HMC558


Design Assistance

Customised Pack Sizes / Qtys

Assembly Assistance

Support for all industry recognised
supply formats:

Die handling consultancy

Hi-Rel die qualification

Hot & Cold die probing

Electrical test & trimming
o Waffle Pack
o Gel Pak
o Tape & Reel

Onsite storage, stockholding &
scheduling

100% Visual Inspection
o MIL-STD 883 Condition A
o MIL-STD 883 Condition A

On-site failure analysis

Bespoke 24 Hour monitored
storage systems for secure long
term product support

On-site failure analysis
Contact
[email protected]
For price, delivery and to place orders
HMC558
www.analog.com
www.micross.com
Analog Devices Welcomes
Hittite Microwave Corporation
NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
www.analog.com
www.hittite.com
THIS PAGE INTENTIONALLY LEFT BLANK
HMC558
v01.1007
GaAs MMIC FUNDAMENTAL
MIXER, 5.5 - 14 GHz
Typical Applications
Features
The HMC558 is ideal for:
High LO/RF Isolation: 45 dB
• Microwave Radio
Passive Double Balanced Topology
• Military & Space
Low Conversion Loss: 7 dB
• Communications, Radar & EW
Wide IF Bandwidth: DC - 6 GHz
• Test Equipment & Sensors
Small Size: 0.91 x 0.94 x 0.1 mm
Functional Diagram
General Description
MIXERS - DOUBLE-BALANCED - CHIP
4
The HMC558 is a passive double balanced mixer
that can be used as an upconverter or downconverter
between 5.5 and 14 GHz. The miniature monolithic
mixer is fabricated in a GaAs MESFET process, and
requires no external components or matching circuitry. The HMC558 operates with LO drive levels as
low as +9 dBm and provides excellent LO to RF and
LO to IF isolation due to optimized balun structures.
Measurements were made with the chip mounted
into in a 50 ohm test fixture and includes the parasitic effects of wire bond assembly. Connections were
made with a 1 mil wire bond with minimal length (<12
mil).
Electrical Specifi cations, TA = +25° C, IF= 100 MHz, LO= +15 dBm*
Parameter
Min.
Frequency Range, RF & LO
Frequency Range, IF
Typ.
Max.
Min.
Typ.
Max.
5.5 - 10.0
10.0 - 14.0
GHz
DC - 6
DC - 6
GHz
Conversion Loss
7
9.5
8.5
10
dB
Noise Figure (SSB)
7
9.5
8.5
10
dB
LO to RF Isolation
35
45
30
36
dB
LO to IF Isolation
20
25
20
25
dB
RF to IF Isolation
8
14
10
16
dB
IP3 (Input)
20
24
dBm
IP2 (Input)
54
46
dBm
1 dB Gain Compression (Input)
11
13
dBm
*Unless otherwise noted, all measurements performed as downconverter, IF= 100 MHz.
4 - 72
Units
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC558
v01.1007
GaAs MMIC FUNDAMENTAL
MIXER, 5.5 - 14 GHz
Conversion Gain vs.
Temperature @ LO = +15 dBm
Isolation @ LO = +15 dBm
0
-10
-5
-10
-20
-30
RF/IF
LO/RF
LO/IF
-50
-20
-60
4
6
8
10
12
14
16
4
6
FREQUENCY (GHz)
10
12
14
16
14
16
14
16
Return Loss @ LO = +15 dBm
0
0
-5
-4
RETURN LOSS (dB)
CONVERSION GAIN (dB)
8
FREQUENCY (GHz)
Conversion Gain vs. LO Drive
-8
+9 dBm
+12 dBm
+15 dBm
+18 dBm
+20 dBm
-12
-10
-15
RF
LO
-20
-25
-16
4
6
8
10
12
14
16
4
6
8
10
12
FREQUENCY (GHz)
FREQUENCY (GHz)
Upconverter Performance
Conversion Gain vs. LO Drive
IF Bandwidth @ LO = +15 dBm
0
0
CONVERSION GAIN (dB)
IF RETURN LOSS
CONVERSION GAIN
-5
RESPONSE (dB)
4
-40
-15
-10
-15
-20
-4
-8
+12 dBm
+15 dBm
+18 dBm
+20 dBm
-12
-25
-30
MIXERS - DOUBLE-BALANCED - CHIP
ISOLATION (dB)
CONVERSION GAIN (dB)
0
-16
0
1
2
3
4
FREQUENCY (GHz)
5
6
7
4
6
8
10
12
