DATA SHEET SKY13713-21: RX Diversity FEM with Gain (B29, B26, B8, B20, B12/13, B28A and B28B) Applications Antenna cable loss compensation circuit for LTE data antenna B29 3G/4G multimode cellular tablets and handsets (LTE, UMTS, CDMA2000, EDGE, and GSM) B26 B8 Embedded data cards B20 Features RF_OUT LNA RX diversity FEM with seven selectable filters and LNA paths, one Aux path and optional bypass mode RF_IN B28A VDD Integrated SAW filter and discrete LNA gain stage SDATA VIO B28B MIPI RFFE Low insertion loss thru path SAW filters: B29 (717 to 728 MHz) B26 (859 to 894 MHz) B8 (925 to 960 MHz) B20 (791 to 821 MHz) B12/13 (729 to 756 MHz) B28A (758 to 788 MHz) B28B (773 to 803 MHz) B12/13 AUX_IN AUX_OUT SCLK 203510-001 Figure 1. SKY13713-21 Block Diagram Description The SKY13713-21 is an LNA diversity module to be used in a cellular mobile device. It supports cellular diversity receiver and localization service receiver functions. Integrated MIPI interface Small (4 3 0.7 mm) 24-lead MCM package (MSL3, 260 °C per JEDEC J-STD-020) TM Skyworks Green products are compliant with all applicable legislation and are halogen-free. For additional information, refer to Skyworks Definition of GreenTM, document number SQ04–0074. It is compatible with 3GPP GSM, WCDMA, LTE and LTE standards and supports the following service bands: B29, B26, B8, B20, B12/13, B28A and B28B for the cellular part. The SKY13713-21 is packaged in a small 4 3 0.7 mm, 24lead surface mount package. No external DC blocking capacitors are required on the RF paths as long as no DC voltage is applied. The part can operate over the temperature range of –30 °C to +85 °C. A functional block diagram is shown in Figure 1. The pin configuration and package are shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203510B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 10, 2016 1 GND GND VDD VIO SDATA CLK GND GND DATA SHEET • SKY13713-21: RX DIVERSITY FEM 20 19 18 17 16 15 14 13 GND 21 ANT 22 GND GND GND 11 RX_OUT 23 10 GND 24 9 GND 7 8 GND 6 GND 5 AUX_IN 4 GND AUX_OUT 3 GND 2 GND 1 GND GND 25 203510-002 12 Figure 2. SKY13713-21 Pinout (Top View) Table 1. SKY13713-21 Signal Descriptions1 Pin Name Description Pin Name Description 1 GND RF and DC ground 13 GND RF and DC ground 2 AUX_OUT Aux output 14 GND RF and DC ground 3 GND RF and DC ground 15 CLK MIPI clock 4 GND RF and DC ground 16 SDATA MIPI data 5 GND RF and DC ground 17 VIO Voltage for the MIPI logic 6 AUX_IN Aux input 18 VDD Power supply voltage 7 GND RF and DC ground 19 GND RF and DC ground 8 GND RF and DC ground 20 GND RF and DC ground 9 GND RF and DC ground 21 GND RF and DC ground 10 GND RF and DC ground 22 ANT Antenna port 11 RX_OUT RX output port 23 GND RF and DC ground 12 GND RF and DC ground 24 GND RF and DC ground 1 Exposed pads must be connected to ground. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 2 May 10, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203510B DATA SHEET • SKY13713-21: RX DIVERSITY FEM Electrical and Mechanical Specifications The absolute maximum ratings of the SKY13713-21 are provided in Table 2. Electrical specifications are provided in Tables 3 and 4. Table 5 shows the register map information for the SKY13713-21. Table 2. SKY13713-21 Absolute Maximum Ratings1 (TOP = +25 C, Characteristic Impedance [ZO] = 50 Ω, Unless Otherwise Noted) Parameter Maximum Units VDD 3.5 V RFFE VIO VCTL 1.95 V RF input power (Peak power at ANT port) at bypass mode PIN +30 dBm Storage temperature TSTG –40 +125 C Operating temperature TOP –30 +85 C Supply voltage Symbol Minimum 1 Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. ESD HANDLING: Although this device is designed to be as robust as possible, electrostatic discharge (ESD) can damage this device. This device must be protected at all times from ESD when handling or transporting. