For more information, please visit the product page. date 09/16/2013 page 1 of 5 SERIES: VLED15 │ DESCRIPTION: LED DRIVER FEATURES • • • • • • • • constant current high efficiency 90~135 Vac and 176~265 Vac input range available 0.35~1.5 A output current operates with industry standard dimmers compact encapsulated assembly active power factor correction over voltage, over current, over temperature protection max., short circuit protection: auto recovery • high temperature operation (up to 90°C case) • UL approved, ENEC approved, CE Mark • long life > 50,000 hours RoHS MODEL output voltage1 min (Vdc) output wattage efficiency max (Vdc) min (mA) output current max (mA) max (W) max (%) VLED15-120-350 24 48 0 350 16.8 80 VLED15-120-480 10 13.5 0 480 6.5 80 VLED15-120-600 8 12 0 600 7.2 80 VLED15-120-700 16 24 0 700 16.8 80 VLED15-120-800 8 12 0 800 9.6 80 VLED15-120-900 10 16 0 900 14.4 80 VLED15-120-900L 8 12 0 900 10.8 80 VLED15-120-1000 10 16 0 1,000 16 80 VLED15-120-1200 10 14.1 0 1,200 16.92 80 VLED15-120-1250 8 12 0 1,250 15 80 VLED15-120-14002 8 11.5 0 1,400 16.1 80 VLED15-120-1500 5 10 0 1,500 15 80 VLED15-230-350 24 48 0 350 16.8 80 VLED15-230-480 10 13.5 0 480 6.5 80 VLED15-230-600 8 12 0 600 7.2 80 VLED15-230-700 16 24 0 700 16.8 80 VLED15-230-800 8 12 0 800 9.6 80 VLED15-230-900 10 16 0 900 14.4 80 VLED15-230-900L 8 12 0 900 10.8 80 VLED15-230-1000 10 16 0 1,000 16 80 VLED15-230-1200 10 14.1 0 1,200 16.92 80 VLED15-230-1250 8 12 0 1,250 15 80 VLED15-230-14002 8 11.5 0 1,400 16.1 80 VLED15-230-1500 5 10 0 1,500 15 80 Note: 1. Total LED forward voltage must be within these ratings under all conditions including dimming 2. 80°C maximum case rating 3. Ripple Current: <40% (p-p) of maximum Output Current with no dimming cui.com For more information, please visit the product page. CUI Inc │ SERIES: VLED15 │ DESCRIPTION: LED DRIVER date 09/16/2013 │ page 2 of 5 PART NUMBER KEY VLED15 - XXX - XXXX Base Number Input Voltage 120 = 120 Vac 230 = 230 Vac Output Current (in mA) INPUT parameter conditions/description min voltage frequency input current at 115 Vac inrush current at 25°C power factor at 120 Vac max units 90 176 typ 135 265 Vac Vac 47 63 Hz 0.22 A 5 A 90 % OUTPUT parameter conditions/description voltage accuracy of set point min load regulation typ max units ±5 % ±5 % PROTECTION parameter conditions/description over voltage protection auto restart over current protection auto restart short circuit protection auto restart control output dims without any flicker dimming range (conduction angle/output) use with incandescent dimmer over temperature protection auto restart 30 147 degrees max units SAFETY & COMPLIANCE parameter conditions/description min typ isolation meets the UL 60950-1 reinforced, double insulation NEC (Class 2) EN 60598-1 class II safety approvals UL 60950-1, LPS, UL 8750, EN61347-2-13 EMI/EMC EN 55015 class B, FCC class 47 CFR part 15 class B, EN 61000-4-(2,3,4,5,6,11), IEC 61000-3-(2,3) ANSI c62.41-1991 category A1, 2.5 kV Ringwave harmonics meets EN 61000-3-(2,3) leakage current at 120 Vac RoHS compliant yes 0.25 mA max units ENVIRONMENTAL parameter conditions/description min typ operating temperature -30 90 °C storage temperature -40 95 °C 5 95 % 90 °C operating humidity non-condensing surface temperature exposed surfaces, under all operating conditions cui.com For more information, please visit the product page. CUI Inc │ SERIES: VLED15 │ DESCRIPTION: LED DRIVER date 09/16/2013 │ page 3 of 5 MECHANICAL parameter conditions/description dimensions 82 x 56 x 29 (3.21 x 2.21 x 1.13 inch) min typ max mm 145 5.1 weight g oz MECHANICAL DRAWING units: mm tolerance: ±0.3 mm unless otherwise specified 56.22 2.213 SCALE: 1:2 81.62 3.213 152.00 5.984 (2 PLCS) 5.00 9.50 0.374 (2 PLCS) cui.com units For more information, please visit the product page. CUI Inc │ SERIES: VLED15 │ DESCRIPTION: LED DRIVER date 09/16/2013 │ page 4 of 5 DIMMING REQUIREMENTS Dimming of the driver shall be possible with standard triac based incandescent dimmers that chops the AC voltage as shown below or with Electronic Low Voltage dimmers that employ reverse phase control. Chopped AC Input to Driver AC Wall Power During the rapid rise time of the AC voltage when the dimmer turns on, the driver shall not generate any voltage or current oscillations and inrush current shall be controlled. During the on time of the AC input, the driver shall regulate the output. The RMS value of the driver output current shall be proportional to the on time of the AC input voltage. Care must be taken to assure that the minimum load requirements are met. Multiple drivers/LEDs may be connected to the dimmer in order to meet the minimum load requirement. DIMMING RANGE When operating with an incandescent dimmer, the RMS output current shall vary depending upon the conduction angle and RMS value of the applied AC input voltage. The following graph shows the typical output versus conduction angle at various line voltages. Typical Io vs Conducon Angle Output Current (A) Normalized to I Set 1.2 1 100V (200V) 0.8 115V (230V) 132V (264V) 0.6 0.4 0.2 0 0 20 40 60 80 100 120 140 160 VAC Conducon Angle (Degrees) The specified dimming range shall be from 30 degrees through 147 degrees conduction angle. Operation throughout this dimming range shall be monotonic and produce a smooth transition of light output in both directions of the dimming range. At 120 Vac or 240 Vac input, the driver shall achieve full rated output current at less than 147 degree conduction angle. cui.com For more information, please visit the product page. CUI Inc │ SERIES: VLED15 │ DESCRIPTION: LED DRIVER date 09/16/2013 │ page 5 of 5 REVISION HISTORY rev. description date 1.0 initial release 07/29/2010 1.01 model update and added dimensions 03/21/2011 1.02 applied new spec template 02/15/2012 1.03 updated input voltage 04/24/2012 1.04 new template applied 07/18/2012 1.05 corrected output current units 09/16/2013 The revision history provided is for informational purposes only and is believed to be accurate. Headquarters 20050 SW 112th Ave. Tualatin, OR 97062 800.275.4899 Fax 503.612.2383 cui.com [email protected] CUI offers a one (1) year limited warranty. Complete warranty information is listed on our website. CUI reserves the right to make changes to the product at any time without notice. Information provided by CUI is believed to be accurate and reliable. However, no responsibility is assumed by CUI for its use, nor for any infringements of patents or other rights of third parties which may result from its use. CUI products are not authorized or warranted for use as critical components in equipment that requires an extremely high level of reliability. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.