PCB Mount Datasheet CN Series • 5mm Mini SIP SSR • Ratings 24VDC @ 3.5A, 48VDC @ 100mA and 240VAC @ 2A • DC Control, 5, 24 and 60V • UL & cUL recognized @ 40°C, 100K-Cycle Endurance Test • CE & RoHS Compliant PRODUCT SELECTION Control Voltage 3-12 VDC 15-30 VDC 38-72 VDC AVAILABLE OPTIONS 3.5A 100mA CN024D05 CN024D24 CN024D60 CN048D05 CN048D24 CN048D60 CN024Dxx CN048Dxx 2A CN240A05 CN240A24 CN240A60 OUTPUT SPECIFICATIONS (1) Description Operating Voltage Maximum Load Current @ 40°C (2) Minimum Load Current [mA] Maximum Blocking Voltage Maximum Surge Current [Apk] Maximum I²t for fusing 50/60Hz (1/2 cycle) [A² sec] Typical On-State Voltage Drop @ Rated Current (V) Maximum Off-State Leakage Current @ Rated Voltage [mA] Maximum PWM (Hz) (4) Minimum Off-State dv/dt @ Maximum Rated Voltage [V/µsec] (5) Switch Configuration Do not forget to visit us at: www.crydom.com Copyright © 2016 Crydom Inc. Specifications subject to change without notice. 0-24 VDC 3.5A 1 30 VDC 9 (10ms) N.A. 0.4 0.001 500 N/A N.O. 0-48 VDC 100mA (3) 1 60 VDC 0.3 mA (10ms) N.A. 1.0 0.001 500 N/A N.O. CN240Axx 24-280 VAC (47-63Hz) 2A 70 600 VAC 115/120 (50/60 Hz, 1 cycle) 66/60 1.1 (peak) 4.0 N.A. 500 N.O. PCB Mount Datasheet INPUT SPECIFICATIONS for CN024 (1) Description CN024D05 CN024D24 CN024D60 Control Voltage Range Must Turn On Voltage Must Turn Off Voltage Nominal Input Impedance Typical Input Current Typical Turn-On Time [µsec] Typical Turn-Off Time [µsec] 3.0-12 VDC 3.0 VDC 1.0 VDC 500 Ohm 10mA @ 5VDC 120 100 15-30 VDC 15 VDC 5 VDC 3.5K Ohm 7mA @ 24VDC 350 80 38-72 VDC 38 VDC 5 VDC 20K Ohm 3mA @ 60VDC 400 70 Description CN048D05 CN048D24 CN048D60 INPUT SPECIFICATIONS for CN048 (1) Control Voltage Range Must Turn On Voltage Must Turn Off Voltage Nominal Input Impedance Typical Input Current Typical Turn-On Time [µsec] Typical Turn-Off Time [µsec] INPUT SPECIFICATIONS for CN240 (1) Description Control Voltage Range Must Turn On Voltage Must Turn Off Voltage Nominal Input Impedance Typical Input Current Typical Turn-On Time [msec] (7) Typical Turn-Off Time [msec] GENERAL SPECIFICATIONS 3.0-12 VDC 3.0 VDC 1.0 VDC 1.25K Ohm 4mA @ 5VDC 20 130 16-30 VDC 16 VDC 5 VDC 3.5K Ohm 5mA @ 24VDC 20 130 38-72 VDC 38 VDC 5 VDC 20K Ohm 3mA @ 60VDC 20 130 CN240A05 CN240A24 CN240A60 3.0-12 VDC 3.0 VDC 1.0 VDC 240 Ohm 15mA @ 5VDC 1/2 Cycle 1/2 Cycle Description Dielectric Strength, Input/Output (8) Maximum Capacitance, Input/Output Ambient Operating Temperature Range Ambient Storage Temperature Range Weight (typical) Housing Material Overvoltage Category Polution Degree Degree of protection (Encapsulation) GENERAL NOTES (1) All parameters at 25°C unless otherwise specified. (2) See derate curves for more information (3) At 60°C derate by .013mA/5°C to 80°C (4) Operating frequency above 500Hz will damage the SSR (DC output only). (5) Off-state dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1 (6) Turn-on time for random turn-on version is 0.1msec. (7) 3.75KV for CN048Dxx Do not forget to visit us at: www.crydom.com Copyright © 2016 Crydom Inc. Specifications subject to change without notice. 15-30 VDC 15 VDC 5 VDC (6) 3.5K Ohm 6mA @ 24VDC 1/2 Cycle 1/2 Cycle Parameters 2.5KV 1.5 pF -20 to 80°C -20 to 100°C 0.14 oz. (4.05g) UL 94 V0 lll 2 IP67 38-72 VDC 38 VDC 5 VDC 20K Ohm 4mA @ 60VDC 1/2 Cycle 1/2 Cycle PCB Mount Datasheet MECHANICAL SPECIFICATIONS Tolerances: ±0.02 in / 0.5 mm All dimensions are in: inches [millimeters] 0.99 [25.2] 0.20 [5.0] 0.08 [1.9] 0.84 [21.4] 0.20 [5.0] 1.10 [28.0] 0.59 [15.0] 14 13(+) A1+ A2- 0.15 [3.8] 0.15 [3.8] 0.040 ±.005 [1.00 ±.13] (2PLACES) THERMAL DERATE INFORMATION Do not forget to visit us at: www.crydom.com Copyright © 2016 Crydom Inc. Specifications subject to change without notice. 