VISHAY I N T E R T E C H N O L O G Y , I N C . INTERACTIVE data book rEsIStor ARRays and Networks vishay DALE vsD-db0011-0410 Notes: 1. To navigate: a) Click on the Vishay logo on any datasheet to go to the Contents page for that section. Click on the Vishay logo on any Contents page to go to the main Table of Contents page. b) Click on the products within the Table of Contents to go directly to the datasheet. c) Use the scroll or page up/page down functions. d) Use the Adobe ® Acrobat ® page function in the browser bar. 2. To search the text of the catalog use the Adobe ® Acrobat ® search function. One of the World’s Largest Manufacturers of Discrete Semiconductors and Passive Components RESISTOR ARRAYS AND NETWORKS Resistor Arrays Surface Mount Networks Through-Hole Resistor Networks Military Resistor Networks Customized Resistor Networks w w w. v i s h a y. c o m DATA BOOK V I S H A Y I N T E R T E C H N O L O G Y, I N C . VISHAY INTERTECHNOLOGY, INC. DISCRETE SEMICONDUCTORS RECTIFIERS SMALL-SIGNAL DIODES ZENER & SUPPRESSOR DIODES MOSFETs RF TRANSISTORS OPTOELECTRONICS ICs PASSIVE COMPONENTS CAPACITORS RESISTIVE PRODUCTS MAGNETICS INTEGRATED MODULES DC/DC CONVERTERS STRAIN SENSORS AND TRANSDUCERS STRAIN GAGES AND INSTRUMENTS Schottky (single, dual) Standard, Fast and Ultra-Fast Recovery (single, dual) Clamper/Damper Bridge Superectifier ® Sinterglass Avalanche Diodes Schottky and Switching (single, dual) Tuner/Capacitance (single, dual) Bandswitching PIN Zener Diodes (single, dual) TVS (TransZorb,® Automotive, ESD, Arrays) Power MOSFETs JFETs Bipolar Transistors (AF and RF) Dual Gate MOSFETs MOSMICs® IR Emitters, Detectors and IR Receiver Modules Opto Couplers and Solid State Relays Optical Sensors LEDs and 7 Segment Displays Infrared Data Transceiver Modules Custom products Power ICs Analog Switches Tantalum Capacitors Solid Tantalum Capacitors Wet Tantalum Capacitors Ceramic Capacitors Multilayer Chip Capacitors Disc Capacitors Film Capacitors Power Capacitors Heavy Current Capacitors Aluminum Capacitors Silicon Capacitors Foil Resistors Film Resistors Thin Film Resistors Thick Film Resistors Metal Oxide Film Resistors Carbon Film Resistors Wirewound Resistors Variable Resistors Cermet Variable Resistors Wirewound Variable Resistors Conductive Plastic Variable Resistors Networks/Arrays Non-Linear Resistors NTC Thermistors PTC Thermistors Varistors Inductors Transformers PHOTOSTRESS® INSTRUMENTS TRANSDUCERS Load Cells Weighing Systems ONE OF THE WORLD’S LARGEST MANUFACTURERS OF DISCRETE SEMICONDUCTORS AND PASSIVE COMPONENTS Arrays and Networks Vishay Dale Electronics, Inc. 1122 23rd Street Columbus, NE 68601 U.S.A. Phone: +1 402 564 3131 Fax: +1 402 563 6296 www.vishay.com NOTICE The information in this catalog has been carefully checked for accuracy, and though it is believed to be correct, no warranty, either express or implied, is made as to either its applicability to, or its compatibility with, specific requirements; nor does Vishay Intertechnology, Inc. and its affiliates assume any responsibility for correctness of this information, nor for damages consequent to its use. All such printed materials are not legally binding unless confirmed in writing pursuant to §§463 and 480 11 of the German Code of Civil Law. Warning Regarding Life Support Applications Not all products listed in this catalog are generally recommended for use in life support systems where a failure or malfunction of the component may directly threaten life or cause injury. The user of products in such applications assumes all risks of such use and will agree to hold Vishay Intertechnology, Inc. and all the companies whose products are represented in this catalog, harmless against all damages. Table of Contents Vishay RESISTOR ARRAYS AND NETWORKS Table of Contents ......................................................................................................................................................... 1 Alphabetical Product Listing ......................................................................................................................................................... 2 RESISTOR ARRAYS Standard (Thick Film) CRA04S CRA06E & S CRA06P CRA12E & S Standard (Thin Film) ACAC 0612 ACAC 0612 TRA06E Resistor/Capacitor CRCA Attenuator CZA Thick Film Standard ......................................................................................................................... 4 Thick Film Standard ......................................................................................................................... 6 Thick Film Standard ......................................................................................................................... 8 Thick Film Standard ....................................................................................................................... 10 Professional Thin Film Array ......................................................................................................... 12 Precision Thin Film Array .............................................................................................................. 18 Thin Film Precision ........................................................................................................................ 24 Thick Film Resistor / Capacitor Array ........................................................................................... 26 Surface Mount Chip Attenuator ..................................................................................................... 28 INDUSTRIAL SMD RESISTOR NETWORKS Dual-In-Line SOGC-01, -03, -05 Thick Film Resistor Network, Dual-in-line, Small Outline, Molded DIP ........................................ 32 SOGC-45, -46 Thick Film Resistor Network, Dual-in-line, Small Outline, Molded DIP ........................................ 36 SOMC Thick Film Resistor Network, Dual-in-line, Small Outline, Molded DIP ........................................ 38 Flatpack DFP Thick Film Resistor Network, Flat pack ......................................................................................... 40 INDUSTRIAL THROUGH-HOLE RESISTOR NETWORKS Dual-In-Line MDP 01, 03, 05 Thick Film Resistor Network, Dual-in-line, Molded DIP ................................................................ 44 MDP 45, 46 Thick Film Resistor Network, Dual-in-line, Molded DIP ................................................................ 48 Single-In-Line CSC Thick Film Resistor Network, Single-in-line, Coated SIP ............................................................. 50 MSP Thick Film Resistor Network, Single-in-line, Molded SIP ............................................................. 54 Resistor/Capacitor CS201 Capacitor Networks, Single-in-line, Coated SIP, "D" profile ......................................................... 58 CS206 Resistor/Capacitor Networks, Single-in-line, Coated SIP, ECL Terminators and Line Terminator ....... 60 MDRC Resistor/Capacitor Networks. Dual-in-line, Molded DIP .................................................................... 62 MILITARY QUALIFIED RESISTOR NETWORKS Flatpack DFM Flatpack, MIL-PRF-83401, Type RZ ............................................................................................. 68 Dual-In-Line MDM 14, 16 Dual-in-line, Molded Package, MIL-PRF-83401, Type RZ ........................................................... 72 Single-In-Line MSM Single-in-line, Molded Package, MIL-PRF-83401, Type RZ ........................................................ 76 CUSTOM RESISTOR NETWORKS Product Design Capabilities Multicomps, Custom Networks and Screened Substrates ........................................................... 82 RELATED DOCUMENTS Packaging ....................................................................................................................................................... 84 MIL Identification and Ordering Examples ........................................................................................................................................ 84 Document Number: 31533 Revision 20-Sep-04 www.vishay.com 1 Alphabetical Product Listing Vishay RESISTOR ARRAYS AND NETWORKS ACAC 0612 Professional Thin Film Array ......................................................................................................... 12 ACAC 0612 Precision Thin Film Array .............................................................................................................. 18 CRA04S Thick Film Standard ......................................................................................................................... 4 CRA06E & S Thick Film Standard ......................................................................................................................... 6 CRA06P Thick Film Standard ......................................................................................................................... 8 CRA12E & S Thick Film Standard ....................................................................................................................... 10 CRCA Thick Film Resistor / Capacitor Array ........................................................................................... 26 CS201 Capacitor Networks, Single-in-line, Coated SIP, "D" profile ......................................................... 58 CS206 Resistor/Capacitor Networks, Single-in-line, Coated SIP, ECL Terminators and Line Terminator ....... 60 CSC Thick Film Resistor Network, Single-in-line, Coated SIP ............................................................. 50 CZA Surface Mount Chip Attenuator ..................................................................................................... 28 DFM Flatpack, MIL-PRF-83401, Type RZ ............................................................................................. 68 DFP Thick Film Resistor Network, Flat pack ......................................................................................... 40 MDM 14, 16 Dual-in-line, Molded Package, MIL-PRF-83401, Type RZ ........................................................... 72 MDP 01, 03, 05 Thick Film Resistor Network, Dual-in-line, Molded DIP ................................................................ 44 MDP 45, 46 Thick Film Resistor Network, Dual-in-line, Molded DIP ................................................................ 48 MDRC Resistor/Capacitor Networks. Dual-in-line, Molded DIP .................................................................... 62 MIL Identification and Ordering Examples.........................................................................................84 MSM Single-in-line, Molded Package, MIL-PRF-83401, Type RZ ........................................................ 76 MSP Thick Film Resistor Network, Single-in-line, Molded SIP ............................................................. 54 Packaging ................................................................................................................................................... 84 Product Design Capabilities Multicomps, Custom Networks and Screened Substrates ........................................................... 82 SOGC-01, -03, -05 Thick Film Resistor Network, Dual-in-line, Small Outline, Molded DIP ........................................ 32 SOGC-45, -46 Thick Film Resistor Network, Dual-in-line, Small Outline, Molded DIP ........................................ 36 SOMC Thick Film Resistor Network, Dual-in-line, Small Outline, Molded DIP ........................................ 38 TRA06E Thin Film Precision ........................................................................................................................ 24 www.vishay.com 2 Document Number:31533 Revision 16-Sep-04 Resistor Arrays Resistor or Resistor/Capacitor Configurations • Several Devices in one Package • Commoned, Isolated and Line Terminator Schematics • Design Flexibility • High Packaging Density Model Numbers CRA04S ...............4 CRA06E & S .........6 CRA06P ...............8 CRA12E & S .......10 ACAC0612 (Professional) .....12 ACAC0612 (Precision) ..........18 TRA06E ..............24 CRCA ............ ... 26 CZA ....................28 CRA04S Vishay Dale Thick Film, Resistor Array FEATURES • Convex terminal array with square corners • 4 or 8 terminal package with isolated resistors • Single component reduces board space and component counts • Automatic placement capability • Wave and solder paste reflow compatible • Thick film resistance element • Solderable wrap around termination • Nickel barrier for inner electrode protection • Standard E-24 resistance values • Operating temperature range of - 55°C to + 150°C • Consult factory for additional schematics, values, etc STANDARD ELECTRICAL SPECIFICATIONS MODEL POWER RATING CIRCUIT P70°C W CRA04S 0.063 LIMITING ELEMENT VOLTAGE MAX. V쓖 03 50 TEMPERATURE TOLERANCE COEFFICIENT ppm/°C % RESISTANCE RANGE E-SERIES Ω 200 5 1R0 – 1M0 24 100 2 10R – 1M0 24 Jumper: Zero-Ohm-Resistor on request • • • • Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material Ask about extended value ranges. Packaging: according to EIA 481 Contact factory for tighter tolerance. TECHNICAL SPECIFICATIONS PARAMETER UNIT CRA04S W 0.063 V쓖 50 Vdc/ac peak 100 Category Temperature Range °C - 55 / + 150 Insulation Resistance Ω Rated Dissipation at 70°C Limiting Element Voltage 1) Insulation Voltage (1min) 1) Rated voltage: > 10 9 PxR ORDERING INFORMATION CRA04S 08 03 473 J RT7 MODEL TERMINAL COUNT CIRCUIT TYPE RESISTANCE VALUE Ω TOLERANCE ±% PACKAGING 04, 08 03 only www.vishay.com 4 First two digits (three for 1%) J = ± 5% are significant. Last digit is the G = ± 2% multipier Z = 0Ω Jumper For Technical Questions, contact: [email protected] Paper tape 10000pcs Document Number 31043 Revision 03-Sep-03 CRA04S Vishay Dale Thick Film, Resistor Array 8-Terminal device S – Version SOLDER PAD DIMENSIONS [in millimeters] WAVE c w p a b e 0.45 1.0 0.5 0.4 0.5 0.3 P dimension for the 4 pin is 0.65 The dimensions shown are for a 8 pin part. For parts with different pin numbers use the same pitch and add or substract pads as required. e a e PIN DIMENSIONS [in millimeters] L A A1 B B* PNOM T W 4 1.0 ± 0.1 - 0.33 0.15 0.25 0.65 0.35 1.0 8 2.0 ± 0.2 0.30 0.4 0.15 0.25 0.50 0.35 1.0 ± 0.15 ± 0.15 ± 0.10 ± 0.1 ± 0.1 ± 0.15 TOL Rated Power In % NO# CIRCUIT SCHEMATICS 03 Circuit CRA04S 120 100 80 60 40 20 0 - 55 4 pin 8 pin -25 0 25 Derating 50 75 100 125 150 175 70 Ambient Temperature in °C PERFORMANCE TEST CONDITIONS OF TEST Endurance Test at 70°C per EIA 575-3.14 1000 hours at 70°C, 1.5 hours "ON", 0.5 hours "OFF" ± 1.5% Overload per EIA 575-3.6 Short time overload ± 0.5% Thermal Shock per EIA 575-3.5 ± 0.5% Moisture Resistance per EIA 575-3.10 ± 1.0% Resistance to Soldering Heat EIA 575 3.8 10 seconds at 260°C solder bath temperature ± 2.0% High Temperature Exposure per EIA 575-3.7 ± 1.0% Low Temperature Operations per EIA 575-3.6 ± 0.5% Solderability & Leaching EIA 575-3.12 Document Number 31043 Revision 03-Sep-03 For Technical Questions, contact: [email protected] TEST RESULTS 95% Coverage www.vishay.com 5 CRA06E and S Vishay Dale Thick Film, Resistor Array FEATURES • Convex terminal array available with either scalloped corners (E version) or square corners (S version) • 4, 8, or 10 terminal package with either isolated resistors or bussed resistors • Single component reduces board space and component counts • Automatic placement capability • Wave and solder paste reflow compatible • Thick film resistance element • Solderable wrap around termination • Nickel barrier for inner electrode protection • Standard E-24 (± 2% and ± 5%) and E-96 (± 1%) resistance values • Operating temperature range of - 55°C to + 150°C • Consult factory for additional schematics, values, etc STANDARD ELECTRICAL SPECIFICATIONS MODEL POWER RATING CIRCUIT P70°C W 0.063 02, 20 0.063 03 CRA06S CRA06E & S • • • • LIMITING ELEMENT VOLTAGE MAX. V쓖 50 50 TEMPERATURE TOLERANCE COEFFICIENT ppm/°C % 250 5 100 1 200 2, 5 Jumper: Zero-Ohm-Resistor on Request RESISTANCE RANGE E-SERIES Ω 22R-1M0 10R-1M0 10R-1M0 24 24-96 24 Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material Operating temperature Range: - 55°C to + 150°C Ask about further value ranges Packaging: according to EIA 481 TECHNICAL SPECIFICATIONS PARAMETER UNIT CRA06S CRA06E & S 02, 20 CIRCUIT 03 CIRCUIT W 0.063 0.063 V쓖 50 50 Vdc/ac peak 100 100 °C - 55 / + 150 - 55 / + 150 Rated Dissipation at 70°C Limiting Element Voltage 1) Insulation Voltage (1min) Category Temperature Range Insulation Resistance 1) Rated voltage: > 10 Ω 10 > 10 10 PxR ORDERING INFORMATION CRA06S 08 03 473 J RT1 MODEL TERMINAL COUNT CIRCUIT TYPE R-VALUE Ω TOLERANCE ±% PACKAGING CRA06S CRA06S CRA06E 04, 08 10 08 03 02, 20 03 First two digits (three for 1%) are significant. Last digit is the multiplier 473 = 47K 4702 = 47K 100 = 10Ω 10R0 = 10Ω 000 = 0Ω Jumper F = ± 1% G = ± 2% J = ± 5% Z = 0Ω Jumper Papertape 5000pcs www.vishay.com 6 For Technical Questions, contact: [email protected] Document Number 31002 Revision 09-Jun-04 CRA06E and S Vishay Dale Thick Film, Resistor Array 8-Terminal device S - Version E - Version 1 103 PIN 1 103 A d a a MODEL PIN CRA NO# L 06S 4 1.6 06E 8 3.2 06S 8 3.2 06S 10 3.2 Tol ± 0.15 A 0.38 0.38 0.38 0.34 ± 0.15 e DIMENSIONS [in millimeters] A1 B B* P T W 0.61 0.3 0.3 0.8 0.4 1.5 0.3 0.3 0.8 0.4 1.5 0.61 0.3 0.3 0.8 0.4 1.5 0.49 0.3 0.2 0.64 0.5 1.6 ± 0.15 ± 0.15 ± 0.15 ± 0.1 ± 0.05 ± 0.15 CIRCUIT SCHEMATIC 03 CIRCUIT SOLDER PAD DIMENSIONS [in millimeters] MODEL PINS c w d CRA06S 4 0.8 3.1 0.36 02 CIRCUIT p a b e 0.44 1.15 CRA06E + S 8 0.8 3.1 0.36 0.8 0.44 1.15 0.63 CRA06S 10 0.8 3.1 0.30 0.64 0.34 1.15 0.45 Rated Power % e 120 100 80 60 pin # 1 20 CIRCUIT 40 20 8 pin 4 pin (CRA06S only) 0 - 55 -25 0 25 50 Derating pin # 1 75 70 100 125 150 175 Ambient Temperature °C PERFORMANCE TEST CONDITIONS OF TEST Endurance Test at 70°C per EIA 575 1000 hour at 70°C, 1.5 hours "ON", 0.5 hours "OFF" ±1.0% Overload per EIA 575 Short time overload 2.5 x rated continuous working voltage for 5 seconds. Not to exceed 2 x max operating voltage ± 0.5% Thermal Shock per EIA 575-3.5 ± 0.5% Moisture Resistance per EIA 575-3.10 ± 1.0% Resistance to Soldering Heat EIA 575 10 seconds at 260°C solder bath temperature ± 2.0% High Temperature Exposure per EIA 575-3.7 ± 1.0% Low Temperature Operations per EIA-575-3.6 ± 0.5% Solderability & Leaching EIA 575-3.12 Document Number 31002 Revision 09-Jun-04 For Technical Questions, contact: [email