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industrystandard ESD handling precautions should be used at all times. Table 3. SKY13713-21 General Electrical Specifications1 (VDD = 2.85 V, VIO = 1.8 V, TOP = +25 °C, Characteristic Impedance [ZO] = 50 Ω, Unless Otherwise Noted) Parameter Symbol Supply voltage VDD Digital control signal: VCTL Test Condition Min Typical Max Units 2.85 V V V VIH VIL 0.8 VIO 0 VIO 0.2 VIO RFFE VIO VCTL 1.65 1.8 1.95 V Supply current: IDD 4.5 60 6 mA A High Low High-gain mode Bypass mode 1 Performance is guaranteed only under the conditions listed in this table. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203510B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 10, 2016 3 DATA SHEET • SKY13713-21: RX DIVERSITY FEM Table 4. SKY13713-21 RF Electrical Specifications1 (1 of 2) (VDD = 2.85 V, VIO = 1.8 V, TOP = +25 °C, Characteristic Impedance [ZO] = 50 , Unless Otherwise Noted) Parameter Symbol G In-Band gain: Test Condition NF B29 @ 722.5 MHz B12/13 @ 742 MHz B28A @ 773 MHz AUX @ 860.5 MHz B28B @ 788 MHz B20 @ 806 MHz B26 @ 876.5 MHz B8 @ 942.5 MHz In-Band input return loss: B29 @ 722.5 MHz B12/13 @ 742 MHz B28A @ 773 MHz AUX @ 860.5 MHz SW @ 860.5 MHz B28B @ 788 MHz B20 @ 806 MHz B26 @ 876.5 MHz B8 @ 942.5 MHz Max Units 12 12 12 13 –1.5 12 12 12 12 13 14 14 15 –0.5 13.5 13.5 14 13.5 15 16 16 16.5 0 16 16 16.5 15.5 dB dB dB dB dB dB dB dB dB 1 1 1 0.5 1 1 1 1 2.5 2.7 2.5 1.5 2.5 3.0 2.6 2.6 4 4 4 4 4 5 4 4 dB dB dB dB dB dB dB dB –9 –10 –7.5 –8 –15 –8.5 –10 –9 –10 –6.5 –6.5 –6 –5 –10 –7 –8 –7 –7 dB dB dB dB dB dB dB dB dB –14 –15 –14 –15 –15 –13 –15 –12 –15 –8 –9 –7.5 –8.5 –10 –7.5 –9 –7 –8 dB dB dB dB dB dB dB dB dB Cascaded noise figure S11 B29 @ 722.5 MHz B12/13 @ 742 MHz B28A @ 773 MHz AUX @ 860.5 MHz SW @ 860.5 MHz B28B @ 788 MHz B20 @ 806 MHz B26 @ 876.5 MHz B8 @ 942.5 MHz In-Band output return loss: Typical Cascaded gain B29 @ 722.5 MHz B12/13 @ 742 MHz B28A @ 773 MHz AUX @ 860.5 MHz SW @ 860.5 MHz B28B @ 788 MHz B20 @ 806 MHz B26 @ 876.5 MHz B8 @ 942.5 MHz In-Band noise figure: Min S22 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 4 May 10, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203510B DATA SHEET • SKY13713-21: RX DIVERSITY FEM Table 4. SKY13713-21 RF Electrical Specifications1 (2 of 2) (VDD = 2.85 V, VIO = 1.8 V, TOP = +25 °C, Characteristic Impedance [ZO] = 50 , Unless Otherwise Noted) Parameter In-Band Bypass Mode gain: Symbol Test Condition Min Typical Max Units –6 –6 –6 –6 –6 –6 –6 –6 –4.0 –4.6 –4.3 –3.0 –4.3 –4.8 –4.3 –4.0 –3 –3 –3 –2 –3 –2 –2 –2 dB dB dB dB dB dB dB dB –30 –35 –30 –33 –30 –35 –25 –25 –25 –25 –25 –20 dB dB dB dB dB dB G B29 @ 722.5 MHz B12/13 @ 742 MHz B28A @ 773 MHz AUX @ 860.5 MHz B28B @ 788 MHz B20 @ 806 MHz B26 @ 876.5 MHz B8 @ 942.5 MHz Tx rejection: B12/13 @ 782 MHz B28A @ 718 MHz B28B @ 733 MHz B20 @ 847 MHz B26 @ 831.5 MHz B8 @ 897.5 MHz 1 Performance is guaranteed only under the conditions listed in this table. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203510B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 10, 2016 5 DATA SHEET • SKY13713-21: RX DIVERSITY FEM R No Yes OR function of Trigger0, Trigger1 and Trigger2 No Yes OR function of Trigger0, Trigger1 and Trigger2 No Yes OR function of Trigger0, Trigger1 and Trigger2 Active Trigger Description Type Default 0x0 Trigger Support RESERVED Broadcast ID Support 7:4 Function Data Bits Register Name Register Type Address Table 5. SKY13713-21 Register Map (1 of 2) Reserved for future use 0x00: Isolation 0x01: B12 0x02: B29 0x03: B13 0x00 Static ANTENNA SWITCH CONTROL 0x04: B28A 3:0 BAND_SELECT 0x0 R/W 0x05: B28B 0x06: AUX 0x07: B26 0x08: B20 0x09: B8 0x0A-0x0F: Reserved 7:4 