KSM U

AUK CORP.
OPTIC RECEIVER MODULES
KSM-□□□ U Series
Description
KSM-□□□ U Series consist of a PIN Photodiode of high
speed and a preamplifier IC in the package as an receiver
for Infrared remote control systems
Features
Wide supply-voltage range : 2.7V to 5.5V
Shielded against electrical field disturbance
High immunity against ambient light disturbances
Available for carrier frequencies between 32.7kHz to 40kHz
TTL and CMOS compatible
Applications
Short Burst Compatible, Middle Speed
Wide supply-voltage range : 2.7V to 5.5V
Shielded against electrical field disturbance
Basicl immunity against ambient light
Available for carrier frequencies between 32.7kHz to 40kHz
TTL and CMOS compatible
Absolute Maximum Ratings
Parameter
Supply Voltage
Operating Temperature
Storage Temperature
Soldering Temperature
Symbol
Vcc
Topr
Tstg
Tsol
B.P.F Center Frequency
Ratings
6.0
-20℃∼80℃
-25℃∼85℃
260
(Max 5 sec)
[Ta=25℃]
Unit
V
℃
℃
℃
Model No.
KSM-□□1□U seires
KSM-□□2□U seires
KSM-□□3□U seires
KSM-□□4□U seires
KSM-□□5□U seires
B.P.F Center Frequency(㎑)
40.0
36.7
37.9
32.7
Not Support
The contents of this data sheet are subject to change without advance notice for the purpose of improvement.
When using this product, would you please refer to the latest specifications.
Rev. date:
25-Jan-11
KSM-20110125-000
KSM-□□□ U Series
Electrical Characteristics
Parameter
[Ta=25℃, Vcc=5.0V(Vcc=3.0V)]
Symbol
Recommended Supply Voltage
Condition
Vcc
Current Consumption
Max.
Unit
2.7
-
5.5
V
-
1.0(0.8)
2.0
㎃
-
940
-
㎚
B.P.F Center Frequency
fo
-
B.P.F Center
-
㎑
Transmission Distance
(KSM-60□) *1
L
250±50lx
0˚
24
-
-
±30 ˚
20
-
-
*1
VOH
30cm over
Vcc-0.5
Vcc-0.3
-
V
Low level Output voltage
*1
High level Output Pulse Width *1
Low level Output Pulse Width *1
Output Form
VOL
TWH
TWL
the ray axis
Burst wave=600㎲
Period = 1.2㎳
0.2
-
0.5
800
800
V
㎲
㎲
High level Output voltage
*1
No signal input
Typ.
λp
Peak Wavelength
Icc
Min.
400
400
Active Low Output
m
*1. It specifies the maxmum distance between emitter and detector that the output wave form satisfies the standard under the conditions
below against the standard transmitter.
1) Measuring place
: Indoor without extreme reflection of light
2) Ambient light source
: Detecting surface illumination shall be irradiate 200±50lx under ordinary white fluorescence lamp without
high frequency lightning
3) Standard transmitter
: Burst wave of standard transmitter shall be arranged to 400mVP-P under the measuring circuit
The contents of this data sheet are subject to change without advance notice for the purpose of improvement.
When using this product, would you please refer to the latest specifications.
Rev. date:
25-Jan-11
KSM-20110125-000
KSM-□□□ U Series
■ Measuring Method [Ta=25℃]
Output Pulse Width
Standard Transmitter
Test Method of Transmission Distance
t
u
p
t
u
o
r
e
t
t
i
m
s
n
a
r
T
d
r
a
d
n
a
t
S
r
e
t
t
i
m
s
n
a
T
s
u
0
0
6
s
u
0
0
6
%
0
5
y
t
u
D
t
u
o
V
)
o
f
(
y
c
n
e
u
q
e
r
F
r
e
i
r
r
a
C
+5V
10㏀
C
S
O
c
c
V
r
e
t
t
i
m
s
n
a
r
T
e
s
l
u
p
t
u
p
t
u
o
n
o
c
o
m
e
R
Vout
d
n
a
L
m
C
5
2
TH
L
W
T
l
as
tn
no
oi
t
D z
c
N i
e
G r
or
i
hd
s
el
ta
ac
ci
it
dr
ne
Iv
:
10㏀
L
:
e
c
n
a
t
s
i
D
l
a
v
i
r
r
A
10㎌
VH
VL
■ Block Diagram
■ Standard Application Circuit with R-C Decoupling Filter
Rs
Transmitter
Receiver
Module
Vcc
Vcc
Cp1
Vout
Rp
micom
Cp2
GND
GND
*1 Recommended Circuit Description
1) Transmitter(IRED) drive current
: IFP = 300mAP-P ~ 600mAP-P
2) R-C Decoupling Filter with Lower Cut-off Frequency
: R=100Ω~470Ω , C=47uF ~ 100uF
⇒ fc = 1/2πRC = 33.9~3.4Hz
3) optional
: External pull-up resistor =10kΩ over , But recommand null
: Cp2 recommand null
The contents of this data sheet are subject to change without advance notice for the purpose of improvement.
When using this product, would you please refer to the latest specifications.
Rev. date:
25-Jan-11
KSM-20110125-000