protected] TEST RESULTS 95% Coverage www.vishay.com 7 CRA06P Vishay Dale Thick Film Resistor Array FEATURES • Concave terminal array with square corners • 8 terminal package with isolated resistors • Single component reduces board space and component counts • Automatic placement capability • Wave and solder paste reflow compatible • Thick film resistance element • Solderable wrap around termination • Nickel barrier for inner electrode protection • Standard E-24 (± 2% and 5%) and E-96 (± 1%) resistance values • Operating temperature range of -55°C to +150°C • Consult factory for additional schematics, values, etc STANDARD ELECTRICAL SPECIFICATIONS MODEL POWER RATING CIRCUIT P70°C W CRA06P 0.0625 03 LIMITING ELEMENT TEMPERATURE TOLERANCE RESISTANCE E-SERIES VOLTAGE MAX. COEFFICIENT V쓖 ppm/°C % Ω 50 200 2, 5 10R-1M0 24 100 1 10R-1M0 24-96 Jumper: Zero-Ohm-Resistor on Request RANGE • Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material • Operating temperature Range: - 55°C to + 150°C • Maximum Working Voltage: 50 volts. Rated continuous working voltage (RCWV) shall be determined from RCWV = square root of Rated Power, Resistance Value or 50 volts whichever is less. • Ask about extended value ranges • Packaging: according to EIA 481 TECHNICAL SPECIFICATIONS PARAMETER UNIT CRA06P 03 CIRCUIT Rated Dissipation at 70°C W 0.0625 Limiting Element Voltage 1) V쓖 50 Insulation Voltage (1min) Vdc/ac peak 100 Category Temperature Range °C - 55 / + 150 Insulation Resistance Ω > 10 10 1) Rated voltage: PxR ORDERING INFORMATION CRA06P MODEL www.vishay.com 8 08 TERMINAL COUNT 03 CIRCUIT TYPE 08 03 Isolated only. 105 RESISTANCE VALUE First 2 digits are significant figures, the last digit is the multiplier. For Technical Questions, contact: [email protected] J TOLERANCE J = ± 5% G = ± 2% F = ± 1% Z = 0Ω Jumper RT1 PACKAGING Paper tape. 5000 piece reels. Document Number 31047 Revision 05-Sep-03 CRA06P Thick Film, Resistor Array Vishay Dale DIMENSIONS in inches [millimeters] 4-Resistor Device a c 8 PIN L A B C P T W mm 3.20 0.30 0.40 0.40 0.80 0.60 1.6 Tol ± 0.20 ± 0.20 ± 0.15 ± 0.20 - w p b L t DIMENSIONS ± 0.10 ± 0.15 SOLDER PAD DIMENSIONS [in millimeters] c c w p a b 0.8 2.6 0.8 0.4 0.9 w WAVE b a Rated Power % p CIRCUIT SCHEMATICS 03 Circuit CRA06P 120 100 80 60 40 20 0 8-pin -55 -25 0 25 Derating 50 75 100 125 150 70 Ambient Temperature °C PERFORMANCE TEST CONDITIONS OF TEST Endurance Test at 70°C per EIA 575-3.14 1000 hours at 70°C, 1.5 hours "ON", 0.5 hours "OFF" ± 1.0% Overload per EIA 575-3.6 Short time overload ± 0.5% Thermal Shock per EIA 575-3.5 ± 0.5% Moisture Resistance per EIA 575-3.10 ± 1.0% Resistance to Soldering Heat EIA 575 3.8 10 seconds at 260°C solder bath temperature ± 1.0% High Temperature Exposure per EIA 575-3.7 ± 1.0% Low Temperature Operation per EIA-/ IS-30A-3.6 ± 0.5% Solderability & Leaching EIA 575-3.12 Document Number 31047 Revision 05-Sep-03 For Technical Questions, contact: [email protected] TEST RESULTS 95% Coverage www.vishay.com 9 CRA12E and S Vishay Dale Thick Film, Resistor Array FEATURES • Convex terminal array available with either scalloped corners (E version) or square corners (S version) • 4, 8, 10, or 16 terminal package with either isolated resistors or bussed resistors • Single component reduces board space and component counts • Automatic placement capability • Wave and solder paste reflow compatible • Thick film resistance element • Solderable wrap around termination • Nickel barrier for inner electrode protection • Standard E-24 (± 2% and ± 5%) and E-96 (± 1%) resistance values • Operating temperature range of -55°C to +150°C • Consult factory for additional schematics, values, etc STANDARD ELECTRICAL SPECIFICATIONS MODEL POWER RATING CRA12E & S CIRCUIT LIMITING ELEMENT TEMPERATURE TOLERANCE P70°C VOLTAGE MAX COEFFICIENT W V쓖 ppm/°C 0.100 01, 02, 20 0.125 03 50 RESISTANCE E-SERIES RANGE % Ω 200 2, 5 10R – 1M0 24 100 1 10R – 1M0 24 – 96 Jumper: Zero Ohm Resistor on Request • • • • • Power rating depends on the max. temperature at the solder point , the component placement density and the substrate material Operating temperature Range: - 55°C to +150°C Ask aboout further value ranges Packaging: according to EIA 481 100ppm TC is standard with 1% values and 200ppm TC is standard for 5% values TECHNICAL SPECIFICATIONS PARAMETER Rated Dissipation at 70°C Limiting Element Voltage1) UNIT CRA12E & S 01 / 02 / 20 CIRCUIT CRA12E & S 03 CIRCUIT W 0.1 0.125 V쓖 50 Vdc/ac peak 100 Category Temperature Range °C - 55 / + 150 Insulation Resistance Ω > 10 9 Insulation Voltage (1min) 1)Rated voltage: PxR ORDERING INFORMATION CRA12E 04 01 MODEL TERMINAL COUNT CIRCUIT TYPE CRA12E CRA12S 04, 08, 10, 16 08, 10 01, 02, 03, 20 01, 02, 03, 20 www.vishay.com 10 105 G RB8 R-VALUE TOLERANCE PACKAGING Ω ±% First two digits (three for 1%) F = ± 1% Paper tape 2000pcs are significant. Last digit is the G = ± 2% multipier J = ± 5% Z = 0Ω Jumper For Technical Questions, contact: [email protected] Document Number 31003 Revision 03-Sep-03 CRA12E and S Vishay Dale Thick Film, Resistor Array 8-Terminal device S - Version E - Version * 103 PIN 1 103 A d e MODEL PIN CRA NO# L 12E 4 2.54 12E 8 5.08 12S 8 5.08 12E 10 6.40 12S 10 6.40 12E 16 10.30 Tol - 0.15 a a e DIMENSIONS [in millimetres] A A* B B* P T 0.79 0.51 0.38 1.27 0.53 0.79 0.51 0.38 1.27 0.53 0.79 0.89 0.51 0.38 1.27 0.53 0.79 0.51 0.38 1.27 0.53 0.79 0.89 0.51 0.38 1.27 0.53 0.79 0.51 0.38 1.27 0.53 - 0.15 - 0.15 - 0.25 - 0.2 - 0.1 - 0.1 SOLDER PAD DIMENSIONS [in millimetres] W 3.05 3.05 3.05 3.05 3.05 3.05 - 0.15 c w d p a b e WAVE 2.2 4.3 0.57 1.27 0.71 1.05 1.09 REFLOW 2.2 3.9 0.57 1.27 0.71 0.86 1.09 The dimensions shown are for 8 pin part. For parts with different pin numbers use the same pitch and add or substract pads as required. CIRCUIT SCHEMATICS 02 Circuit Rated Power In % 01 Circuit 120 100 80 60 16 pin Pin 1 4 pin8 pin10 pin 03 Circuit Pin 1 4 pin 8 pin 10 pin 20 Circuit 40 20 0 - 55 -25 0 25 Derating 50 75 100 125 150 175 70 Ambient Temperature in °C pin # 1 4 4 pin 8 pin 10 pin 16 pin PERFORMANCE TEST CONDITIONS OF TEST Endurance Test at 70°C per EIA 575-3.14 1000 hours at 70˚C, 1.5 hours "ON", 0.5 hours "OFF" ± 1.0% Overload per EIA 575-3.6 Short time overload 2.5 x rated continuous working voltage for 5 seconds. Not to exceed 2 x max operating voltage ± 0.5% Thermal Shock per EIA 575-3.5 ± 0.5% Moisture Resistance per EIA 575-3.10 ± 1.0% Resistance to Soldering Heat EIA 575-3.8 10 seconds at 260°C solder bath temperature ± 2.0% High Temperature Exposure per EIA 575-3.7 ± 1.0% Low Temperature Operations per EIA 575-3.6 Solderability & Leaching EIA 575-3.12 Document Number 31003 Revision 03-Sep-03 For Technical Questions, contact: [email protected] TEST RESULTS ± 0.5% 95% Coverage www.vishay.com 11 ACAC 0612 Professional Vishay Beyschlag Professional Flat Chip Resistor Array FEATURES ∑ Advanced thin film technology ∑ Superior overall stability ∑ Case sizes: – Imperial: 0612 – Metric: RR 1632M ∑ Four resistors on one substrate ∑ Tight T.C. of ± 50 ppm/K ∑ Tolerance of ± 1 % ∑ Different resistance values are possible with a maximum ratio of 1:10 Rmin/Rmax ∑ Green product, supports lead-free soldering. ACAC 0612 flat chip resistor array combines the proven reliability of professional MFC products with the advantages of a chip array. A small package enables the design of high density circuits in combination with reduction of assembly costs. Different resistance values can be realized on one substrate. APPLICATIONS ∑ Bus terminations ∑ Voltage divider ∑ Feedback circuits ∑ Signal conditioning. TECHNICAL SPECIFICATIONS ACAC 0612 DESCRIPTION EIA size 0612 Metric size RR 1632M Configuration, isolated Design: 4 x 0603 all equal AE two pairs TP different values DF 100 W to 221 kW (1) Resistance values Tolerance: ±1 % absolute Temperature coefficient: ± 50 ppm/K (± 25 ppm/K on request) absolute 1:10 (2) Max. resistance ratio Rmin/Rmax Climatic category (LCT/UCT/days) 55/125/56 Rated dissipation: P70(3) element 0.1 W package 0.3 W Operating voltage 75 V Film temperature Insulation voltage (Uins) against ambient and between isolated resistors, continuous 125 ∞C 75 V Notes 1. Resistance values to be selected from E24 and E96. 2. Higher ratio on request. 3. The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature is not exceeded. www.vishay.com 12 For technical questions contact: [email protected] Document Number:28706 Revision: 08-Mar-04 ACAC 0612 Professional Vishay Beyschlag Professional Flat Chip Resistor Array ORDERING INFORMATION - type description and ordering code A TYPE A = Array C PRODUCT CODE C = Flat chip A SIZE CODE A = 0612 C TERMINATION C = Concave 1234 DESIGN NUMBER 4-Digits TP DESIGN P5 PACKAGING AE = All Equal P5 = 5 000 units in paper tape on reel PW = 10 000 units in paper tape on reel TP = Two Pairs DF = Different Values Note : We recommend that the clear text ordering code is used to minimize the possibility of errors in order handling. DIMENSIONS WT I WT d P I d P T T L L W W Bottom view Top view DIMENSIONS - CHIP resistor array top view, mass and relevant physical dimensions TYPE L (mm) W (mm) H (mm) P (mm) WT (mm) T (mm) D (mm) I (mm) MASS (mg) ACAC 0612 1.6 ± 0.15 3.2 ± 0.15 0.55 ± 0.1 0.8 ± 0.1 0.6 ± 0.15 0.3 ± 0.15 0.3 ± 0.1 min. 0.15 9.41 DIMENSIONS - CHIP resistor array bottom view, mass and relevant physical dimensions TYPE L (mm) W (mm) H (mm) P (mm) WT (mm) T (mm) D (mm) I (mm) MASS (mg) ACAC 0612 1.6 ± 0.15 3.2 ± 0.15 0.55 ± 0.1 0.8 ± 0.1 0.6 ± 0.15 0.4 ± 0.15 0.3 ± 0.1 min. 0.25 9.41 APPLICATION INFORMATION R1 R2 R3 R4 R1 R2 R3 R4 Equivalent circuit. Array configuration. Document Number:28706 Revision: 08-Mar-04 For technical questions contact: [email protected] www.vishay.com 13 ACAC 0612 Professional Vishay Beyschlag Professional Flat Chip Resistor Array DESCRIPTION ASSEMBLY Production is strictly controlled and follows an extensive set The resistors are suitable for processing on automatic SMD of A assembly systems and for automatic soldering using wave, homogeneous film of metal alloy is deposited on a super reflow or vapour phase. The encapsulation is resistant to all high grade (96 % Al2 O3) ceramic substrate and conditioned cleaning solvents commonly used in the electronics industry, to achieve the desired temperature coefficient. Specially including alcohols, esters and aqueous solutions. The designed inner contacts are deposited on both sides. A resistors are lead (Pb)-free, the pure tin plating provides special laser is used to achieve the target value by smoothly compatibility with lead (Pb)-free and lead-containing cutting a meander groove in the resistive layer without soldering processes. The immunity of the plating against tin damaging the ceramics. whisker growth has been proven under extensive testing. All instructions established for reproducibility. products comply with the CEFIC-EECA-EICTA list of legal The resistor elements are covered by a protective coating restrictions on hazardous substances. designed for electrical, mechanical and climatic protection. The terminations receive a final pure tin on nickel plating. This includes full compatibility with the following directives: ∑ 2000/53/EC End of Vehicle life Directive (ELV) The result of the determined production is verified by an extensive testing procedure and optical inspection performed on 100 % of the individual chip resistors. Only accepted products are laid directly into the paper tape in accordance with EN 60 286-3. ∑ 2000/53/EC Annex II to End of Vehicle Life Directive (ELV II) ∑ 2002/95/EC Restriction of the use of Hazardous Substances Directive (RoHS) ∑ 2002/96/EC Waste Electrical and Electronic Equipment Directive (WEEE) Solderability is specified for 2 years after production or re-qualification. The permitted storage time is 20 years. APPROVALS Where applicable, the resistors are tested in accordance with EN 140 401-801 (superseding CECC 40401-801) which refers to EN 140 000 (EN 60 115-1) and EN 140 400 (IEC 60 115-8). www.vishay.com 14 For technical questions contact: [email protected] Document Number:28706 Revision: 08-Mar-04 ACAC 0612 Professional Vishay Beyschlag Professional Flat Chip Resistor Array TESTS AND REQUIREMENTS Essentially all tests are carried out in accordance with the following specifications: Unless otherwise specified the following values apply: Temperature: 15 ˚C to 35 ˚C EN 140 000 / EN 60 115-1, Generic specification (includes tests) Relative humidity: 45 % to 75 % Air pressure: 86 kPa to 106 kPa (860 mbar to 1 060 mbar). EN 140 400 / EN 60 115-1, Sectional specification (includes schedule for qualification approval) The components are mounted for testing on boards in accordance with EN 60 115-1, 4.31 unless otherwise specified. The testing also covers most of the requirements specified by EIA/IS-703 and JIS-C-5202. In the Test Procedures and Requirements table below, only the tests and requirements are listed with reference to the relevant clauses of EN 60 115-1 and IEC 60 068-2; a short description of the test procedure is also given. The tests are carried out in accordance with IEC 60 068 and under standard atmospheric conditions according to IEC 60 068-1, 5.3. Climatic category LCT/UCT/56 (rated temperature range: Lower Category Temperature, Upper Category Temperature; damp heat, long term, 56 days) is valid. TEST PROCEDURES AND REQUIREMENTS EN 60115-1 CLAUSE IEC 60068-2 TEST METHOD TEST REQUIREMENTS(1) PERMISSIBLE CHANGE (DR/R) PROCEDURE stability for product types: ACAC 0612 4.5 - resistance - 4.8.4.2 - temperature coefficient at 20 / LCT / 20 ∞C and 100 W to 221 kW ±1 % ± 50 ppm/K 20 / UCT / 20 ∞C 4.25.1 - U= endurance P 70 ¥ R or U = Umax; ± (0.25 %R + 0.05 W) 1.5 h on; 0.5 h off; 70 ∞C; 1 000 h 4.25.3 - endurance at upper 125 ∞C; 1 000 h ± (0.5 %R + 0.05 W) (40 ± 2) ∞C; 56 days; ± (0.5 %R + 0.05 W) category temperature 4.24 78 (Cab) damp heat, steady state (93 ± 3) % RH Document Number:28706 Revision: 08-Mar-04 For technical questions contact: [email protected] www.vishay.com 15 ACAC 0612 Professional Vishay Beyschlag Professional Flat Chip Resistor Array TEST PROCEDURES AND REQUIREMENTS - continued EN 60115-1 CLAUSE IEC 60068-2 TEST METHOD TEST REQUIREMENTS(1) PERMISSIBLE CHANGE (DR/R) PROCEDURE stability for product types: ACAC 0612 100 W to 221 kW 4.13 - short time overload (2) U = 2.5 ¥ P 70 ¥ R or U = 2 ¥ Umax; 5 s ± (0.1 %R + 0.01 W) no visible damage 4.19 14 (Na) rapid change of temperature 30 min. at LCT and 30 min. at UCT; 5 cycles ± (0.1 %R + 0.01 W) no visible damage 4.18.2 58 (Tb) resistance to soldering heat (260 ± 5) ∞C; (10 ± 1) s ± (0.25 %R + 0.01 W) no visible damage 4.17.2 58 (Ta) solderability solder bath method; (215 ± 3) ∞C; (3 ± 0.3) s good tinning (≥ 95 % covered); no visible damage 4.32 21 (Ue3) shear (adhesion) RR 1632 M; 45 N 4.7 - voltage proof Urms = Uins; 60 ± 5 s; no visible damage no flashover or breakdown against ambient, between adjacent resistors Notes 1. Figures are given for equal values. 2. For a single element. www.vishay.com 16 For technical questions contact: [email protected] Document Number:28706 Revision: 08-Mar-04 ACAC 0612 Professional Professional Flat Chip Resistor Array Vishay Beyschlag ORDERING INFORMATION Components may be ordered by using either a simple clear text ordering code, see “Type description and ordering code” or Vishay BCcomponents’ unique 12NC. Numeric Ordering code (12NC) ∑ The arrays have a 12-digit ordering code starting with 2312. ∑ The subsequent 3 digits indicate the array package and body size; see the 12NC Ordering Code table . ∑ The last 5 digits indicate the termination and individual array design number (last 4 digits). 12NC ORDERING CODE - resistor array type and packaging ORDERING CODE 2312 ... ..... DESCRIPTION TYPE ACAC 0612 T.C. ± 50 ppm/K TOL. ±1% AE (ALL EQUAL) TP (TWO PAIRS) R1; R4 R2; R3 P5 5 000 UNITS P5 5 000 UNITS 1 kW 1 kW 441 09011 - 10 kW 10 kW 441 09012 - 100 kW 100 kW 441 09013 - 1 kW 2 kW - 441 19014 10 kW 20 kW - 441 19015 1 kW 3 kW - 441 19016 10 kW 30 kW - 441 19017 Note 1. 12NC Ordering Code Indicating Resistor Array Type and Packaging table shows standard array types with a resistance divider ratio up to 1:3. Please consult Vishay Beyschlag for specific divider ratio, temperature coefficient, tolerance and ohmic values. Document Number:28706 Revision: 08-Mar-04 For technical questions contact: [email protected] www.vishay.com 17 ACAC 0612 - Precision Vishay Beyschlag Flat Chip Resistor Array FEATURES ∑ Advanced thin film technology ∑ Superior overall stability ∑ Case sizes: – Imperial: 0612 – Metric: RR 1632M ∑ Four resistors on one substrate ∑ Tight T.C. of ± 25 ppm/K and T.C. tracking of 15 ppm/K, (10 ppm/K on request) ∑ Tolerance of ± 0.25 % and matched tolerance of 0.1 % ACAC 0612 flat chip resistor array combines the proven reliability of precision MFC products with the advantages of a chip array. The possibility of tolerance matching and T.C. tracking makes this product perfectly suited for applications with outstanding requirements towards stable fixed resistor ratios. A small package enables the design of high density circuits in combination with reduction of assembly costs. Different resistance values can be realized on one substrate. ∑ Different resistance values are possible with a maximum ratio of 1:5 Rmin/Rmax ∑ Green product, supports lead-free soldering. APPLICATIONS ∑ Precision analogue circuits ∑ Voltage divider ∑ Feedback circuits ∑ Signal conditioning. TECHNICAL SPECIFICATIONS DESCRIPTION EIA size Metric size Configuration, isolated Design: all equal two pairs different values Resistance values Tolerance: absolute matching Temperature coefficient: absolute tracking Max. resistance ratio Rmin/Rmax Climatic category (LCT/UCT/days) Rated dissipation: P70(2) element package Operating voltage Film temperature Insulation voltage (Uins) against ambient and between isolated resistors, continuous ACAC 0612 0612 RR 1632M 4 ¥ 0603 AE TP DF 100 W to 221 kW(1) ± 0.25 % 0.1 % ± 25 ppm/K 15 ppm/K 1:5 55/125/56 0.1 W 0.3 W 75 V 125 ∞C 75 V Note 1. Resistance values to be selected from E24 and E96. 