RESERVED 0x0 R Reserved for future use 0x00: Isolation 0x01: B12 0x02: B29 0x03: B13 0x01 Static POST SWITCH & LNA CONTROL 0x04: B28A 3:0 BAND_SELECT 0x0 R/W 0x05: B28B 0x06: AUX 0x07: B26 0x08: B20 0x09: B8 0x0A-0x0F: Reserved 0x02 Dynamic 7:4 RESERVED 0x0 R 3:0 GAIN_CTRL 0x0 R/W Reserved for future use 0x0: LNA Bypass Mode LNA_GAIN_CTRL 0x9: High Gain Mode Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 6 May 10, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203510B DATA SHEET • SKY13713-21: RX DIVERSITY FEM Description Type Default Function Data Bits Register Name 0x0 R/W Reset all configurable registers to default values 6 COMMAND_FRAME_ PARITY_ERR 0x0 R/W Command Sequence received with parity error 5 COMMAND_LENGTH_ ERR 0x0 R/W Command length error 4 ADDRESS_FRAME_ PARITY_ERR 0x0 R/W Address frame with parity error 3 DATA_FRAME_ PARITY_ERR 0x0 R/W Data frame with parity error 2 READ_UNUSED _REG 0x0 R/W Read command to an invalid address 1 WRITE_UNUSED _REG 0x0 R/W Write command to an invalid address 0 BID_GID_ERR 0x0 R/W Read command with a BROADCAST_ID or GROUP_ID 7:4 RESERVED 0x0 R Reserved for future use 3:0 GROUP_SID 0x0 R/W Group slave ID RFFE_STATUS GROUP_SID Active Trigger NA SOFTWARE_RESET Trigger Support 0x1B NA 7 Broadcast ID Support 0x1A Register Type Address Table 5. SKY13713-21 Register Map (2 of 2) No No NA No No NA No NA 00: Normal operation (ACTIVE) 01: Default Settings (STARTUP) 7:6 POWER MODE 1:0 0x1 R/W Yes 10: Low power (LOW POWER) 11: Reserved 0x1C NA PM_TRIG 5 TRIGGER_MASK_2 0x0 R/W Trigger Mask 2 4 TRIGGER_MASK_1 0x0 R/W Trigger Mask 1 3 TRIGGER_MASK_0 0x0 R/W Trigger Mask 0 2 TRIGGER_2 0x0 R/W Trigger 2. This bit has no effect if TRIGGER_MASK_2 is 1. 1 TRIGGER_1 0x0 R/W Trigger 1. This bit has no effect if TRIGGER_MASK_1 is 1. 0 TRIGGER_0 0x0 R/W Trigger 0. This bit has no effect if TRIGGER_MASK_0 is 1. No Yes 0x1D NA PRODUCT_ID 7:0 PRODUCT_ID[7:0] 0xE1 R Product Identification No No NA 0x1E NA MANUFACTURER _ID 7:0 MANUFACTURER _ID[7:0] 0xA5 R LSB Manufacturing Identification No No NA 7:6 RESERVED 0x0 R Reserved for future use 5:4 MANUFACTURER _ID[9:8] 0x1 R MSB Manufacturing Identification No No NA 3:0 USID[3:0] 0x1 R/W User Identification 0x1F NA MAN_USID Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203510B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 10, 2016 7 DATA SHEET • SKY13713-21: RX DIVERSITY FEM Evaluation Board Description Package and Handling Information The SKY13713-21 Evaluation Board is used to test the performance of the SKY13713-21 RX Diversity FEM. An Evaluation Board schematic diagram is provided in Figure 3. An assembly drawing for the Evaluation Board is shown in Figure 4. Since the device package is sensitive to moisture absorption, it is baked and vacuum packed before shipping. Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. Package Dimensions The SKY13713-21 is rated to Moisture Sensitivity Level 3 (MSL3) at 260 C. It can be used for lead or lead-free soldering. For additional information, refer to the Skyworks Application Note, PCB Design & SMT Assembly/Rework Guidelines for MCM-L Packages, document number 101752. The PCB layout footprint for the SKY13713-21 is shown in Figure 5. Typical part markings are shown in Figure 6. Package dimensions are shown in Figure 7, and tape and reel dimensions are provided in Figure 8. GND 1 R4 0Ω C9 AUX OUT 30 pF J4 SMA L6 DNI 50 Ω trace GND GND SDATA SCLK SCLK VIO VIO VDD SKY13713 2 3 4 5 6 7 12 GND 10 GND 9 50 Ω trace 50 Ω trace 11 R2 L4 6.8 nH DNI C6 30 pF OUTPUT J2 SMA L5 1.5 pF GND 25 GND GND GND 13 RX_OUT GND 24 14 AUX_IN 23 15 SDATA ANT 16 GND L3 DNI 22 17 GND L2 DNI R1 0Ω GND 18 GND C4 30 pF 21 GND J1 SMA 50 Ω trace AUX_OUT INPUT 19 GND GND 20 VDD Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. 