Spec

JEWEL HILL ELECTRONIC CO.,LTD.
JEWEL HILL ELECTRONIC CO.,LTD.
SPECIFICATIONS FOR
LCD MODULE
JHB0802A
Module No.
E-mail: [email protected]
JHB0802A
VER: 2.01
Website: www.jhlcd.com
-0-
Issue date: 2013/08/01
JEWEL HILL ELECTRONIC CO.,LTD.
TABLE OF CONTENTS
LCM NUMBER SYSTEM ..................................................................... 2
1.
GENERAL DESCRIPTION ........................................................... 3
2.
FEATURES...................................................................................... 3
3.
MECHANICAL SPECIFICATION .............................................. 3
4.
MECHANICAL DIMENSION ....................................................... 4
5.
MAXIMUM RATINGS .................................................................. 5
6.
ELECTRICAL CHARACTERISTICS ......................................... 5
7.
MODULE FUNCTION DESCRIPTION ...................................... 6
8.
ELECTRO-OPTICAL CHARACTERISTICS .......................... 12
9.
RELIABILITY............................................................................... 16
10. PRECAUTIONS FOR USING LCD MODULES ...................... 17
11. USING LCD MODULES .............................................................. 19
12. REVISION HISTORY .................................................................. 21
SAMPLE APPROVED REPORT ....................................................... 22
JHB0802A
VER: 2.01
-1-
Issue date: 2013/08/01
JEWEL HILL ELECTRONIC CO.,LTD.
LCM Number System
JH B 08
02 A S Y E E G W U A -V00 -SC
SPECIAL CODE: P: PIN;C:CONNECT; F:CABLE; H: HEAT SEAL; O: OTHER;TP:WITH TP........
VERSION NUMBER: V00～V99
IC TYPE:
A:IC WITH CONTROLLER
B:IC WITHOUT CONTROLLER
O: OTHER TYPE
VIEWING DIRECTION:
U: UPPER(12:00); D: DOWN(6:00)
L: LEFT(9:00);
R: RIGHT(3:00); O: OTHER
TEMPERATURE RANGE:
N: NORMAL TEMPERATURE RANGE
M: MIDDLE TEMPERATURE RANGE
W: WIDE TEMPERATURE RANGE
S: SUPER WIDE TEMPERATURE RANGE
BACKLIGHT COLOR:
A: AMBER; B: BLUE; Y: YELLOW-GREEN;
G: GREEN;
R: RED;
W: WHITE; T: DOUBLE LED BACKLIGHT;
E: TWO COLOUR LED BACKLIGHT; N: THREE COLOUR LED BACKLIGHT; O: OTHER COLOR;
BACKLIGHT TYPE:
E: EL; L: LED; C: CCFL; N: NONE; O: OTHER
LCD POLARIZER TYPE:
R: POSITIVE REFLECTIVE;
P: POSITIVE TRANSMISSIVE;
E: POSITIVE TRANSFLECTIVE;
M: NEGATIVE TRANSFLECTIVE
T: NEGATIVE TRANSMISSIVE;
LCD COLOR MODE:
G: GRAY;
Y:YELLOW-GREEN; B: BLUE;
W: BLACK-WHITE; O: OTHER;
LCD TYPE:
F: FSTN; D: DSTN; P: DFSTN; N: TN; H: HTN; S: STN;
T: FSC(TN COLOUR); B: BLACK-MARSK. V: VA-BLACK(EBT);O: OTHER;
SERIAL NUMBER: A～Z
GRAPHIC MODULEs: NUMBER OF COMMONs
CHARACTER MODULEs: NUMBER OF LINE
GRAPHIC MODULEs:NUMBER OF SEGMENTs
CHARACTER MODULEs:
LCM TYPE:
B: COB & SMT LCM; T: TAB LCM; G: COG LCM;
H: HEAT SEAL+LCD(NO IC) LCM; P: FPC+LCD(NO IC) LCM;
L: BACKLIGHT+LCD(NO IC) LCM; C: COF LCM; O: OTHER;
JEWEL HILL ELECTRONIC CO.,LTD.
JHB0802A
VER: 2.01
-2-
Issue date: 2013/08/01
JEWEL HILL ELECTRONIC CO.,LTD.
1. GENERAL DESCRIPTION
The JHB0802A is a 8C x 2L Character LCD module. It has a STN panel composed of 40 segments
and 16 commons. The LCM can be easily accessed by micro-controller via parallel interface.
