WM7216E Low Power Top Port Digital Silicon Microphone DESCRIPTION FEATURES The WM7216 is a low-profile digital silicon microphone, optimised for use with low-power ‘Always-on’ voice control applications, such as Cirrus Logic® SoundClear™ software. High SNR (63dB) Low variation in sensitivity (±1dB tolerance) Low current consumption The WM7216 supports two operational modes, selected according to the applied clock frequency. ‘Voice’ mode provides low current consumption, and sufficient SNR performance for speech recognition algorithms. ‘Hi-Fi Record’ mode offers wide dynamic range, and classleading THD performance. Operation in the ultrasonic band is also supported at high clock frequencies. The WM7216 incorporates Cirrus Logic proprietary CMOS/MEMS membrane technology, offering high reliability and high performance in a miniature, low-profile package. The WM7216 is designed to withstand the high temperatures associated with automated flow solder assembly processes. (Note that conventional microphones can be damaged by this process.) The WM7216 incorporates a high-performance ADC, which outputs a single-bit data stream using Pulse Density Modulation (PDM) encoding. The WM7216 supports selectable left/right channel assignment for a two-channel digital microphone interface, enabling efficient connection of multiple microphones in stereo/array configurations. The WM7216 offers tight tolerance on the microphone sensitivity, giving reduced variation between parts. This removes the need for in-line production calibration of partto-part microphone variations. BLOCK DIAGRAM - 10μA (Sleep) - 290μA (Voice mode) - 980μA (Hi-Fi Record mode) PDM digital audio output Stereo/array operation Proprietary ADC technology - Reduced clock-jitter sensitivity - Low noise floor - Stable in overload condition Top Port LGA Package 1.62V to 2.0V supply APPLICATIONS Mobile telephone handsets Wearable devices Portable media players Digital cameras Tablets and laptop computers 3D VIEW VDD WM7216 CLK CONTROL CHARGE PUMP AMP DAT LRSEL ADC CMOS MEMS Transducer GND http://www.cirrus.com 4.00mm x 3.00mm x 1.00mm LGA package Copyright Cirrus Logic, Inc., 2014–2016 (All Rights Reserved) Rev 4.0 MAY ‘16 WM7216E TABLE OF CONTENTS DESCRIPTION ................................................................................................................ 1 FEATURES ..................................................................................................................... 1 APPLICATIONS ............................................................................................................. 1 BLOCK DIAGRAM ......................................................................................................... 1 3D VIEW ......................................................................................................................... 1 TABLE OF CONTENTS.................................................................................................. 2 PIN CONFIGURATION ................................................................................................... 3 PIN DESCRIPTION ......................................................................................................... 3 ORDERING INFORMATION ........................................................................................... 3 ABSOLUTE MAXIMUM RATINGS ................................................................................. 4 IMPORTANT ASSEMBLY GUIDELINES ....................................................................... 4 RECOMMENDED OPERATING CONDITIONS .............................................................. 4 ACOUSTIC AND ELECTRICAL CHARACTERISTICS .................................................. 5 TERMINOLOGY ......................................................................................................................... 7 AUDIO INTERFACE TIMING ..................................................................................................... 8 TYPICAL PERFORMANCE ............................................................................................ 9 APPLICATIONS INFORMATION ................................................................................. 10 RECOMMENDED EXTERNAL COMPONENTS ...................................................................... 