8 L10 12 nH C10 30 pF L7 18 nH L8 DNI AUX IN J5 SMA C26 3.3 pF 203510-003 Figure 3. SKY13713-21 Evaluation Board Schematic Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 8 May 10, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203510B DATA SHEET • SKY13713-21: RX DIVERSITY FEM Figure 4. SKY13713-21 Evaluation Board Assembly Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203510B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 10, 2016 9 DATA SHEET • SKY13713-21: RX DIVERSITY FEM 3.3 20X 0.3 16X 0.55 Pin 24 Pin 1 Indicator 0.2 X 0.2 Pin 1 12X 0.55 Pitch 0.5 4.3 4X 0.425 Exposed Center Pad Stencil Aperture Size of 80% to 100% of the Module/Package Solder Mask Openings Package Outline 4X 0.5 Stencil Aperture (Top View) 3.3 Pin 1 3.4 Pin 24 0.25 Min. 8X 0.55 8X 0.3 Pin 24 20X 0.4 16X 0.65 Pin 1 Indicator 0.2 X 0.2 Pin 1 12X 0.65 Pitch 0.5 4.4 4.3 Pitch 0.5 2X 1 Pitch 0.6 Exposed Center Pad Opening Size of 60% to 100% of the Exposed Center Opening Shown Thermal Via Array Ø0.3 mm on 0.6 mm Pitch will Improve Thermal Performance 2X 0.5 Package Outline 0.6 Pitch Metallization (Top View) Package Outline Solder Mask Opening (Top View) Notes: 1. Thermal vias should be resin filled and capped in accordance with IPC-4761 Type VII vias. 30 to 35 µm Cu thickness is recommended. 2. All measurements are in millimeters. 203510-005 Figure 5. SKY13713-21 PCB Layout Footprint Pin 1 Indicator SKYWORKS Skyworks Part Number Lot Code Date / Country Code 203510-006 Figure 6. Typical Part Markings (Top View) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 10 May 10, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203510B DATA SHEET • SKY13713-21: RX DIVERSITY FEM Solder Mask Opening 0.2 A B C See Detail C 24X SMT Pad B 0.1 M A B C Top C 0 4 A 4X 0.25 0 3 4X 0.75 16X 1.4 Top View Bottom View Side View 0.35 ± 0.1 2.4 0.3 ± 0.1 (0.1) 0.4 ± 0.05 4X 0.25 0.1 (0.1) 0.3 ± 0.1 5X R0.05 Max (0.1) 0.3 ± 0.05 1.4 Metal Pad Edge Metal Pad Edge Detail C SMT Pad Scale: 2X 1X This Rotation 1X Rotated 180º 1X Rotated 90º CW 1X Rotated 90º CCW SMT Pad Scale: 2X 4X This Rotation 4X Rotated 180º 6X Rotated 90º CW 6X Rotated 90º CCW 0.3 X 0.3 Solder Mask Edges Detail B Detail A 4X 0.75 0.65 ± 0.05 4X 1.25 0.075 A B C 12X 1.9 Pin 1 Indicator Pin 24 Pin 1 Indicator Pin 1 B A Center Pad Scale: Full 1X This Rotation Notes: 1. Dimensions and tolerances according to ASME Y14.5M-1994. 2. Dimensions are in millimeters. 203510-007 4.00 ±0.10 2.00 ±0.05 5.50 ±0.05 B A B 12.00 ±0.30 1. –0 50 + .00 0. 10 4.24 ±0.05 0.30 ±0.05 1.75 ±0.1 Figure 7. SKY13713-21 Package Dimensions A Pin 1 Ø 8.00 ±0.10 1.00 ±0.10 0.90 ±0.05 Section B 3.24 ±0.05 Notes: 1. 2. 3. 4. 5. 10-sprocket hole pitch cumulative tolerance: ±0.2 mm. Camber not to exceed 1 mm in 250 mm. Carrier tape: black conductive polystyrene. Ao and Bo measured on a plane 0.3 mm from bottom of pocket. Ko measured from a plane on the inside bottom of the pocket to the top surface of the carrier. 6. Pocket position relative to sprocket hole measured as true position of pocket, not pocket hole. 7. Pocket center and pocket hole center must be the same position. 8. All dimensions are in millimeters. Section A 203510-008 Figure 8. SKY13713-21 Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203510B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 10, 2016 11 DATA SHEET • SKY13713-21: RX DIVERSITY FEM Ordering Information Model Name SKY13713-21: RX Diversity FEM Manufacturing Part Number SKY13713-21 Evaluation Board Part Number TW22-D405-001 Copyright © 2016 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks and the Skyworks symbol are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 12 May 10, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203510B