w 1171-EV2-REV2 Quick Start Guide DOC TYPE: EXAMPLE CONFIGURATIONS BOARD REFERENCE: 1171-EV2-REV2 BOARD TYPE: Customer Main Board WOLFSON DEVICE(S): WM8903 DATE: July 2014 DOC REVISION: 1.1 INTRODUCTION The 1171-EV2-REV2 customer evaluation board provides a complete hardware platform for evaluation of all the mini boards with analogue WM71x0 and digital WM72x0. Configurations covered are listed below: Analogue microphone bypass to headphones output (full analogue path) Analogue microphone recording with ADC. Analogue microphone loopback via the ADC and DAC with headphone output Digital Microphone recording with ADC. Digital microphone loopback via the ADC and DAC with headphone output. Supports mono or stereo microphones (digital or analogue microphone and not together) Differential and single ended PGA circuit configuration, volume, boost and mute controls. This document should be used as a starting point for evaluation of WM7xx0 but it will not cover every possible configuration. Assumptions: 1. The user is familiar with the WM7xx0 boards (see relevant documents below). 2. The user has set up WISCE as per instructions and is controlling the WM8903. Related documents: 1. WM8903_Rev3.1.pdf 2. WISCE Quick Start Guide.pdf 3. WM7xx0 example configurations and schematic. 4. 1171-EV2-REV2 Schematic Layout.pdf WOLFSON MICROELECTRONICS plc July 2014, Rev 1.1 Copyright 2014 Wolfson Microelectronics plc 1171-EV2-REV2 Customer Information TABLE OF CONTENTS INTRODUCTION ............................................................................................................. 1 TABLE OF CONTENTS .................................................................................................. 2 BLOCK DIAGRAM ......................................................................................................... 3 STARTUP ....................................................................................................................... 3 CONNECTION DIAGRAM........................................................................................................... 4 I/O TABLE .................................................................................................................................... 4 TECHNICAL SUPPORT ................................................................................................. 6 IMPORTANT NOTICE .................................................................................................... 7 ADDRESS:................................................................................................................................... 7 w Customer Information July 2014, Rev 1.1 2 1171-EV2-REV2 Customer Information BLOCK DIAGRAM Figure 1 1171-EV2 Block Diagram STARTUP The analogue or digital microphones are inserted into the microphone left (J6) and right (J7) slots with acoustic port hole facing to the edge of the board. The 1171_EV2 Customer Board is powered and controlled via USB (J2) by a laptop with WISCE Quick Start Panel shown in Figure 2 Quick Start Panel on WISCE. Figure 2 Quick Start Panel on WISCE w Customer Information July 2014, Rev 1.1 3 1171-EV2-REV2 Customer Information CONNECTION DIAGRAM Figure 3 below shows the external connections on the1171-EV2-REV2. Further details can be found on the schematic layout referenced at the start of the document. Please refer to the Table 1 for further detail on external I/O connections. USB SPDIF input for audio playback (optional) SPDIF OUTPUT for recording Headphone output for loopback and bypass path Microphone slots for microphone mini boards, keep acoustic port hole facing out to the edge Figure 3 Board Setup I/O TABLE SIGNAL BOARD REFERENCE IMPORTANT NOTES Microphone Input slot LINPUT1 J6 : PIN1 Analogue microphone input LINPUT2 J6 : PIN7 Analogue microphone input DMIC_DAT Digital Microphone Data, the signal should swing between DGND and DBVDD. RINPUT1 J6 : PIN4 J7 : PIN4 J6 : PIN5 J7 : PIN4 J7 : PIN1 Analogue microphone input RINPUT2 J7 : PIN7 Analogue microphone input DMIC_CLK Digital Microphone CLK. The signals should swing between DGND and DBVDD. Ground GND Common ground, TP1, TP2, TP6 Common ground plane. Audio Interface ADCDAT H1: PIN 18 MCLK H1: PIN 14 DACDAT H1: PIN 10 BCLK H1: PIN 6 LRCLK HI : PIN 2 Control and Power USB w Customer Information J2 All audio interface signals should swing between DGND and DBVDD. +5V Power and control interface to setup the path July 