10 OPTIMISED SYSTEM RF DESIGN ......................................................................................... 10 CONNECTION TO A CIRRUS LOGIC AUDIO CODEC........................................................... 10 PCB LAND PATTERN AND PASTE STENCIL ........................................................................ 11 PACKAGE DIMENSIONS ............................................................................................. 12 IMPORTANT NOTICE .................................................................................................. 13 REVISION HISTORY .................................................................................................... 14 2 Rev 4.0 WM7216E PIN CONFIGURATION 3 2 4 1 5 Top View PIN DESCRIPTION PIN NAME TYPE 1 VDD Supply DESCRIPTION 2 LRSEL Digital Input Channel select 0 = Data output following falling CLK edge 1 = Data output following rising CLK edge Internal pull-down holds this pin at logic 0 when not connected 3 CLK Digital Input Clock input 4 DAT Digital Output 5 GND Supply Power supply PDM data output Ground ORDERING INFORMATION ORDER CODE TEMPERATURE RANGE PACKAGE MOISTURE SENSITIVITY LEVEL PEAK SOLDERING TEMPERATURE WM7216IMSE/RV -40 to +100°C LGA (tape and reel) MSL2A +260°C Note: Reel quantity = 4800 All devices are Pb-free and Halogen free. Rev 4.0 3 WM7216E ABSOLUTE MAXIMUM RATINGS Absolute Maximum Ratings are stress ratings only. Permanent damage to the device may be caused by continuously operating at or beyond these limits. Device functional operating limits and guaranteed performance specifications are given under Electrical Characteristics at the test conditions specified. ESD Sensitive Device. This device is manufactured on a CMOS process. It is therefore generically susceptible to damage from excessive static voltages. Proper ESD precautions must be taken during handling and storage of this device. Cirrus Logic tests its package types according to IPC/JEDEC J-STD-020 for Moisture Sensitivity to determine acceptable storage conditions prior to surface mount assembly. These levels are: MSL1 = unlimited floor life at <30°C / 85% Relative Humidity. Not normally stored in moisture barrier bag. MSL2 = out of bag storage for 1 year at <30°C / 60% Relative Humidity. Supplied in moisture barrier bag. MSL2A = out of bag storage for 4 weeks at <30°C / 60% Relative Humidity. Supplied in moisture barrier bag. MSL3 = out of bag storage for 168 hours at <30°C / 60% Relative Humidity. Supplied in moisture barrier bag. The Moisture Sensitivity Level for each package type is specified in Ordering Information. CONDITION MIN MAX Supply Voltage (VDD) -0.3V +4.2V Voltage range digital inputs (LRSEL, CLK) -0.3V 2.3V (see note) Operating temperature range, TA -40°C +100°C Storage temperature prior to soldering 30°C max / 60% RH max Storage temperature after soldering -40°C +100°C Note: If VDD is above the minimum recommended operating level, the maximum input voltage is VDD + 0.3V. IMPORTANT ASSEMBLY GUIDELINES Do not put a vacuum over the port hole of the microphone. Placing a vacuum over the port hole can damage the device. Do not board wash the microphone after a re-flow process. Board washing and the associated cleaning agents can damage the device. Do not expose to ultrasonic cleaning methods. Do not use vapour phase re-flow process. The vapour can damage the device. Please refer to application note WAN0273 (MEMS MIC Assembly and Handling Guidelines) for further assembly and handling guidelines. RECOMMENDED OPERATING CONDITIONS PARAMETER 4 SYMBOL MIN TYP MAX UNIT VDD Supply Range VDD 1.62 1.8 2.0 V Ground GND Clock Frequency FCLK 4.9 MHz 0 0.3 V Rev 4.0 WM7216E ACOUSTIC AND ELECTRICAL CHARACTERISTICS Test Conditions: VDD=1.8V, 1kHz test signal, CLK=3.072MHz, CLOAD = 100pF, TA = 25°C, unless otherwise stated. PARAMETER SYMBOL TEST CONDITIONS MIN Directivity TYP MAX UNIT Omni-directional Polarity Positive sound pressure Sensitivity S 94dB SPL Increasing density of 1s -27 -26 -25 dBFS Voice Mode: CLK=768kHz Acoustic Overload THD < 10% 120 dB SPL 94dB SPL, 200Hz to 8kHz 0.05 % 118dB SPL, 200Hz to 8kHz 1 SNR A-weighted, 200Hz to 8kHz 60 dB DR A-weighted, 200Hz to 8kHz 84 dB Acoustic Noise Floor A-weighted, 200Hz to 8kHz 34 dB SPL Electrical