datasheet

Board 2S SKYPER 32 R Gold
Absolute Maximum Ratings
SKYPER®
Adaptor board
Symbol
Conditions
Vs
Supply voltage primary
16
V
IoutPEAK
Output peak current
15
A
IoutAVmax
Output average current
50
mA
fmax
Max. switching frequency
50
kHz
VCE
Collector emitter voltage sense across
the IGBT
1700
V
4000
V
1200
V
1500
V
Visol IO
VisolPD
Visol12
Values
Insulation test voltage input - output
(AC, rms, 2s)
Partial discharge extinction voltage,
rms, QPD ≤ 10pC
Isolation test voltage output 1 - output 2
(AC, rms, 2s)
Unit
RGon min
Minimum rating for external RGon
1.5
Minimum rating for external RGoff
Ω
RGoff min
1.5
Ω
Top
Operating temperature
-40 ... 85
°C
Features
Tstg
Storage temperature
-40 ... 85
°C
• Two output channels
• Gold nickel finish
• Failure management
Characteristics
Symbol
Conditions
min.
typ.
max.
Unit
Typical Applications*
Vs
Supply voltage primary side
14.4
15
15.6
V
Vi
Input signal voltage on / off
VIT+
Input treshold voltage HIGH
12.3
V
VIT-
Input threshold voltage (LOW)
VG(on)
Turn on output voltage
VG(off)
Turn off output voltage
-7
V
td(on)IO
Input-output turn-on propagation time
1.1
µs
td(off)IO
Input-output turn-off propagation time
1.1
µs
Board 2S SKYPER 32 R Gold
Preliminary Data
• Adaptor board for SKYPER 32 IGBT
drivers in bridge circuits for industrial
applications
• PCB with gold plating
• DC bus up to 1000V
Footnotes
with external high voltage diode
Please Note: the isolation test is not
performed as a series test at SEMIKRON
and must be performed by the user
according to VDE 0110-20
can be expanded to 6,3µQ with boost
capacitors
15 / 0
4.6
V
V
15
V
Isolation coordination in compliance with
EN50178 PD2
Operating temperature is real ambient
temperature around the driver core
Degree of protection: IP00
Adaptor board
© by SEMIKRON
Rev. 1.0 – 08.12.2015
1
Board 2S SKYPER 32 R Gold
This is an electrostatic discharge sensitive device (ESDS), international standard IEC 60747-1, chapter IX.
*IMPORTANT INFORMATION AND WARNINGS
The specifications of SEMIKRON products may not be considered as guarantee or assurance of product characteristics
("Beschaffenheitsgarantie"). The specifications of SEMIKRON products describe only the usual characteristics of products to be expected in
typical applications, which may still vary depending on the specific application. Therefore, products must be tested for the respective
application in advance. Application adjustments may be necessary. The user of SEMIKRON products is responsible for the safety of their
applications embedding SEMIKRON products and must take adequate safety measures to prevent the applications from causing a physical
injury, fire or other problem if any of SEMIKRON products become faulty. The user is responsible to make sure that the application design is
compliant with all applicable laws, regulations, norms and standards. Except as otherwise explicitly approved by SEMIKRON in a written
document signed by authorized representatives of SEMIKRON, SEMIKRON products may not be used in any applications where a failure of
the product or any consequences of the use thereof can reasonably be expected to result in personal injury. No representation or warranty is
given and no liability is assumed with respect to the accuracy, completeness and/or use of any information herein, including without limitation,
warranties of non-infringement of intellectual property rights of any third party. SEMIKRON does not assume any liability arising out of the
applications or use of any product; neither does it convey any license under its patent rights, copyrights, trade secrets or other intellectual
property rights, nor the rights of others. SEMIKRON makes no representation or warranty of non-infringement or alleged non-infringement of
intellectual property rights of any third party which may arise from applications. Due to technical requirements our products may contain
dangerous substances. For information on the types in question please contact the nearest SEMIKRON sales office. This document
supersedes and replaces all information previously supplied and may be superseded by updates. SEMIKRON reserves the right to make
changes.
2
Rev. 1.0 – 08.12.2015
© by SEMIKRON