ATM0177B3A T

AZ DISPLAYS
SPECIFICATIONS FOR
LIQUID CRYSTAL DISPLAY
CUSTOMER APPROVAL
※ PART NO. : ATM0177B3A-T (AZ DISPLAYS) VER3.2
COMPANY
CHOP
APPROVAL
CUSTOMER
COMMENTS
AZ DISPLAYS ENGINEERING APPROVAL
DESIGNED BY
CHECKED BY
APPROVED BY
Herbert
LH
GZH
ATM0177B3A-T(AZ DISPLAYS)TFT MODULE VER3.2
REVISION RECORD
REVISION
REVISION DATE
PAGE
CONTENTS
VER1.0
2014-05-14
FIRST ISSUED
VER2.0
2014-07-10
CHANGE TP DIMENSION
CORRECT DRIVING CURRENT
VER3.0
2015-04-22
VER3.1
2015-05-29
14
ADD SOME DIMENSIONS
VER3.2
2015-06-02
14
MODIFY SOME DIMENSIONS
AZ DISPLAYS
CHANGE BACKLIGHT CIRCUIT
1
ATM0177B3A-T(AZ DISPLAYS)TFT MODULE VER3.2
※ CONTENTS
1.
GENERAL SPECIFICATIONS
2.
PIN ASSIGNMENT
3.
OPERATING SPECIFICATIONS
4.
OPTICAL SPECIFICATIONS
5.
RELIABILITY TEST
6.
PRECAUTION FOR USING LCM
7.
MECHANICAL DRAWING
8.
PACKAGE DRAWING
9.
INSPECTION SPECIFICATION
AZ DISPLAYS
2
ATM0177B3A-T(AZ DISPLAYS)TFT MODULE VER3.2
1. GENERAL SPECIFICATIONS
Item
Specification
1. LCD size
1.77 inch(Diagonal)
2. Driver element
a-Si TFT active matrix
3. Resolution
128x(RGB)x160
4. Display mode
Normally white , Transmissive
5. Dot Pitch (W*H)
0.073mm(W) x 0.219mm(H)
6. Pixel pitch(W*H)
0.219mm(W) x 0.219mm(H)
7.
Active Area(W*H)
28.032mm(W) x 35.04mm(H)
8.
Module size (W*H)
34.70mm(W) x 46.7mm(H) x 3.75mm Max(D)
9.
Surface treatment
Clear
10. Color arrangement
Remark
Note 1
RGB-stripe
11. Color
65K
12. Contrller
ILI9163V
13. Interface
4-wire SPI
14. Weight
T.B.D.
15. RoHS
RoHS compliant
Note 1: Please refer to mechanical drawing.
AZ DISPLAYS
3
ATM0177B3A-T(AZ DISPLAYS)TFT MODULE VER3.2
2. PIN ASSIGNMENT
Pin No.
Symbol
Function
Level
1
XR
Right electrode of TP
I/O
2
YD
Bottom electrode of TP
I/O
3
XL
Left electrode of TP
I/O
4
YU
Top electrode of TP
I/O
5
A
Power for LED backlight(Cathode)
P
6
NC
No connection
--
7
NC
No connection
--
8
GND
Power ground
P
9
VCC
Power supply
P
10
SDA
Serial data
I/O
11
SCK
Serial clock
I
12
A0
Data/clock selection
I
13
REST
Reset
I
14
K
Power for LED backlight(Anode)
P
15
CS
Chip selection
I
Note
I: input, O: output, P: Power
AZ DISPLAYS
4
ATM0177B3A-T(AZ DISPLAYS)TFT MODULE VER3.2
3. Operating Specification
3.1 ABSOLUTE MAXIMUM RATINGS
Item
Symbol
Values
Min.
Max.
Unit
Remark
Power Voltage
VCC
-0.3
4.6
V
Operation Temperature
TOP
-20
70
ºC
Storage Temperature
TST
-30
80
ºC
LED Reverse Voltage
VR
-
1.2
V
Each LED
Note 2
LED Forward Current
IF
25
mA
Each LED
Note 1: The absolute maximum rating values of this product are not allowed to be exceeded
at any times. Should a module be used with any of the absolute maximum ratings
exceeded, the characteristics of the module may not be recovered, or in an extreme
case, the module may be permanently destroyed.
Note 2: VR Conditions: Zener Diode 20mA
3.1.1 Typical Operation Conditions
Item
Symbol
Values
Min.
Typ.
Max.
Unit
Power Voltage
VCC
2.6
2.8
3.3
V
Input Logic High Voltage
VIH
0.8VCC
--
VCC
V
Input Logic Low Voltage
VIL
0
--
0.2VCC
V
Remark
3.1.2 Backlight driving conditions
Item
Symbol
Voltage for LED Backlight
Values
Unit
Min.
Typ.
Max.
VL
2.9
3.2
3.3
V
Current for LED Backlight
IL
--
40
--
mA
LED life time
--
30000
--
--
Hr
Remark
Note 1
Note 1: The “LED life time” is defined as the module brightness decrease to 50% original brightness at
Ta=25℃ and IL =40mA.