2. FEATURES
Display Mode
Display Format
Input Data
Transflective and positive
STN(Yellow - Green) module
Character 8C x 2L
8/4-bit parallel data input from MPU
Multiplexing Ratio 1/16 Duty
Bias
1/5 Bias
Viewing Direction 12 O’clock
Backlight
EL
3. MECHANICAL SPECIFICATION
Item
Specifications
Unit
Dimensional outline
40.0 x 35.4 x 7.5(max)
mm
Resolution
40segs x 16coms
dots
View area
30.4(W) x 13.9(H)
mm
Active area
26.4(W) x 9.9(H)
mm
Char. pitch
3.35(W) x 5.15(H)
mm
Char. size
2.95(W) x 4.75(H)
mm
Dots pitch
0.6 (W)×0.6(H)
mm
Dots size
0. 55(W)×0.55(H)
mm
JHB0802A
VER: 2.01
-3-
Issue date: 2013/08/01
JEWEL HILL ELECTRONIC CO.,LTD.
4. MECHANICAL DIMENSION
1
VSS
2
VDD
3
VO
4
RS
5
R/W
6
E
7
DB0
8
DB1
9
DB2
10
DB3
11
*2
*1
TYPE
--
14
DB7
7.5
-
13
DB6
VER: 2.01
R&EL 4.0
12
DB5
LED
DB4
JHB0802A
-4-
Issue date: 2013/08/01
JEWEL HILL ELECTRONIC CO.,LTD.
5. MAXIMUM RATINGS
Item
Symbol
Min
Max
Unit
VDD - Vss
-0.3
7.0
V
VLCD
VDD-12
VDD+0.3
V
Input Voltage
VIN
-0.3
VDD+0.3
Operating temperature
TOPR
-20
+70
V
℃
Storage temperature
TSTR
-30
+80
℃
---
---
90
%RH
Supply voltage
Humidity
Note
6. ELECTRICAL CHARACTERISTICS
Item
Supply Voltage
Input Voltage
Symbol
Condition
Min.
Typ.
Logic
VDD
---
-
5.0
H level
VIH
0.7VDD
---
L level
VIL
Current Consumption
(LCD DRIVER)
LCD Driving Voltage
---
-0.2
---
Max.
5.5
VDD
0.2 VDD
Uni
t
V
V
VDD=5.0V;
IDD
VLCD=4.7V,Tamb=25℃;
---
---
1.2
mA
VLCD
Bias=1/5
VLCD=VDD-VO
4.4
4.7
4.9
V
-
AC～110
-
V
VDD=5.0V;
With Backlight(E/L)
JHB0802A
VER: 2.01
VEL
VLCD=4.7V,Tamb=25℃;
-5-
Issue date: 2013/08/01
JEWEL HILL ELECTRONIC CO.,LTD.
7. MODULE FUNCTION DESCRIPTION
7.1. PIN DESCRIPTION
Pin No.
Symbol
Description
1
VSS
Power supply for Ground (0V)
2
VDD
Power supply for positive (+5V)
3
VO
LCD driving voltage regulation terminal
4
RS
Data/Command register selection;
5
R/W
6
E
7
DB0
8
DB1
9
DB2
10
DB3
Read/write selection signal,
“H”: Data;
“L”: Command
”H”: Read; ”L”: Write
Read/write Enable signal input pin
8-bit bi-directional data bus
11
DB4
12
DB5
13
DB6
14
DB7
JHB0802A
VER: 2.01
-6-
Issue date: 2013/08/01
JEWEL HILL ELECTRONIC CO.,LTD.
7.2 TIMING CHARACTERISTICS
1. SYSTEM BUS READ/WRITE CHARACTERISTIC
JHB0802A
VER: 2.01
-7-
Issue date: 2013/08/01
JEWEL HILL ELECTRONIC CO.,LTD.
JHB0802A
VER: 2.01
-8-
Issue date: 2013/08/01
JEWEL HILL ELECTRONIC CO.,LTD.
7.3 APPLICATION OF LCM
„Reference circuit
„Circuit Block Diagram
JHB0802A
VER: 2.01
-9-
Issue date: 2013/08/01
JEWEL HILL ELECTRONIC CO.,LTD.
7.4 TABLE OF COMMAND
JHB0802A
VER: 2.01
- 10 -
Issue date: 2013/08/01
JEWEL HILL ELECTRONIC CO.,LTD.
7.5 CHARACTER GENERATOR ROM
JHB0802A
VER: 2.01
- 11 -
Issue date: 2013/08/01
JEWEL HILL ELECTRONIC CO.,LTD.