0.020 ±.005 [0.50 ±.13] (2PLACES) 0.06 [1.4] 0.02 [0.4] PCB Mount Datasheet AGENCY APPROVALS Designed in accordance with the requirements of IEC 62314 ACCESSORIES Rev.060116 Do not forget to visit us at: www.crydom.com Copyright © 2016 Crydom Inc. Specifications subject to change without notice. PCB Mount Datasheet DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险 HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH. • Disconnect all power before installing or working with this equipment. • Verify all connections and replace all covers before turning on power. Failure to follow these instructions will result in death or serious injury. RIESGO DE DESCARGA ELECTRICA O EXPLOSION. • Desconectar todos los suministros de energia a este equipo antes de trabajar con este equipo. • Verificar todas las conexiones y colocar todas las tapas antes de energizer el equipo. El incumplimiento de estas instrucciones puede provocar la muerte o lesiones serias. RISQUE DE DESCHARGE ELECTRIQUE OU EXPLOSION • Eteindre toutes les sources d'énergie de cet appareil avant de travailler dessus de cet appareil • Vérifier tous connections, et remettre tous couverts en olace avant de mettre sous De non-suivi de ces instructions provoquera la mort ou des lésions sérieuses sérieuses. GEFAHR EINES ELEKTRISCHE N SCHLAGES ODER EINER EXPLOSION. • Stellen Sie jeglichen Strom ab, der dieses Gerät versorgt, bevor Sie an dem Gerät Arbeiten durchführen • Vor dem Drehen auf Energie alle Anschlüsse überprüfen und alle Abdeckungen ersetzen. Unterlassung dieser Anweisungen können zum Tode oder zu schweren Verletzungen führen. RISCHIO DI SCOSSA ELETTRICA O DELL’ESPLOSIONE. • Spenga tutta l'alimentazione che fornisce questa apparecchiatura prima di lavorare a questa apparecchiatura 存在电击、 爆炸或电弧 闪烁危险 • 在操作此设 备之前请先 关闭电源。 若不遵守这些说明， 可能会导致严重的 人身伤害甚至死亡。 • Verificare tutti i collegamenti e sostituire tutte le coperture prima dell’accensione L'omissione di queste istruzioni provocherà la morte o lesioni serie WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / 警告 RISK OF MATERIAL DAMAGE AND HOT ENCLOSURE RISQUE DE DOMMAGE MATERIEL ET DE SURCHAUFFE DU BOITIER GEFAHR VON MATERIALSCHÄDEN UND GEHÄUSEERHITZUNG • The product's side panels may be hot, allow the product to cool before touching. • Follow proper mounting instructions including torque values. • Do not allow liquids or foreign objects to enter this product. • Les panneaux latéraux du produit peuvent être chauds. Laisser le produit refroidir avant de le toucher. • Respecter les consignes de montage, et notamment les couples de serrage. • Ne pas laisser pénétrer de liquide ni de corps étrangers à l'intérieur du produit. • Die Seitenwände können heiß sein. Lassen Sie das Produkt abkühlen, bevor Sie es berühren. • Beachten Sie die Montageanweisungen, • Führen Sie keine Flüssigkeiten oder Fremdkörper in das Produkt ein. Le non-respect de cette directive peut entraîner, Failure to follow these instructions can result in des lésions corporelles graves ou des serious injury, or equipment damage. dommages matériels. Die Nichtbeachtung dieser Anweisung kann Körperverletzung oder Materialschäden zur Folge haben. RIESGO DE DAÑOS MATERIALES Y DE SOBRECALENTAMIENTO DE LA UNIDAD RISCHIO DI DANNI MATERIALI E D'INVOLUCRO CALDO 材料损坏和高温外壳的危险性 • Los paneles laterales del producto pueden estar calientes. Esperar que el producto se enfríe antes de tocarlo. • Respetar las instrucciones de montaje, y en particular los pares de apretado. • No dejar que penetren líquidos o cuerpos extraños en el producto. • I pannelli laterali dell'apparecchio possono scottare; lasciar quindi raffreddare il prodotto prima di toccarlo. • Seguire le istruzioni di montaggio corrette. • Non far entrare liquidi o oggetti estranei in questo apparecchio. Si no se respetan estas precauciones pueden producirse graves lesiones, daños materiales. La mancata osservanza di questa precauzione può causare gravi rischi per l'incolumità personale o danni alle apparecchiature. Do not forget to visit us at: www.crydom.com Copyright © 2016 Crydom Inc. Specifications subject to change without notice. • 产品的一侧面板可能很热，在其冷却前请 不要触碰。 • 遵照正确的安装说明，包括扭矩值。 • 请勿让液体及其他异物进入本产品。 如不能正确执行这些操作说明， 极有可能造成严重人体伤害或者设备的损坏。 PCB Mount Datasheet ANNEX - ENVIROMENTAL INFORMATION The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products. Part Name Toxic or hazardous Substance and Elements Lead (Pb) Mercury (Hg) Cadmium (Cd) Hexavalent Chromium (Cr (VI)) Polybrominated biphenyls (PBB) Polybrominated diphenyl ethers (PBDE) Semiconductor die Solder 附件 - 环保信息 此附件所标示的包括电子信息产品污染图标的环保信息符合中华人民共和国电子行业标准 SJ/T11364 - 2006, 电子信息产品污染控制标识要求。 部件 名称 铅 汞 镉 有毒有害物质或元素 六价铬 多溴联苯 (Pb) (Hg) (Cd) (Cr (VI)) 半导体芯片 焊接点 50 Do not forget to visit us at: www.crydom.com Copyright © 2016 Crydom Inc. Specifications subject to change without notice. (PBB) 多溴二苯醚 (PBDE)