AZ DISPLAYS
5
ATM0177B3A-T(AZ DISPLAYS)TFT MODULE VER3.2
3.3 Timing Characteristics
AZ DISPLAYS
6
ATM0177B3A-T(AZ DISPLAYS)TFT MODULE VER3.2
AZ DISPLAYS
7
ATM0177B3A-T(AZ DISPLAYS)TFT MODULE VER3.2
4.0 OPTICAL SPECIFICATIONS
Item
Viewing Angle
(CR≥10)
Response Time
Contrast Ratio
Symbol
Condition
θL
Φ=180o(9 O'CLOCK)
θR
Luminance
Luminance Uniformity
Min.
Typ.
Max.
60
70
--
o
60
70
--
o
Φ=0 (3 O'CLOCK)
Unit
Remark
Note 1
degree
θT
Φ=90 (12 O'CLOCK)
20
30
--
θB
Φ=270o(6 O'CLOCK)
35
45
--
TON
--
10
20
msec
Note 3
TOFF
--
15
30
msec
Note 3
CR
400
500
--
--
Note 4
0.26
0.31
0.36
--
Note 2
0.28
0.33
0.38
--
Normal
WX
Color Chromaticity
Values
o
Θ=Φ=0
WY
L
360
--
--
cd/m
YU
75
80
--
%
Note 5
Note 6
2
Note 6
Note 7
Test Conditions:
1. If=40mA, the ambient temperature is 25℃.
2. The test systems refer to Note 2.
Note 1: Definition of viewing angle range
Figure 4.1 Definition of viewing angle.
AZ DISPLAYS
8
ATM0177B3A-T(AZ DISPLAYS)TFT MODULE VER3.2
Note 2: Definition of optical measurement system.
The optical characteristics should be measured in dark room. After 30 minutes operation, the optical properties are
measured at the center point of the LCD screen. (Response time is measured by Photo detector TOPCON
Figure 4.2 Optical measurement system setup
Note 3: Definition of Response time
The response time is defined as the LCD optical switching time interval between “White” state and “Black” state. Rise
time (TON) is the time between photo detector output intensity changed from 90% to 10%. And fall time (TOFF) is the
time between photo detector output intensity changed from 10% to 90%.
Figure 4.3 Definition of response.
AZ DISPLAYS
9
ATM0177B3A-T(AZ DISPLAYS)TFT MODULE VER3.2
Note 4: Definition of contrast ratio
Note 5: Definition of color chromaticity (CIE1931)
Color coordinates measured at center point of LCD.
Note 6: All input terminals LCD panel must be ground while measuring the center area of the panel.
Note 7: Definition of Luminance Uniformity
Active area is divided into 9 measuring areas (Refer to Fig. 4-4 ).Every measuring point is placed at the center of each
measuring area.
Figure 4.3 Definition of measuring points.
Bmax: The measured maximum luminance of all measurement position.
Bmin: The measured minimum luminance of all measurement position.
AZ DISPLAYS
10
ATM0177B3A-T(AZ DISPLAYS)TFT MODULE VER3.2
5. RELIABILITY TEST
Item
High temperature
storage
Low temperature
storage
High temperature
operation
Low temperature
operation
High temperature/High
humidity operation
Thermal Shock
Package drop test
Test Condition Item
Ta= 70 ºC 240hrs
Ta=-20 ºC 240hrs
Ts= 60 ºC 240hrs
Ts=-10 ºC 240hrs
Remark
Note 1
Note 4
Note 1
Note 4
Note 2
Note 4
Note 1
Note 4
90% RH 40ºC 120hrs
Note 4
-1℃/30 min ~ +6℃/30 min for a total 10
cycles, Start with cold temperature and end
with high temperature.
Note 4
Height:100 cm
1 corner, 3 edges, 6 surfaces
Note 1: Ta is the ambient temperature of samples.
Note 2: Ts is the temperature of panel’s surface.
Note 3: In the standard condition, there shall be no practical problem that may affect the
display function. After the reliability test, the product only guarantees operation,
but don’t guarantee all of the cosmetic specification.
Note 4: Before cosmetic and function test, the product must have enough recovery time, at least 2 hours
at room temperature.
AZ DISPLAYS
11
ATM0177B3A-T(AZ DISPLAYS)TFT MODULE VER3.2
6. PRECAUTION FOR USING LCM
1. When design the product with this LCD Module, make sure the viewing angle matches to its purpose of usage.
2. As LCD panel is made of glass substrate, Dropping the LCD module or banging it against hard objects may cause
cracking or fragmentation. Especially at corners and edges.
3. Although the polarizer of this LCD Module has the anti-glare coating, always be careful not to scratch its surface.
Use of a plastic cover is recommended to protect the surface of polarizer.
4. If the LCD module is stored at below specified temperature, the LC material may freeze and be deteriorated. If it is
stored at above specified temperature, the molecular orientation of the LC material may change to Liquid state and it
may not revert to its original state. Excessive temperature and humidity could cause polarizer peel off or bubble.
Therefore, the LCD module should always be stored within specified temperature range.
