TECHNICAL DATA IL5009 Speaker Amplifier The IL5009 is a monolithic integrated circuit designed forspeaker amp. FEATURES • Operating supply voltage range : Vcc = 1.5V ~ 5.0V • Recommended operating supply voltage : Vcc = 3V • Low quiescent : Icc = 3.9mA • Package is compact. ORDERING INFORMATION IL5009N Plastic IL5009D SOIC TA = -20 to 60 C for all package APPLICATION • Telephone set MAXIMUM RATINGS Characteristics Supply Voltage Power Dissipation Operating Temperature Storage Temperature Symbol Rating Unit Vcc PD Topr Tstr 10 800 -20 ~ +60 -55 ~ +150 V mW ºC ºC * Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. BLOCK DIAGRAM & APPLICATION CIRCUIT 2011, February Ver. 01 IL5009 ELECTRICAL DC CHARACTERISTICS (Pin Voltage at Vcc = 3V and no input signal) Pin No. Symbol Typical Value Unit Pin No Symbol Typical Value Unit 1 V1 1.4 V 5 V5 0 V 2 V2 1.4 V 6 V6 1.5 V 3 V3 1.4 V 7 V7 2.3 V 4 V4 1.3 V 8 V8 3.0 V ELECTRICAL AC CHARACTERISTICS ( Unless otherwise specified, Vcc = 3V, f = 1KHz, VIN = 20mVrms, RL = 32Ω, Ta = 25 ºC ) Characteristic Quiescent Current Symbol Test condition Min. Typ. Max. Unit ICCO1 Vcc = 1.5V 3.1 mA ICCO2 Vcc = 3.0V 3.9 mA ICCO3 Vcc = 5.0V 4.9 mA 27 dB Close Loop Voltage Gain GV Maximum Output Voltage VOM THD = 10% 1.0 Vrms Total Harmonic Distortion THD VIN = 40m Vrms 0.6 % Output noise Voltage VNO VIN = 0 200 Vrms Input Resistance RIN 15 KΩ TYPICAL PERFORMANCE CHARACTERISTICS 2011, February Ver. 01 IL5009 N SUFFIX PLASTIC DIP (MS – 001BA) A Dimension, mm 5 8 B 1 4 F Symbol MIN MAX A 8.51 10.16 B 6.1 7.11 C L C 5.33 D 0.36 0.56 F 1.14 1.78 -T- SEATING PLANE N G M K 0.25 (0.010) M J H D T NOTES: 1. Dimensions “A”, “B” do not include mold flash or protrusions. Maximum mold flash or protrusions 0.25 mm (0.010) per side. G 2.54 H 7.62 J 0° 10° K 2.92 3.81 L 7.62 8.26 M 0.2 0.36 N 0.38 D SUFFIX SOIC (MS - 012AA) Dimension, mm A 8 5 B H 1 G P 4 D K MIN MAX A 4.8 5 B 3.8 4 C 1.35 1.75 D 0.33 0.51 F 0.4 1.27 R x 45 C -T- Symbol SEATING PLANE J F 0.25 (0.010) M T C M NOTES: 1. Dimensions A and B do not include mold flash or protrusion. 2. Maximum mold flash or protrusion 0.15 mm (0.006) per side for A; for B ‑ 0.25 mm (0.010) per side. M G 1.27 H 5.72 J 0° 8° K 0.1 0.25 M 0.19 0.25 P 5.8 6.2 R 0.25 0.5 2011, February Ver. 01