2. The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature is not exceeded. www.vishay.com 18 For technical questions contact: [email protected] Document Number: 28741 Revision: 23-Jul-04 ACAC 0612 - Precision Vishay Beyschlag Flat Chip Resistor Array ORDERING INFORMATION - type description and ordering code A TYPE A = Array C PRODUCT CODE C = Flat Chip A SIZE CODE A = 0612 C TERMINATION C = Concave 1234 DESIGN NUMBER 4-Digits TP DESIGN AE = All Equal TP = Two Pairs DF = Different Values P5 PACKAGING P5 = 5 000 units in paper tape on reel PW = 10 000 units in paper tape on reel Note: We recommend that the clear text ordering code is used to minimize the possibility of errors in order handling. DIMENSIONS WT I WT d P I d P T T L L W W Top view Bottom view DIMENSIONS - CHIP resistor array top view, mass and relevant physical dimensions TYPE L (mm) W (mm) H (mm) P (mm) WT (mm) T (mm) d (mm) I (mm) mass (mg) ACAC 0612 1.6 ± 0.15 3.2 ± 0.15 0.55 ± 0.1 0.8 ± 0.1 0.6 ± 0.15 0.3 ± 0.15 0.3 ± 0.1 min. 0.15 9.41 DIMENSIONS - CHIP resistor array bottom view, mass and relevant physical dimensions TYPE L (mm) W (mm) H (mm) P (mm) WT (mm) T (mm) d (mm) I (mm) mass (mg) ACAC 0612 1.6 ± 0.15 3.2 ± 0.15 0.55 ± 0.1 0.8 ± 0.1 0.6 ± 0.15 0.4 ± 0.15 0.3 ± 0.1 min. 0.25 9.41 APPLICATION INFORMATION R1 R2 R3 R4 R1 R2 R3 R4 Equivalent circuit. Array configuration. Document Number: 28741 Revision: 23-Jul-04 For technical questions contact: [email protected] www.vishay.com 19 ACAC 0612 - Precision Vishay Beyschlag Flat Chip Resistor Array DESCRIPTION ASSEMBLY Production is strictly controlled and follows an extensive set The resistors are suitable for processing on automatic SMD of A assembly systems and for automatic soldering using wave, homogeneous film of metal alloy is deposited on a super instructions established for reproducibility. reflow or vapour phase. The encapsulation is resistant to all high grade (96 % Al2 O3) ceramic substrate and conditioned cleaning solvents commonly used in the electronics industry, to achieve the desired temperature coefficient. Specially including alcohols, esters and aqueous solutions. The designed inner contacts are deposited on both sides. A resistors are lead (Pb)-free, the pure tin plating provides special laser is used to achieve the target value by smoothly compatibility with lead (Pb)-free and lead-containing cutting a meander groove in the resistive layer without soldering processes. The immunity of the plating against tin damaging the ceramics. whisker growth has been proven under extensive testing. All The resistor elements are covered by a protective coating designed for electrical, mechanical and climatic protection. products comply with the CEFIC-EECA-EICTA list of legal restrictions on hazardous substances: The terminations receive a final pure tin on nickel plating. This includes full compatibility with the following directives: The result of the determined production is verified by an ∑ 2000/53/EC End of Vehicle life Directive (ELV) extensive ∑ 2000/53/EC Annex II to End of Vehicle Life Directive (ELV II) testing procedure and optical inspection performed on 100 % of the individual chip resistors. Only accepted products are laid directly into the paper tape in accordance with EN 60 286-3. ∑ 2002/95/EC Restriction of the use of Hazardous Substances Directive (RoHS) ∑ 2002/96/EC Waste Electrical and Electronic Equipment Directive (WEEE) Solderability is specified for 2 years after production or re-qualification. The permitted storage time is 20 years. APPROVALS Where applicable, the resistors are tested in accordance with EN 140 401-801 (superseding CECC 40401-801) which refers to EN 140 000 (EN 60 115-1) and EN 140 400 (IEC 60 115-8). www.vishay.com 20 For technical questions contact: [email protected] Document Number: 28741 Revision: 23-Jul-04 ACAC 0612 - Precision Vishay Beyschlag Flat Chip Resistor Array TESTS AND REQUIREMENTS Essentially all tests are carried out in accordance with the Unless otherwise specified the following values apply: following specifications: Temperature: 15 ∞C to 35 ∞C EN 140 000 / EN 60 115-1, Generic specification Relative humidity: 45 % to 75 % (includes tests) Air pressure: 86 kPa to 106 kPa (860 mbar to 1 060 mbar). EN 140 400 / EN 60 115-1, Sectional specification The components are mounted for testing on boards in (includes schedule for qualification approval) The testing also covers most of the requirements specified by EIA/IS-703 and JIS-C-5202. accordance with EN 60 115-1, 4.31 unless otherwise specified. The tests are carried out in accordance with IEC 60 068 and In the following table only the tests and requirements are under standard atmospheric conditions according to listed with reference to the relevant clauses of EN 60 115-1 IEC 60 068-1, 5.3. Climatic category LCT/UCT/56 (rated and IEC 60 068-2; a short description of the test procedure temperature range: Lower Category Temperature, Upper is also given. Category Temperature; damp heat, long term, 56 days) is valid. TEST PROCEDURES AND REQUIREMENTS EN 60115-1 CLAUSE IEC 60068-2 TEST METHOD TEST PROCEDURE REQUIREMENTS (1) PERMISSIBLE CHANGE (DR/R) stability for product types: ACAC 0612 4.5 - resistance - 4.8.4.2 - temperature coefficient at 20 / LCT / 20 ∞C and 100 W to 221 kW ± 0.25 % ± 25 ppm/K 20 / UCT / 20 ∞C 4.25.1 - U= endurance P 70 ¥ R ± (0.25 %R + 0.05 W) or U = Umax; 1.5 h on; 0.5 h off; 70 ∞C; 1 000 h 4.25.3 - endurance at upper category temperature 125 ∞C; 1 000 h ± (0.5 %R + 0.05 W) 4.24 78 (Cab) damp heat, steady state (40 ± 2) ∞C; 56 days; ± (0.5 %R + 0.05 W) Document Number: 28741 Revision: 23-Jul-04 (93 ± 3) % RH For technical questions contact: [email protected] www.vishay.com 21 ACAC 0612 - Precision Vishay Beyschlag Flat Chip Resistor Array TEST PROCEDURES AND REQUIREMENTS - continued EN 60115-1 CLAUSE IEC 60068-2 TEST METHOD TEST PROCEDURE REQUIREMENTS (1) PERMISSIBLE CHANGE (DR/R) stability for product types: ACAC 0612 4.13 4.19 4.18.2 - 14 (Na) 58 (Tb) short time overload (2) U = 2.5 ¥ P 70 ¥ R or 100 W to 221 kW ± (0.1 %R + 0.01 W) U = 2 ¥ Umax; 5 s no visible damage rapid change of temperature 30 min. at LCT and ± (0.1 %R + 0.01 W) 30 min. at UCT; 5 cycles no visible damage resistance to soldering heat reflow method 2 (IR / forced gas convention); (260 ± 5) ∞C; ± (0.1 %R + 0.01 W) no visible damage (10 ± 1) s 4.17.2 58 (Ta) solderability solder bath method; (215 ± 3) ∞C; good tinning (≥ 95 % covered); no visible damage (3 ± 0.3) s 4.32 21 (Ue3) shear (adhesion) RR 1632M; 45 N 4.7 - voltage proof Urms = Uins; no visible damage no flashover or breakdown 60 ± 5 s; against ambient, between adjacent resistors Note 1. Figures are given for equal values. 2. For a single element. www.vishay.com 22 For technical questions contact: [email protected] Document Number: 28741 Revision: 23-Jul-04 ACAC 0612 - Precision Vishay Beyschlag Flat Chip Resistor Array ORDERING INFORMATION Components may be ordered by using either a simple clear Numeric ordering code (12NC) text ordering code, see “Type description and ordering code” ∑ The arrays have a 12-digit ordering code starting with 2312. or Vishay BCcomponents’ unique 12NC. ∑ The subsequent 3 digits indicate the array package and body size; see the 12NC Ordering Code table. ∑ The last 5 digits indicate the termination and individual array design number (last 4 digits). 12NC ORDERING CODE - resistor array type and packaging ORDERING CODE 2312 ... ..... DESCRIPTION TYPE ACAC 0612 T.C. 15 ppm/K TOL. 0.1 % AE (ALL EQUAL) TP (TWO PAIRS) R1; R4 R2; R3 P5 5 000 UNITS P5 5 000 UNITS 1 kW 1 kW 441 09001 - 10 kW 10 kW 441 09002 - 100 kW 100 kW 441 09003 - 1 kW 2 kW - 441 19004 10 kW 20 kW - 441 19005 1 kW 3 kW - 441 19006 10 kW 30 kW - 441 19007 Note 1. 12NC Ordering Code Indicating Resistor Array Type and Packaging table shows standard array types with a resistance divider ratio up to 1:3. Please consult Vishay BEYSCHLAG for specific divider ratio, temperature coefficient, tolerance and ohmic values. Document Number: 28741 Revision: 23-Jul-04 For technical questions contact: [email protected] www.vishay.com 23 TRA06E Vishay Dale Thin Film, Resistor Array FEATURES • Flow solderable • Automatic placement capability • Inner electrode protection • Wrap around termination • Low noise, high frequency applications STANDARD ELECTRICAL SPECIFICATIONS MODEL POWER RATING P70°C W CIRCUIT 0.063 03 TRA06E LIMITING ELEMENT VOLTAGE MAX. V쓖 TEMPERATURE COEFFICIENT TOLERANCE RESISTANCE RANGE ppm/°C % Ω 25 0.1, 0.5, 1 100R - 33K 50 0.5, 1 10R - 91R 100 0.5, 1 36K - 330K 50 E-SERIES 24 • Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material • TC temperature range: - 55°C to + 125°C • Packaging: according to EIA 481 TECHNICAL SPECIFICATIONS PARAMETER UNIT TRA06E SCHEMATIC 03 Rated Dissipation at 70°C W 0.063 Limiting Element Voltage 1) V쓖 50 ppm/°C ± 10 ± 50 to ± 100 °C - 55 / + 150 ppm/Volt < 0.1 TCR Tracking Absolute Category Temperature Range Voltage Coefficient 1) Rated voltage: PxR ORDERING INFORMATION TRA06E 08 03 101 F RT1 MODEL TERMINAL COUNT CIRCUIT TYPE R-VALUE Ω TOLERANCE ±% PACKAGING Papertape 5000pcs 08 03 First two digits (three for 1%) are significant. Last digit is the multiplier www.vishay.com 24 B = 0.1% D = ± 0.5% F = ± 1% For Technical Questions, contact: [email protected] Document Number 31054 Revision 05-Apr-04 TRA06E Vishay Dale Thin Film Resistor Array DIMENSIONS 8-Terminal device PIN E - Version DIMENSIONS [in millimeters] NO:# 8 L PIN CIRCUIT SCHEMATIC 03 Circuit B P T 0.8 ± 0.1 W 0.4 ± 0.1 1.6 ± 0.15 SOLDER PAD DIMENSIONS [in millimeters] NO:# c w d p a b 8 0.8 3.1 0.36 0.8 0.44 1.15 Rated Power % Pin 1 A 3.2 ± 0.3 0.5 ± 0.1 0.3 ± 0.2 120 100 80 60 40 20 0 - 55 -25 0 25 Derating 50 75 70 100 125 150 175 Ambient Temperature °C PERFORMANCE TEST CONDITIONS OF TEST Endurance Test at 70°C per EIA 575-3.14 1000 hours at 70°C, 1.5 hours "ON", 0.5 hours "OFF" ± 3.0% Overload per EIA 575-3.6 Short time overload ± 2.0% Thermal Shock per EIA 575-3.5 ± 1.0% Moisture Resistance per EIA 575-3.10 ± 1.0% Resistance to Soldering Heat EIA 575-3.8 10 seconds at 260°C solder bath temperature ± 2.0% High Temperature Exposure per EIA 575-3.7 ± 3.0% Low Temperature Operations per EIA-575-3.6 ± 1.0% Solderability & Leaching EIA 575-3.12 Document Number 31054 Revision 05-Apr-04 For Technical Questions, contact: [email protected] TEST RESULTS 95% Coverage www.vishay.com 25 CRCA Vishay Dale Thick Film Array, Resistor / Capacitor FEATURES • Single component reduces board space and component counts • Choice of dielectric characteristics X7R or Y5U • Wrap around termination • Thick film R/C element • Inner electrode protection • Flow & Reflow solderable • Automatic placement capability, standard size • 8 or 10 pin configurations STANDARD ELECTRICAL SPECIFICATIONS GLOBAL MODEL RESISTOR CAPACITOR POWER RATING TEMPERATURE TOLERANCE VALUE DIELECTRIC TEMPERATURE TOLERANCE VOLTAGE P70°C COEFFICIENT RANGE COEFFICIENT RATING W ppm/°C % Ω % % VDC 0.125 200 5 10R – 1M0 X7R ± 15 20 50 CRCA12E CRCA12S CRCA12E CRCA12S 0.125 200 5 10R – 1M0 RESISTOR • Operating Temperature Range: - 55°C to + 125°C • Technology: Thick Film Y5U + 20, - 56 20 VALUE RANGE pF 10 - 270 50 270 -1800 CAPACITOR • Operating Temperature Range: X7R - 55°C to + 125°C Y5U - 30°C to + 85°C • Maximum Dissipation Factor: 2.5% • Dielectric Withstanding Voltage: 125Vdc , 5 sec, 50mA Charge • Ask about extended value ranges • Packaging: according to EIA 481 • Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material TECHNICAL SPECIFICATIONS PARAMETER Rated Dissipation at 70°C (CECC 40401 I EIA 575) Capacitor Voltage Rating Dielectric Withstanding Voltage (5 sec, 50mA Charge) Category Temperature Range Insulation Resistance UNIT RESISTOR X7R CAPACITOR Y5U CAPACITOR W 0.125 – – V – 50 50 Vdc – 125 125 °C Ω - 55 / + 155 - 55 / + 125 > 1010 - 30 / + 85 GLOBAL PART NUMBER INFORMATION New Global Part Numbering: CRCA12E081472220R (preferred part numbering format) C R C A 1 2 E MODEL PIN COUNT SCHEMATIC CRCA12E CRCA12S 08 = 8 Pin 10 = 10 Pin 1 = 01 2 = 02 3 = 03 0 = Special 0 8 1 4 7 2 RESISTANCE CAPACITANCE VALUE VALUE 2 digit significant 2 digit significant figure, followed by figure, followed by a multiplier a multiplier 100 = 10Ω 100 = 10pF 683 = 68KΩ 271 = 270pF 105 = 1.0MΩ 182 = 1800pF (Tolerance = ± 5%) (Tolerance = ± 20%) 2 2 0 R PACKAGING SPECIAL E = Lead Free, T/R (2000pcs) R = Tin/Lead, T/R (2000pcs) (Dash Number) (up to 1 digit) Blank = Standard Historical Part Number example: CRCA12E0801472J220MRB8 (will continue to be accepted) CRCA12E 08 01 472 J 220 M RB8 MODEL PIN COUNT SCHEMATIC RESISTANCE VALUE TOLERANCE CAPACITANCE VALUE TOLERANCE PACKAGING www.vishay.com 26 For Technical Questions, contact: [email protected] Document Number 31044 Revision 09-Sep-04 CRCA Thick Film Array, Resistor / Capacitor Vishay Dale DIMENSIONS 8-Terminal device GLOBAL MODEL PIN NO# S-Version E-Version SIZE DIMENSIONS [in millimeters] INCH METRIC L W T B B* A A* DNOM PNOM – 0.25 1.27 CRCA12E 8 2012 5032 5.1 ± 0.15 3.05 ± 0.15 0.61 ± 0.10 0.51 ± 0.25 0.38 ± 0.2 0.79 ± 0.15 CRCA12S 8 2012 5032 5.1 ± 0.15 3.05 ± 0.15 0.61 ± 0.10 0.51 ± 0.25 0.38 ± 0.2 0.79 ± 0.15 0.89 ± 0.15 0.25 1.27 CRCA12E 10 2512 6432 6.4 ± 0.15 3.05 ± 0.15 0.61 ± 0.10 0.51 ± 0.25 0.38 ± 0.2 0.79 ± 0.15 0.25 1.27 CRCA12S 10 2512 6432 6.4 ± 0.15 3.05 ± 0.15 0.61 ± 0.10 0.51 ± 0.25 0.38 ± 0.2 0.79 ± 0.15 0.89 ± 0.15 0.25 1.27 – SOLDER PAD DIMENSIONS [in millimeters] WAVE SOLDERING c 2.2 * REFLOW SOLDERING w d p a b* c w d p a b* 4.3 0.57 1.27 0.71 1.05 2.2 3.9 0.57 1.27 0.71 0.86 For layouts to accept both the edge type and pull through type terminations add 0.25mm to the b-dimension and c = 1.7mm PERFORMANCE: see CRCC1206 01 Circuit CRCA12E & S 10 Pin only Document Number 31044 Revision 09-Sep-04 02 Circuit CRCA12E & S 10 Pin only For Technical Questions, contact: [email protected] 03 Circuit CRCA12E & S 8 Pin 10 Pin www.vishay.com 27 CZA Vishay Dale Surface Mount Chip Resistor Attenuator FEATURES • Single component reduces board space and component counts - replaces 3 or more components • Tolerance matching and temperature tracking superior to individual components • Maximum power dissipation: 0.075 Watts for CZA06S; 0.040 Watts for CZA04S • Consult factory for extended values, non-standard tolerances, impedance matching and other attenuation values • Frequency range: DC to 3GHz STANDARD ELECTRICAL SPECIFICATIONS GLOBAL MODEL IMPEDANCE 50 ± 0.3 dB (L) 1 - 5 dB ± 0.5 dB (H) CZA04S POWER RATING P70°C W 0.040 ATTENUATION RANGE AND TOLERANCE CZA06S 0.075 50 / 75 / 100 / 300 / 600 1 - 5 dB 6 - 20 dB Ω 6 - 20 dB • Power rating depends on the maximum temperature at the solder point, the component placement density and the substrate material 50Ω 1 1.5 2 3 4 5 6 10 11 12 13 14 15 16 17 18 19 20 IMPEDANCE Attenuation in dB 75Ω 1 1.5 2 3 4 5 6 10 11 12 13 14 15 16 17 18 19 20 100Ω 1 1.5 2 3 4 5 6 10 11 12 13 14 15 16 17 18 19 20 300Ω 1 1.5 2 3 4 5 6 10 11 12 13 14 15 16 17 18 19 20 600Ω 1 1.5 2 3 4 5 6 10 11 12 13 14 15 16 17 18 19 20 4-PIN CIRCUIT CZA04S: (Marking) 1 R1 2 R2 R2 4 3 Unbalanced π Type CZA06S: (Marking) 4 R1 3 R2 R2 2 1 Unbalanced π Type TECHNICAL SPECIFICATIONS PARAMETER Rated Dissipation at 70°C VSWR Category Temperature Range Frequency Range UNIT W CZA04S 0.040 1.2 max. - 55 / + 125 DC to 3GHz °C CZA06S 0.075 1.2 max. - 55 / + 150 DC to 3GHz GLOBAL PART NUMBER INFORMATION New Global Part Numbering: CZA06S04015050LRT (preferred part numbering format) C Z A 0 6 S 0 4 0 1 5 0 5 0 L R T MODEL PIN COUNT ATTENUATION IMPEDANCE TOLERANCE PACKAGING SPECIAL CZA04S CZA06S 04 = 4 Pin 010 = 1.0dB 015 = 1.5dB 020 = 2.0dB 150 = 15.0dB 000 = 0Ω Jumper 050 = 50Ω 075 = 75Ω 100 = 100Ω 000 = 0Ω Jumper H = ±0.5dB L = ±0.3dB Z = 0Ω Jumper EA = Lead Free, T/R (All) TD = Tin/Lead, T/R (04 only) RT = Tin/Lead, T/R (06 only) (Dash Number) (up to 1 digit) Blank = Standard Historical Part Number example: CZA06S04015050LRT (will continue to be accepted) CZA 06S 04 015 050 L RT MODEL CASE SIZE PIN COUNT ATTENUATION IMPEDANCE TOLERANCE PACKAGING www.vishay.com 28 For Technical Questions, contact: [email protected] Document Number 31061 Revision 08-Sep-04 CZA Vishay Dale Surface Mount, Chip Attenuator DIMENSIONS 4-Terminal device S – Version CZA04S Pin 1 CZA06S Pin 1 P GLOBAL DIMENSIONS in inches (millimeters) MODEL L W T A P B CZA04S 0.039 ± 0.004 0.039 ± 0.006 0.014 ± 0.004 0.13 ± 0.006 0.026 0.006 ± 0.004 0.010 ± 0.004 [1.00 ± 0.10] [1.00 ± 1.15] [0.36 ± 0.10] [0.33 ± 0.15] [0.65] [0.15 ± 0.10] [0.25 ± 0.10] 0.063 ± 0.006 0.059 ± 0.006 0.020 ± 0.004 0.024 ± 0.006 0.031 0.012 ± 0.006 [1.60 ± 0.15] [1.50 ± 1.15] [0.51 ± 0.10] [0.61 ± 0.15] [0.80] [0.30 ± 0.15] CZA06S B* 0.012 ± 0.006 [0.30 ± 0.15] c w d a b CZA04S 0.018 [0.45] 0.083 [2.10] 0.083 [0.20] 0.018 [0.45] 0.032 [0.82] CZA06S 0.031 [0.80] 0.122 [3.10] 0.014 [0.36] 0.024 [0.63] 0.045 [1.15] Rated Power % Rated Power % SOLDER PAD DIMENSIONS in inches (millimeters) 120 120 100 100 80 80 60 60 40 40 20 20 0 - 55 -25 0 25 Derating CZA04S 50 75 70 100 125 150 175 Ambient Temperature °C 0 - 55 -25 0 25 50 75 70 Derating CZA06S 100 125 150 175 Ambient Temperature °C PERFORMANCE TEST Endurance Test at 70°C per EIA 575-3.14 Overload per EIA 575-3.6 Thermal Shock Moisture Resistance Resistance to Soldering Heat High Temperature Exposure Low Temperature Operations Solderability & Leaching Document Number 31061 Revision 08-Sep-04 CONDITIONS OF TEST 1000 hours at 70°C, 1.5 hours "ON", 0.5 hours "OFF" TEST RESULTS 0.5dB to 5dB 6dB to 20dB ± 0.2dB ± 0.3dB Short time overload ± 0.2dB ± 0.3dB per EIA 575-3.5 per EIA 575-3.10 10 seconds at 260°C solder bath temperature EIA 575 3.8 per EIA 575-3.7 per EIA-575-3.6 EIA 575-3.12 ± 0.2dB ± 0.2dB ± 0.2dB ± 0.3dB ± 0.3dB ± 0.3db For Technical Questions, contact: [email protected] ± 0.2dB ± 0.3dB ± 0.2dB ± 0.3dB 95% Coverage www.vishay.com 29 Vishay www.vishay.com 30 Model Numbers SOGC 01,03,05...32 SOGC 45,46........36 SOMC..................38 DFP.....................40 Surface Mount Resistor Networks SIL, DIL or Custom Configurations • Isolated, Bussed or TTL-Terminator Circuits • High Packaging Density SOGC 01, 03, 05 Vishay Dale Thick Film Resistor Networks, Dual-In-Line Small Outline Molded Dip, 01, 03, 05 Schematics FEATURES • 0.110" [2.79mm] maximum seated height • Rugged, molded case construction • 0.050" [1.27mm] lead spacing • Reduces total assembly costs • Compatible with automatic surface mounting equipment • Uniform performance characteristics • Meets EIA PDP 100, SOGN-0003 outline dimensions • Available in tube pack or tape and reel pack STANDARD ELECTRICAL SPECIFICATIONS GLOBAL MODEL RESISTOR CIRCUIT W @ 70°C SCHEMATIC PACKAGE POWER W @ 70°C TOLERANCE ±% RESISTANCE RANGE Ω OPERATING VOLTAGE VDC TEMPERATURE COEFFICIENT ppm/°C 1.6 1.6 1.6 2.0 2.0 2.0 2 (1, 5*) 2 (1, 5*) 2 (5*) 2 (1, 5*) 2 (1, 5*) 2 (5*) 10-1M0 10-1M0 10-1M0 10-1M0 10-1M0 10-1M0 50 max 50 max 50 max 50 max 50 max 50 max 100 100 100 100 100 100 01 0.1 03 0.19 05 0.1 01 0.1 SOGC20 03 0.19 05 0.1 *Tolerances in brackets available upon request. • 100 milliohm maximum on zero ohm jumper SOGC16 GLOBAL PART NUMBER INFORMATION New Global Part Numbering: SOGC200310K0GDC (preferred part numbering format) S GLOBAL MODEL SOGC O G C 2 0 PIN COUNT SCHEMATIC 16 20 01 = Bussed 03 = Isolated 00 = Special 0 3 1 0 RESISTANCE VALUE R = Decimal K = Thousand M = Million 10R0 = 10Ω 680K = 680KΩ 1M00 = 1.0MΩ K 0 G TOLERANCE CODE F = ± 1% G = ± 2% J = ± 5% S = Special Z = 0Ω Jumper D C PACKAGING SPECIAL EJ = Lead Free, Tube EA = Tin/Lead, Tape & Reel DC = Tin/Lead, Tube RZ = Tin/Lead, Tape & Reel Blank = Standard (Dash Number) (up to 3 digits) From 1-999 as applicable Historical Part Number example: SOGC2003103G (will continue to be accepted) SOGC 20 03 103 G D02 HISTORICAL MODEL PIN COUNT SCHEMATIC RESISTANCE VALUE TOLERANCE CODE PACKAGING New Global Part Numbering: SOGC1605131AGRZ (preferred part numbering format) S GLOBAL MODEL SOGC O G PIN COUNT C 1 6 0 5 1 3 1 A RESISTANCE TOLERANCE VALUE CODE 16 05 = Dual Terminator 3 digit Impedance F = ± 1% 20 code, followed by G = ± 2% Alpha modifier J = ± 5% (see Impedance Codes table) Historical Part Number example: SOGC1605221331G (will continue to be accepted) G SCHEMATIC R Z PACKAGING SPECIAL EJ = Lead Free, Tube EA = Tin/Lead, Tape & Reel DC = Tin/Lead, Tube RZ = Tin/Lead, Tape & Reel Blank = Standard (Dash Number) (up to 3 digits) From 1-999 as applicable SOGC 16 05 221 331 G R61 HISTORICAL MODEL PIN COUNT SCHEMATIC RESISTANCE VALUE 1 RESISTANCE VALUE 2 TOLERANCE CODE PACKAGING www.vishay.com 32 For technical questions contact: [email protected] Document Number: 31506 Revision: 08-Sep-04 SOGC 01, 03, 05 Vishay Dale Thick Film Resistor Networks, Small Outline, Molded DIP DIMENSIONS in inches [millimeters] B 0.105 [2.67] 0.050 [1.27] Non-Accum. Typ. 0.018 [0.457] Typ. 0.100 [2.54] 0.295 [7.49] SOGC 0.010 ± 0.005 [0.254 ± 0.127] 0.006 [0.152] Max. Typ. 0.406 ± 0.012 [10.31 ± 0.305] Pin 1 0.045 [1.14] A 0.045 [1.14] Ref. 0.008 [0.203] 0.028 ± 0.010 [0.711 ± 0.254] Typ. GLOBAL MODEL A B SOGC16 0.440 [11.18] 0.350 [8.89] SOGC20 0.540 [13.72] 0.450 [11.43] TECHNICAL SPECIFICATIONS PARAMETER Package Power Rating (max. at + 70°C) UNIT S0GC16 W 1.6 S0GC20 2.0 TC Tracking (- 55°C to + 125°C) ppm/°C ± 50 Voltage Coefficient of Resistance: ppm/V < 50 typical VDC 50 Operating Temperature Range: °C - 55 to + 125. Storage Temperature Range: °C - 55 to + 150 Maximum Operating Voltage: MECHANICAL SPECIFICATIONS Marking: Marking Resistance to Solvents: Maximum Solder Reflow Temperature: Solderability: Terminals: Body: Document Number: 31506 Revision: 08-Sep-04 Model number, schematic number, value tolerance, pin 1 indicator, date code. Permanency testing per MIL-STD-202, Method 215. + 255°C Per MIL-STD-202, Method 208E. Copper alloy. Solder dipped terminal Molded epoxy. For technical questions contact: [email protected] www.vishay.com 33 SOGC 01, 03, 05 Vishay Dale IMPEDANCE CODES R1 (Ω) CODE R2 (Ω) CODE R1 (Ω) R2 (Ω) 500B 82 130 141A 270 270 750B 120 200 181A 330 390 800C 130 210 191A 330 470 990A 160 260 221B 330 680 101C 180 240 281B 560 560 111C 180 270 381B 560 1.2K 121B 180 390 501C 620 2.7K 121C 220 270 102A 1.5K 3.3K 131A 220 330 202B 3K 6.2K CIRCUIT APPLICATIONS 01 Schematic 15 or 19 resistors with one pin common The SOGCxx01 circuit provides a choice of 15 or 19 nominally equal resistors, each connected between a common lead (16 or 20) and a discrete PC board pin. Commonly used in the following applications: • MOS/ROM Pull-up/Pull-down • TTL Input Pull-down • Open Collector Pull-up • Digital Pulse Squaring • "Wired OR" Pull-up • TTL Unused Gate Pull-up • Power Driven Pull-up • High Speed Parallels Pull-up SOGC16 Pin 1 SOGC20 03 Schematic 8 or 10 isolated resistors The SOGCxx03 circuit provides a choice of 8 or 10 nominally equal resistors with each resistor isolated from all others and wired directly across. Commonly used in the following applications: • "Wired OR" Pull-up • Long-line Impedance Balancing • Power Driven Pull-up • LED Current Limiting • Powergate Pull-up • ECL Output Pull-down • Line Termination • TTL Input Pull-down SOGC16 Pin 1 SOGC20 05 Schematic R1 R1 R2 R1 R2 R1 R2 R1 R2 R1 R1 R2 R1 R1 R2 R1 R2 R2 R1 R2 R1 R2 R1 R2 SOGC16, SOGC20 R2 R1 R2 R2 TTL dual-line terminator; pulse squaring, 14 or 18 pairs of resistors (R1 Resistors are common to leads 16 or 20) (R2 Resistors are common to leads 8 or 10) The SOGCxx05 circuit contains 14 or 18 pairs of resistors. Each pair is connected between ground and a common line. The junctions of these resistor pairs are connected to the input leads. The 05 circuits are designed for TTL dual-line termination and pulse squaring. Pin 1 www.vishay.com 34 For technical questions contact: [email protected] Document Number: 31506 Revision: 08-Sep-04 SOGC 01, 03, 05 Power Rating (Watts) Thick Film Resistor Networks, Small Outline, Molded DIP Vishay Dale SOGC2001, 03, 05 Pkg. 2.0 SOGC1601, 03, 05 Pkg. 1.6 1.0 Single Resistor 0.19 0.10 - 50 Derating SOGCxx03 SOGCxx01 & 05 0 + 25 + 70 + 125 + 150 Ambient Temperature °C PERFORMANCE TEST MAX. ∆R (TYPICAL TEST LOTS) Power Conditioning ± 0.50% ∆R Thermal Shock ± 0.50% ∆R Short Time Overload ± 0.25% ∆R Low Temperature Operation ± 0.25% ∆R Moisture Resistance ± 0.50% ∆R Resistance to Soldering Heat ± 0.25% ∆R Shock ± 0.25% ∆R Vibration ± 0.25% ∆R Load Life ± 0.50% ∆R Terminal Strength ± 0.25% ∆R Insulation Resistance Dielectric Withstanding Voltage Document Number: 31506 Revision: 08-Sep-04 10,000 Megohm (minimum) No evidence of arcing or damage (200 V RMS for 1 minute) For technical questions contact: [email protected] www.vishay.com 35 SOGC 45, 46 Vishay Dale Thick Film Resistor Networks, Dual-In-Line Small Outline Molded Dip 45 & 46 Schematics FEATURES ∑ 0.110" [2.79] maximum seated height ∑ Rugged, molded case construction ∑ 0.050" [1.27] lead spacing ∑ Reduces total assembly costs ∑ Compatible with automatic surface mounting equipment ∑ Uniform performance characteristics ∑ Meets EIA PDP 100, SOGN-0003 outline dimensions ∑ Available in tube pack or tape and reel pack STANDARD ELECTRICAL SPECIFICATIONS GLOBAL MODEL CIRCUIT SCHEMATIC RESISTOR CIRCUIT W @ 70°C PACKAGE POWER W @ 70°C TOLERANCE ±% RESISTANCE VALUES W OPERATING VOLTAGE VDC TEMPERATURE COEFFICIENT ± ppm/°C 45 0.1 1.6 2 180, 270, 820 50 max 100 46 0.1 1.6 2 330, 150, 330 50 max 100 45 0.1 2.0 2 180, 270, 820 50 max 100 46 0.1 2.0 2 330, 150, 330 50 max 100 SOGC16 SOGC20 TECHNICAL SPECIFICATIONS PARAMETER Package Power Rating: (Maximum at + 70°C) UNIT S0GC16 W 1.6 SOGC20 2.0 TC Tracking: (- 55°C to + 125°C) ppm/°C ± 50 Voltage Coefficient of Resistance: ppm/V < 50 typical. Maximum Operating Voltage: VDC 50 Operating Temperature Range: °C - 55 to + 125 Storage Temperature Range: °C - 55 to + 150 MECHANICAL SPECIFICATIONS Marking Model number, schematic number, value, tolerance, pin 1 indicator, date code. Marking Resistance to Solvents Permanency testing per MIL-STD-202, Method 215 Maximum Solder Reflow Temperature + 255°C Solderability Per MIL-STD-202, Method 208E Terminals Copper alloy. Solder dipped terminal Body: Molded epoxy GLOBAL PART NUMBER INFORMATION New Global Part Numbering: SOGC1646DC (preferred part numbering format) S GLOBAL MODEL SOGC O G C PIN COUNT 16 20 1 6 4 6 D C SCHEMATIC 45 = TTL/ECL Translator 46 = Signal Terminator PACKAGING EJ = Lead Free, Tube EA = Lead Free, Tape & Reel DC = Tin/Lead, Tube RZ = Tin/Lead, Tape & Reel SPECIAL Blank = Standard (Dash Number) (up to 3 digits) From 1-999 as applicable Historical Part Number example: SOGC1646 (will continue to be accepted) SOGC 16 46 D02 HISTORICAL MODEL PIN COUNT SCHEMATIC PACKAGING www.vishay.com 36 For technical questions contact: [email protected] Document Number: 31507 Revision: 06-Sep-04 SOGC 45, 46 Vishay Dale Thick Film Resistor Networks, Small Outline, Molded, DIP DIMENSIONS in inches [millimeters] B 0.105 [2.67] 0.050 [1.27] Non-Accum. Typ. 0.018 [0.457] Typ. 0.100 [2.54] Pin 1 0.045 [1.14] 0.008 [0.203] 0.045 [1.14] Ref. A 0.006 [0.152] Max. Typ. 0.406 ± 0.012 [10.31 ± 0.305] 0.295 [7.49] SOGC 0.010 ± 0.005 [0.254 ± 0.127] 0.028 ± 0.010 [0.711 ± 0.254] Typ. GLOBAL MODEL A B SOGC16 0.440 [11.18] 0.350 [8.89] SOGC20 0.540 [13.72] 0.450 [11.43] CIRCUIT APPLICATIONS 45 Schematic TTL Inputs VCC TTL to ECL translator The SOGCxx45 network consists of resistors of 3 different values, internally divided into 6 or 8 identical three (3) resistor sections for TTL to ECL translation. 180W 270W 820W VCC VEE Outputs to ECL Pin 1 SOGC16, SOGC20 46 Schematic 330W 150W 330W Power Rating (Watts) Pin 1 SCSI-BUS signal terminator The SOGCxx46 network consists of resistors of 2 different values, internally divided into 7 or 9 identical three (3) resistor sections for SCSI-BUS terminator applications. SOGC16, SOGC20 PERFORMANCE SOGC20 Pkg. 2.0 TEST SOGC16 Pkg. 1.6 Power Conditioning Thermal Shock Short Time Overload Low Temperature Operation Moisture Resistance Resistance to Soldering Heat Shock Vibration Load Life Terminal Strength Insulation Resistance Dielectric Withstanding Voltage 1.0 Single Resistor 0.10 0.50 Derating Document Number: 31507 Revision: 06-Sep-04 0 + 25 + 70 + 125 + 150 Ambient Temperature ∞C MAX. DR (TYPICAL TEST LOTS) ± 0.50% DR ± 0.50% DR ± 0.25% DR ± 0.25% DR ± 0.50% DR ± 0.25% DR ± 0.25% DR ± 0.25% DR ± 0.50% DR ± 0.25% DR 10,000 Megohm (minimum) No evidence of arcing or damage (200 V RMS for 1 minute) * Test methods per MIL-STD-202. For technical questions contact: [email protected] www.vishay.com 37 SOMC Vishay Dale Thick Film, Dual-in-Line Resistor Networks FEATURES • • • • • • • • 14,16 or 20 terminal package Isolated, bussed or TTL-terminator circuits Molded case construction Highly stable thick film elements Reflow solderable Compatible with automatic surface mounting equipment Reduces total assembly costs For wave flow soldering contact factory STANDARD ELECTRICAL SPECIFICATIONS GLOBAL MODEL SOMC ELEMENT PACKAGE POWER RATING P70°C W P70°C W 14 16 20 0.08 1.05 1.20 1.52 0.16 1.125 1.28 1.60 0.08 1.05 1.20 1.52 CIRCUIT LIMITING ELEMENT VOLTAGE MAX. TEMPERATURE COEFFICIENT1) ppm/°C TOL. % 01 03 05 50 100 1, 2, 5 1, 2, 5 1, 2, 5 RESISTANCE RANGE E-SERIES Ω 10R – 1M 24 1)Temperature Range: - 55°C to + 125°C • Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material • Jumper: Zero-Ohm-Resistor on request (100mΩ) • Packaging: according to EIA; see appropriate catalog or web page TECHNICAL SPECIFICATIONS PARAMETER Rated Dissipation at 70°C per Element Limiting Element Voltage 2) Voltage Coefficient Insulation Voltage (1min) Category Temperature Range Insulation Resistance TC Tracking (- 55°C to + 125°C) 2)Rated voltage: UNIT W V ppm/V Vdc/ac peak °C Ω ppm/°C 01 CIRCUIT 0.08 03 CIRCUIT 0.16 50 < 50 200 - 55 / + 150 > 10 10 50 05 CIRCUIT 0.08 PxR GLOBAL PART NUMBER INFORMATION New Global Part Numbering: SOMC16011K00GDC (preferred part numbering format) S GLOBAL MODEL O M C 1 6 0 1 1 K 0 0 G RESISTANCE TOLERANCE VALUE CODE R = Decimal F = ± 1% K = Thousand G = ± 2% M = Million J = ± 5% 10R0 = 10Ω S = Special 680K = 680KΩ 1M00 = 1.0MΩ Historical Part Number example: SOMC1601102G (will continue to be accepted) D C PIN COUNT SCHEMATIC PACKAGING SPECIAL 14 16 20 01 = Bussed 03 = Isolated 00 = Special EJ = Lead Free, Tube EA = Lead Free, Tape & Reel DC = Tin/Lead, Tubel RZ = Tin/Lead, Tape & Reel Blank = Standard (Dash Number) (up to 3 digits) From 1-999 as applicable SOMC SOMC 16 01 102 G D02 HISTORICAL MODEL PIN COUNT SCHEMATIC RESISTANCE VALUE TOLERANCE CODE PACKAGING New Global Part Numbering: SOMC2005500BGRZ (preferred part numbering format) S GLOBAL MODEL O M C PIN COUNT 2 0 0 5 5 0 0 B G RESISTANCE TOLERANCE VALUE CODE SOMC 14 05 = Dual 3 digit F = ± 1% 16 Terminator Impedence code, G = ± 2% 20 followed by J = ± 5% Alpha modifier (see Impedence table Historical Part Number example: SOMC2005820131G (will continue to be accepted) SOMC HISTORICAL MODEL www.vishay.com 38 R SCHEMATIC Z PACKAGING SPECIAL EJ = Lead Free, Tube EA = Lead Free, Tape & Reel DC = Tin/Lead, Tubel RZ = Tin/Lead, Tape & Reel Blank = Standard (Dash Number) (up to 3 digits) From 1-999 as applicable 20 05 810 131 PIN COUNT SCHEMATIC VALUE 1 RESISTANCE VALUE 2 RESISTANCE For technical questions contact: [email protected] G R61 TOLERANCE CODE PACKAGING Document Number: 31508 Revision: 07-Sep-04 SOMC Vishay Dale Thick Film, Dual-in-Line Resistor Networks DIMENSIONS SOLDER PAD DIMENSIONS in inches [millimeters] a b c l p w WAVE 0.64 1.91 5.34 9.53 1.27 9.15 REFLOW 0.64 1.91 5.34 9.53 1.27 9.15 The dimensions shown are for 16 pin part. For parts with different pin numbers use the same pitch and add or substract pads as required. Note: Maximum solder reflow temperature + 255°C Pin 1 DIMENSIONS [in millimeters] PIN NO# B E 16 pin G H 14 pin R S T 9.91 7.62 7.62 6.20 5.59 2.16 2.03 0.914 0.457 1.27 1.14 16 11.18 7.62 8.89 6.20 5.59 2.16 2.03 0.914 0.457 1.27 1.14 20 13.72 7.62 11.43 6.20 5.59 2.16 2.03 0.914 0.457 1.27 1.14 Tol ± 0.254 ± 0.381 ± 0.254 ± 0.381 ± 0.127 ± 0.127 ± 0.127 16 pin ± 0.254 R1 R1 R2 R2 R2 R1 R2 R1 R1 R1 R2 R2 R2 R1 R2 R2 R1 R2 R1 R1 20 pin R1 05 Circuit 03 Circuit 20 pin K 14 R2 Pin 1 14 pin F R1 01 Circuit W R2 CIRCUIT SCHEMATICS L 14 pin Pin 1 IMPEDANCE CODES CODE 500B 750B 800C 990A 101C 111C 121B 121C 131A R1 (Ω) 82 120 130 160 180 180 180 220 220 R2 (Ω) 130 200 210 260 240 270 390 270 330 CODE 141A 181A 191A 221B 281B 381B 501C 102A 202B R1 (Ω) 270 330 330 330 560 560 620 1.5K 3K R2 (Ω) 270 390 470 680 560 1.2K 2.7K 3.3K 6.2K PERFORMANCE TEST Power Conditioning Load Life at 70°C Short Time Overload Thermal Shock Moisure Resistance Resistance to Soldering Heat Low Temperature Operation Vibration Shock Terminal Strength Document Number: 31508 Revision: 07-Sep-04 CONDITIONS OF TEST MIL STD-202 MIL STD-202 MIL STD-202 MIL STD-202 MIL STD-202 MIL STD-202 MIL STD-202 MIL STD-202 MIL STD-202 MIL STD-202 For technical questions contact: [email protected] TEST RESULTS ± 0.5% ± 0.5% ± 0.25% ± 0.5% ± 0.5% ± 0.25% ± 0.25% ± 0.25% ± 0.25% ± 0.25% www.vishay.com 39 DFP Vishay Dale Thick Film Resistor Networks Flat Pack, 11, 12 Schematics FEATURES • 11 and 12 Schematics • 0.065" [1.65 mm] height for high density packaging • Low temperature coefficient (- 55 °C to + 125 °C) ± 100 ppm/°C • Hot solder dipped leads • Highly stable thick film • Wide resistance range • All devices are capable of passing the MIL-STD-202, Method 210, Condition C "Resistance to Soldering Heat" test STANDARD ELECTRICAL SPECIFICATIONS GLOBAL MODEL DFP POWER RATING P25 °C P25 °C ELEMENT PACKAGE W W 0.25 0.65 0.15 0.65 CIRCUIT SCHEMATIC 11 12 LIMITING ELEMENT VOLTAGE MAX. V≅ 75 75 Notes 1. Temperature Range: - 55 °C to + 125 °C 2. ± 1 % and ± 5 % tolerance available TEMPERATURE1) COEFFICIENT ppm/°C STANDARD2) TOLERANCE % RESISTANCE RANGE Ω ± 100 ± 100 2 2 10 - 1M 10 - 1M TEMPERATURE COEFFICIENT TRACKING ppm/°C 50 50 • Consult factory for stocked values TECHNICAL SPECIFICATIONS 11 Schematic 7 or 8 isolated resistors The DFPxx11 provides the user with 7 or 8 nominally equal resistors with each resistor isolated from all others. Commonly used in the following applications: • "Wired OR" Pull-up • Long-line Impedance Balancing • Power Driven Pull-up • LED Current Limiting • Power Gate Pull-up • ECL Output Pull-down • Line Termination • TTL Input Pull-down DFP1411 Pin #1 DFP1611 12 Schematic 13 or 15 resistors with one pin common The DFPxx12 provides the user with a choice of 13 or 15 nominally equal resistors, each connected to a common pin (14 or 16). Commonly used in the following applications: • MOS/ROM Pull-up/Pull-down • TTL Input Pull-down • Open Collector Pull-up • Digital Pulse Squaring • "Wired OR" Pull-up • TTL Unused Gate Pull-up • Power Driven Pull-up • High Speed Parallel Pull-up • • • • • • • • DFP1412 Pin #1 DFP1612 GLOBAL PART NUMBER INFORMATION New Global Part Numbering: DFP14121K00GD05 (preferred part numbering format) D GLOBAL MODEL F P 1 4 1 PIN COUNT SCHEMATIC 14 16 11 = Isolated 12 = Bussed DFP 2 1 K RESISTANCE VALUE R = Decimal K = Thousand M = Million 10R0 = 10 Ω 680K = 680 kΩ 1M00 = 1.0 MΩ 0 0 G TOLERANCE CODE F=±1% G=±2% J=±5% D 0 5 PACKAGING SPECIAL E05 = Lead (Pb)-free, Tube D05 = Tin/Lead, Tube Blank = Standard (Dash Number) (up to 3 digits) From 1-999 as applicable Historical Part Number example: DFP1412102G (will continue to be accepted) DFP 14 12 102 G D05 HISTORICAL MODEL PIN COUNT SCHEMATIC RESISTANCE VALUE TOLERANCE CODE PACKAGING www.vishay.com 40 For technical questions, contact: [email protected] Document Number: 31513 Revision: 08-Sep-04 DFP Thick Film Resistor Networks Flat Pack, 11, 12 Schematics Vishay Dale DIMENSIONS in inches [millimeters] Pin #1 0.250 [6.35] Min. 0.365 [9.27] Min. 0.385 [9.78] Max. 0.050 [1.27] Typ. 0.019 ± 0.006 [0.48 ± 0.15] 0.250 [6.35] Min. 0.005 + 0.004 - 0.002 [0.127 + 0.102 - 0.051] 0.065 [1.65] Max. 0.825 [20.96] Max. 0.265 [6.73] Max. GLOBAL MODEL DFP14 DFP16 DIMENSION A 0.037 ± 0.010 [0.94 ± 0.25] 0.012 ± 0.010 [0.30 ± 0.25] TECHNICAL SPECIFICATIONS PARAMETER MECHANICAL SPECIFICATIONS UNIT DFP14/16 MΩ > 100 ppm/V < 50 typical VDC 75 Operating Temperature Range °C - 55 to + 125 Storage Temperature Range °C - 55 to + 150 Isolation Resistance 11 Schematic Voltage Coefficient of Resistance Maximum Operating Voltage Model number, schematic number, value tolerance, pin 1 indicator, date code. Marking Resistance Permanency testing per MIL-STD-202 to Solvents Method 215. Solderability Terminals Per MIL-STD-202, Method 208E. Per MIL-STD-1276 DFPxx11, DFPxx12 = Type G (hot solder dipped). Hot solder dipped leads supplied as standard finish. Body Epoxy filled ceramic sandwich 12 Schematic Power Rating (Watts) 11 Schematic Power Rating (Watts) Marking Package 0.65 0.50 Package 0.65 0.50 Single Resistor 0.25 Single Resistor 0.15 - 55 Derating + 25 + 70 + 125 + 150 Ambient Temperature °C - 55 + 25 Derating + 70 + 125 + 150 Ambient Temperature °C PERFORMANCE MAX. ΔR (Typical Test Lots) TEST CONDITIONS Power Conditioning 1.5 x rated power, applied 1.5 hours “ON” and 0.5 hour “OFF” for 100 hours ± 4 hours at + 25 °C ambient temperature ± 0.50 % ΔR 5 cycles between - 65 °C and + 125 °C 2.5 x rated working voltage, 5 seconds 45 minutes at full rated working voltage at - 65 °C 240 hours with humidity ranging from 80 % RH to 98 % RH Leads immersed in + 260 ° ΔC solder to within 1/16" of body for 10 seconds Total of 18 shocks at 100 g's 12 hours at maximum of 20 g's between 10 and 2000 Hz 1000 hours at + 70 °C, rated power applied 1.5 hours “ON”, 0.5 hour “OFF” for full 1000 hour period. Derated according