8. ELECTRO-OPTICAL CHARACTERISTICS
Item
Symbol
LCD driving
Condition
θ=ψ= 0
VLCD
voltage
Rise Time (Tr)
Temp
Min
Typ.
Max
0℃
-
4.9
-
25℃
4.4
4.7
4.9
50℃
-
4.5
-
---
---
--
---
----
---
---
225
340
---
240
360
---
---
--
---
---
--
5
10
---
0℃
Decay Time (Tf)
Response Time
Rise Time (Tr)
Decay Time (Tf)
θ=ψ= 0
Rise Time (Tr)
25℃
50℃
Decay Time (Tf)
Contrast Ratio
Viewing Angle
Range
θ(25℃)
Cr
θ=ψ= 0
25℃
θ(ψ= 0°)
ψ= 90°
ψ=180°
ψ=270°
(6”)
(3”)
(12”)
(9”)
35
30
25
25
CR≥2
Units
Note
V
NOTE1
msec
---
NOTE2
NOTE4
備註
Deg
NOTE3
z For panel only
JHB0802A
VER: 2.01
- 12 -
Issue date: 2013/08/01
JEWEL HILL ELECTRONIC CO.,LTD.
․Electro-Optical Characteristics Measuring Equipment(DMS501)
Printer
Detector
Positioning
(θ,φ)
Display
Driver
LCD
Temperature
Control
System
JHB0802A
VER: 2.01
Illumination (D65)
- 13 -
Issue date: 2013/08/01
JEWEL HILL ELECTRONIC CO.,LTD.
․Note 1.
Definition of Driving Voltage( Vlcd) :
Selected Waveform
100 %
30 %
50 %
Non-Selected Waveform
50 %
Vth2
Vth1
Operation Voltage
Vlcd
․Note 2.
Definition of Optical Response Time :
NO SELECTED
WAVEFORM
(10SEC)
SELECTED WAVEFORM
(10SEC)
NO SELECTED
WAVEFORM
(10SEC)
10%
Brightness
100%
90%
100%
Tr
Tf
Rise Time
Fall Time
t
JHB0802A
VER: 2.01
- 14 -
Issue date: 2013/08/01
JEWEL HILL ELECTRONIC CO.,LTD.
․Note 3.
Definition of Viewing Angle θ and ψ :
Normal :
θ=0° 12 O’clock Direction
φ=180°
θ
φ=90°
φ=270°
9 O’clock Direction
3 O’clock Direction
φ
φ=0°
Viewing Direction
6 O’clock Direction
․Note 4.
Definition of Contrast ratio( CR) :
Brightness (%)
CR =
Brightness of Non-selected Segment (B2)
Brightness of Selected Segment (B1)
Brightness Curve for
Selected Segment
100%
B2
Brightness Curve for
Non-selected Segment
CR,max
B1
0%
Driving Voltage
V,max
JHB0802A
Contrast
VER: 2.01
- 15 -
Issue date: 2013/08/01
JEWEL HILL ELECTRONIC CO.,LTD.
9. RELIABILITY
9.1. MTBF
The LCD module shall be designed to meet a minimum MTBF value of 30000 hours with normal.
(25°C in the room without sunlight)
9.2. TESTS
NO.
ITEM
CONDITION
CRITERION
。No Defect Of
1
High Temperature Operating
70℃
120Hrs
Operational Function In
Room Temperature Are
Allowable.
2
Low Temperature Operating
-20℃
120Hrs
。IDD of LCM in
3
High Temperature/
Humidity Non-Operating
60℃ ,90%RH ,120 Hrs
4
High Temperature
Non-Operating
80℃ 120Hrs
5
Low Temperature
Non-Operating
-30℃ 120Hrs
6
Temperature Cycling
Non-Operating
Pre-and post-test should
follow specification
-20℃(30Min )↔ 60℃(30Min)
10 CYCLES
Notes: Judgments should be mode after exposure in room temperature for two hours.
JHB0802A
VER: 2.01
- 16 -
Issue date: 2013/08/01
JEWEL HILL ELECTRONIC CO.,LTD.
10. PRECAUTIONS FOR USING LCD MODULES
10.1. HANDLING PRECAUTIONS
(1) The display panel is made of glass. Do not subject it to a mechanical shock or impact by dropping
it.
(2) If the display panel is damaged and the liquid crystal substance leaks out, be sure not to get any in
your mouth. If the substance contacts your skin or clothes, wash it off using soap and water.
(3) Do not apply excessive force to the display surface or the adjoining areas since this may cause the
color tone to vary.
(4) The polarizer covering the display surface of the LCD module is soft and easily scratched. Handle
this polarizer carefully.
