www.eicsemi.com ES3A - ES3J SURFACE MOUNT SUPER FAST RECTIFIERS PRV : 50 - 600 Volts Io : 3.0 Amperes SMC (DO-214AB) 8.0 ± 0.15 * * * * * * * * 7.0 ± 0.20 1.1 ± 0.3 FEATURES : Glass passivated junction chip High current capability High surge current capability High reliability Low reverse current Low forward voltage drop Super fast recovery time Pb / RoHS Free 0.1 ± 0.1 0.20± 0.07 3.0 ± 0.2 2.3 ± 0.2 5.8 ± 0.15 MECHANICAL DATA : * * * * * Case : SMC Molded plastic Epoxy : UL94V-O rate flame retardant Lead : Lead Formed for Surface Mount Mounting position : Any Weight : 0.21 gram Dimensions in millimeters MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. RATING SYMBOL ES3A ES3B ES3C ES3D ES3E ES3G ES3J UNIT Maximum Recurrent Peak Reverse Voltage VRRM 50 100 150 200 300 400 600 V Maximum RMS Voltage VRMS 35 70 105 140 210 280 420 V Maximum DC Blocking Voltage Maximum Average Forward Current at TL = 100 °C VDC 50 100 150 200 300 400 600 V IF(AV) 3.0 A IFSM 100 A Maximum Peak Forward Surge Current, 8.3ms Single half sine wave Superimposed on rated load Maximum Peak Forward Voltage at IF = 3.0 A. VF Maximum DC Reverse Current Ta = 25 °C IR 10 at Rated DC Blocking Voltage Ta = 100 °C IR(H) 500 Maximum Reverse Recovery Time ( Note 1 ) Trr 35 Typical Junction Capacitance ( Note 2 ) CJ Junction Temperature Range TJ - 55 to + 150 °C Storage Temperature Range TSTG - 55 to + 150 °C 0.95 1.3 50 1.7 V μA ns 40 pF Notes : ( 1 ) Reverse Recovery Test Conditions : IF = 0.5 A, IR = 1.0 A, Irr = 0.25 A. ( 2 ) Measured at 1.0 MHz and applied reverse voltage of 4.0 VDC Page 1 of 2 Rev. 03: October 8, 2012 www.eicsemi.com RATING AND CHARACTERISTIC CURVES ( ES3A - ES3J ) FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 Ω 10 Ω Trr + 0.5 A 0 D.U.T. + PULSE GENERATOR ( NOTE 2 ) 50 Vdc (approx) 1Ω - 0.25 A OSCILLOSCOPE ( NOTE 1 ) - 1.0 A SET TIME BASE FOR 15 ns/cm NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF. 1 cm 2. Rise time = 10 ns max., Source Impedance = 50 ohms. 3. All Resistors = Non-inductive Types. FIG.3 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 3.0 125 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD OUTPUT CURRENT, AMPERES FIG.2 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT 2.4 1.8 1.2 0.6 Ta = 50 °C 100 8.3 ms SINGLE HALF SINE WAVE 75 50 25 60Hz RESISTIVE OR INDUCTIVE LOAD 0 0 25 50 75 100 125 150 0 175 1 2 4 AMBIENT TEMPERATURE, ( °C) 10 20 40 60 100 NUMBER OF CYCLES AT 60Hz FIG.4 - TYPICAL FORWARD CHARACTERISTICS FIG.5 - TYPICAL REVERSE CHARACTERISTICS 100 1000 REVERSE CURRENT, MICROAMPERES ES3E - ES3G ES3A - ES3D FORWARD CURRENT, AMPERES 6 10 ES3J 1.0 Pulse Width = 300 μs 2% Duty Cycle 0.1 TJ = 25 °C 0.01 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 FORWARD VOLTAGE, VOLTS Page 2 of 2 4.5 5.0 TJ = 100 °C 100 10 1 TJ = 25 °C 0.1 0 20 40 60 80 100 120 140 PERCENT OF RATED REVERSE VOLTAGE, (%) Rev. 03: October 8, 2012