HMC130


Design Assistance

Customised Pack Sizes / Qtys

Assembly Assistance

Support for all industry recognised
supply formats:

Die handling consultancy

Hi-Rel die qualification

Hot & Cold die probing

Electrical test & trimming
o Waffle Pack
o Gel Pak
o Tape & Reel

Onsite storage, stockholding &
scheduling

100% Visual Inspection
o MIL-STD 883 Condition A
o MIL-STD 883 Condition A

On-site failure analysis

Bespoke 24 Hour monitored
storage systems for secure long
term product support

On-site failure analysis
Contact
[email protected]
For price, delivery and to place orders
HMC130
www.analog.com
www.micross.com
Analog Devices Welcomes
Hittite Microwave Corporation
NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
www.analog.com
www.hittite.com
THIS PAGE INTENTIONALLY LEFT BLANK
HMC130
v04.1007
GaAs MMIC DOUBLE-BALANCED
MIXER, 6 - 11 GHz
Typical Applications
Features
The HMC130 is ideal for:
Conversion Loss: 7 dB
• Microwave & VSAT Radios
LO to RF and IF Isolation: >32 dB
• Test Equipment
Input IP3: +17 dBm
• Military EW, ECM, C3I
No DC Bias Required
• Space Telecom
Die Size: 1.45 x 1.3 x 0.1 mm
Functional Diagram
General Description
MIXERS - DOUBLE-BALANCED - CHIP
4
The HMC130 chip is a miniature double-balanced
mixer which can be used as an upconverter or downconverter in the 6 to 11 GHz band. The chip can be
integrated directly into hybrid MMIC’s without DC bias
or external baluns to provide an extremely compact
mixer. It is ideally suited for applications where small
size, no DC Bias, and consistent IC performance are
required. This mixer can operate over a wide LO drive
input of +9 to +15 dBm. It performs equally well as a
Bi-Phase modulator or demodulator. See HMC137
data sheet.
Electrical Specifi cations, TA = +25° C, LO Drive = +15 dBm
Parameter
Min.
Typ.
Frequency Range, RF & LO
6.0 - 11.0
Frequency Range, IF
DC - 2.0
Max.
GHz
GHz
Conversion Loss
7
9
dB
Noise Figure (SSB)
7
9
dB
LO to RF Isolation
32
40
LO to IF Isolation
35
40
dB
IP3 (Input)
13
17
dBm
IP2 (Input)
45
55
dBm
1 dB Gain Compression (Input)
6
9
dBm
* Unless otherwise noted, all measurements performed as downconverter, IF = 100 MHz
4 - 14
Units
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
dB
HMC130
v04.1007
GaAs MMIC DOUBLE-BALANCED
MIXER, 6 - 11 GHz
Conversion Gain vs. Temperature
@ LO = +15 dBm
Isolation @ LO = +15 dBm
0
-10
ISOLATION (dB)
CONVERSION GAIN (dB)
-15
-5
-10
+25 C
+85 C
-55 C
-15
-20
-25
RF/IF
LO/RF
LO/IF
-30
-35
4
-40
-20
-50
5
6
7
8
9
10
FREQUENCY (GHz)
11
12
13
Conversion Gain vs. LO Drive
5
8
9
10
FREQUENCY (GHz)
11
12
13
0
RETURN LOSS (dB)
CONVERSION GAIN (dB)
7
Return Loss @ LO = +15 dBm
0
-5
-10
+9 dBm
+11 dBm
+13 dBm
+15 dBm
-15
-5
-10
-15
LO
RF
-20
-20
-25
5
6
7
8
9
10
FREQUENCY (GHz)
11
12
13
4
5
6
7
8
9
10
Frequency (GHz)
11
12
13
14
Upconverter Performance
Conversion Gain vs. LO Drive
IF Bandwidth @ LO = +15 dBm
0
CONVERSION GAIN (dB)
0
RESPONSE (dB)
6
-5
-10
IF CONVERSION LOSS
IF RETURN LOSS (dB)
-15
-20
-5
MIXERS - DOUBLE-BALANCED - CHIP
-45
-10
+9 dBm
+11 dBm
+13 dBm
+15 dBm
-15
-20
0
0.5
1
1.5
2
2.5
FREQUENCY (GHz)
3
3.5
4
5
6
7
8
9
10
FREQUENCY (GHz)
11
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
12
13
4 - 15
HMC130
v04.1007
GaAs MMIC DOUBLE-BALANCED
MIXER, 6 - 11 GHz
Input IP3 vs.
Temperature @ LO = +15 dBm
Input IP3 vs. LO Drive
30
30
+11 dBm
+13 dBm
+15 dBm
20
15
10
5
6
7
8
9
10
FREQUENCY (GHz)
11
12
4
13
6
7
8
9
10
11
12
13
Input IP2 vs.
Temperature @ LO = +15 dBm
Input IP2 vs. LO Drive
80
80
75
75
+11 dBm
+13 dBm
+15 dBm
70
+25 C
+85 C
-55 C
70
65
IP2 (dBm)
IP2 (dBm)
5
FREQUENCY (GHz)
60
55
65
60
55
50
50
45
45
40
40
5
6
7
8
9
10
FREQUENCY (GHz)
11
12
13
Input P1dB vs.
Temperature @ LO = +15 dBm
5
6
7
8
9
10
FREQUENCY (GHz)
11
12
13
Harmonics of LO
13
nLO Spur @ RF Port
12
+25 C
+85 C
-55 C
11
10
9
LO Freq. (GHz)
1
2
3
6
7
8
9
10
11
FREQUENCY (GHz)
12
4
9.0
45
56
46
79
10.5
42
56
56
62
12.0
36
54
43
60
13.5
35
69
38
57
15.0
35
58
44
?
16.5
32
49
40
?
LO = +13 dBm
All values in dBc below input LO level measured at RF port
8
4 - 16
20
15
10
P1dB (dBm)
MIXERS - DOUBLE-BALANCED - CHIP
4
+25 C
+85 C
-55 C
25
IP3 (dBm)