FREQUENCY (GHz)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
4 - 73
HMC558
v01.1007
GaAs MMIC FUNDAMENTAL
MIXER, 5.5 - 14 GHz
Input IP3 vs.
Temperature @ LO = +15 dBm *
Input IP3 vs. LO Drive *
30
30
25
25
20
15
+25C
+85C
-55C
10
+9 dBm
+12 dBm
+15 dBm
+18 dBm
+20 dBm
15
5
10
0
5
7
9
11
13
15
5
7
FREQUENCY (GHz)
60
60
50
50
IP2 (dBm)
IP2 (dBm)
70
40
30
+9 dBm
+12 dBm
+15 dBm
+18 dBm
+20 dBm
10
11
13
15
13
15
3
4
Input IP2 vs.
Temperature @ LO = +15 dBm *
70
20
9
FREQUENCY (GHz)
Input IP2 vs. LO Drive *
40
30
+25C
+85C
-55C
20
10
0
0
5
7
9
11
13
15
5
7
FREQUENCY (GHz)
9
11
FREQUENCY (GHz)
Input P1dB vs.
Temperature @ LO = +15 dBm
MxN Spurious Outputs
16
nLO
14
P1dB (dBm)
MIXERS - DOUBLE-BALANCED - CHIP
4
IP3 (dBm)
IP3 (dBm)
20
12
10
+25C
+85C
-55C
8
mRF
0
1
2
0
xx
-10
22
18
28
1
9
0
24
52
50
2
87
48
65
49
79
3
90
92
77
76
81
4
86
92
92
96
108
RF = 8.1 GHz @ -10 dBm
LO = 8 GHz @ +15 dBm
All values in dBc below the IF output power level.
6
5
7
9
11
13
15
FREQUENCY (GHz)
* Two-tone input power = -10 dBm each tone, 1 MHz spacing.
4 - 74
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC558
v01.1007
GaAs MMIC FUNDAMENTAL
MIXER, 5.5 - 14 GHz
Absolute Maximum Ratings
RF / IF Input
+25 dBm
LO Drive
+25 dBm
Channel Temperature
150 °C
Continuous Pdiss (T = 85 °C)
(derate 7.6 mW/°C above 85 °C)
492 mW
Thermal Resistance
(channel to die bottom)
132 °C/W
Storage Temperature
-65 to +150 °C
Operating Temperature
-55 to +85 °C
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
4
MIXERS - DOUBLE-BALANCED - CHIP
Outline Drawing
Die Packaging Information
[1]
NOTES:
1. ALL DIMENSIONS ARE IN INCHES [MM].
Standard
Alternate
WP-15 (Waffle Pack)
[2]
[1] Refer to the “Packaging Information” section for die
packaging dimensions.
[2] For alternate packaging information contact Hittite
Microwave Corporation.
2. DIE THICKNESS IS .004”.
3. TYPICAL BOND PAD IS .004” SQUARE.
4. BOND PAD SPACING CENTER TO CENTER IS .006”.
5. BACKSIDE METALLIZATION: GOLD.
6. BOND PAD METALLIZATION: GOLD.
7. BACKSIDE METAL IS GROUND.
8. CONNECTION NOT REQUIRED FOR UNLABELED BOND PADS.
9. THIS DIE IS DESIGNED FOR PICK-UP WITH VACUUM (EDGE)
COLLET TOOLS. TO PRECLUDE THE RISK OF PERMANENT
DAMAGE, NO CONTACT TO THE DIE SURFACE IS ALLOWED
WITHIN THIS RECTANGULAR AREA.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
4 - 75
HMC558
v01.1007
GaAs MMIC FUNDAMENTAL
MIXER, 5.5 - 14 GHz
Pad Descriptions
MIXERS - DOUBLE-BALANCED - CHIP
4
4 - 76
Pad Number
Function
Description
1
LO
This pin is DC coupled
and matched to 50 Ohms.
2
RF
This pin is DC coupled
and matched to 50 Ohms.
3
IF
This pad is DC coupled. For applications not requiring
operation to DC, this port should be DC blocked externally
using a series capacitor whose value has been chosen to
pass the necessary IF frequency range. For operation to DC,
this pin must not source or sink more than 2 mA of current or
part non-function and possible part failure will result.
Die Bottom
GND
Die bottom must be connected to RF/DC ground.
Interface Schematic
Assembly Drawing
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC558
v01.1007
GaAs MMIC FUNDAMENTAL
MIXER, 5.5 - 14 GHz
Mounting & Bonding Techniques for Millimeterwave GaAs MMICs
50 Ohm Microstrip transmission lines on 0.127mm (5 mil) thick alumina thin film
substrates are recommended for bringing RF to and from the chip (Figure 1). If