5. Saliva or water droplets must be wiped off immediately as those may leave stains or cause color changes if
remained for a long time. Water vapor will cause corrosion of ITO electrodes.
6. If the surface of LCD panel needs to be cleaned, wipe it swiftly with cotton or other soft cloth. If it is not still clean
enough, blow a breath on the surface and wipe again.
7. The module should be driven according to the specified ratings to avoid malfunction and permanent damage.
Applying DC voltage cause a rapid deterioration of LC material. Make sure to apply alternating waveform by
continuous application of the M signal. Especially the power ON/OFF sequence should be kept to avoid latch-up of
driver LSIs and DC charge up to LCD panel.
8. Mechanical Considerations
a) LCM are assembled and adjusted with a high degree of precision. Avoid excessive shocks and do not make
any alterations or modifications. The following should be noted.
b) Do not tamper in any way with the tabs on the metal frame.
c) Do not modify the PCB by drilling extra holes, changing its outline, moving its components or modifying its
pattern.
9. Static Electricity
a) Operator
Wear the electrostatics shielded clothes because human body may be statically charged if not ware shielded clothes.
Never touch any of the conductive parts such as the LSI pads; the copper leads on the PCB and the interface terminals
with any parts of the human body.
b) Equipment
There is a possibility that the static electricity is charged to the equipment, which has a function of peeling or friction
action (ex: conveyer, soldering iron, working table). Earth the equipment through proper resistance (electrostatic earth:
1x108 ohm).
Only properly grounded soldering irons should be used.
If an electric screwdriver is used, it should be well grounded and shielded from commutator sparks.
The normal static prevention measures should be observed for work clothes and working benches; for the latter
conductive (rubber) mat is recommended.
c) Floor
Floor is the important part to drain static electricity, which is generated by operators or equipment.
There is a possibility that charged static electricity is not properly drained in case of insulating floor. Set the electrostatic
earth (electrostatic earth: 1x108 ohm).
d) Humidity
Proper humidity helps in reducing the chance of generating electrostatic charges. Humidity should be kept over 50%RH.
e) Transportation/storage
The storage materials also need to be anti-static treated because there is a possibility that the human body or storage
materials such as containers may be statically charged by friction or peeling.
The modules should be kept in antistatic bags or other containers resistant to static for storage.
f) Soldering
Soldering anything to this TFT display would void the warranty.
g) Others
The laminator (protective film) is attached on the surface of LCD panel to prevent it from scratches or stains. It should be
peeled off slowly using static eliminator.
Static eliminator should also be installed to the workbench to prevent LCD module from static charge.
10. Operation
a) Driving voltage should be kept within specified range; excess voltage shortens display life.
b) Response time increases with decrease in temperature.
c) Display may turn black or dark blue at temperatures above its operational range; this is (however not pressing
on the viewing area) may cause the segments to appear “fractured”.
d) Mechanical disturbance during operation (such as pressing on the viewing area) may cause the segments to
appear “fractured”.
AZ DISPLAYS
12
ATM0177B3A-T(AZ DISPLAYS)TFT MODULE VER3.2
11. If any fluid leaks out of a damaged glass cell, wash off any human part that comes into contact with soap and water.
The toxicity is extremely low but caution should be exercised at all the time.
12. Disassembling the LCD module can cause permanent damage and it should be strictly avoided.
13. LCD retains the display pattern when it is applied for long time (Image retention). To prevent image retention, do not
apply the fixed pattern for a long time. Image retention is not a deterioration of LCD. It will be removed after display
pattern is changed.
14. Do not use any materials, which emit gas from epoxy resin (hardener for amine) and silicone adhesive agent
(dealcohol or deoxym) to prevent discoloration of polarizer due to gas.
15. Avoid the exposure of the module to the direct sunlight or strong ultraviolet light for a long time.
AZ DISPLAYS
13
ATM0177B3A-T(AZ DISPLAYS)TFT MODULE VER3.2
1.0MAX
+
0.50
0.30
*P0.5*(15-1)=7.00
Print
YU XL YD XR
30100001770005
-
21.5±0.5
LED CIRCUIT DIAGRAM
7. MECHANICAL DRAWING
XR
0.15
2.13
2.73
3.33
*0.3±0.1
*3.50
*35.04(
AA)
36.24 TP AA
37.44 TP VA
46.40TP OUTLINE
*46.70 ±0.3 BL
YU XL YD XR
*8.00±0.1
M
C
L
AZ DISPLAYS
5.20
3.50
*12.60
印白油线
4
8
.
0
2
3.32
2.44
1.84
0.15
*13.86
YD
XL
YU
M
C
L
A
*34.70 ±0.3 BL
34.40 TP OUTLINE
30.44 TP VA
29.23 TP AA
*28.04(
AA)
5
3
.
7
1
13.86
21.53
*23.73±0.5
14
ATM0177B3A-T(AZ DISPLAYS)TFT MODULE VER3.2
8. PACKAGE DRAWING
T.B.D.
9. INSPECTION SPECIFICATION
T.B.D.
AZ DISPLAYS
15