- There’s no sound. Check cable connections. Your instrument should be connected to the input on the right side of the pedal, while the amplifier/sound system should be connected to the output on the left. Check to see if the output level of your instrument is adequately high. Alternatively, the battery may be out of power. VERB`8 - Unintended distortion is heard. In case you connect an instrument with a high gain (such as a synthesizer), It can surpass the maximum input level of +4㏈u resulting in distortion. Please adjust the instrument’s output to an adequate level. This may be caused by the depleted battery. - Problems with an external power. The pedal needs to be used with a power adapter that outputs constant 9V DC and can handle at least 150㎃ of current. The polarity of the power jack is center-negative and the power adapter must be corresponding. Please note that while the power jack is connected, the battery is cut off and not used. - Problems with a battery. When powered with a battery, the unit will function only when a mono connector is plugged into the on the right side of the pedal. Power will drawn from the battery as long as the input jack is engaged, even if you are not playing any music. You can also check the battery to make sure it is not exhausted. - LED blinks. This signals a voltage drop in the battery as it reaches the end of its life. This means that it’s about time to change the battery. http://www.illuston.com Please insert a fresh battery or use an external power source. - None of these works, help me! Please reach out to customer service at . - Input/Output ¼" Phone Jacks - Stereo (2-Channel) Audio Input/Output and Expression/Tap Input - Input Impedance 1MΩ - Output Impedance 600Ω - Signal-Noise Ratio 85㏈A typical working - Frequency Response 20㎐ ~ 20k㎐ - Max Input Level +4㏈u beautiful illustrations on your tone. - A/D & D/A 24-bit / 48k㎐ That’s the reason behind - DSP arithmetic 32-bit processing - Bypass Switching True-Bypass or Buffer-Bypass with Trails Mode (Selectable) - Dimensions Width 124㎜ x Depth 104㎜ x Height 38㎜ - Weight 560g (not including battery) - Output Type 9V DC / 150㎃ / Center Negative - Current Draw 75㎃ - Battery 9V (6LR61/6F22/FC-1) - Battery Life approx. 4 hours (with Alkaline Battery) Complete your own music with Quality components, handy features, sturdy build, and most importantly, beautiful sound. True-Stereo processing Wide dynamic range up to +4㏈u True-Bypass or Buffer-Bypass with Trails Mode Expression/Tap pedal connection 8 types of effect model for the perfection Saving your tone up to 8 presets Copyright © 2014 Altonics, Inc. All rights reserved. - - Save your own settings to presets _1_~_8_ and use them - Decay/reverb time that determines how long the reflections The persist. Turn clockwise to increase the length. external switch or expression/volume The left hand LED indicates the volume of the reverb with pedal. Make sure to turn off the power its brightness. before connecting an external pedal. Adjusts the low range frequency of the reverberation. Depending on the maker of the pedal, ※ When switch is engaged, Turn clockwise to obtain a deeper bass sound. the polarity may be different, so please Tip and Sleeve are in contact. Attenuates the decay speed in the higher frequency range. check beforehand for compatibility. Counter clockwise renders a dark and smooth space, - Switch Pedal : Can be set to while the clockwise direction makes the resonating space feel _PRESET_↓ switch. Every press will brighter and colder. change the current preset _1_~_8_ in decreasing order. Sets the level of the delay and dry sound. At 3 o’clock the volume of the delay is equal to the dry sound (1:1 ratio), instantaneously when jamming. connector can accommodate an Switch Pedal Tip Signal Sleeve Ground Tip Signal Ring Voltage Sleeve Ground - Expression/Volume Pedal : With this, you can adjust a selected parameter, turn further clockwise and the dry sound will be disappeared. one of the 4 control knobs. Please refer to “Choosing an EXP Parameter” . (1) Turn the rotary encoder in the center to choose the effect model of your choice. If you power the unit up while pushing down on the central rotary switch, this (2) Adjust the 4 knobs above to create the perfect sound. will allow you to change (3) Push down on the rotary switch for 2 seconds setting. You can map the expression/volume pedal to one of the 4 control knobs. The unit will cycle through the controls as long and the LED will start to blink. as the rotary switch remains pressed, with the LED _3_ _4_ _5_ _6_ indicating the selection of each of the corresponding knobs. Let go when the desired (4) Turn the rotary encoder to any of the preset position parameter is selected. _1_~_8_ . ※ This is only for when you have an expression/volume pedal to connector. (5) Press the rotary switch again and the current sound will be saved in the selected position. Select the desired effect with the rotary encoder in the center. (6) Use _PRESET_↑ / _PRESET_↓ switch to shuffle through and activate the preset of your choice. - Feel the majestic reflections of a well-designed concert hall. - This is a natural, orderly reverberations you would experience in a studio live room. ※ On pressing _PRESET_↑ / _PRESET_↓ switch, The _PRESET_ LED on the bottom left face will light up - The tidy, polished sound of a studio-grade metal-plate reverb. Swinging brilliantly, the sweep reverb makes your song’s sound - all the sweeter. A gated reverb only kicks in during play, making for a more powerful and dynamic sound profile. to indicate that you are in the preset mode. - Feel the unique charm of a ducking delay that responds to your picking. ※ The preset positions of _1_~_8_ are independent from - Harmonic overtones spread out to emulate the sensation Of marbles sparkling in the light. - A perfect reproduction of soft “twangy” sound you would expect from a vintage amp's tin-can spring reverb unit. the effect models written next to them. That is, you can save any effect model to any preset number that you want. - Turns the effect on and off. When the LED is lit up, the effect is functioning, and when it is off, you are in bypass mode. - _PRESET_ Functions as a preset-up _PRESET_↑ switch. Every press will change the current preset _1_~_8_ in increasing order. The switch on the right lets you select the bypass mode of your choice. - The signal passes as if there was nothing on the way. - Provides a low impedance buffer bypass, allowing for a natural fade out when effect is off.