(5) If the display surface becomes contaminated, breathe on the surface and gently wipe it with a soft
dry cloth. If it is heavily contaminated, moisten a cloth with one of the following solvents:
- Isopropyl alcohol
- Ethyl alcohol
(6) Solvents other than those above mentioned may damage the polarizer.
Especially, do not use the following:
- Water
- Ketone
- Aromatic solvents
(7) Extra care to minimize corrosion of the electrode. Water droplets, moisture condensation or a
current flow in a high-humidity environment accelerates corrosion of the electrode.
(8) Install the LCD Module by using the mounting holes. When mounting the LCD Module, make
sure it is free of twisting, warping and distortion. In particular, do not forcibly pull or bend the I/O
cable or the backlight cable.
(9) Do not attempt to disassemble or process the LCD Module.
(10) NC terminal should be open. Do not connect anything.
(11) If the logic circuit power is off, do not apply the input signals.
(12) To prevent destruction of the elements by static electricity, be careful to maintain an optimum
work environment.
- Be sure to ground the body when handling he LCD Module.
- Tools required for assembling, such as soldering irons, must be properly grounded.
-To reduce the amount of static electricity generated, do not conduct assembling and other work
under dry conditions.
JHB0802A
VER: 2.01
- 17 -
Issue date: 2013/08/01
JEWEL HILL ELECTRONIC CO.,LTD.
-The LCD Module is coated with a film to protect the display surface. Exercise care when peeling
off this protective film since static electricity may be generated.
10.2. STORAGE CONDITIONS
When storing, avoid the LCD module to be exposed to direct sunlight of fluorescent lamps. For
stability, to keep it away form high temperature and high humidity environment (The best condition
is : 23±5°C, 45±20%RH). ESD protection is necessary for long-term storage also.
10.3. OTHERS
Liquid crystals solidify under low temperature (below the storage temperature range) leading to
defective orientation or the generation of air bubbles (black or white). Air bubbles may also be
generated if the module is subject to a low temperature.
If the LCD Module have been operating for a long time showing the same display patterns the display
patterns may remain on the screen as ghost images and a slight contrast irregularity may also appear.
A normal operating status can be recovered by suspending use for some time. It should be noted that
this phenomenon does not adversely affect performance reliability.
To minimize the performance degradation of the LCD Module resulting from destruction caused by
static electricity etc. exercise care to avoid holding the following sections when handling the modules.
- Exposed area of the printed circuit board.
- Terminal electrode sections.
JHB0802A
VER: 2.01
- 18 -
Issue date: 2013/08/01
JEWEL HILL ELECTRONIC CO.,LTD.
11. Using LCD modules
11.1 LIQUID CRYSTAL DISPLAY MODULES
LCD is composed of glass and polarizer. Pay attention to the following items when handling.
(1) Please keep the temperature within specified range for use and storage. Polarization degradation,
bubble generation or polarizer peel-off may occur with high temperature and high humidity.
(2) Do not touch, push or rub the exposed polarizers with anything harder than a HB pencil lead (glass,
tweezers, etc).
(3) N-hexane is recommended for cleaning the adhesives used to attach front/rear polarizers and
reflectors made of organic substances, which will be damaged by chemicals such as acetone,
toluene, toluene, ethanol and isopropyl alcohol.
(4) When the display surface becomes dusty, wipe gently with absorbent cotton or other soft material
like chamois soaked in petroleum ether. Do not scrub hard to avoid damaging the display surface.
(5) Wipe off saliva or water drops immediately, contact with water over a long period of time may
cause deformation or color fading.
(6) Avoid contacting oil and fats.
(7) Condensation on the surface and contact with terminals due to cold will damage, stain or
polarizers. After products are tested at low temperature they must be warmed up in a container
before coming is contacting with room temperature air.
(8) Do not put or attach anything on the display area to avoid leaving marks on.
(9) Do not touch the display with bare hands. This will stain the display area and degrade insulation
between terminals (some cosmetics are determinate to the polarizers).
(10)As glass is fragile, it tends to become or chipped during handling especially on the edges. Please
avoid dropping or jarring.
11.2 INSTALLING LCD MODULE
Attend to the following items when installing the LCM.
(1) Cover the surface with a transparent protective plate to protect the polarizer and LC cell.
(2) When assembling the LCM into other equipment, the spacer to the bit between the LCM and the
fitting plate should have enough height to avoid causing stress to the module surface, refer to the
individual specifications for measurements. The measurement tolerance should be ±0.1mm.