Noise Floor A-weighted, 200Hz to 8kHz -86 dBFS 217Hz square wave, 100mV (peak-peak) -70 dBFS THD < 10% 120 dB SPL 94dB SPL 0.05 % 118dB SPL 1 SNR A-weighted 63 DR A-weighted 87 dB Acoustic Noise Floor A-weighted 31 dB SPL Electrical Noise Floor A-weighted -89 dBFS 217Hz square wave, 100mV (peak-peak) -65 dBFS THD < 10% 120 dB SPL % Total Harmonic Distortion Signal to Noise Ratio THD Dynamic Range Power Supply Rejection PSR Hi-Fi Record Mode: CLK=3.072MHz Acoustic Overload Total Harmonic Distortion Signal to Noise Ratio Dynamic Range Power Supply Rejection THD PSR dB Hi-Fi Record Mode (Ultrasonic operation): CLK=3.84MHz Acoustic Overload Total Harmonic Distortion Signal to Noise Ratio Dynamic Range THD 94dB SPL 0.05 118dB SPL 1 SNR A-weighted 63 DR A-weighted 87 dB A-weighted 31 dB SPL A-weighted -89 dBFS 217Hz square wave, 100mV (peak-peak) -65 dBFS -3dB low frequency 62 Hz +3dB high frequency 12000 Acoustic Noise Floor Electrical Noise Floor Power Supply Rejection PSR dB Frequency Response Frequency Response Frequency Response Flatness Rev 4.0 200Hz to 8kHz -1 +1 dB 5 WM7216E Test Conditions: VDD=1.8V, 1kHz test signal, CLK=3.072MHz, CLOAD = 100pF, TA = 25°C, unless otherwise stated. PARAMETER SYMBOL TEST CONDITIONS MIN Input HIGH Level VIH VDD = 1.8V ±10% 0.65 VDD Input LOW Level VIL VDD = 1.8V ±10% Output HIGH Level VOH IOH = 1mA Output LOW Level VOL IOL = -1mA TYP MAX UNIT Digital Input / Output 0.35 VDD 0.9 VDD Input capacitance (CLK) -1 Pull-down resistance (LRSEL) 0.1 VDD V 1 µA pF 2.5 CLOAD Short Circuit Output Current V V 3.5 Input leakage Maximum load capacitance (DAT) V MΩ 150 pF DAT connected to GND 10 mA Sleep Mode, CLK = 0Hz 10 µA Miscellaneous Current Consumption (no load connected) Start-up time Impulse recovery time CLK frequency Mode selection time 6 IVDD Voice Mode, CLK = 768kHz 290 400 Hi-Fi Record Mode, CLK = 3.072MHz 980 1250 Hi-Fi Record Mode, CLK = 3.84MHz 1010 1300 from VDD applied to output within specification 10 50 from CLK applied to output within specification 10 50 from input sound pressure below overload level to output within specification 50 Sleep Mode ms ms 0 Hz Voice Mode 300 800 kHz Hi-Fi Record Mode 2.2 4.9 MHz 4 CLK cycles Rev 4.0 WM7216E TERMINOLOGY 1. 2. 3. 4. 5. 6. 7. 8. Sensitivity (dBFS) – Sensitivity is a measure of the microphone output response to the acoustic pressure of a 1kHz 94dB SPL (1Pa RMS) sine wave. This is referenced to the output Full Scale Range (FSR) of the microphone. Full Scale Range (FSR) – Sensitivity, Electrical Noise Floor and Power Supply Rejection are measured with reference to the output Full Scale Range (FSR) of the microphone. FSR is defined as the amplitude of a 1kHz sine wave output whose positive peak value reaches 100% density of logic 1s and whose negative peak value reaches 0% density of logic 1s. This is the largest 1kHz sine wave that will fit in the digital output range without clipping. Note that, because the definition of FSR is based on a sine wave, it is possible to support a square wave test signal output whose level is +3dBFS. Total Harmonic Distortion (%) – THD is the ratio of the RMS sum of the harmonic distortion products in the specified bandwidth (see note below) relative to the RMS amplitude of the fundamental (ie. test frequency) output. Signal-to-Noise Ratio (dB) – SNR is a measure of the difference in level between the output response of a 1kHz 94dB SPL sine wave and the idle noise output. Dynamic Range (dB) – DR is the ratio of the 1% THD microphone output level (in response to a sine wave input) and the idle noise output level. All performance measurements are carried out within a 20Hz to 20kHz bandwidth and, where noted, an A-weighted filter. Failure to use these filters will result in higher THD and lower SNR values than are found in the Acoustic and Electrical Characteristics. The brick wall filter removes out of band noise. Hi-Fi Record mode and Voice mode are selected according to CLK frequency, as described above. Sleep Mode is enabled when the CLK input is stopped; this is a power-saving mode. Normal operation resumes automatically when the CLK input frequency is within the specified operational limits. Note that the VDD supply is still required in Sleep mode. Rev 4.0 7 WM7216E AUDIO INTERFACE TIMING tCY CLK (input) tL_DV DAT (LRSEL = 1) tL_DIS tL_EN tR_DV DAT (LRSEL = 0) tR_DIS tR_EN DAT is high-impedance (hi-z) when not outputting data Figure 1 Digital Microphone Interface Timing Test Conditions The following timing information is valid across the full range of recommended operating conditions. PARAMETER SYMBOL MIN TYP MAX UNIT ns Digital Microphone Interface Timing CLK cycle time CLK duty cycle 204 3333 fCLK <= 3.072MHz tCY 60:40 40:60 fCLK > 3.072MHz 52:48 48:52 CLK rise/fall time 6 DAT enable from rising CLK edge (LRSEL = 1) tL_EN 24 DAT valid from rising CLK edge (LRSEL = 1) tL_DV 30 DAT disable from falling CLK edge (LRSEL = 1) tL_DIS DAT enable from falling CLK edge (LRSEL = 0) tR_EN 24 DAT valid from falling CLK edge (LRSEL = 0) tR_DV 30 DAT disable from rising CLK edge (LRSEL = 0) tR_DIS ns ns 80 ns 20 ns ns 80 ns 20 ns Notes: 1. The DAT output is high-impedance when not outputting data; this enables the outputs of two microphones to be connected together with the data from one microphone interleaved with the data from the other. (The microphones must be configured to transmit on opposite channels in this case.) 2. In a typical configuration, the Left channel is transmitted following the rising CLK edge (LRSEL = 1). In this case, the Left channel should be sampled by the receiving device on the falling CLK edge. 3. Similarly, the Right channel is typically transmitted following the falling CLK edge (LRSEL = 0). In this case, the Right channel should be sampled by the receiving device on the rising CLK edge. 4. The WM7216 operating mode is selected according to the CLK frequency; see “Acoustic and Electrical Characteristics” for further details. 8 Rev 4.0 WM7216E TYPICAL PERFORMANCE Sensitivity vs. Frequency (CLK = 3.072MHz) Rev 4.0 THD vs. Sound Pressure Level 9 WM7216E APPLICATIONS INFORMATION RECOMMENDED EXTERNAL COMPONENTS It is recommended to connect a 0.1µF decoupling capacitor between the VDD and GND pins of the WM7216. A ceramic 0.1µF capacitor with X7R dielectric or better is suitable. The capacitor should be placed as close to the WM7216 as possible. OPTIMISED SYSTEM RF DESIGN For optimised RF design please refer to document WAN0278 (Recommended PCB Layout for Microphone RF Immunity in Mobile Cell Phone Applications) for further information. CONNECTION TO A CIRRUS LOGIC AUDIO CODEC Cirrus Logic provides a range of audio CODECs incorporating a digital microphone input interface; these support direct connection to digital microphones such as the WM7216. Stereo connection of two WM7216 digital microphones is illustrated in Figure 2. Further information on Cirrus Logic audio CODECs is provided in the respective product datasheet, which is available from the Cirrus Logic website. VDD WM7216 VDD Audio CODEC CLK 0.1F DAT DMICCLK DMICDAT LRSEL GND VDD WM7216 VDD CLK 0.1F DAT LRSEL GND Figure 2 Stereo WM7216 Digital Microphone Connection 10 Rev 4.0 WM7216E PCB LAND PATTERN AND PASTE STENCIL The recommended PCB Land Pattern and Paste Stencil Pattern for the WM7216 microphone are shown in Figure 3 and Figure 4. See also Application Note WAN0284 (General Design Considerations for MEMS Microphones) for further details of PCB footprint design. Full definition of the package dimensions is provided in the “Package Dimensions” section. Figure 3 DM096 - PCB Land Pattern, Top View Figure 4 DM096 - Paste Stencil Pattern, Top View Rev 4.0 11 WM7216E PACKAGE DIMENSIONS 12 Rev 4.0 WM7216E IMPORTANT NOTICE Contacting Cirrus Logic Support For all product questions and inquiries, contact a Cirrus Logic Sales Representative. To find one nearest you, go to www.cirrus.com. The products and services of Cirrus Logic International (UK) Limited; Cirrus Logic, Inc.; and other companies in the Cirrus Logic group (collectively either “Cirrus Logic” or “Cirrus”) are sold subject to Cirrus Logic’s terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, indemnification, and limitation of liability. Software is provided pursuant to applicable license terms. Cirrus Logic reserves the right to make changes to its products and specifications or to discontinue any product or service without notice. Customers should therefore obtain the latest version of relevant information from Cirrus Logic to verify that the information is current and complete. Testing and other quality