0.254mm (10 mil) thick alumina thin film substrates must be used, the die should
be raised 0.150mm (6 mils) so that the surface of the die is coplanar with the surface
of the substrate. One way to accomplish this is to attach the 0.102mm (4 mil) thick
die to a 0.150mm (6 mil) thick molybdenum heat spreader (moly-tab) which is then
attached to the ground plane (Figure 2).
0.102mm (0.004”) Thick GaAs MMIC
3 mil Ribbon Bond
0.076mm
(0.003”)
RF Ground Plane
Microstrip substrates should be brought as close to the die as possible in order to
minimize ribbon bond length. Typical die-to-substrate spacing is 0.076mm (3 mils).
Gold ribbon of 0.075 mm (3 mil) width and minimal length <0.31 mm (<12 mils) is
recommended to minimize inductance on RF, LO & IF ports.
0.127mm (0.005”) Thick Alumina
Thin Film Substrate
Figure 1.
Handling Precautions
Follow these precautions to avoid permanent damage.
Storage: All bare die are placed in either Waffle or Gel based ESD protective
containers, and then sealed in an ESD protective bag for shipment. Once the
sealed ESD protective bag has been opened, all die should be stored in a dry
nitrogen environment.
Cleanliness: Handle the chips in a clean environment. DO NOT attempt to clean
the chip using liquid cleaning systems.
Static Sensitivity: Follow ESD precautions to protect against ESD strikes.
Transients: Suppress instrument and bias supply transients while bias is applied.
Use shielded signal and bias cables to minimize inductive pick-up.
General Handling: Handle the chip along the edges with a vacuum collet or with
a sharp pair of bent tweezers. The surface of the chip has fragile air bridges and
should not be touched with vacuum collet, tweezers, or fingers.
Mounting
0.102mm (0.004”) Thick GaAs MMIC
3 mil Ribbon Bond
0.076mm
(0.003”)
RF Ground Plane
0.150mm (0.005”) Thick
Moly Tab
0.254mm (0.010”) Thick Alumina
Thin Film Substrate
Figure 2.
The chip is back-metallized and can be die mounted with AuSn eutectic preforms
or with electrically conductive epoxy. The mounting surface should be clean and flat.
Eutectic Die Attach: A 80/20 gold tin preform is recommended with a work surface temperature of 255 °C and a tool temperature
of 265 °C. When hot 90/10 nitrogen/hydrogen gas is applied, tool tip temperature should be 290 °C. DO NOT expose the chip
to a temperature greater than 320 °C for more than 20 seconds. No more than 3 seconds of scrubbing should be required for
attachment.
Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed around the
perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule.
Wire Bonding
Ball or wedge bond with 0.025 mm (1 mil) diameter pure gold wire is recommended. Thermosonic wirebonding with a nominal stage
temperature of 150 °C and a ball bonding force of 40 to 50 grams or wedge bonding force of 18 to 22 grams is recommended. Use
the minimum level of ultrasonic energy to achieve reliable wirebonds. Wirebonds should be started on the chip and terminated on
the package or substrate. All bonds should be as short as possible <0.31 mm (12 mils).
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
4
MIXERS - DOUBLE-BALANCED - CHIP
The die should be attached directly to the ground plane eutectically or with
conductive epoxy (see HMC general Handling, Mounting, Bonding Note).
4 - 77