IP3 (dBm)
25
13
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC130
v04.1007
GaAs MMIC DOUBLE-BALANCED
MIXER, 6 - 11 GHz
Absolute Maximum Ratings
MxN Spurious @ IF Port
nLO
mRF
0
1
2
3
4
0
xx
17.16
26.0
9.0
37.33
1
12.83
0
39.83
53.0
33.66
2
69.0
76.5
57.83
76.83
71.0
3
75.33
76.16
78
61.66
78.16
4
66.83
74.83
77.33
78.16
79.66
LO Drive
+27 dBm
Storage Temperature
-65 to +150 °C
Operating Temperature
-55 to +85 °C
%,%#42/34!4)#3%.3)4)6%$%6)#%
/"3%26%(!.$,).'02%#!54)/.3
4
MIXERS - DOUBLE-BALANCED - CHIP
RF Freq. = 9.1 GHz @ -10 dBm
LO Freq. = 9.0 GHz @ +13 dBm
Measured as downconverter
Outline Drawing
Die Packaging Information [1]
Standard
Alternate
WP-3 (Waffle Pack)
[2]
[1] Refer to the “Packaging Information” section for die
packaging dimensions.
[2] For alternate packaging information contact Hittite
Microwave Corporation.
NOTES:
1. ALL DIMENSIONS ARE IN INCHES [MM]
2. BOND PADS ARE .004” SQUARE
3. TYPICAL BOND PAD SPACING CENTER TO CENTER
.1 IS .006” EXCEPT AS SHOWN
4. DIE THICKNESS = .004” [.100 MM]
5. BACKSIDE METALIZATION: GOLD
6. BACKSIDE METAL IS GROUND
7. BOND PAD METALIZATION: GOLD
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
4 - 17
HMC130
v04.1007
GaAs MMIC DOUBLE-BALANCED
MIXER, 6 - 11 GHz
Pad Descriptions
Pad Number
Function
Description
1
RF
This pin is DC coupled
and matched to 50 Ohms.
2
LO
This pin is DC coupled
and matched to 50 Ohms.
IF
This pin is DC coupled. For applications not requiring operation to DC, this port should be DC blocked externally using
a series capacitor whose value has been chosen to pass
the necessary IF frequency range. For operation to DC this
pin must not source or sink more than 2mA of current or die
non-function and possible die failure will result.
GND
The backside of the die must connect to RF ground.
Interface Schematic
MIXERS - DOUBLE-BALANCED - CHIP
4
4 - 18
3
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC130
v04.1007
GaAs MMIC DOUBLE-BALANCED
MIXER, 6 - 11 GHz
Assembly Diagram
Handling Precautions
Follow these precautions to avoid permanent damage.
Storage: All bare die are placed in either Waffle or Gel based ESD protective containers, and then sealed in an ESD protective bag
for shipment. Once the sealed ESD protective bag has been opened, all die should be stored in a dry nitrogen environment.
Cleanliness: Handle the chips in a clean environment. DO NOT attempt to clean the chip using liquid cleaning systems.
Static Sensitivity: Follow ESD precautions to protect against ESD strikes.
Transients: Suppress instrument and bias supply transients while bias is applied. Use shielded signal and bias cables to minimize
inductive pick-up.
General Handling: Handle the chip along the edges with a vacuum collet or with a sharp pair of bent tweezers. The surface of the
chip has fragile air bridges and should not be touched with vacuum collet, tweezers, or fingers.
Mounting
MIXERS - DOUBLE-BALANCED - CHIP
4
The chip is back-metallized and can be die mounted with AuSn eutectic preforms or with electrically conductive epoxy. The mounting
surface should be clean and flat.
Eutectic Die Attach: A 80/20 gold tin preform is recommended with a work surface temperature of 255 °C and a tool temperature
of 265 °C. When hot 90/10 nitrogen/hydrogen gas is applied, tool tip temperature should be 290 °C. DO NOT expose the chip
to a temperature greater than 320 °C for more than 20 seconds. No more than 3 seconds of scrubbing should be required for
attachment.
Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed around the
perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule.
Wire Bonding
Ball or wedge bond with 0.025 mm (1 mil) diameter pure gold wire. Thermosonic wirebonding with a nominal stage temperature of
150 °C and a ball bonding force of 40 to 50 grams or wedge bonding force of 18 to 22 grams is recommended. Use the minimum
level of ultrasonic energy to achieve reliable wirebonds. Wirebonds should be started on the chip and terminated on the package or
substrate. All bonds should be as short as possible <0.31 mm (12 mils).
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
4 - 19