ROHM LTR50UZPD

LTR50
Resistors
High Power Chip Resistors<Wide Terminal type>
LTR50 (5025 size : 1W)
zFeatures
1) Improved welding strength
The structure of longer electrodes provides the wider welding area than the chip resistors with normal electrodes,
and this enhanced the solder welding strength.
2) Increased surge-resistance
This is achieved by Rohm’s original trimming technology plus resistive element patterning.
3) High-power tolerance
Two times of the rated power is guaranteed than the normal-electrode resistors.
4) ROHM resistors are ISO-9001 & ISO/TS16949 certified.
Design and specifications are subject to change without notice. Carefully check the specification sheet before using
or ordering it.
zApplications
Automotive, industrial and power supply.
zRatings
Item
Rated power
Conditions
Specifications
Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70°C.
1W
at 70°C
100
POWER LOAD (%)
80
60
40
20
0
−55
0
70
100
155
AMBIENT TEMPERATURE (°C)
Fig.1
Rated voltage
The voltage rating is calculated by the following equation.
If the value obtained exceeds the limiting element voltage,
the voltage rating is equal to the maximum operating voltage.
E: Rated voltage (V)
E= P×R
P: Rated power (W)
R: Nominal resistance (Ω)
Nominal resistance
See Table 1.
Operating temperature
D(±0.5%) F(±1%) J(±5%)
Limiting element voltage
200V
−55°C to + 155°C
1/4
LTR50
Resistors
Table 1
Resistance range
(Ω)
Resistance tolerance
Resistance temperature coefficient
(ppm/°C)
±100
D (±0.5%)
10 ≤ R ≤ 130k (E24)
F (±1%)
±100
±200
J (±5%)
zBefore using components in circuits where they will be exposed to transients such as pulse loads (short–duration, high– level loads), be certain to evaluate the
component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that
is greater than its rated voltage.
zCharacteristics
Item
Resistance
Variation of resistance
with temperature
Overload
Solderability
Resistance to
soldering heat
Rapid change of
temperature
Guaranteed value
Resistor type
J : ±5%
F : ±1%
D : ±0.5%
See Table.1
± (2.0%+0.1Ω)
A new uniform coating of minimum of
95% of the surface being immersed
and no soldering damage.
± (1.0%+0.05Ω)
No remarkable abnormality on the appearance.
JIS C 5201-1 4.8
Measurement : −55 / +25 / +125°C
JIS C 5201-1 4.13
Rated voltage (current) ×2.5, 2s.
Maximum overload voltage : 200V
JIS C 5201-1 4.17
Rosin·Ethanol (25%WT)
Soldering condition : 235±5°C
Duration of immersion : 2.0±0.5s.
JIS C 5201-1 4.18
Soldering condition : 260±5°C
Duration of immersion : 10±1s.
JIS C 5201-1 4.19
Test temp. : −55°C to +125°C 5cyc
± (3.0%+0.1Ω)
JIS C 5201-1 4.24
40°C, 93%RH
Test time : 1,000h to 1,048h
± (3.0%+0.1Ω)
JIS C 5201-1 4.25.1
Rated voltage (current), 70°C
1.5h : ON − 0.5h : OFF
Test time : 1,000h to 1,048h
± (3.0%+0.1Ω)
JIS C 5201-1 4.25.3
155°C
Test time : 1,000h to 1,048h
± (1.0%+0.05Ω)
JIS C 5201-1 4.29
23±5°C, Immersion cleaning, 5±0.5min.
Solvent : 2-propanol
Endurance at 70°C
Endurance
Resistance to solvent
Static electric
characteristics
JIS C 5201-1 4.5
± (1.0%+0.05Ω)
Damp heat, steady state
Bend strength of
the end face plating
Test conditions (JIS C 5201-1)
± (1.0%+0.05Ω)
Without mechanical damage such as breaks.
± (5.0%+0.05Ω)
JIS C 5201-1 4.33
EIAJ ED-4701/300 Test method 304
Voltage : 3kv
C : 100pF
R : 1.5kΩ
Apply cycle : 1 time
2/4
LTR50
Resistors
zDimensions (Unit : mm)
①
⑥
0.38 ±0.2
②
0.90±0.2
0.55±0.10
③
2.50±0.15
④
2.50±0.15
⑤
No.
Material
1
Resistive element
(Oxide metal thick film)
2
Silver thick film electrode
3
Nickel electrode
4
Sn electrode
5
Alumina substrate
6
Overcoating (Resin)
5.0 ±0.15
zPackaging
Reel
Taping
P0
P2
B0
02
04
06
08
06
D
04
B
02
A
08
W
F
E
0
φD
A0
K
P1
(Unit : mm)
C
Label
W
F
E
A0
B0
12.0±0.3
5.5±0.05
1.75±0.1
3.4±0.2
5.6±0.2
EIAJ ET-7200B compliant
(Unit : mm)
A
B
C
D
D0
P0
P1
P2
K
0
φ180
−1.5
+1
φ60
0
+1.0
13
0
φ13±0.2
φ1.5 +0.1
0
4.0±0.1
4.0±0.1
2.0±0.05
Max. 1.1
3/4
LTR50
Resistors
zPart designation
L T R 5 0
U Z P
J
Resistance tolerance
Part No.
J
F
D
Nominal resistance
±5%
±1%
±0.5%
Resistance code, 3 or 4 digits.
Resistance
tolerance
J
F
D
Resistance
code
:
:
:
3 digits
4 digits
4 digits
Packaging Specifications Code
Part No.
Code
LTR50
UZP
Resistance tolerance
D(±0.5%) F(±1%)
J(±5%)
Packaging specifications
Embossed tape (4mm Pitch)
Reel
φ180mm (7inch)
Basic ordering unit
(pcs)
5,000
Reel (φ180mm) : Compatible with JEITA standard "EIAJ ET-7200B"
: Standard product
4/4
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level
of reliability and the malfunction of which would directly endanger human life (such as medical
instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers
and other safety devices), please be sure to consult with our sales representative in advance.
It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance
of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow
for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in
order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM
cannot be held responsible for any damages arising from the use of the products under conditions out of the
range of the specifications or due to non-compliance with the NOTES specified in this catalog.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact your nearest sales office.
ROHM Customer Support System
www.rohm.com
Copyright © 2007 ROHM CO.,LTD.
THE AMERICAS / EUPOPE / ASIA / JAPAN
Contact us : [email protected] rohm.co. jp
21, Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan
TEL : +81-75-311-2121
FAX : +81-75-315-0172
Appendix1-Rev2.0