0 (3) Max.36 Max.45 0.896±0.2 28±0.3 56±0.3 φ3H10 (Effective Depth 3) #1 HIROSE HIF3FC-20PA-2.54DS #19 JST B4PS-VH 1/4 KD3002-DC10A Printheads zEquivalent circuit DOT #640 VH DOT #1 VSF L/S #640 #321 #320 #1 GND VDD STB2 STB1 N.C. LATCH REGISTER /LAT CLK SHIFT REGISTER SHIFT REGISTER DI2 DO2 DI1 DO1 TM THERMISTOR 30kΩ B : 3950K TM CONNECTOR VSF : Usually VSF and VH are connected. When measuring R value of Heatelement , VSF and VH should be separated. DI No. DOT No. STB No. DOT No. DI1 1 to 320 STB1 1 to 320 DI2 321 to 640 STB2 321 to 640 Fig. 1 zPin configuration CONNECTOR A CONNECTOR B No. Circuit No. Circuit No. Circuit 1 GND 11 TM 1 VH 2 VSF 12 TM 2 VH 3 GND 13 DI1 3 GND 4 VDD 14 DO1 4 GND 5 STB2 15 N.C. 6 CLK 16 N.C. 7 DI2 17 N.C. 8 DO2 18 N.C. 9 STB1 19 N.C. 10 LAT 20 N.C. 2/4 KD3002-DC10A Printheads zTiming chart Min.30ns CLOCK (CLK) Min.30ns DATA IN (DI) "High" : BLACK "Low" : WHITE Min.10ns Max.120ns DATA OUT (DO) "High" : BLACK "Low" : WHITE Min.200ns Min.50ns LATCH (LAT) "High" : HOLD "Low" : THROUGH Min.100ns Min.300ns STROBE (STB) Max.10µs Max.10µs DRIVER OUT Fig.2 zCharacteristics Symbol Typ. Unit Effective printing width − 54.21 mm Dot pitch − 0.0847 mm Total dot number − 640 dots Rave 1000 Ω VH 24 V Parameter Average resistance value Applied voltage Applied power PO 0.55 W / dot SLT 0.83 ms Maximum number of dots energized simultaneously − 640 dots Maximum clock frequency − 12 MHz Maximum roller diameter − φ20.0 Running life / pulse life − 150 / 1×10 km / pulses Operating temperature − 5 to 45 °C Print cycle mm 8 3/4 KD3002-DC10A Printheads 0.40 1.6 180 0.35 1.4 160 0.30 1.2 0.25 1.0 0.20 0.8 0.15 0.6 0.10 0.4 0.50 0.2 0 0 0 0.5 1 1.5 2 2.5 RESISTANCE : (kΩ) 140 0.6SPEED : 4IPS O.D ENERGY : (mJ / dot) zData sheet 120 100 80 60 40 20 0 0.02 0.04 0.06 0.08 0.1 0.12 0.14 0.16 0.18 0 −20 −10 0 10 20 30 40 50 SLT : (ms / line) ENERGY : (mj / dot) TEMPERATURE : (˚C) Fig.3 Maximum energy curve Fig.4 Representative density curve Fig.5 Thermistor curve 60 70 4/4 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1