to the curve. ± 0.50 % ΔR ± 0.25 % ΔR ± 0.25 % ΔR ± 0.50 % ΔR ± 0.25 % ΔR ± 0.25 % ΔR ± 0.25 % ΔR 1.5 pound pull for 30 seconds 10 000 Megohm (minimum) ± 0.25 % ΔR - Thermal Shock Short Time Overload Low Temperature Operation Moisture Resistance Resistance to Soldering Heat Shock Vibration Load Life Terminal Strength Insulation Resistance Dielectric Withstanding Voltage Document Number: 31513 Revision: 08-Sep-04 No evidence of arcing or damage (200 V RMS for 1 minute) For technical questions, contact: [email protected] ± 0.50 % ΔR - www.vishay.com 41 www.vishay.com 42 Through-Hole Resistor Networks SIL, DIL Configurations • Isolated, Bussed or TTL-Terminator Circuits • High Packaging Density Model Numbers MDP-01,03,05 ....44 MDP-45,46 .........48 CSC ....................50 MSP....................54 CS201 ................58 CS206 ................60 MDRC.................62 MDP 01, 03, 05 Vishay Dale Thick Film Resistor Networks, Dual-In-Line, Molded DIP, 01, 03, 05 Schematics FEATURES • 0.160" [4.06mm] maximum seated height and rugged, molded case construction. • Highly stable thick film • Low temperature coefficient (- 55°C to + 125°C) ± 100ppm/°C • Reduces total assembly costs • Compatible with automatic inserting equipment • Wide resistance range • Uniform performance characteristics • Available in tube pack STANDARD ELECTRICAL SPECIFICATIONS GLOBAL MODEL/ NO. OF PINS SCHEMATIC RESISTOR RESISTANCE POWER RATING RANGE Max. @ 70°C* W Ω STANDARD TOLERANCE % TEMPERATURE COEFFICIENT (- 55°C to + 125°C) ppm/°C TCR TRACKING** (- 55°C to + 125°C) ppm/°C WEIGHT g MDP 14 01 03 05 0.125 0.250 0.125 10 - 2.2M ± 2 (± 1, ± 5)*** 10 - 2.2M Consult factory ± 100 ± 50 ± 50 ± 100 1.3 MDP 16 01 03 05 0.125 0.250 0.125 10 - 2.2M ± 2 (± 1, ± 5)*** 10 - 2.2M Consult factory ± 100 ± 50 ± 50 ± 100 1.5 *For resistor power ratings @ + 25°C see derating curves. **Tighter tracking available. ***± 1% and ± 5% tolerences available on request. GLOBAL PART NUMBER INFORMATION New Global Part Numbering: MDP1403100RGD04 (preferred part numbering format) M GLOBAL MODEL MDP D P PIN COUNT 1 4 0 3 1 0 0 R G D SCHEMATIC RESISTANCE TOLERANCE VALUE CODE 14 = 14 Pin 01 = Bussed R = Decimal F = ± 1% 16 = 16 Pin 03 = Isolated K =Thousand G = ± 2% 00 = Special M = Million J = ± 5% 10R0 = 10Ω S = Special 680K = 680KΩ 1M00 = 1.0MΩ Historical Part Number example: MDP1403101G (will continue to be accepted) 0 4 PACKAGING SPECIAL E04 = Lead Free, Tube D04 = Tin/Lead,Tube Blank = Standard (Dash Number) (up to 3 digits) From 1-999 as applicable MDP 14 03 101 G D04 HISTORICAL MODEL PIN COUNT SCHEMATIC RESISTANCE VALUE TOLERANCE CODE PACKAGING New Global Part Numbering: MDP1405121CGD04 (preferred part numbering format) M GLOBAL MODEL MDP D P PIN COUNT 1 4 0 5 1 2 1 C G RESISTANCE TOLERANCE VALUE CODE 14 = 14 Pin 05 = Dual 3 digit F = ± 1% 16 = 16 Pin Terminator Impedance code G = ± 2% followed by J = ± 5% Alpha modifier (see Impedence codes table) Historical Part Number example: MDP1405221271G (will continue to be accepted) D SCHEMATIC 0 4 PACKAGING SPECIAL E04 = Lead Free, Tube D04 = Tin/Lead,Tube Blank = Standard (Dash Number) (up to 3 digits) From 1-999 as applicable MDP 14 05 221 271 G D04 HISTORICAL MODEL PIN COUNT SCHEMATIC RESISTANCE VALUE 1 RESISTANCE VALUE 2 TOLERANCE CODE PACKAGING www.vishay.com 44 For Technical Questions, contact: [email protected] Document Number: 31511 Revision 10-Sep-04 MDP 01, 03, 05 Thick Film Resistor Networks, DIP, Molded Vishay Dale DIMENSIONS in inches [millimeters] 0.120 ± 0.005 [3.05 ± 0.127] A ± 0.010 [0.254] 0.310 ± 0.010 [7.87 ± 0.254] 0.250 ± 0.005 [6.35 ± 0.127] 0.030 [0.762] Typ. Pin #1 Identification 0.075 ± 0.015 [1.90 ± 0.381] Pin #1 0.130 + 0.015 - 0.010 [3.30 + 0.381 - 0.254] 0.018 ± 0.003 [0.457 ± 0.076] 0.100 ± 0.010 [2.54 ± 0.254] Non-Accumulative Tol. "C" Spaces B ± 0.010 [0.254] 0.050 ± 0.005 [1.27 ± 0.127] 0.010 + 0.005 - 0.002 [0.254 + 0.127 - 0.051] 0.290 Min. 0.320 Nom. 0.360 Max. [7.37 Min. 8.13 Nom. 9.14 Max.] A B C MDP 14 0.750 [19.05] 0.600 [15.24] 6 MDP 16 0.850 [21.59] 0.700 [17.78] 7 GLOBAL MODEL TECHNICAL SPECIFICATIONS PARAMETER UNIT MDP14 MDP16 Package Power Rating (Maximum at + 70°C) W 1.73 1.92 Voltage Coefficient of Resistance Veff < 50ppm typical VAC 200 Insulation Resistance Ω > 10,000M minimum Operating Temperature Range °C - 55 to + 125 Storage Temperature Range: °C - 55 to + 150 Dielectric Strength MECHANICAL SPECIFICATIONS Marking Resistance to Solvents: Permanency testing per MIL-STD-202, Method 215. Solderability: Per MIL-STD-202, Method 208E. Body: Molded epoxy. Terminals: Solder plated leads. Weight: 14 pin = 1.3 grams; 16 pin = 1.5 grams Document Number: 31511 Revision 10-Sep-04 For Technical Questions, contact: [email protected] www.vishay.com 45 MDP 01, 03, 05 Vishay Dale Thick Film Resistor Networks, DIP, Molded IMPEDANCE CODES CODE 500B 750B 800C 990A 101C 111C 121B 121C 131A R1(Ω) R2(Ω) 82 120 130 160 180 180 180 220 220 130 200 210 260 240 270 390 270 330 CODE 141A 181A 191A 221B 281B 381B 501C 102A 202B R1(Ω) R2(Ω) 270 330 330 330 560 560 620 1.5K 3K 270 390 470 680 560 1.2K 2.7K 3.3K 6.2K CIRCUIT APPLICATIONS 01 Schematic 13 and 15 resistors with one pin common The MDPXX01 circuit provides a choice of 13 and 15 nominally equal resistors, each connected between a common pin (14 and 16) and a discrete PC board pin. Commonly used in the following applications: • MOS/ROM Pull-up/Pull-down • TTL Input Pull-down • Open Collector Pull-up • Digital Pulse Squaring • "Wired OR" Pull-up • TTL Unused Gate Pull-up • Power Driven Pull-up • High Speed Parallel Pull-up • • • • • • • • MDP1401 Pin #1 MDP1601 03 Schematic 7 and 8 isolated resistors The MDPXX03 provides a choice of 7 and 8 nominally equal resistors, each resistor isolated from all others and wired directly across. Commonly used in the following applications: • "Wired OR" Pull-up • Long-line Impedance Balancing • Power Driven Pull-up • LED Current Limiting • Powergate Pull-up • ECL Output Pull-down • Line Termination • TTL Input Pull-down MDP1403 Pin #1 MDP1603 05 Schematic R1 R1 R2 R1 R2 Pin #1 R1 R2 R1 R2 R1 R2 R1 R2 R1 R2 R1 R2 R1 R2 R1 R2 R2 R1 R2 TTL dual-line terminator; pulse squaring R1 R2 R1 R2 The MDPXX05 circuit contains 12 and 14 series pair of resistors. Each series pair is connected between ground and a common line. The junction of these resistor pairs is connected to the input terminals. The 05 circuits are designed for TTL dual-line termination and pulse squaring. MDP1405, MDP1605 Standard E-24 resistance values stocked. Consult factory www.vishay.com 46 For Technical Questions, contact: [email protected] Document Number: 31511 Revision 10-Sep-04 MDP 01, 03, 05 Power Rating (Watts) Thick Film Resistor Networks, DIP, Molded 3.00 Vishay Dale 16 Pin Package 14 Pin Package 2.70 Single Resistor 03 0.380 0.190 01 and 05 - 50 + 25 Derating + 70 + 125 + 150 Ambient Temperature °C PERFORMANCE MAX. ∆R (Typical Test Lots) TEST CONDITIONS Power Conditioning 1.5 rated power, applied 1.5 hours “ON” and 0.5 hour “OFF” for 100 hours ± 4 hours at + 25°C ambient temperature ± 0.50% ∆R Thermal Shock 5 cycles between - 65°C and + 125°C ± 0.50% ∆R Short Time Overload 2.5 x rated working voltage 5 seconds ± 0.25% ∆R Low Temperature Operation 45 minutes at full rated working voltage at - 65°C ± 0.25% ∆R Moisture Resistance 240 hours with humidity ranging from 80% RH to 98% RH ± 0.50% ∆R Resistance to Soldering Heat Leads immersed in + 350°C solder to within 1/16" of device body for 3 seconds ± 0.25% ∆R Shock Total of 18 shocks at 100 G's ± 0.25% ∆R Vibration 12 hours at maximum of 20 G's between 10 and 2,000 Hz ± 0.25% ∆R Load Life 1000 hours at + 70°C, rated power applied 1.5 hours “ON, 0.5 hour “OFF” for full 1000 hour period. Derated according to the curve. ± 1.00% ∆R Terminal Strength 4.5 pound pull for 30 seconds ± 0.25% ∆R Insulation Resistance 10,000 Megohm (minimum) — Dielectric Withstanding Voltage No evidence of arcing or damage (200 VRMS for 1 minute) — Document Number: 31511 Revision 10-Sep-04 For Technical Questions, contact: [email protected] www.vishay.com 47 MDP 45, 46 Vishay Dale Thick Film Resistor Networks, Dual-In-Line, Molded DIP FEATURES • 0.190" [4.83mm] maximum seated height • Rugged, molded case construction • Low temperature coefficient (- 55°C to + 125°C), MDP 1645: ± 100ppm/°C, MDP 1646: ± 250ppm/°C • Compatible with automatic insertion equipment • Highly stable thick film • Reduces PC board space and reduces total assembly costs • Available in tube pack STANDARD ELECTRICAL SPECIFICATIONS GLOBAL MODEL/ PIN NO. RESISTOR POWER RATING Max. @ 70°C W PACKAGE POWER RATING Max. @ 70°C W STANDARD TOLERANCE TEMPERATURE COEFFICIENT (- 55°C to + 125°C) ppm/°C TEMPERATURE COEFFICIENT TRACKING ppm/°C WEIGHT MDP1645 0.125 2.0 2 ± 100 Typical ± 150 1.5 MDP1646 0.125 2.0 5 ± 250 Typical ± 150 1.5 ±% g CIRCUIT APPLICATIONS MDP1645 Schematic TTL INPUTS VCC 16 TTL to ECL translator 180Ω The MDP1645 network consists of 18 resistors of 3 different values, internally divided into six (6) identical three (3) resistor sections for TTL to ECL translation. 270Ω 820Ω 1 VCC VEE OUTPUTS TO ECL MDP1646 Schematic 16 9 330Ω SCSI-BUS signal terminator R1 The MDP1646 network consists of 21 resistors of 2 different values, internally divided into seven (7) identical three (3) resistor sections for SCSI-BUS terminator applications. 150Ω R2 R1 330Ω 1 8 GLOBAL PART NUMBER INFORMATION New Global Part Numbering: MDP1646D04 (preferred part numbering format) M D P 1 6 4 6 D 0 4 GLOBAL MODEL PIN COUNT SCHEMATIC PACKAGING MDP 16 45 = TTL/ECL Translator 46 = Signal Terminator E04 = Lead Free, Tube D04 = Tin/Lead, Tube SPECIAL Blank = Standard (Dash Number) (up to 3 digits) From 1-999 as applicable Historical Part Number: MDP1646 (will continue to be accepted) MDP 16 HISTORICAL MODEL www.vishay.com 48 PIN COUNT 46 SCHEMATIC For Technical Questions, contact: [email protected] D04 PACKAGING Document Number: 31512 Revision 08-Sep-04 MDP 45, 46 Vishay Dale Thick Film Resistor Networks, Dual-In-Line, Molded DIP DIMENSIONS in inches [millimeters] 0.850 ± 0.010 [21.59 ± 0.254] 0.250 ± 0.005 [6.35 ± 0.127] 0.030 [0.762] Typ. Pin 1 Identification 0.075 ± 0.015 [1.91 ± 0.381] Pin 1 0.100 ± 0.010 [2.54 ± 0.254] Non-Accumulative Tol. 7 Spaces Power Rating (Watts) 0.310 ± 0.010 [7.87 ± 0.254] 0.120 ± 0.005 [3.05 ± 0.127] 0.700 ± 0.010 [17.78 ± 0.254] 0.010 + 0.005 - 0.002 [0.254 + 0.127] - 0.051] 0.130 + 0.015 - 0.010 [3.30 + 0.381] - 0.254] 0.018 ± 0.003 [0.457 ± 0.076] 0.290 [7.37] Min. 0.320 [8.13] Nom. 0.360 [9.14] Max. 0.050 ± 0.005 [1.27 ± 0.127] TECHNICAL SPECIFICATIONS 2.00 MDP1645 Package & MDP1646 Package PARAMETER UNIT MDP Series Maximum Operating Voltage VDC 100 Voltage Coefficient of Resistance (Typical) Veff < 50 ppm/°C Operating Temperature Range °C - 55 to + 125 Storage Temperature Range °C - 55 to + 150 1.00 MECHANICAL SPECIFICATIONS .125 Marking Resistance to Solvents: Permanency testing per MILSTD-202, Method 215. Solderability: Per MIL-STD-202, Method 208E. Terminals: Copper alloy, solder plated. Body: Molded epoxy. Weight: 1.5 grams. Single Resistor - 50 + 25 Derating + 70 + 125 + 150 Ambient Temperature °C PERFORMANCE MAX. ∆R (Typical Test Lots) TEST CONDITIONS Thermal Shock 5 cycles between - 65°C and + 125°C ± 0.50% ∆R Short Time Overload 2.5 x rated working voltage 5 seconds ± 0.25% ∆R Low Temperature Operation 45 minutes at full rated working voltage at - 65°C ± 0.25% ∆R Moisture Resistance 240 hours with humidity ranging from 80% RH to 98% RH ± 0.50% ∆R Resistance to Soldering Heat Leads immersed in + 260°C solder to within 1/16" of body for 10 seconds ± 0.25% ∆R Shock Total of 18 shocks at 100 g's ± 0.25% ∆R Vibration 12 hours at maximum of 20 g's between 10 and 2,000 Hz ± 0.25% ∆R Load Life 1,000 hours at + 70°C, rated power applied 1.5 hours “ON”, 0.5 hour “OFF” for full 1000 hour period. Derated according to the curve. ± 0.50% ∆R Terminal Strength 4 1/2 pound pull for 30 seconds ± 0.25% ∆R Insulation Resistance 10,000 Megohm (minimum) — Dielectric Withstanding Voltage No evidence of arcing or damage (200 V RMS for 1 minute) — Document Number: 31512 Revision 08-Sep-04 For Technical Questions, contact: [email protected] www.vishay.com 49 CSC Vishay Dale Thick Film Resistor Networks Single-In-Line, Coated SIP 01, 03, 05 Schematics FEATURES • • • • • • • • 0.195" [4.95mm] "A", 0.250" [6.35mm] "B" "A" profile standard in 4 thru 12 pins Highly stable thick film Low temperature coefficient (- 55°C to + 125°C) ± 100ppm/°C Reduces total assembly costs Resistor elements protected by tough epoxy conformal coating Wide resistance range Available in bag pack or tube pack STANDARD ELECTRICAL SPECIFICATIONS GLOBAL MODEL/ SCHEMATIC CSCxxx01 PROFILE RESISTOR RESISTANCE STANDARD TEMPERATURE TCR POWER RATING RANGE TOLERANCE COEFFICIENT TRACKING Max. @ 70°C* Ω % (- 55°C to + 125°C) (- 55°C to + 125°C) A 0.20 W 10 - 2.2M ± 2 (1%*) ± 100ppm/°C ± 50ppm/°C B 0.25 W CSCxxx03 A 0.30 W 10 - 2.2M ± 2 (1%*) ± 100ppm/°C ± 50ppm/°C B 0.40 W CSCxxx05 A 0.20 W 10 - 2.2M ± 2 (1%*) ± 100ppm/°C ± 150ppm/°C B 0.25 W * For resistor power ratings @ + 25°C see derating curves. • See derating curves for Package Power Rating. Higher power rated “C” Profile available. * Contact factory for 1% OPERATING VOLTAGE VDC Max. 100 100 100 TECHNICAL SPECIFICATIONS PARAMETER Voltage Coefficient of Resistance Dielectric Strength Isolation Resistance (03 Schematic) Operating Temperature Range UNIT Veff VAC Ω °C CSC Series < 50ppm typical 200 > 100M - 55 to + 125 GLOBAL PART NUMBER INFORMATION New Global Part Numbering: CSC08A03100RGDA (preferred part numbering format) C GLOBAL MODEL CSC S PIN COUNT C 0 8 PACKAGE HEIGHT A 0 3 1 0 0 R G D SCHEMATIC RESISTANCE TOLERANCE VALUE CODE 04 = 4 Pin A = “A” Profile 01 = Bussed R = Decimal F = ± 1% 08 = 8 Pin B = “B” Profile 03 = Isolated K = Thousand G = ± 2% 12 = 12 Pin 00 = Special M = Million J = ± 5% 10R0 = 10Ω S = Special 680K = 680KΩ 1M00 = 1.0MΩ Historical Part Number example: CSC08A03101G (will continue to be accepted) A PACKAGING SPECIAL EJ = Lead Free, Tube EK = Lead Free, Bulk DA = Tin/Lead, Tube PA = Tin/Lead, Bulk Blank = Standard (Dash Number) (up to 3 digits) From 1-999 as applicable CSC 08 A 03 101 G D03 HISTORICAL MODEL PIN COUNT PACKAGE HEIGHT SCHEMATIC RESISTANCE VALUE TOLERANCE CODE PACKAGING New Global Part Numbering: CSC08A05131AGPA (preferred part numbering format) C GLOBAL MODEL CSC S PIN COUNT C 0 8 PACKAGE HEIGHT A 0 5 1 3 1 A G SCHEMATIC RESISTANCE TOLERANCE VALUE CODE 04 = 4 Pin A = “A” Profile 05 = Dual 3 digit F = ± 1% 08 = 8 Pin B = “B” Profile Terminator Impedence code, G = ± 2% 12 = 12 Pin followed by J = ± 5% Alpha modifier (see Impedence codes table) Historical Part Number example: CSC08A05221331G (will continue to be accepted) P A PACKAGING SPECIAL EJ = Lead Free, Tube EK = Lead Free, Bulk DA = Tin/Lead, Tube PA = Tin/Lead, Bulk Blank = Standard (Dash Number) (up to 3 digits) From 1-999 as applicable CSC 08 A 05 221 331 G P03 HISTORICAL MODEL PIN COUNT PACKAGE HEIGHT SCHEMATIC RESISTANCE VALUE 1 RESISTANCE VALUE 2 TOLERANCE CODE PACKAGING www.vishay.com 50 For Technical Questions, contact: [email protected] Document Number: 31509 Revision 08-Sep-04 CSC Thick Film Resistor Networks, Single-In-Line, Coated SIP Vishay Dale DIMENSIONS in inches [millimeters] A Max. 0.098 [2.49] Max. C Max. Pin #1 0.130 ± 0.010 [3.30 ± 0.254] 0.045 [1.14] 0.032 [0.813] 0.050 [1.27] Max. 0.018 ± 0.003 [0.457 ± 0.076] 0.100 ± 0.010 [2.54 ± 0.254] Non-Accumulative B 01 Schematic 1 2 3 n-1 2 3 4 n-1 n 05 Schematic R2 R1 1 2 3 GLOBAL MODEL NUMBER OF RESISTORS CSC04 CSC05 A (Maximum) B 3 0.390 [9.90] 0.300 [7.62] 4 0.490 [12.45] 0.400 [10.16] CSC06 5 0.590 [14.99] 0.500 [12.70] CSC07 6 0.690 [17.53] 0.600 [15.24] CSC08 7 0.790 [20.07] 0.700 [17.78] CSC09 8 0.890 [22.61] 0.800 [20.32] CSC10 9 0.990 [25.15] 0.900 [22.86] CSC11* 10 1.09 [27.69] 1.00 [25.40] CSC12* 11 1.19 [30.23] 1.100 [27.94] GLOBAL MODEL NUMBER OF RESISTORS A (Maximum) B C (Maximum) CSC04 2 0.390 [9.90] 0.300 [7.62] "A" Profile = 0.195 [4.95] CSC06 3 0.590 [14.99] 0.500 [12.70] CSC08 4 0.790 [20.07] 0.700 [17.78] CSC10 5 0.990 [25.15] 0.900 [22.86] CSC12* 6 NUMBER OF RESISTORS 1.19 [30.23] 1.100 [27.94] GLOBAL MODEL A (Maximum) B C (Maximum) CSC04 4 0.390 [9.90] 0.300 [7.62] "A" Profile = 0.195 [4.95] CSC05 6 0.490 [12.45] 0.400 [10.16] "B" Profile = 0.250 [6.35] CSC06 8 0.590 [14.99] 0.500 [12.70] CSC07 10 0.690 [17.53] 0.600 [15.24] CSC08 12 0.790 [20.07] 0.700 [17.78] CSC09 14 0.890 [22.61] 0.800 [20.32] CSC10 16 0.990 [25.15] 0.900 [22.86] CSC11* 18 1.09 [27.69] 1.00 [25.40] CSC12* 20 1.19 [30.23] 1.100 [27.94] n 03 Schematic 1 n-1 0.012 ± 0.003 [0.305 ± 0.076] (Leads are Along Centerline of Body) n C (Maximum) "A" Profile = 0.195 [4.95] "B" Profile = 0.250 [6.35] "B" Profile = 0.250 [6.35] * "B" Profile only. MECHANICAL SPECIFICATIONS STOCKED RESISTANCE VALUES IN OHMS (“G” TOLERANCE) Marking Resistance to Solvents: Permanency testing per MIL-STD202, Method 215. Solderability: Per MIL-STD-202, Method 208E, RMA flux. Standard E-24 resistance values stocked. Consult factory. Body: High alumina, epoxy coated. Terminals: Solder plated leads. Many dual terminator resistance values stocked. Consult factory Document Number: 31509 Revision 08-Sep-04 For Technical Questions, contact: [email protected] www.vishay.com 51 CSC Vishay Dale Thick Film Resistor Networks, Single-In-Line, Coated SIP IMPEDANCE CODES CODE 500B 750B 800C 990A 101C 111C 121B 121C 131A R1(Ω) R2(Ω) 82 120 130 160 180 180 180 220 220 130 200 210 260 240 270 390 270 330 CODE 141A 181A 191A 221B 281B 381B 501C 102A 202B R1(Ω) R2(Ω) 270 330 330 330 560 560 620 1.5K 3K 270 390 470 680 560 1.2K 2.7K 3.3K 6.2K "A" Profile Power Rating (Watts) "A" PROFILE + 70°C PACKAGE RATINGS CSC12A 1.5 watts CSC11A 1.37 watts CSC10A 1.25 watts CSC09A 1.12 watts CSC08A 1.00 watts CSC07A 0.87 watts CSC06A 0.75 watts CSC05A 0.62 watts CSC04A 0.40 watts CSC10A Package 1.90 CSC08A Package 1.50 CSC06A Package 1.15 Single Resistor 03 Schematic 0.45 0.30 01 and 05 Schematics - 50 Derating + 25 + 70 + 125 + 150 Ambient Temperature °C Power Rating (Watts) "B" Profile "B" PROFILE + 70°C PACKAGE RATINGS 2.50 2.00 1.50 CSC12B 1.90 watts CSC10B Package CSC11B 1.75 watts CSC08B Package CSC10B 1.60 watts CSC06B Package CSC09B 1.45 watts CSC08B 1.30 watts CSC07B 1.15 watts CSC06B 1.00 watts CSC05B 0.80 watts CSC04B 0.60 watts Single Resistor 03 Schematic 0.60 0.38 01 and 05 Schematics - 50 Derating www.vishay.com 52 + 25 + 70 + 125 + 150 Ambient Temperature °C For Technical Questions, contact: [email protected] Document Number: 31509 Revision 08-Sep-04 CSC Thick Film Resistor Networks, Single-In-Line, Coated SIP Vishay Dale CIRCUIT APPLICATIONS "A" Profile = 3, 5, 7, 9 and 11 resistors with one pin common 01 Schematic 1 2 3 n-1 The CSCxxx01 single-in-line resistor networks provide the user with nominally equal resistors, each connected to a common pin (Pin No. 1). Commonly used in the following applications: • "Wired OR" Pull-up • Open Collector Pull-up • Power Gate Pull-up • TTL Input Pull-down • MOS/ROM Pull-up/Pull-down • TTL Unused Gate Pull-up * "B" Profile available. Odd pin available in 5, 7, 9, and 11. n 03 Schematic "A" Profile = 2 through 6 isolated resistors The CSCxxx03 single-in-line resistor networks provide the user with nominally equal resistors. Each resistor is isolated from all others. Commonly used in the following applications: • "Wired OR" Pull-up • Long-Line Impedance Balancing • Power Driven Pull-up • LED Current Limiting • Power Gate Pull-up • ECL Output Pull-down 1 2 3 4 n-1 n • Line Termination * "B" Profile available. 