FLOW`8 - Altonics

- There’s no sound.
Check cable connections. Your instrument should be connected to the input on the
right side of the pedal, while the amplifier/sound system should be connected to the
output on the left. Check to see if the output level of your instrument is adequately
high. Alternatively, the battery may be out of power.
FLOW`8
- Unintended distortion is heard.
In case you connect an instrument with a high gain (such as a synthesizer), It can
surpass the maximum input level of +4㏈u resulting in distortion. Please adjust the
instrument’s output to an adequate level. This may be caused by the depleted battery.
- Problems with an external power. The pedal needs to be used with a power adapter that outputs constant 9V DC and
can handle at least 150㎃ of current. The polarity of the power jack is center-negative
and the power adapter must be corresponding.
Please note that while the power jack is connected, the battery is cut off and not used.
- Problems with a battery.
When powered with a battery, the unit will function only when a mono connector is
plugged into the
on the right side of the pedal.
Power will drawn from the battery as long as the input jack is engaged, even if you are
not playing any music. You can also check the battery to make sure it is not exhausted.
-
LED blinks.
This signals a voltage drop in the battery as it reaches the end of its life.
This means that it’s about time to change the battery.
http://www.illuston.com
Please insert a fresh battery or use an external power source.
- None of these works, help me!
Please reach out to customer service at
.
- Input/Output
¼" Phone Jacks - Stereo (2-Channel) Audio Input/Output and Expression/Tap Input
- Input Impedance
1MΩ
- Output Impedance
600Ω
- Signal-Noise Ratio
85㏈A typical working
- Frequency Response
20㎐ ~ 20k㎐
- Max Input Level
+4㏈u
beautiful illustrations on your tone.
- A/D & D/A
24-bit / 48k㎐
That’s the reason behind
- DSP arithmetic
32-bit processing
- Bypass Switching
True-Bypass or Buffer-Bypass with Trails Mode (Selectable)
- Dimensions
Width 124㎜ x Depth 104㎜ x Height 38㎜
- Weight
560g (not including battery)
- Output Type
9V DC / 150㎃ / Center Negative
- Current Draw
70㎃
- Battery
9V (6LR61/6F22/FC-1)
- Battery Life
approx. 4 hours (with Alkaline Battery)
Complete your own music with
Quality components, handy features, sturdy build,
and most importantly, beautiful sound.
True-Stereo processing
Wide dynamic range up to +4㏈u
True-Bypass or Buffer-Bypass with Trails Mode
Expression/Tap pedal connection
8 types of effect model for the perfection
Saving your tone up to 8 presets
Copyright © 2014 Altonics, Inc. All rights reserved.
Changes the modulation speed/rate.
The
instantaneously when jamming.
Clockwise direction increases the speed.
external switch or expression/volume
(1) Turn the rotary encoder in the center to choose the effect
The LED on the left blinks to indicate the modulation time.
pedal. Make sure to turn off the power
Sets the depth and width of the modulation effect.
before connecting an external pedal.
At 5 o'clock, the effect will show the largest variation.
Depending on the maker of the pedal,
※ When switch is engaged,
Depending on the effect model, this will adjust the intensity
the polarity may be different, so please
Tip and Sleeve are in contact.
of the feedback/emphasis/waveform.
check beforehand for compatibility.
Exceptions that are not affected by this knob are:
- Switch Pedal : Can be set to TAP switch
Save your own settings to presets _1_~_8_ and use them
model of your choice.
-
-
(2) Adjust the 4 knobs above to create the perfect sound.
(3) Push down on the rotary switch for 2 seconds
-
and the LED will start to blink.
(4) Turn the rotary encoder to any of the preset position
_1_~_8_ .
,
(5) Press the rotary switch again and the current sound will be
-
saved in the selected position.
,
Switch Pedal
Tip
Signal
Sleeve
Ground
or _PRESET_↑ switch.
.
Adjusts the balance between the level of the modulation
effect and the original signal. Pointed straight up
Tip
Signal
Ring
Voltage
Sleeve
Ground
Please refer to “Changing Pedal Mode” .
- Expression/Volume Pedal : With this,
at 12 o'clock sets an equal ratio of 1:1.
(6) Use _PRESET_↑ / _PRESET_↓ switch to shuffle through and
connector can accommodate an
you can adjust a selected parameter,
one of the 4 control knobs.
activate the preset of your choice.
Please refer to “Choosing an EXP Parameter” .
※ On pressing _PRESET_↑ / _PRESET_↓ switch,
The _PRESET_ LED on the bottom left face will light up
If you power the unit up while pushing down on the central rotary switch, this
to indicate that you are in the preset mode.
will allow you to change
setting. You can map the expression/volume pedal
to one of the 4 control knobs. The unit will cycle through the controls as long
※ The preset positions of _1_~_8_ are independent from
as the rotary switch remains pressed, with the LED _3_ _4_ _5_ _6_ indicating
the effect models written next to them. That is, you can save
the selection of each of the corresponding knobs. Let go when the desired
any effect model to any preset number that you want.
parameter is selected.
※ This is only for when you have an expression/volume pedal to
Powering on
No.
_PRESET_
with _PRESET_
_1_
_PRESET_↑
pedal engaged
_2_
Select the desired effect with the rotary encoder in the center.
_PRESET_↓
TAP
_PRESET_↑
will let you
-
A chorus effect that brings a warm abundance.
-
A vintage flanger that reminds you of a jet fighter.
-
This effect reproduces the unique and wonderful
sound of a rotating leslie speaker.
modify the pedal mode. The unit will cycle through the above
-
settings. The initial setting is at _2_ . While_PRESET_ pedal stays
-
current mode.
Functions as a preset-up switch.
Every press will change the current
Turns the effect on and off.
-
When the LED is lit up, the effect is functioning,
and when it is off, you are in bypass mode.
Functions as a preset-down switch.
Every press will change the current
Panning between left and right makes its mark
especially when you're playing chords.
-
preset _1_~_8_ in increasing order.
- TAP
A soft and slow filter that will make you feel
the sense of “wah-wah”.
-
- _PRESET_↓
Adds some originality to your jam with
the odd sensation brought on by off-sync phases.
down, the LED will light up among _1_ _2_ to indicate the
- _PRESET_↑
connector.
- _PRESET_
try them all by turning the
-
Every press will change the current preset
Functions as a tap time switch.
_1_~_8_ in increasing order.
knob.
Just the right amount of pitch vibrato will bring
liveliness to your tones.
Functions as a preset-up _PRESET_↑ switch.
preset _1_~_8_ in decreasing order.
From a vintage tube tremolo to a modern FET tremolo,
The switch on the right lets you select the bypass mode of your choice.
The interval between two consecutive
-
The signal passes as if there was nothing on the way.
taps will set the
-
Provides a low impedance buffer bypass.
.