2014, Rev 1.1 4 1171-EV2-REV2 Customer Information SIGNAL BOARD REFERENCE IMPORTANT NOTES Digital Audio SPDIF IN U4 Digital Audio for DAC playback and SPDIF MCLK source. The input format is standard TOSLINK digital interface commonly available on many sound card or consumer product. This SPDIF OUT U6 Digital Audio for ADC recording of digital or analogue microphone. The output format is SPDIF and can be connected to any PC sound card or test equipment which supports the standard TOSLINK digital interface. This interface is common on many sound card interfaces. Line Inputs LINEL J4 : PIN 2 LINER J4 : PIN 3 Optional analogue line input. Analogue Outputs HPOUTR HPOUTL HPGND J3 : PIN3 J3 : PIN2 Common ground Ground referenced headphone output supports the connection of standard 16 or 32 ohms via the 3.5mm jack socket, line level loads or test equipment may also be connected to this output. Table 1 I/O Configurations w Customer Information July 2014, Rev 1.1 5 1171-EV2-REV2 Customer Information TECHNICAL SUPPORT If you require more information or require technical support, please contact the nearest Wolfson Microelectronics regional office: http://www.wolfsonmicro.com/contact or one of our global distributors: http://www.wolfsonmicro.com/distribution w Customer Information July 2014, Rev 1.1 6 Customer Information 1171-EV2-REV2 IMPORTANT NOTICE Wolfson Microelectronics plc (“Wolfson”) products and services are sold subject to Wolfson’s terms and conditions of sale, delivery and payment supplied at the time of order acknowledgement. Wolfson warrants performance of its products to the specifications in effect at the date of shipment. Wolfson reserves the right to make changes to its products and specifications or to discontinue any product or service without notice. Customers should therefore obtain the latest version of relevant information from Wolfson to verify that the information is current. Testing and other quality control techniques are utilised to the extent Wolfson deems necessary to support its warranty. Specific testing of all parameters of each device is not necessarily performed unless required by law or regulation. In order to minimise risks associated with customer applications, the customer must use adequate design and operating safeguards to minimise inherent or procedural hazards. Wolfson is not liable for applications assistance or customer product design. The customer is solely responsible for its selection and use of Wolfson products. Wolfson is not liable for such selection or use nor for use of any circuitry other than circuitry entirely embodied in a Wolfson product. Wolfson’s products are not intended for use in life support systems, appliances, nuclear systems or systems where malfunction can reasonably be expected to result in personal injury, death or severe property or environmental damage. Any use of products by the customer for such purposes is at the customer’s own risk. Wolfson does not grant any licence (express or implied) under any patent right, copyright, mask work right or other intellectual property right of Wolfson covering or relating to any combination, machine, or process in which its products or services might be or are used. Any provision or publication of any third party’s products or services does not constitute Wolfson’s approval, licence, warranty or endorsement thereof. Any third party trade marks contained in this document belong to the respective third party owner. Reproduction of information from Wolfson datasheets is permissible only if reproduction is without alteration and is accompanied by all associated copyright, proprietary and other notices (including this notice) and conditions. Wolfson is not liable for any unauthorised alteration of such information or for any reliance placed thereon. Any representations made, warranties given, and/or liabilities accepted by any person which differ from those contained in this datasheet or in Wolfson’s standard terms and conditions of sale, delivery and payment are made, given and/or accepted at that person’s own risk. Wolfson is not liable for any such representations, warranties or liabilities or for any reliance placed thereon by any person. ADDRESS: Wolfson Microelectronics plc Westfield House 26 Westfield Road Edinburgh EH11 2QB United Kingdom Tel :: +44 (0)131 272 7000 Fax :: +44 (0)131 272 7001 E-mail :: [email protected] w Customer Information July 2014, Rev 1.1 7