05 Schematic Pulse squaring and TTL dual-line terminators R2 The CSCxxx05 circuits contain series pairs of resistors. Each series pair is connected between two common lines. The junction of these resistor pairs is connected to the input terminals. The 05 circuits are designed for TTL dualline termination and pulse squaring. R1 1 2 • TTL Input Pull-down 3 n-1 n * "B" Profile available. Odd pin available in 5, 7, 9 and 11. PERFORMANCE MAX. ∆R (Typical Test Lots) TEST CONDITIONS Thermal Shock 5 cycles between - 65°C and + 125°C ± 0.50% ∆R Short Time Overload 2.5 x rated working voltage, 5 seconds ± 0.25% ∆R Low Temperature Operation 45 minutes at full rated working voltage at - 65°C ± 0.25% ∆R Moisture Resistance 240 hours with humidity ranging from 80% RH to 98% RH ± 1.00% ∆R Resistance to Soldering Heat Leads immersed in + 350°C solder to within 1/16" of body for 3 seconds ± 0.25% ∆R Shock Total of 18 shocks at 100 G's ± 0.25% ∆R Vibration 12 hours at maximum of 20 G's between 10 and 2,000 Hz ± 0.25% ∆R Load Life 1,000 hours at + 70°C, rated power applied 1.5 hours “ON”, 0.5 hour “OFF” for full 1000 hour period. Derated according to the curve. ± 1.00% ∆R Terminal Strength 4.5 pound pull for 30 seconds ± 0.25% ∆R Insulation Resistance 10,000 Megohm (minimum) — Dielectric Withstanding Voltage No evidence of arcing or damage (200 V RMS for 1 minute) — Document Number: 31509 Revision 08-Sep-04 For Technical Questions, contact: [email protected] www.vishay.com 53 MSP Vishay Dale Thick Film Resistor Networks Single-In-Line, Molded SIP; 01, 03, 05 Schematics 6, 8, 9 or 10 Pin "A" Profile and 6, 8 or 10 Pin "C" Profile FEATURES • 0.195" [4.95mm] "A" or 0.350" [8.89mm] "C" maximum seated height • Highly stable thick film • Low temperature coefficient (- 55°C to + 125°C) ± 100ppm/°C • Rugged, molded case construction • Reduces total assembly costs • Compatible with automatic insertion equipment and reduces PC board space • Wide resistance range • Available in tube pack or side-by-side pack STANDARD ELECTRICAL SPECIFICATIONS GLOBAL MODEL/ SCHEMATIC PROFILE RESISTOR POWER RATING Max. @ 70°C* W RESISTANCE RANGE STANDARD TOLERANCE Ω % TEMPERATURE TCR COEFFICIENT TRACKING* (- 55°C to + 125°C) (- 55°C to + 125°C) ppm/°C ppm/°C OPERATING VOLTAGE Max. VDC MSPxxx01 A C 0.20 0.25 10 - 2.2M ± 2 Standard (1, 5)** ± 100 ± 50ppm/°C 100 MSPxxx03 A C 0.30 0.40 10 - 2.2M ± 2 Standard (1, 5)** ± 100 ± 50ppm/°C 100 MSPxxx05 A C 0.20 0.25 10 - 2.2M ± 2 Standard (± 5%)** ± 100 ± 150ppm/°C 100 * Tighter tracking available ** Tolerances in brackets available on request GLOBAL PART NUMBER INFORMATION New Global Part Numbering: MSP06A031K00GDA (preferred part numbering format) M GLOBAL MODEL MSP S P 0 6 A 0 3 1 K 0 0 G D PIN COUNT PACKAGE HEIGHT SCHEMATIC RESISTANCE TOLERANCE VALUE CODE 06 = 6 Pin A = “A” Profile 01 = Bussed R = Decimal F = ± 1% 08 = 8 Pin C = “C” Profile 03 =Isolated K = Thousand G = ± 2% 09 = 9 Pin 00 = Special M = Million J = ± 5% 10 = 10 Pin 10R0 = 10Ω S = Special 680K = 680KΩ 1M00 = 1.0MΩ Historical Part Number example: MSP06A03102G (will continue to be accepted) A PACKAGING SPECIAL EJ = Lead Free, Tube Blank = Standard DA = Tin/Lead, Tube (Dash Number) (up to 3 digits) From 1-999 as applicable MSP 06 A 03 102 G DO3 HISTORICAL MODEL PIN COUNT PACKAGE HEIGHT SCHEMATIC RESISTANCE VALUE TOLERANCE CODE PACKAGING New Global Part Numbering: MSP08C05131AGDA (preferred part numbering format) M GLOBAL MODEL MSP S P 0 8 C 0 5 1 3 1 A G D PIN COUNT PACKAGE HEIGHT SCHEMATIC RESISTANCE TOLERANCE VALUE CODE 06 = 6 Pin A = “A” Profile 05 = Dual 3 digit F = ± 1% 08 = 8 Pin C = “C” Profile Terminator Impedence code, G = ± 2% 09 = 9 Pin followed by J = ± 5% 10 = 10 Pin Alpha modifier (see Impedence codes table) Historical Part Number example: MSP08C05221331G (will continue to be accepted) A PACKAGING SPECIAL EJ = Lead Free, Tube Blank = Standard DA = Tin/Lead, Tube (Dash Number) (up to 3 digits) From 1-999 as applicable MSP 08 C 05 221 331 G DO3 HISTORICAL MODEL PIN COUNT PACKAGE HEIGHT SCHEMATIC RESISTANCE VALUE 1 RESISTANCE VALUE 2 TOLERANCE PACKAGING www.vishay.com 54 For Technical Questions, contact: [email protected] Document Number: 31510 Revision 09-Sep-04 MSP Vishay Dale Thick Film Resistor Networks, Single-In-Line, Molded SIP DIMENSIONS in inches [millimeters] A Max. 0.090 [2.29] Max. PIN #1 0.015 [0.381] Min. 0.040 ± 0.010 [1.02 ± 0.254] D Max. 0.016 ± 0.003 [0.406 ± 0.076] 0.100 ± 0.010 [2.54 ± 0.254] Non-Accumulative B C Equal Space 0.135 + 0.015 - 0.010 [3.43 + 0.381 - 0.254] 0.012 ± 0.003 [0.305 ± 0.076] A (Max.) B C MSP06 0.590 [14.99] 0.500 [12.70] 5 MSP08 0.790 [20.07] 0.700 [17.78] 7 MSP10 0.990 [25.15] 0.900 [22.86] 9 MSP09 0.890 [22.61] 0.800 [20.32] 8 GLOBAL MODEL D (Max.) MSPxxA = 0.195 [4.95] MSPxxC = 0.350 [8.89] 0.195 [4.95] ONLY TECHNICAL SPECIFICATIONS PARAMETER UNIT MSP SERIES Package Power Rating See Derating Curves (Maximum at + 25°C and + 70°C Voltage Coefficient of Resistance Veff < 50ppm typical VAC 200 Isolation Resistance (03 Schematic) Ω > 100M Operating Temperature Range °C - 55 to + 125 Storage Temperature Range °C - 55 to + 150 Dielectric Strength MECHANICAL SPECIFICATIONS Marking Resistance to Solvents: Permanency testing per MIL-STD-202, Method 215. Solderability: Per MIL-STD-202, Method 208E, RMA flux. Body: Molded epoxy. Terminals: Copper alloy, solder plated. Weight: MSP06A = 0.4 gram MSP08A = 0.5 gram MSP09A = 0.55 gram MSP10A = 0.6 gram Document Number: 31510 Revision 09-Sep-04 MSP06C = 0.7 gram MSP08C = 0.9 gram MSP10C = 1.1 gram For Technical Questions, contact: [email protected] www.vishay.com 55 MSP Vishay Dale Thick Film Resistor Networks, Single-In-Line, Molded SIP IMPEDANCE CODES CODE 500B 750B 800C 990A 101C 111C 121B 121C 131A R1(Ω) R2(Ω) 82 120 130 160 180 180 180 220 220 130 200 210 260 240 270 390 270 330 CODE 141A 181A 191A 221B 281B 381B 501C 102A 202B R1(Ω) R2(Ω) 270 330 330 330 560 560 620 1.5K 3K 270 390 470 680 560 1.2K 2.7K 3.3K 6.2K CIRCUIT APPLICATIONS 5, 7, 8* or 9 resistors with one pin common 01 Schematic 1 The MSPxxx01 circuit contains 5, 7, 8* or 9 nominally equal resistors, each connected between a common pin (Pin No. 1) and a discrete PC board pin. Commonly used in the following applications: • "Wired OR" Pull-up • MOS/ROM Pull-up/Pull-down • Power Gate Pull-up • Open Collector Pull-up • TTL Input Pull-down • TTL Unused Gate Pull-up 2 3 n-1 n * Available in "A" Profile only Standard E-24 resistance values stocked. Consult factory. 03 Schematic 3, 4 or 5 isolated resistors The MSPxxx03 circuit contains 3, 4 or 5 resistors of nominally equal value in a compact package. Each resistor is connected to two discrete PC pins. 1 2 3 4 n-1 n Standard E-24 resistance values stocked. Consult factory. Pulse squaring and TTL dual-line terminators 05 Schematic The MSPxxx05 circuits contain 4, 6, 7* or 8 series pair of resistors. Each series pair is connected between two common lines. The junction of these resistor pairs is connected to the input terminals. R2 The 05 circuits are designed for TTL dual-line termination and pulse squaring. R1 * Available in "A" Profile only Many dual terminator resistance values stocked. Consult factory. 1 www.vishay.com 56 2 3 n-1 n For Technical Questions, contact: [email protected] Document Number: 31510 Revision 09-Sep-04 MSP Vishay Dale Thick Film Resistor Networks, Single-In-Line, Molded SIP 1.90 1.50 1.15 "C" Profile Power Rating (Watts) Power Rating (Watts) "A" Profile MSP10A Package MSP08A Package 3.00 MSP10C Package 2.50 MSP08C Package 2.00 MSP06A Package MSP06C Package 1.50 0.45 Single Resistor 03 0.30 Single Resistor 03 0.60 01 and 05 01 and 05 0.38 - 50 Derating + 25 + 70 + 125 Ambient Temperature °C "A" PROFILE + 70°C PACKAGE RATINGS MSP10A 1.25 watts MSP09A 1.12 watts MSP08A 1.00 watts MSP06A 0.75 watts - 50 + 150 Derating + 25 + 70 + 125 + 150 Ambient Temperature °C "C" PROFILE + 70°C PACKAGE RATINGS MSP10C 1.60 watts MSP08C 1.30 watts MSP06C 1.00 watts Higher power ratings available. Contact factory. PERFORMANCE TEST CONDITIONS Power Conditioning 1.5 x rated power, applied 1.5 hours “ON” and 0.5 hour “OFF” for 100 hours ± 4 hours at + 25°C ambient temperature ± 0.50% ∆R Thermal Shock 5 cycles between - 65°C and + 125°C ± 0.50% ∆R Short Time Overload 2.5 x rated working voltage 5 seconds ± 0.25% ∆R Low Temperature Operation 45 minutes at full rated working voltage at - 65°C ± 0.25% ∆R Moisture Resistance 240 hours with humidity ranging from 80% RH to 98% RH ± 0.50% ∆R Resistance to Soldering Heat Leads immersed in + 260°C solder to within 1/16" of device body for 10 seconds ± 0.25% ∆R Shock Total of 18 shocks at 100 G's ± 0.25% ∆R Vibration 12 hours at maximum of 20 G's between 10 and 2,000 HZ ± 0.25% ∆R Load Life 1000 hours at + 70°C, rated power applied 1.5 hours “ON”, 0.5 hour “OFF” for full 1,000 hour period. Derated according to the curve. ± 1.00% ∆R Terminal Strength 4.5 pound pull for 30 seconds ± 0.25% ∆R Insulation Resistance 10,000 Megohm (minimum) Dielectric Withstanding Voltage Document Number: 31510 Revision 09-Sep-04 MAX. ∆R (Typical Test Lots) — — For Technical Questions, contact: [email protected] www.vishay.com 57 CS201 Vishay Dale Capacitor Networks, Single-In-Line, Coated SIP, "D" Profile FEATURES • X7R and COG capacitors available • Multiple isolated capacitors • Multiple capacitors, common ground • Custom design capability • "D" 0.300" [7.62mm] package height (maximum) STANDARD ELECTRICAL SPECIFICATIONS VISHAY DALE MODEL PROFILE SCHEMATIC CAPACITANCE RANGE COG* X7R CAPACITANCE TOLERANCE (-55°C to + 125°C) % CAPACITOR VOLTAGE @ 85°C VDC CS201 D 1 33pF-3900pF 470pF-0.1µF ± 10 (K), ± 20 (M) 50 (5) CS201 D 3 33pF-3900pF 470pF-0.1µF ± 10 (K), ± 20 (M) 50 (5) CS201 D 4 33pF-3900pF 470pF-0.1µF ± 10 (K), ± 20 (M) 50 (5) *COG capacitors may be substituted for X7R capacitors TECHNICAL SPECIFICATIONS MECHANICAL SPECIFICATIONS PARAMETER Marking Resistance to Solvents: UNIT COG Temperature Coefficient ppm/°C or % (- 55°C to +125°C) Dissipation Factor (maximum) CS201 X7R ± 30 ± 15% ppm/°C ±% 0.15 2.5 Permanency testing per MIL-STD202, Method 215. Solderability: Per MIL-STD-202, Method 208E. Body: High alumina, epoxy coated. (Flammability UL94 V-0.) Terminals: Phosphorus-bronze, solder plated. Marking: Pin #1 identifier, DALE or D, Part number(abbreviated as space allows), Date code. GLOBAL PART NUMBER INFORMATION New Global Part Numbering: 20108D1C103K5P (preferred part numbering format) 2 0 1 0 8 D 1 C 1 0 3 K 5 P GLOBAL PIN PACKAGE SCHEMATIC CHARACTERISTIC CAPACITANCE TOLERANCE VOLTAGE PACKAGING SPECIAL MODEL COUNT HEIGHT VALUE 210 = CS201 04 = 4 Pin D = “D” 1 C = COG (in picofarads) K = ±10% 5 = 50V E = Lead Free, Bulk Blank = Standard 08 = 8 Pin Profile 3 X = XR7 2 digit significant M = ±20% S = Special P = Tin/Lead, Bulk (Dash Number) 18 = 18 Pin 4 S = Special figure, followed S = Special (up to 3 digits) 0 = Special by a multiplier From 1-999 330 = 33pF as applicable 392 = 3900pF 104 = 1uF Historical Part Number example: CS20108D1C103K5 (will continue to be accepted) CS201 08 D HISTORICAL MODEL PIN COUNT PACKAGE HEIGHT www.vishay.com 58 1 C 103 K SCHEMATIC CHARACTERISTIC CAPACITANCE TOLERANCE VALUE For Technical Questions, contact: [email protected] 5 P03 VOLTAGE PACKAGING Document Number: 31522 Revision 10-Sep-04 CS201 Vishay Dale Capacitor Networks, Single-In-Line, Coated SIP, "D" Profile DIMENSIONS in inches [millimeters] 0.085 [2.160] Typ. L Max. 0.050 [1.27] Typ. 0.135 [3.43] Max. 0.300 [7.62] CL Seating Plane for 0.040 [1.016] Ø Hole 0.007 [0.178] Ref. 0.010 [0.254] 0.020 [0.508] 0.135 + 0.015 - 0.010 [3.43 + 0.381 - 0.254] 0.050 [1.27] 0.100 ± 0.005 [2.54 ± 0.127] Non-Cumulative at Point of Egress Pin #1 is extreme left-hand terminal on side with marking. NUMBER OF PINS L MAXIMUM NUMBER OF PINS L MAXIMUM NUMBER OF PINS L MAXIMUM 4 pin 0.400 [10.16] 9 pin 0.900 [22.86] 14 pin 1.400 [35.56] 5 pin 0.500 [12.70] 10 pin 1.000 [25.40] 15 pin 1.500 [38.10] 6 pin 0.600 [15.24] 11 pin 1.100 [27.94] 16 pin 1.600 [40.64] 7 pin 0.700 [17.78] 12 pin 1.200 [30.48] 17 pin 1.700 [43.18] 8 pin 0.800 [20.32] 13 pin 1.300 [33.02] 18 pin 1.800 [45.72] SCHEMATICS Schematic 3 Schematic 1 1 2 3 4 5 6 n-1 n Common Bus - 1 Ground Lead Document Number: 31522 Revision 10-Sep-04 1 2 3 4 5 6 Schematic 4 7 8 n-1 n Isolated Capacitor Sections For Technical Questions, contact: [email protected] 1 2 3 4 n-1 n Common Bus - 2 Ground Leads www.vishay.com 59 CS206 Vishay Dale Resistor/Capacitor Networks ECL Terminators and Line Terminator, Conformal Coated, SIP FEATURES • • • • • 4 to 18 pins available X7R and COG capacitors available Low cross talk Custom design capability "B" 0.250" [6.35mm], "C" 0.350" [8.89mm] and "E" 0.325" [8.26mm] maximum seated height available, dependent on schematic • 10k ECL terminators, Circuits E and M. 100k ECL terminators, Circuit A. Line terminator, Circuit T. STANDARD ELECTRICAL SPECIFICATIONS VISHAY PROFILE SCHEMATIC DALE POWER MODEL RATING P70°C W RESISTOR CHARACTERISTICS RESISTANCE RESISTANCE TEMP. T.C.R. RANGE TOLERANCE COEFF. TRACKING Ω ±% ± ppm/°C ± ppm/°C CAPACITOR CHARACTERISTICS CAPACITANCE CAPACITANCE RANGE TOLERANCE ±% CS206 B M E 0.125 10-1M 2, 5 200 100 0.01µF 10(K), 20(M) CS206 C T 0.125 10-1M 2, 5 200 100 33pF to 0.1µF 10(K), 20(M) CS206 E A 0.125 10-1M 2, 5 200 100 0.01µF 10(K), 20(M) Capacitor Temperature Coefficient: COG maximum 0.15%, X7R maximum 2.5% TECHNICAL SPECIFICATIONS PARAMETER UNIT Operating Voltage (at + 25°C) VAC Dissipation Factor (maximum) % Insulation Resistance (at + 25C /rated voltage) CS206 Package Power Rating (maximum at 70°C): 8 PINS = 0.80 Watt C0G = 0.15; X7R = 2.5 9 PINS = 0.90 Watt 10 PINS = 1.00 Watt 100,000 50 maximum MΩ Dielectric Test V 2.5 x rated voltage Operating Temperature Range °C - 55 to + 125°C SCHEMATICS in inches [millimeters] 0.250" [6.35] High 0.250" [6.35] High ("B" Profile) ("B" Profile) ... 1 2 3 4 5 6 7 EIA Characteristics: COG and X7R (COG capacitors may be substituted for X7R capacitors). 0.325" [8.26] High ("E" Profile) 0.350" [8.89] High ("C" Profile) ... N 1 2 Circuit E 3 4 5 6 7 ... N 1 2 Circuit M 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 N Circuit T Circuit A GLOBAL PART NUMBER INFORMATION New Global Part Numbering: 20608EC103G471KP (preferred part numbering format) 2 0 6 0 8 E C 1 0 3 G 4 7 1 K P GLOBAL PIN PACKAGE/ CHARACTERISTIC RESISTANCE RES. CAPACITANCE CAP. PACKAGING SPECIAL MODEL COUNT SCHEMATIC HEIGHT TOLERANCE VALUE TOLERANCE 206 = CS206 04 = 4 Pin E = BE C = COG 2 digit significant G = ± 2% (in picofarads) K = ±10% E = Lead Free, Bulk Blank = Standard 08 = 8 Pin M = BM X = XR7 figure, followed J = ± 5% 2 digit significant M = ±20% P = Tin/Lead, Bulk (Dash Number) 18 = 18 Pin A = EA S = Special by a multiplier S = Special figure, followed S = Special (up to 2 digits) T = CT 100 = 10Ω by a multiplier S = Special 333 = 33KΩ 330 = 33pF 105 = 1MΩ 392 = 3900pF 104 = 1µF Historical Part Number example: CS20608BEC103G471KP03 (will continue to be accepted) CS206 08 B HISTORICAL MODEL PIN COUNT PACKAGE HEIGHT www.vishay.com 60 E C SCHEMATIC CHARACTERISTIC 103 G 471 K P03 RESISTANCE RES CAPACITANCE CAP PACKAGING TOLERANCE VALUE TOLERANCE VALUE For Technical Questions, contact: [email protected] Document Number: 31519 Revision 10-Sep-04 CS206 Vishay Dale Res/CapNetworks, ECL Terminators and Line Terminator DIMENSIONS in inches [millimeters] NUMBER OF PINS L MAXIMUM 4 pin 5 pin 6 pin 7 pin 8 pin 9 pin 10 pin 11 pin 12 pin 13 pin 14 pin 15 pin 16 pin 17 pin 18 pin 0.400 [10.16] 0.500 [12.70] 0.600 [15.24] 0.700 [17.78] 0.800 [20.32] 0.900 [22.86] 1.000 [25.40] 1.100 [27.94] 1.200 [30.48] 1.300 [33.02] 1.400 [35.56] 1.500 [38.10] 1.600 [40.64] 1.700 [43.18] 1.800 [45.72] 0.085 [2.160] Typ. L Max. 0.050 [1.27] Typ. 0.135 [3.43] Max. H Max. CL Seating Plane for 0.040 [1.016] Ø Hole 0.010 [0.254] 0.020 [0.508] 0.100 ± 0.005 [2.54 ± 0.127] Non-Cumulative at Point of Egress 0.135 + 0.015 - 0.010 [3.43 + 0.381 - 0.254] 0.050 [1.27] 0.007 [0.178] Ref. H (Height) Maximum: B = 0.250" [6.35] (Circuit E and M) C = 0.350" [8.89] (Circuit T) E = 0.325" [8.26] (Circuit A) Power Dissipation % Pin #1 is extreme left-hand terminal on side with marking. 150 MATERIAL SPECIFICATIONS 100 50 0 0 25 50 Derating 75 70 100 125 Flammability: UL 94V-0. Lead Material: Phosphorus-bronze, solder plated. Body Material: Epoxy coated. Solderability: Per MIL-STD-202, Method 208E. Part Marking: Pin #1 identification, part number (abbreviated as space allows), DALE® or D, date code Moisture Resistance: Meets requirements of MIL-STD202, Method 106. 