11.3 ELECTRO-STATIC DISCHARGE CONTROL
Since this module uses a CMOS LSI, the same careful attention should be paid for electrostatic
discharge as for an ordinary CMOS IC.
JHB0802A
VER: 2.01
- 19 -
Issue date: 2013/08/01
JEWEL HILL ELECTRONIC CO.,LTD.
(1) Make certain that you are grounded when handing LCM.
(2) Before removing LCM from its packing case or incorporating it into a set, be sure the module and
your body have the same electric potential.
(3) When soldering the terminal of LCM, make certain the AC power source for the soldering iron
does not leak.
(4) When using an electric screwdriver to attach LCM, the screwdriver should be of ground
potentiality to minimize as much as possible any transmission of electromagnetic waves produced
sparks coming from the commutator of the motor.
(5) As far as possible, make the electric potential of your work clothes and that of the workbenches to
the ground potential.
(6) To reduce the generation of electro-static discharge, be careful that the air in the work is not too
dried. A relative humidity of 50%-60% is recommended.
11.4 PRECAUTIONS FOR OPERATION
(1) Viewing angle varies with the change of liquid crystal driving voltage (Vo). Adjust Vo to show
the best contrast.
(2) Driving the LCD in the voltage above the limit will shorten its lifetime.
(3) Response time is greatly delayed at temperature below the operating temperature range. However,
this does not mean the LCD will be out of the order. It will recover when it returns to the specified
temperature range.
(4) If the display area is pushed hard during operation, the display will become abnormal. However, it
will return to normal if it is turned off and then on.
(5) Condensation on terminals can cause an electrochemical reaction disrupting the terminal circuit.
Therefore, this product must be used and stored within the specified condition of 23±5°C,
45±20%RH.
(6) When turning the power on, input each signal after the positive/negative voltage becomes stable.
11.5 SAFETY
(1) It is recommended to crush damaged or unnecessary LCDs into pieces and wash them off with
solvents such as acetone and ethanol, which should later be burned.
(2) If any liquid leaks out of a damaged glass cell and comes in contact with the hands, wash off
thoroughly with soap and water.
JHB0802A
VER: 2.01
- 20 -
Issue date: 2013/08/01
JEWEL HILL ELECTRONIC CO.,LTD.
12. REVISION HISTORY
Version
Revise record
Date
1.0
Original version
05-01-01
2.0
Change specification format
Perfect the VER2.0 spec，Commany internal modify.
05-11-19
2.01
JHB0802A
VER: 2.01
- 21 -
13-08-01
Issue date: 2013/08/01
JEWEL HILL ELECTRONIC CO.,LTD.
SAMPLE APPROVED REPORT
(样品确认单)
SAMPLE MODEL NO. (样品型号)
JHB0802A
SAMPLE SERIES NUMBER NO. (样品序号)
SAMPLE QUANTITY (样品数量)
COLOR/TYPE (底色/类型)
STN/Y-G
VIEWING DIRECTION (视角)
12:00
DRIVING METHOD (驱动参数)
1/16Duty, 1/5Bias
LOGIC VOLTAGE (IC 工作电压)
5.0V
LCD VOP (LCD 驱动电压)
4.7V
OPERATING TEMP. (操作温度) ℃
-20 ~ 70℃
STORAGE TEMP. (储存温度) ℃
-30 ~ 80℃
POLARIZER----FRONT (首偏光片)
POLARIZER----BACK (后偏光片)
TRANSFLECTIVE
CONTROLLER/DRIVER IC(控制/驱动 IC)
SPLC780D
BACKLIGHT COLOR/TYPE (背光源类型/颜色)
WITH E/L(GREEN)
DRAWING REV/NO./QUANTITY (图纸版本/数量)
SPECIFICATION (规格书
份数)
REMARKS：
(备注)
WRIT BY：_________ DATE：_________ APROV BY：_________ DATE：________
CUSTOMER’S APPROVAL (客户确认)：
1） FUNCTION （功能）：
OK
N.G.
2） DRIVER CONDITION （驱动条件）：
OK
N.G.
3） DISPLAY MODE （显示模式）：
OK
N.G.
4） VIEWING ANGLE （视角）：
OK
N.G.
5） BACKLIGHT （背光源）：
OK
N.G.
6） DISPLAYING PATTERN （显示效果）：
OK
N.G.
CUSTOMER’S CONCLUSIONS (客户意见)：______________________________________
_______________________________________________________________________________
________________________________________
CUSTOMER’S SIGNATURE（客户签名）：_____________ DATE (日期)：___________
JHB0802A
VER: 2.01
- 22 -
Issue date: 2013/08/01