control techniques are utilized to the extent Cirrus Logic deems necessary. Specific testing of all parameters of each device is not necessarily performed. In order to minimize risks associated with customer applications, the customer must use adequate design and operating safeguards to minimize inherent or procedural hazards. Cirrus Logic is not liable for applications assistance or customer product design. The customer is solely responsible for its selection and use of Cirrus Logic products. Use of Cirrus Logic products may entail a choice between many different modes of operation, some or all of which may require action by the user, and some or all of which may be optional. Nothing in these materials should be interpreted as instructions or suggestions to choose one mode over another. Likewise, description of a single mode should not be interpreted as a suggestion that other modes should not be used or that they would not be suitable for operation. Features and operations described herein are for illustrative purposes only. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). CIRRUS LOGIC PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE IN PRODUCTS SURGICALLY IMPLANTED INTO THE BODY, AUTOMOTIVE SAFETY OR SECURITY DEVICES, NUCLEAR SYSTEMS, LIFE SUPPORT PRODUCTS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF CIRRUS LOGIC PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK AND CIRRUS LOGIC DISCLAIMS AND MAKES NO WARRANTY, EXPRESS, STATUTORY OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, WITH REGARD TO ANY CIRRUS LOGIC PRODUCT THAT IS USED IN SUCH A MANNER. IF THE CUSTOMER OR CUSTOMER’S CUSTOMER USES OR PERMITS THE USE OF CIRRUS LOGIC PRODUCTS IN CRITICAL APPLICATIONS, CUSTOMER AGREES, BY SUCH USE, TO FULLY INDEMNIFY CIRRUS LOGIC, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AND OTHER AGENTS FROM ANY AND ALL LIABILITY, INCLUDING ATTORNEYS’ FEES AND COSTS, THAT MAY RESULT FROM OR ARISE IN CONNECTION WITH THESE USES. This document is the property of Cirrus Logic and by furnishing this information, Cirrus Logic grants no license, express or implied, under any patents, mask work rights, copyrights, trademarks, trade secrets or other intellectual property rights. Any provision or publication of any third party’s products or services does not constitute Cirrus Logic’s approval, license, warranty or endorsement thereof. Cirrus Logic gives consent for copies to be made of the information contained herein only for use within your organization with respect to Cirrus Logic integrated circuits or other products of Cirrus Logic, and only if the reproduction is without alteration and is accompanied by all associated copyright, proprietary and other notices and conditions (including this notice). This consent does not extend to other copying such as copying for general distribution, advertising or promotional purposes, or for creating any work for resale. This document and its information is provided “AS IS” without warranty of any kind (express or implied). All statutory warranties and conditions are excluded to the fullest extent possible. No responsibility is assumed by Cirrus Logic for the use of information herein, including use of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third parties. Cirrus Logic, Cirrus, the Cirrus Logic logo design, and SoundClear are among the trademarks of Cirrus Logic. Other brand and product names may be trademarks or service marks of their respective owners. Copyright © 2014–2016 Cirrus Logic, Inc. All rights reserved. Rev 4.0 13 WM7216E REVISION HISTORY DATE REV 13/06/14 1.0 Initial version 28/10/14 2.0 Operating voltage and frequency range extended Electrical Characteristics updated Performance graphs added Package Outline Drawing updated 10/08/15 2.1 Operating voltage and frequency amended Electrical Characteristics updated Timing specifications updated PCB Land Pattern and Paste Stencil Pattern updated Package Outline Drawing updated 17/11/15 2.2 Frequency response specification updated Input capacitance specification updated Frequency response performance graph added 09/12/15 3.0 Raised to Pre-Production status PH 01/03/16 4.0 Raised to Production status PH 14 DESCRIPTION OF CHANGES PAGE CHANGED BY PH 1, 4, 7 1, 5, 6 8 11 PH 1, 4 5, 6 8 11 12 PH 5 6 9 PH Rev 4.0