150 Ambient Temperature °C PERFORMANCE MAX. ∆R (Typical Test Lots) TEST CONDITION Thermal Shock Subject to 5 cycles from - 65°C to + 125°C. ± 0.5% ∆R Short Time Overload 2.5 x rated working voltage for 5 seconds at + 25°C. ± 0.25% ∆R Moisture Resistance Cycle from + 25°C to + 65°C to + 25°C over 8 hours at 90 - 98% relative humidity, with 10% of rated power applied, for 20 cycles. Stop cycling after an even number of cycles and stabilize networks at high humidity for 1 to 4 hours. Condition networks at -10°C for 3 hours, then return to temperature cycling. On completion of cycling condition networks at + 25°C at 50% r.h. for 22 to 24 hours. ± 0.5% ∆R Resistance to Soldering Heat Immerse pins in melted solder to the lead standoffs at + 350°C for 3 seconds max. ± 0.25% ∆R Mechanical Shock 18 shocks of 100 G and 6 ms. ± 0.25% ∆R Vibration 12 cycles varied logarithmically from 10Hz to 2000Hz to 10Hz over 20 minutes. ± 0.25% ∆R Load Life 1000 hours at + 70°C, rated power applied 1.5 hours “ON, 0.5 hour “OFF”. ± 1.0% ∆R Resistance to Solvents Immerse and scrub samples with isopropyl alcohol, trichlorethylene and Freon TMC. Marking remains legible Solderability Immerse leads in 60/40 tin-lead solder using R flux at + 245°C for 5 seconds maximum. Minimum 95% solder coverage Terminal Strength Withstand 2.2 kg pull 1 minute. ± 0.25% ∆R Case Insulation Resistance 100 V applied between case and terminals tied together. IR = 10,000 Megohm minimum Document Number: 31519 Revision 10-Sep-04 For Technical Questions, contact: [email protected] www.vishay.com 61 MDRC Vishay Dale Resistor/Capacitor Networks, Dual-In-Line, Molded DIP, 16 Pin FEATURES • 0.190" [4.83mm] maximum seated height • Rugged molded case construction • Highly stable thick film • Reduces total assembly cost • Low temperature coefficient (- 30°C to + 85°C) ± 100ppm/°C • Compatible with automatic insertion equipment • Reduces PC board space STANDARD ELECTRICAL SPECIFICATIONS GLOBAL SCHEMATIC POWER MODEL RATING MDRC 1641 RESISTOR CHARACTERISTICS PACKAGE RESISTANCE TEMPERATURE T.C.R. POWER TOLERANCE COEFFICIENT TRACKING P25°C RATING (- 20°C to + 85°C) W W @ + 25°C ±% Typical ± ppm/°C 0.15 max 2.0 max. ± 2, or 2Ω* ± 100ppm/°C 50 CAPACITOR CHARACTERISTICS CAPACITANCE CAPACITANCE TOLERANCE VOLTAGE RATING V Max. 0.1µF + 40%, - 20% 25 MDRC 1642 0.15 max. 2.0 max. ± 2, or 2Ω* ± 100ppm/°C 50 0.1µF + 40%, - 20% 25 MDRC 1643 0.20 max. 2.0 max. ± 2, or 2Ω* ± 100ppm/°C 50 0.1µF + 40%, - 20% 25 * Whichever is greater GLOBAL PART NUMBER INFORMATION New Global Part Numbering: MDRC1641500GD04 (preferred part numbering format) M GLOBAL MODEL MDRC D R PIN COUNT 16 = 16 Pin C 1 6 4 1 5 0 0 G RESISTANCE TOLERANCE VALUE CODE 41 = ECL Terminator 2 digit G = ± 2% 42 = ECL Pull-Down significant figure, S = Special 00 = Special followed by a multiplier 680 = 68Ω 511 = 510Ω Historical Part Number example: MDRC1641500G (will continue to be accepted) D 0 SCHEMATIC 4 PACKAGING SPECIAL E04 = Lead Free, Tube D04 = Tin/Lead, Tube Blank = Standard (Dash Number) (up to 3 digits) MDRC 16 41 500 G D04 HISTORICAL MODEL PIN COUNT SCHEMATIC RESISTANCE VALUE TOLERANCE CODE PACKAGING New Global Part Numbering: MDRC1643750GD04 (preferred part numbering format) M GLOBAL MODEL MDRC D PIN COUNT 16 = 16 Pin R C 1 SCHEMATIC 43 = Thevenin Terminator 6 4 3 7 IMPEDENCE VALUE 2 digit significant figure, followed by a multiplier 500 = 50Ω 5 0 G TOLERANCE CODE G = ± 2% J = ± 5% D 0 4 PACKAGING SPECIAL E04 = Lead Free, Tube D04 = Tin/Lead, Tube Blank = Standard (Dash Number) (up to 3 digits) Historical Part Number example: MDRC1643750G (will continue to be accepted) MDRC 16 43 750 G D04 HISTORICAL MODEL PIN COUNT SCHEMATIC IMPEDENCE VALUE TOLERANCE CODE PACKAGING www.vishay.com 62 For Technical Questions, contact: [email protected] Document Number: 31524 Revision 10-Sep-04 MDRC Resistor/Capacitor Networks, Dual-In-Line, Molded DIP, 16 Pin Vishay Dale DIMENSIONS in inches [millimeters] 0.310 ± 0.010 [7.87 ± 0.254] 0.850 ± 0.010 [21.59 ± 0.254] 0.150 ± 0.005 [3.81 ± 0.127] 0.030 [0.762] Typ. 0.075 ± 0.015 [1.90 ± 0.381] Pin #1 Identification 0.100 ± 0.010 [2.54 ± 0.254] Non-Accumulative Tol. 7 Spaces Pin #1 0.018 ± 0.003 [0.457 ± 0.076] 0.700 ± 0.010 [17.78 ± 0.254] 0.250 ± 0.005 [6.35 ± 0.127] 0.130 + 0.015 - 0.010 [3.30 + 0.381 - 0.254] 0.010 + 0.005 - 0.002 [0.254 + 0.127 - 0.051] 0.290 [7.37] Min. 0.320 [8.13] Nom. 0.360 [9.14] Max. 0.050 ± 0.005 [1.27 ± 0.127] RESISTANCE VALUE IN OHMS (G Tolerance) MDRC1643 MDRC1641 50, 68, 75, 100 R1 R2 Zo MDRC1642 81 121 162 130 195 260 50 75 100 510 TECHNICAL SPECIFICATIONS PARAMETER UNIT MDRC Operating Voltage (at + 25°C) VAC 50 maximum % <3 Capacitor Dissipation Factor Voltage Coefficient of Resistance (typical) ppm/V < 50 Operating Temperature Range °C - 30 to + 85°C Storage Temperature Range °C - 30 to + 85°C MECHANICAL SPECIFICATIONS Marking Resistance to Solvents: Permanency testing per MIL-STD-202, Method 215. Solderability: Per MIL-STD-202, Method 208E. Terminals: Copper alloy, solder plated. Body: Molded epoxy. Weight: 1.5 grams. Document Number: 31524 Revision 10-Sep-04 For Technical Questions, contact: [email protected] www.vishay.com 63 MDRC Vishay Dale Resistor/Capacitor Networks, Dual-In-Line, Molded DIP, 16 Pin CIRCUIT APPLICATIONS MDRC1641 Schematic - 2.0 and - 5.2 Volt ECL Terminator 16 9 1 8 The MDRC1641 circuit contains 11 resistors of nominally equal value and a .01 microfarad decoupling capacitor. The MDRC-1641 is designed for ECL Line Termination to a - 2.0 volt buss. The .01 microfarad decoupling capacitor is for bypassing transients between supply voltages. MDRC1642 Schematic 16 9 1 8 The MDRC1642 circuit contains 12 resistors of 510 ohm each and a .01 microfarad decoupling capacitor. The MDRC-1642 is designed for ECL Pull-down to a - 5.2 volt buss. The .01 microfarad decoupling capacitor is for bypassing voltage transients on the voltage buss. MDRC1643 Schematic VCC LINE 1 VEE LINE 2 LINE 3 VCC Thevenin Equivalent Terminator VEE LINE 2 The MDRC1643 contains four pair of series resistors. The circuit is compatible with ECL pin configurations. Each terminator section (series pair) contains a voltage divider between VCC (0 volt) and VEE (- 5.2 volt) providing a Thevenin equivalent voltage of - 2.0 volts. A .01 microfarad decoupling capacitor bypasses the VEE buss. 16 R1 1 VCC R1 R2 VEE R2 VCC VEE R1 R1 R2 R2 VEE VCC VEE C VEE Power Rating (Watts) MDRC1641 and MDRC1642 MDRC1641 MDRC1642 Package 2.00 1.00 0.15 Single Resistor - 50 - 30 + 25 Derating + 85 + 150 Ambient Temperature °C Power Rating (Watts) MDRC1643 MDRC1643 Package 2.00 1.00 0.20 - 50 - 30 Derating www.vishay.com 64 Single Resistor + 25 + 85 + 150 Ambient Temperature °C For Technical Questions, contact: [email protected] Document Number: 31524 Revision 10-Sep-04 MDRC Resistor/Capacitor Networks, Dual-In-Line, Molded DIP, 16 Pin Vishay Dale PERFORMANCE TEST CONDITIONS Thermal Shock MDRC1641 and MDRC1642, 5 cycles between - 30°C and + 85°C MDRC1643, 5 cycles between - 65°C and + 125°C Short Time Overload 2.5 x rated working voltage 5 seconds Low Temperature Operation MDRC1641 and MDRC1642, 45 minutes at full rated working voltage at - 30°C MDRC1643, 45 minutes at full rated working voltage at - 65°C Moisture Resistance 240 hours with humidity ranging from 80% RH to 98% RH Resistance to Soldering Heat Leads immersed in + 350°C solder to within 1/16" of device body for 3 seconds Shock Total of 18 shocks at 100 G's Vibration 12 hours at maximum of 20 G's between 10 and 2,000 Hz Load Life 1000 hours at + 70°C, rated power applied 1.5 hours “ON”, 0.5 hour “OFF” for full 1000 hour period. Derated according to the curve. Terminal Strength 4.5 pound pull for 30 seconds Insulation Resistance 10,000 Megohm (minimum) Dielectric Withstanding Voltage (200 V RMS for 1 minute) Document Number: 31524 Revision 10-Sep-04 For Technical Questions, contact: [email protected] MAX. ∆R (Typical Test Lots) ± 0.50% ∆R ± 0.25% ∆R ± 0.25% ∆R ± 0.50% ∆R ± 0.25% ∆R ± 0.25% ∆R ± 0.25% ∆R ± 0.50% ∆R ± 0.25% ∆R — — www.vishay.com 65 www.vishay.com 66 Model Numbers DFM....................68 MDM14, 16 .........72 MSM ...................76 MIL Resistor Networks SIL, DIL or Custom Configurations • Isolated, Bussed or TTL-Terminator Circuits • High Packaging Density DFM Vishay Dale Thick Film Resistor Networks, Military, MIL-PRF-83401 Qualified, Type RZ030, Schematics A (11), B (12), J (15) FEATURES • 11, 12, 15 Schematics; hot-solder dipped • MIL-PRF-83401 qualified • Highly stable thick film • TCR available in "K" (± 100ppm/°C) or "M" (± 300ppm/°C) characteristic • 100% screen tested per Group A, Subgroup 1 of MIL-PRF-83401 • 0.065" [1.65mm] height for high density packaging STANDARD ELECTRICAL SPECIFICATIONS VISHAY DALE MODEL DFM POWER RATING P70°C ELEMENT W 0.050 0.025 0.015 P70°C PACKAGE W 0.350 0.325 0.350 CIRCUIT SCHEMATIC LIMITING ELEMENT VOLTAGE MAX. V 11 12 15 50 50 50 COEFFICIENT1) (-55°C to + 125°C) STANDARD2) TOLERANCE % RESISTANCE RANGE Ω K, M K, M K, M 2 2 2 10R0 – 1M0 10R0 – 1M0 see table TEMPERATURE 1) K = ± 100ppm/°C; M = ± 300ppm/°C 1% and ± 5% tolerance available • Consult factory for stocked values 2) ± GLOBAL PART NUMBER INFORMATION New Global Part Numbering: M8340103M6801GAD05 (preferred part numbering format) M MIL STYLE 8 3 4 0 1 0 3 M 6 8 0 1 G SPEC SHEET CHARACTERISTIC RESISTANCE TOLERANCE VALUE M83401 03 K = 100ppm 3 digit significant F = ± 1% M = 300ppm figure, followed G = ± 2% by a multiplier J = ± 5% 10R0 = 10Ω 3302 = 33KΩ 1004 = 1MΩ Historical Part Number example: M8340103M6801GA (will continue to be accepted) A D 0 5 SCHEMATIC PACKAGING A = Isolated B = Bussed D05 = Tin/Lead, Tube M83401 03 M 6801 G A D05 MIL STYLE SPEC SHEET CHARACTERISTIC RESISTANCE VALUE TOLERANCE SCHEMATIC PACKAGING New Global Part Numbering: M8340103KA001GJD05 (preferred part numbering format) M MIL STYLE M83401 8 3 4 0 1 0 SPEC SHEET CHARACTERISTIC 03 K = 100ppm M = 300ppm 3 K A RESISTANCE VALUE Per std. Mil. Spec (see Impedence Codes table) 0 0 1 J A D 0 5 TOLERANCE SCHEMATIC PACKAGING F = ± 1% G = ± 2% J = ± 5% J = Dual Terminator D05 = Tin/Lead, Tube Historical Part Number example: M8340103KA001GJ (will continue to be accepted) M83401 03 K A001 G J D05 MIL STYLE SPEC SHEET CHARACTERISTIC RESISTANCE VALUE TOLERANCE SCHEMATIC PACKAGING www.vishay.com 68 For technical questions contact: [email protected] Document Number: 31517 Revision: 10-Sep-04 DFM Vishay Dale Thick Film Resistor Networks, Flat Pack DIMENSIONS in inches [millimeters] Pin #1 0.050 [1.27] Typ. 0.019 ± 0.006 [0.483 ± 0.15] 0.200 0.400 DFM1412 Package 0.325 0.200 DFM1415 Package 0.350 Single Resistor 0.050 0.025 Derating 0.400 0.200 Single Resistor - 55 + 25 + 70 + 125 + 150 Ambient Temperature °C 0.005 + 0.004 - 0.002 [0.127 + 0.102 - 0.051] 15 Schematic Power Rating (Watts) DFM1411 Package 0.350 0.250 [6.35] Min. 0.825 [20.96] Max. 12 Schematic Power Rating (Watts) Power Rating (Watts) 0.075 [1.91] Max. 0.305 [7.75] Max. 11 Schematic 0.400 0.250 [6.35] Min. 0.365 [9.27] Min. 0.385 [9.78] Max. Single Resistor 0.015 - 55 + 25 + 70 + 125 + 150 Ambient Temperature °C - 55 + 25 + 70 + 125 + 150 Ambient Temperature °C MECHANICAL SPECIFICATIONS Marking Resistance to Solvents Permanency testing per MIL-PRF-83401 Solderability Per MIL-PRF-83401. Per MIL-STD-1276 DFM1411, DFM1412 and DFM1415 = Type G (hot solder dipped) Hot solder dipped leads supplied as standard finish. Terminals Body Epoxy filled ceramic sandwich IMPEDANCE CODES CODE R1 (Ω) R2(Ω) CODE R1(Ω) R2(Ω) A001 82 130 A010 330 470 A002 120 200 A011 330 680 A003 130 210 A012 1.5K 3.3K A004 160 260 A013 3K 6.2K A005 180 240 A014 180 270 A006 180 390 A015 270 270 A007 220 270 A016 560 560 A008 220 330 A017 560 1.2K A009 330 390 A018 620 2.7K Document Number: 31517 Revision: 10-Sep-04 For technical questions contact: [email protected] www.vishay.com 69 DFM Vishay Dale CIRCUIT APPLICATIONS 11 Schematic DFM1411 (M8340103xxxxxxA) 7 isolated resistors The DFM1411 provides the user with 7 nominally equal resistors with each resistor isolated from all others. Commonly used in the following applications: • "Wired OR" Pull-up • Line Termination • LED Current Limiting • Power Driven Pull-up • ECL Output Pull-down • Power Gate Pull-up • TTL Input Pull-down • Long-line Impedance balancing DFM1411 Pin #1 12 Schematic DFM1412 (M8340103xxxxxxB) 13 resistors with one pin common The DFM1412 provides the user with a choice of 13 nominally equal resistors, each connected to a common pin. Commonly used in the following applications: • MOS/ROM Pull-up/ • "Wired OR" Pull-up • Digital Pulse Squaring • Pull-down • Power Driven Pull-up • TTL Input Pull-down • Open Collector Pull-up • TTL Unused Gate Pull-up • High Speed Parallel Pull-up • • • • • • • DFM1412 Pin #1 15 Schematic 14 R1 R1 R2 R1 1R2 R1 R2 R1 R2 R1 R1 R2 R1 R2 R2 R1 R2 R1 R2 DFM1415 www.vishay.com 70 R1 R2 R2 R1 R2 DFM1415 (M8340103xxxxxxJ) 12 pairs of resistors The DFM1415 provides the user with a choice of 12 pairs of R1/R2 resistor values for pulse squaring and TTL dual-line terminating requirements. For technical questions contact: [email protected] Document Number: 31517 Revision: 10-Sep-04 DFM Thick Film Resistor Networks, Flat Pack Vishay Dale PERFORMANCE MAX. ∆R (Typical Test Lots) TEST CONDITIONS Power Conditioning 1.5 x rated power, applied 1.5 hours “ON” and 0.5 hours “OFF” for 100 hours ± 4 hours at + 25°C ambient temperature ± 0.50% ∆R Thermal Shock 5 cycles between - 65°C and + 125°C ± 0.50% ∆R Short Time Overload 2.5 x rated working voltage, 5 seconds ± 0.25% ∆R (Char. K) ± 0.50% ∆R (Char. M) Low Temperature Operation 45 minutes at full rated working voltage at - 65°C ± 0.25% ∆R (Char. K) ± 0.50% ∆R (Char. M) Moisture Resistance 240 hours with humidity ranging from 80% RH to 98% RH ± 0.50% ∆R Resistance to Soldering Heat Leads immersed in + 260°C solder to within 1/16" of body for 10 seconds ± 0.25% ∆R Shock Total of 18 shocks at 100 g's ± 0.25% ∆R Vibration 12 hours at maximum of 20 g's between 10 and 2,000 Hz ± 0.25% ∆R Load Life 1000 hours at + 70°C, rated power applied 1.5 hours “ON”, 0.5 hour “OFF” for full 1000 hour period Terminal Strength 1.5 pound pull for 30 seconds Insulation Resistance 10,000 Megohm (minimum) - Dielectric Withstanding Voltage No evidence of arcing or damage (200 V RMS for 1 minute) - Document Number: 31517 Revision: 10-Sep-04 For technical questions contact: [email protected] ± 0.50% ∆R (Char. K) ± 2.0% ∆R (Char. M) ± 0.25% ∆R www.vishay.com 71 MDM Vishay Dale Thick Film Resistor Networks Military, MIL-PRF-83401 Qualified, Type RZ Dual-In-Line Package, 01, 03, 05 Schematics FEATURES • • • • • MIL-PRF-83401 qualified Epoxy molded construction All device leads are hot-solder dipped Available in tube pack TCR available in "K" (± 100ppm/°C) or "M" (± 300ppm/°C) depending on style • 100% screen tested per Group A, Subgroup 1 of MIL-PRF83401 • All devices are capable of passing the MIL-STD-202, Method 210, Condition D, "Resistance to Soldering Heat" test STANDARD ELECTRICAL SPECIFICATIONS VISHAY SCHEMATIC RESISTOR PACKAGE DALE POWER RATING POWER RATING Max. @ 70°C MODEL/ Max. @ 70°C PIN NO./ W W MDM 14 01 0.10 1.30 MDM 14 03 0.20 1.40 MDM 14 05 0.05 1.20 MDM 16 01 0.10 1.50 MDM 16 03 0.20 1.60 MDM 16 05 0.05 1.40 * K = ± 100ppm/°C; M = ± 300ppm/°C **± 1% and ± 5% tolerances available on request. RESISTANCE RANGE STANDARD TOLERANCE Ω % ± 2 (± 1, ± 5)** ± 2 (± 1, ± 5)** ± 2 (± 1, ± 5)** ± 2 (± 1, ± 5)** ± 2 (± 1, ± 5)** ± 2 (± 1, ± 5)** 10 - 1M 10 - 1M Consult factory 10 - 1M 10 - 1M Consult factory TEMPERATURE COEFFICIENT* (- 55°C to + 125°C) WEIGHT g 1.3 1.3 1.3 1.5 1.5 1.5 K, M K, M K, M K, M K, M K, M GLOBAL PART NUMBER INFORMATION New Global Part Numbering: M8340101M2201GBD04 (preferred part numbering format) M MIL STYLE M83401 8 3 4 0 1 SPEC SHEET CHARACTERISTIC VALUE 01 = 14 Pin K = 100ppm 02 = 16 Pin M = 300ppm 0 1 M 2 RESISTANCE 2 0 1 TOLERANCE 3 digit significant F = ± 1% figure, followed G = ± 2% by a multiplier J = ± 5% 10R0 = 10Ω 3302 = 33KΩ 1004 = 1MΩ Historical Part Number example: M8340101M2201GB (will continue to be accepted) G B D 0 4 SCHEMATIC PACKAGING A = Isolated B = Bussed D04 = Tin/Lead, Tube M83401 01 M 2201 G B D04 MIL STYLE SPEC SHEET CHARACTERISTIC RESISTANCE VALUE TOLERANCE SCHEMATIC PACKAGING New Global Part Numbering: M8340102KA001GJD04 (preferred part numbering format) M MIL STYLE M83401 8 3 4 0 1 SPEC SHEET CHARACTERISTIC 01 = 14 Pin 02 = 16 Pin K = 100ppm M = 300ppm 0 2 K RESISTANCE VALUE Per std. Mil. Spec (see Impedence codes table) A 0 0 1 G J D 0 4 TOLERANCE SCHEMATIC PACKAGING F = ± 1% G = ± 2% J = ± 5% J = Dual Terminator D04 = Tin/Lead, Tube Historical Part Number example: M8340102KA001GJ (will continue to be accepted) M83401 02 K A001 G J D04 MIL STYLE SPEC SHEET CHARACTERISTIC RESISTANCE VALUE TOLERANCE SCHEMATIC PACKAGING www.vishay.com 72 For Technical Questions, contact: [email protected] Document Number: 31516 Revision 10-Sep-04 MDM Thick Film Resistor Networks, Military, MIL-PRF-83401 -Type RZ Vishay Dale DIMENSIONS in inches [millimeters] TYP 0.030 [0.762] 0.310 ± 0.010 [7.87 ± 0.254] A ± 0.010 [0.254] 0.250 ± 0.005 [6.35 ± 0.127] 0.120 ± 0.005 [3.05 ± 0.127] Pin #1 Identification 0.075 ± 0.015 [1.90 ± 0.381] Pin #1 0.100 ± 0.010 [2.54 ± 0.254] 0.018 ± 0.003 [0.457 ± 0.076] B ± 0.010 [0.254] 0.010 + 0.005 - 0.002 [0.254 + 0.127 - 0.051] 0.290 Min. 0.320 Nom. 0.360 Max. [7.37 Min. 8.13 Nom. 9.14 Max.] 0.050 ± 0.005 [1.27 ± 0.127] Non-Accumulative Tol. "C" Spaces VISHAY DALE MODEL 0.130 + 0.015 - 0.005 [3.30 + 0.381 - 0.127] A B C MDM14 0.750 [19.05] 0.600 [15.24] 6 MDM16 0.850 [21.59] 0.700 [17.78] 7 IMPEDANCE CODES CODE A001 A002 A003 A004 A005 A006 A007 A008 A009 R1(Ω) R2(Ω) 82 120 130 160 180 180 220 220 330 130 200 210 260 240 390 270 330 390 CODE A010 A011 A012 A013 A014 A015 A016 A017 A018 R1(Ω) R2(Ω) 330 330 1.5K 3K 180 270 560 560 620 470 680 3.3K 6.2K 270 270 560 1.2K 2.7K TECHNICAL SPECIFICATIONS PARAMETER UNIT MDM Series Maximum Operating Voltage VDC 100 Veff < 50ppm VAC 200 per min. Insulation Resistance Ω 10,000M Operating Temperature Range °C - 55 to + 125 Storage Temperature Range °C - 55 to + 150 Voltage Coefficient of Resistance Dielectric Strength MECHANICAL SPECIFICATION Marking Resistance to Solvents: Permanency testing per MIL-PRF-83401. Solderability: Per MIL-PRF-83401. Body: Molded epoxy. Terminals: Copper alloy, hot-solder dipped. Document Number: 31516 Revision 10-Sep-04 For Technical Questions, contact: [email protected] www.vishay.com 73 MDM Vishay Dale Thick Film Resistor Networks, Military, MIL-PRF-83401-Type RZ CIRCUIT APPLICATIONS 01 Schematic MDM1401 (M8340101xxxxxxB) MDM1601 (M8340102xxxxxxB) 13 or 15 resistors with one pin common The MDMxx01 provides the user with a choice of 13 or 15 nominally equal resistors, each connected to a common pin. Commonly used in the following applications: • MOS/ROM Pull-up/Pull-down • TTL Input Pull-down • Open Collector Pull-up • Digital Pulse Squaring • "Wired OR" Pull-up • TTL Unused Gate Pull-up • Power Driven Pull-up • High Speed Parallel Pull-up • • • • • • • • MDM1401 MDM1601 Pin #1 03 Schematic MDM1403 (M8340101xxxxxxA) MDM1603 (M8340102xxxxxxA) 7 or 8 isolated resistors The MDMxx03 provides the user with a choice of 7 or 8 nominally equal resistors, with each resistor isolated from all others. Commonly used in the following applications: • "Wired OR" Pull-up • Long-line Impedance Balancing • Power Driven Pull-up • LED Current Limiting • Power Gate Pull-up • ECL Output Pull-down • Line Termination • TTL Input Pull-down MDM1403 MDM1603 Pin #1 05 Schematic R1 R1 R2 R1 R2 R1 R2 R1 R2 Pin #1 R1 R2 R1 R2 R1 R2 R1 R2 R1 R2 R1 R2 R2 R1 R2 MDM1405 (M8340101xxxxxxJ) MDM1605 (M8340102xxxxxxJ) 12 or 14 resistor pairs R1 R2 R1 The MDMxx05 provides the user with a choice of 12 or 14 pairs of R1/R2 resistor values for pulse squaring and TTL dual-line terminating requirements. R2 01 Schematic 03 Schematic 05 Schematic Power Rating (Watts) Power Rating (Watts) Power Rating (Watts) MDM1405, MDM1605 MDM 16 1.50 MDM 14 1.30 1.00 0.10 - 55 Derating www.vishay.com 74 + 25 + 70 + 125 + 150 Ambient Temperature °C MDM 14 1.40 1.00 0.20 Single Resistor MDM 16 1.60 1.40 MDM 16 1.20 MDM 14 1.00 Single Resistor - 55 + 25 + 70 + 125 + 150 Single Resistor 0.05 - 55 + 25 Ambient Temperature °C For Technical Questions, contact: [email protected] + 70 + 125 + 150 Ambient Temperature °C Document Number: 31516 Revision 10-Sep-04 MDM Thick Film Resistor Networks, Military, MIL-PRF-83401-Type RZ Vishay Dale PERFORMANCE MAX. ∆R (Typical Test Lots) TEST CONDITIONS Power Conditioning 1.5 x rated power, applied 1.5 hours “ON” and 0.5 hour “OFF” for 100 hours ± 4 hours at + 25°C ambient temperature ± 0.50% ∆R Thermal Shock 5 cycles between - 65°C and + 125°C ± 0.50% ∆R Short Time Overload 2.5 x rated working voltage 5 seconds ± 0.25% ∆R (Char. K) ± 0.50% ∆R (Char. M) Low Temperature Operation 45 minutes at full rated working voltage at - 65°C ± 0.25% ∆R (Char. K) ± 0.50% ∆R (Char. M) Moisture Resistance 240 hours with humidity ranging from 80% RH to 98% RH ± 0.50% ∆R Resistance to Soldering Heat Leads immersed in + 260°C solder to within 1/16" of body for 10 seconds ± 0.25% ∆R Shock Total of 18 shocks at 100 G's ± 0.25% ∆R Vibration 12 hours at maximum of 20 G's between 10 and 2,000 Hz ± 0.25% ∆R Load Life 1,000 hours at + 70°C, rated power applied 1.5 hours “ON”, 0.5 hour “OFF” for full 1000 hour period ± 0.50% ∆R (Char. K) ± 2.00% ∆R (Char. M) Terminal Strength 4.5 pound pull for 30 seconds ± 0.25% ∆R Insulation Resistance 10,000 Megohm (minimum) — Dielectric Withstanding Voltage No evidence of arcing or damage (200 V RMS for 1 minute) — Document Number: 31516 Revision 10-Sep-04 For Technical Questions, contact: [email protected] www.vishay.com 75 MSM Vishay Dale Thick Film Resistor Networks Military, MIL-PRF-83401 Qualified, Type RZ Single-In-Line, Molded SIP; 01, 03, 05 Schematics FEATURES • MIL-PRF-83401 qualified • 0.195" [4.95mm] "A" and 0.350" [8.89mm] "C" maximum seated heights • Highly stable thick film • TCR available in "K" (± 100ppm/°C) or "M" (± 300ppm/°C) characteristic • All device leads are hot-solder dipped • Rugged molded case construction • Compatible with automatic insertion equipment • 100% screen tested per Group A, Subgroup 1 of MIL-PRF-83401 • All devices are capable of passing the MIL-STD-202, Method 210, Condition D "Resistance to Soldering Heat" test • Available in tube pack STANDARD ELECTRICAL SPECIFICATIONS VISHAY DALE MODEL/ PIN NO/ PROFILE MSM06A MSM08A MSM10A MSM06A MSM08A MSM10A MSM06A MSM08A MSM10A MSM06C MSM08C MSM10C MSM06C MSM08C MSM10C MSM06C MSM08C MSM10C SCHEMATIC 01 01 01 03 03 03 05 05 05 01 01 01 03 03 03 05 05 05 RESISTOR POWER RATING Max. @ 70°C W 0.12 0.12 0.12 0.12 0.12 0.12 0.07 0.07 0.07 0.20 0.20 0.20 0.20 0.20 0.20 0.11 0.11 0.11 PACKAGE POWER RATING Max. @ 70°C W 0.60 0.84 1.08 0.36 0.48 0.60 0.60 0.84 1.08 1.00 1.40 1.80 0.60 0.80 1.00 0.88 1.32 1.80 * ± 1% and ± 5% available RESISTANCE RANGE STANDARD TOLERANCE* TEMPERATURE COEFFICIENT** (- 55°C to + 125°C) Ω 10 - 1M % ±2 K, M 10 - 1M ±2 K, M Consult factory ±2 K, M 10 - 1M ±2 K, M 10 - 1M ±2 K, M Consult factory ±2 K, M WEIGHT g 0.4 0.5 0.6 0.4 0.5 0.6 0.4 0.5 0.6 0.7 0.9 1.1 0.7 0.9 1.1 0.7 0.9 1.1 ** K = ± 100ppm/°C; M = ± 300ppm/°C GLOBAL PART NUMBER INFORMATION New Global Part Numbering: M8340107K1003GCD03 (preferred part numbering format) M MIL STYLE M83401 8 3 4 0 1 SPEC SHEET CHARACTERISTIC 04 = 6 Pin, “C” Profile 05 = 8 Pin, “C” Profile 06 = 10 Pin, “C” Profile 07 = 6 Pin, “A” Profile 08 = 8 Pin, “A” Profile 09 = 10 Pin, “A” Profile K = 100ppm M = 300ppm 0 7 K 1 RESISTANCE VALUE 3 digit significant figure, followed by a multiplier 10R0 = 10Ω 3302 = 33KΩ 1004 = 1MΩ 0 0 3 G C D 0 3 TOLERANCE SCHEMATIC PACKAGING F = ± 1% G = ± 2% J = ± 5% C = Bussed G = Isolated D03 = Tin/Lead, Tube Historical Part Number example: M8340107K1003GC (will continue to be accepted) M83401 07 K 1003 G C D03 MIL STYLE SPEC SHEET CHARACTERISTIC RESISTANCE VALUE TOLERANCE SCHEMATIC PACKAGING New Global Part Numbering: M8340104KA001GHD03 (preferred part numbering format) M MIL STYLE M83401 8 3 4 0 1 SPEC SHEET CHARACTERISTIC 04 = 6 Pin, “C” Profile 05 = 8 Pin, “C” Profile 06 = 10 Pin, “C” Profile 07 = 6 Pin, “A” Profile 08 = 8 Pin, “A” Profile 09 = 10 Pin, “A” Profile K = 100ppm M = 300ppm 0 4 K A RESISTANCE VALUE Per std. Mil. Spec (see Impedence Codes table) 0 0 1 G H D 0 3 TOLERANCE SCHEMATIC PACKAGING F = ± 1% G = ± 2% J = ± 5% H = Dual Terminator D03 = Tin/Lead, Tube Historical Part Number example: M8340104KA001GH (will continue to be accepted) M83401 04 K A001 G H D03 MIL STYLE SPEC SHEET CHARACTERISTIC RESISTANCE VALUE TOLERANCE SCHEMATIC PACKAGING www.vishay.com 76 For Technical Questions, contact: [email protected] Document Number: 31514 Revision 10-Sep-04 MSM Thick Film Resistor Networks, Military, MIL-PRF-83401 - Type RZ DIMENSIONS in inches [millimeters] "A" Profile 0.030 + 0.005 - 0.015 [0.762 + 0.127 - 0.381] "C" Profile 0.100 ± 0.005 [2.54 ± 0.127] Non-Accumulative 0.030 + 0.005 - 0.015 [0.762 + 0.127 - 0.381] A 0.187 + 0.008 - 0.010 [4.75 + 0.203 - 0.254] Pin # 1 0.040 + 0.009 - 0.015 [1.02 + 0.229 - 0.381] 0.135 + 0.015 - 0.010 [3.43 + 0.381 - 0.254] 0.017 ± 0.004 [0.432 ± 0.102] B C Equal Space Vishay Dale A 0.342 + 0.008 - 0.010 [8.69 + 0.203 - 0.254] Pin # 1 0.040 + 0.009 - 0.015 [1.02 + 0.229 - 0.381] 0.100 ± 0.005 [2.54 ± 0.127] Non-Accumulative 0.017 ± 0.004 0.135 + 0.015 - 0.010 [0.432 ± 0.102] [3.43 + 0.381 B 0.254] C Equals Spaces 0.098 max. [2.49 max.] 0.098 max. [2.49 max.] A B C MSM06 0.583 ± 0.015 [14.81 ± 0.381] 0.500 [12.70] 5 MSM08 0.783 ± 0.015 [19.89 ± 0.381] 0.700 [17.78] 7 MSM10 0.983 ± 0.015 [24.97 ± 0.381] 0.900 [22.86] 9 VISHAY DALE MODEL 0.012 ± 0.004 [0.305 ± 0.102] TECHNICAL SPECIFICATIONS PARAMETER Maximum Operating Voltage Voltage Coefficient of Resistance Dielectric Strength Insulation Resistance Operating Temperature Range Storage Temperature Range UNIT VDC Veff VAC Ω °C °C 0.012 ± 0.004 [0.305 ± 0.102] MECHANICAL SPECIFICATIONS MSM Series 50 < 50ppm 200 min. 10,000M - 55 to + 125 - 55 to + 150 Body: Molded epoxy. Terminals: Copper alloy, hot-solder dipped. Solderability: Per MIL-PRF-83401. MILITARY IMPEDANCE CODES CODE A001 A002 A003 A004 A005 A006 A007 A008 A009 Document Number: 31514 Revision 10-Sep-04 R1(Ω) 82 120 130 160 180 180 220 220 330 R2(Ω) 130 200 210 260 240 390 270 330 390 CODE A010 A011 A012 A013 A014 A015 A016 A017 A018 R1(Ω) 330 330 1.5K 3K 180 270 560 560 620 For Technical Questions, contact: [email protected] R2(Ω) 470 680 3.3K 6.2K 270 270 560 1.2K 2.7K www.vishay.com 77 MSM Vishay Dale Thick Film Resistor Networks, Military, MIL-PRF-83401 - Type RZ Derating 01 Schematic "C" Profile Power Rating (Watts) Power Rating (Watts) "A" Profile MSM10A Package 1.08 MSM08A Package 0.84 MSM06A Package 0.60 MSM10C Package 1.80 MSM08C Package 1.40 MSM06C Package 1.00 Single Resistor 0.12 - 55 + 25 + 70 + 125 + 150 Ambient Temperature°C - 55 0.60 0.48 0.36 0 MSM10A Package MSM08A Package 1.00 0.80 0.60 MSM08C Package MSM06C Package MSM06A Package Single Resistor Single Resistor 0.12 - 55 0 + 25 + 70 + 125 + 150 Ambient Temperature°C - 55 "A" Profile 1.08 MSM10A Package 0.84 MSM08A Package 0.60 0 + 25 + 70 + 125 + 150 Ambient Temperature°C "C" Profile Power Rating (Watts) Power Rating (Watts) + 70 + 125 + 150 Ambient Temperature°C MSM10C Package 0.20 05 Schematic + 25 "C" Profile "A" Profile Power Rating (Watts) Power Rating (Watts) 03 Schematic 0 Single Resistor 0.20 MSM10C Package 1.80 1.32 MSM08C Package MSM06A Package MSM06C Package 0.88 0.11 Single Resistor Single Resistor 0.07 - 55 www.vishay.com 78 0 + 25 + 70 + 125 + 150 Ambient Temperature°C - 55 0 For Technical Questions, contact: [email protected] + 25 + 70 + 125 + 150 Ambient Temperature°C Document Number: 31514 Revision 10-Sep-04 MSM Thick Film Resistor Networks, Military, MIL-PRF-83401 - Type RZ Vishay Dale CIRCUIT APPLICATION 5, 7 or 9 resistors with one pin common 01 Schematic "A" Profile MSM06A01 (M8340107xxxxxxC) MSM08A01 (M8340108xxxxxxC) MSM10A01 (M8340109xxxxxxC) "C" Profile MSM06C01 (M8340104xxxxxxC) MSM08C01 (M8340105xxxxxxC) MSM10C01 (M8340106xxxxxxC) The MSM06A01, MSM08A01, MSM10A01, MSM06C01, MSM08C01 and MSM10C01 molded single-in-line resistor networks provide the user with a choice of 5, 7 or 9 nominally equal resistors, each connected to a common pin (Pin No. 1). Commonly used in the following applications: 1 2 3 n-1 n • "Wired OR" Pull-up • Power Gate Pull-up • MOS/ROM Pull-up/Pull-down 03 Schematic 3, 4 or 5 isolated resistors "A" Profile MSM06A03 (M8340107xxxxxxG) MSM08A03 (M8340108xxxxxxG) MSM10A03 (M8340109xxxxxxG) 1 2 3 4 n-1 n 05 Schematic • Long-Line Impedance Balance • LED Current Limiting • ECL Output Pull-down • TTL Input Pull-down 4, 6 or 8 isolated resistors "A" Profile MSM06A05 (M8340107xxxxxxH) MSM08A05 (M8340108xxxxxxH) MSM10A05 (M8340109xxxxxxH) R2 R1 2 "C" Profile MSM06C03 (M8340104xxxxxxG) MSM08C03 (M8340105xxxxxxG) MSM10C03 (M8340106xxxxxxG) The MSM06A03, MSM08A03, MSM10A03, MSM06C03, MSM08C03 and MSM10C03 molded single-in-line resistor networks provide the user with a choice of 3, 4 or 5 nominally equal resistors. Each resistor is isolated from all others. Commonly used in the following applications: • "Wired OR" Pull-up • Power Driven Pull-up • Power Gate Pull-up • Line Termination 1 • Open Collector Pull-up • TTL Input Pull-down • TTL Unused Gate Pull-up 3 n-1 n "C" Profile MSM06C05 (M8340104xxxxxxH) MSM08C05 (M8340105xxxxxxH) MSM10C05 (M8340106xxxxxxH) The MSM06A05, MSM08A05, MSM10A05, MSM06C05, MSM08C05 and MSM10C05 molded single-in-line resistor networks provide the user with a choice of 4, 6 or 8 pair of R1/R2 resistor values for pulse squaring and TTL dual-line terminating requirements. PERFORMANCE TEST CONDITIONS MAX. ∆R (Typical Test Lots) Power Conditioning 1.5 x rated power, applied 1.5 hours “ON” and 0.5 hour “OFF” for 100 hours ± 4 hours at + 25°C ambient temperature ± 0.50% ∆R Thermal Shock 5 cycles between - 65°C and + 125°C ± 0.50% ∆R Short Time Overload 2.5 x rated working voltage 5 seconds ± 0.25% ∆R (Characteristic K) ± 0.50% ∆R (Characteristic M) Low Temperature Operation 45 minutes at full rated working voltage at - 65°C ± 0.25% ∆R (Characteristic K) ± 0.50% ∆R (Characteristic M) Moisture Resistance 240 hours with humidity ranging from 80% RH to 98% RH ± 0.50% ∆R Resistance to Soldering Heat Leads immersed in + 260°C solder to within 1/16" of body for 10 seconds ± 0.25% ∆R Shock Total of 18 shocks at 100 G's ± 0.25% ∆R Vibration 12 hours at maximum of 20 G's between 10 and 2,000 Hz ± 0.25% ∆R Load Life 1000 hours at + 70°C, rated power applied 1.5 hours “ON”, 0.5 hour “OFF” for full 1000 hour period ± 0.50% ∆R (Characteristic K) ± 2.00% ∆R (Characteristic M) Terminal Strength 4 1/2 pound pull for 30 seconds ± 0.25% ∆R Insulation Resistance 10,000 Megohm (minimum) — Dielectric Withstanding Voltage No evidence of arcing or damage (200 V RMS for 1 minute) — Document Number: 31514 Revision 10-Sep-04 For Technical Questions, contact: [email protected] www.vishay.com 79 www.vishay.com 80 Model Numbers Design Capabilities .. 82 Packaging and Mil ID..................84 Customized Resistor Networks Customer Specified Configurations • Isolated, Bussed or TTL-Terminator Circuits • High Packaging Density Product Design Capabilities Vishay Dale Multicomps, Custom Networks and Screened Substrates MULTIPLE COMPONENT MODULES (MULTICOMPS) CUSTOM NETWORKS AND SCREENED SUBSTRATES APPLICATIONS Vishay Dale has the extensive technical capability you need for your custom design requirements. • Reduce Component Count • Simplify Board Layout • Reduce Cross Talk • Filtering • Enhance Motherboard Performance www.vishay.com 82 Since all custom products are unique and actual performance may vary, some examples are given on the next page. When you are ready to submit your custom design for us to review, please call or fax us; or contact your local Vishay Dale representative. For Technical Questions, contact: [email protected] Document Number: 31528 Revision 23-Oct-00 Product Design Capabilities Multicomps, Custom Networks and Screened Substrates Vishay Dale SCHEMATICS MULTIPLE COMPONENT MODULES (MULTICOMPS) + CUSTOM NETWORKS +- + SCREENED SUBSTRATES FEATURES AND TYPICAL SPECIFICATIONS* ELECTRICAL SPECIFICATIONS - RESISTORS Thick Film Materials: Pd/Ag conductors, Ruthenium based cermet resistors, glass glazes, multi-layer dielectric systems, polymer protective coating. Thick Film Printing Techniques: Multi-layer printing, through-hole metallization, crossovers, double-sided designs. Substrate Material: 96% alumina. Substrate Thickness: 0.025" [0.635mm], 0.030" [0.762mm], 0.045" [1.143mm]. Thicker substrates for higher power applications available. SMT Devices: Inductors, diodes, thermistors, transistors, thin film resistors, integrated circuits. SMT Capacitors: Ceramic: X7R, COG. Capacitance = 10pF to 0.1µF ± 10% tolerance. Tantalum: Capacitance = .1µF to 100µF ± 10% tolerance. Package Configurations: SIP: 4 - 22 pins. Missing pins available. Maximum length, 2.2" [55.88mm]. Maximum height, 1.0" [25.4mm]. Lead length, 0.185" [4.699mm] maximum. Lead Spacing: 0.100" [2.54mm], SIP. 0.050" [1.27mm], SMT. Encapsulation Method: Conformal resin. Screened silicon insulator. Range: 10 ohm to 5 Megohm, standard. < 10 ohm, consult factory. Tolerance: 100 ohm to 1 Megohm: ± 1%, ± 2%. < 100 ohm: ± 2% or ± 1 ohm. > 1 Megohm: ± 5%, standard. Specials: Consult factory. Ratios: ± 0.5%, ± 1%. Specials: Consult factory. Temperature Coefficient (absolute): ± 200ppm/°C, standard. ± 100ppm/°C, special. TCR Tracking: ± 50ppm/°C (like values) and ± 100ppm/°C (mixed values). Operating Temperature: - 55°C to + 125°C, standard. - 55°C to + 150°C (consult factory). * Consult factory for possible exceptions to listed specifications. Document Number: 31528 Revision 23-Oct-00 ELECTRICAL SPECIFICATIONS - SCREENED CAPACITORS Capacitance: 33pF to 270pF. Other values, consult factory. Tolerance: ± 30%, standard. ± 20%, consult factory. Temperature Coefficient: ± 15%, standard. Dielectric Breakdown Voltage: 2.5 x rated voltage @ 5 seconds, standard. Rated Voltage: 25 volts maximum, standard. Operating Temperature: 0°C to + 70°C, standard. For Technical Questions, contact: [email protected] www.vishay.com 83 Packaging and MIL ID Vishay Dale PACKAGING DIMENSIONS in inches [millimeters] END-TO-END TUBE PACK DIMENSIONS SIP C D DIP DIP SMD A SIP Low Profile SIP High Profile C B A B C D 0.500 [12.70] 0.430 [10.92] 0.605 [15.37] 0.600 [15.24] 0.040 [1.02] 0.040 [1.02] — 22.25 [565.15] 23.50 [596.90] 23.50 [596.90] 0.120 [3.05] 0.120 [3.05] D B Typ. A Typ. D A SIDE-BY-SIDE SIP Side-By-Side SIP 10 PIN Flat Pack 8 PIN 6 PIN A D 4 PIN A 0.650 [16.51] 0.650 [16.51] 0.650 [16.51] 0.650 [16.51] 1.10 [27.94] 0.860 [21.84] 0.700 [17.78] 0.500 [12.70] — — — — 19 [482.60] 19 [482.60] 19 [482.60] 19 [482.60] FLAT PACK B B 8 [35.05] 1.38 [35.05] DFP D DFM 1.10 [27.94] 1.10 [27.94] — — 19.875 [504.82] 19.875 [504.82] STANDARD (•) AND OPTIONAL (X) PACKAGING MDM MDP RC MOLDED • • • DFM DFP Poly Bag X X Side-by-Side Magazine (Tube) X X End-to-End Magazine (Tube) SINGLE-IN-LINE FLAT PACKS DUAL-IN-LINE PACKAGING STYLES CSC MSM MSP X • • RC COATED RC MOLDED • • • X X Tape and Reel • End-To-End Magazine (Tube) Pack DIP/SIP: A magazine pack for single-in-line and dual-in-line resistor networks. Quantity per pack dependent on size of units. Maximum tube length is 23 1/2" [596.90mm]. Width and depth of tube dependent on size of individual resistor network. • Poly Bag: Units are packaged in poly bags and then packed in boxes. • Magazine (Tube) Pack Flat Pack: All flat packs are packaged in individual protective carriers that are considered as part of all flat pack units. Flat pack units are then packed in magazines (tubes). X Special Packaging: Military, antistatic and customer special packaging can be provided. Consult factory for information. MILITARY PART ORDERING EXAMPLES RESISTOR NETWORKS MIL-PRF-83401F (Type [RZ]) M8340101 M 1003 G A Vishay = Dale 1, 2 3 4 5 6 Type MDM 100k 4 2% 5 A NOTE: M 6 Characteristic. 1. Military Specification 2. Specification Sheet No. 3. Characteristic 4. Resistance Value 5. Tolerance 6. Schematic Resistance Value Examples Four Digit Figure 49R9 = 49.9 ohm, 1000 = 100 ohm 1001 = 1k ohm, 1004 = 1 Megohm Tolerance Examples F = ± 1.0% www.vishay.com 84 G = ± 2.0% J = ± 5.0% For Technical Questions, contact: [email protected] Document Number: 31532 Revision 23-Oct-00 Vishay www.vishay.com 85 Vishay www.vishay.com 86 WORLDWIDE SALES CONTACTS DISCRETE SEMICONDUCTORS AND PASSIVE COMPONENTS THE AMERICAS VISHAY AMERICAS ONE GREENWICH PLACE SHELTON, CT 06484 UNITED STATES PH: +1-402-563-6866 FAX: +1-402-563-6296 ASIA VISHAY INTERTECHNOLOGY ASIA PTE LTD. 25 TAMPINES STREET 92 KEPPEL BUILDING #02-00 SINGAPORE 528877 PH: +65-6788-6668 FAX: +65-6788-0988 JAPAN VISHAY JAPAN CO., LTD. GE EDISON BUILDING, SHIBUYA 3F 3-5-16 SHIBUYA SHIBUYA-KU TOKYO 150-0002 JAPAN PH: +81-3-5464-6411 FAX: +81-3-5464-6433 EUROPE VISHAY ELECTRONIC GMBH GEHEIMRAT-ROSENTHAL-STR. 100 95100 SELB GERMANY PH: +49-9287-71-0 FAX: +49-9287-70435 VISHAY S.A. 4, RUE DE SALONIQUE 95101 ARGENTEUIL FRANCE PH: +33-1-39-98-22-00 FAX: +33-1-39-98-22-05 VISHAY LTD. PALLION INDUSTRIAL ESTATE SUNDERLAND, SR4 6SU GREAT BRITAIN PH: +44-191-514-4155 FAX: +44-191-567-8262 ONLINE INFORMATION For product information and a current list of sales offices, representatives and distributors, visit our website: www.vishay.com ONE OF THE WORLD’S LARGEST MANUFACTURERS OF DISCRETE SEMICONDUCTORS AND PASSIVE COMPONENTS V I S H A Y I N T E R T E C H N O L O G Y, I N C . World Headquarters 63 Lincoln Highway Malvern, PA 19355-2143 United States w w w. v i s h a y. c o m © C o p y r i g h t V i s h a y I n t e r t e c h n o l o g y, I n c. R e g i s t e r e d Tr a d e m a r k s o f V i s h a y I n t e r t e c h n o l o g y, I n c. All rights reserved. Printed in the United States. Specifications subject to change without notice. Databook VSD-DB0011-0410