SKMM WTS SRD Rev. 1.01:2007 TECHNICAL SPECIFICATION FOR SHORT RANGE DEVICES (SRD) Suruhanjaya Komunikasi dan Multimedia Malaysia Off Pesiaran Multimedia, 63000 Cyberjaya, Selangor Darul Ehsan, Malaysia Copyright of SKMM, 2007 SKMM WTS SRD Rev. 1.01:2007 FOREWORD This Technical Specification was developed under the authority of the Malaysian Communications and Multimedia Commission (SKMM) under the Communications and Multimedia Act 1998 (CMA 98) and the relevant provisions on technical regulation of Part VII of the CMA 98. It is based on recognised International Standards documents. This Technical Specification specifies the specification to conform for approval of telecommunications device. NOTICE This Specification is subject to review and revision i SKMM WTS SRD Rev. 1.01:2007 CONTENTS Page Foreword................................................................................................................... i 1 Scope........................................................................................................................ 1 2 Normative references ............................................................................................... 1 3 Abbreviations ............................................................................................................ 1 4 4.1 4.2 Requirements ........................................................................................................... General requirements............................................................................................... Technical requirements ............................................................................................ 2 2 3 Technical requirements for Short Range Devices (SRD)......................................... 4 Tables 1 Annexes A Normative reference ................................................................................................. ii 8 SKMM WTS SRD Rev. 1.01:2007 TECHNICAL SPECIFICATION FOR SHORT RANGE DEVICES (SRD) 1. Scope 1.1 This specification defines the minimum technical requirements for SRD transmitters and receivers operating in frequencies as defined in Issuance of Class Assignment and Standard Radio System Plan (SRSP). 1.2 SRD may be fixed, mobile or portable stations that come with a radio frequency output connector and dedicated antenna or an integral antenna. Applications include Short Range Communication (SRC) device, remote control device, security device, wireless microphone device, wireless local area network (WLAN), Industrial, Scientific and Medical (ISM) device and radio frequency identification device (RFID). These devices may employ different types of modulation and may have speech application. 2. Normative references 2.1 The following normative references are indispensable for the application of this Technical Specification. For dated references, only the edition cited applies. For undated references, the latest edition of the normative references (including any amendments) applies. 2.2 The devices shall be tested for compliance with the applicable technical requirements stipulated in Clause 4 and Table 1 of this Technical Specification. The test methods and conditions given in one or more of the following references may be applicable to the device under test (refer to Table 1 for guidance). See Annex A 3. Abbreviations AC Alternating Current DC Direct Current EIRP Effective Isotropic Radiated Power ETSI European Telecommunications Standards Institute FCC Federal Communications Commission IEC International Electrotechnical Commission 1 SKMM WTS SRD Rev. 1.01:2007 ISM Industrial, Scientific and Medical RFID Radio Frequency Identification Device SKMM Malaysian Communications and Multimedia Commission SRSP Standard Radio System Plan SRD Short Range Devices SRC Short Range Communication WLAN Wireless Local Area Network 4. Requirements 4.1 General requirements SRD shall be designed to meet the following basic requirements: a) The device is intended for operating in unprotected and shared frequency bands. Its operation shall not cause interference with other authorised radio-communication services, and be able to tolerate any interference caused by other radio-communication services, electrical or electronic equipment. b) The device shall not be constructed with any external or readily accessible control which permits the adjustments of its operation in a manner that is inconsistent with this Technical Specification. 4.1.1 Power supply requirements The equipment may be AC or DC powered. For AC powered equipment, the operating voltage shall be 240 V +5 %, -10 % and frequency 50 Hz ± 1 % as according to MS 406 or 230 V ± 10 % and frequency 50 Hz ± 1 % as according to MS IEC 60038 whichever is current. Where external power supply is used, e.g AC adaptor, it shall not affect the capability of the equipment to meet this specification. Adaptor must be pre-approved by the relevant regulatory body before it can be used with the equipment. 4.1.2 Power supply cord and mains plug requirements The equipment shall be fitted with a suitable and appropriate approved power supply cord and mains plug. Both are regulated products and must be pre-approved by the relevant regulatory body before it can be used with the equipment. The power supply cord shall be certified as according to: a) MS 140; or 2 SKMM WTS SRD Rev. 1.01:2007 b) BS 6500; or c) IEC 60227-5; or d) IEC 60245-4. The main plug shall be certified as according to: a) 13 A fused plugs: MS 589: Part 1 or BS 1363: Part 1; or b) 2.5 A, 250 V, flat non-rewirable two-pole plugs: MS 1578 or BS EN 50075. 4.1.3 Marking Requirements The equipment shall be marked with the following information: a) supplier/manufacturer’s name or identification mark; b) supplier/manufacturer’s model or type reference; and c) other markings as required by the relevant standards. The markings shall be legible, indelible and readily visible. All information on the marking shall be either in Bahasa Melayu or English Language. 4.2 Technical Requirements The SRD shall comply with the maximum Effective Isotropic Radiated Power (EIRP) and Transmitter & Receiver Spurious Emissions given in Table 1, operating in its intended frequency band or frequencies. It shall fulfil the relevant requirements of this Technical Specification on all the permitted frequencies which it is intended to operate. 3 SKMM WTS SRD Rev. 1.01:2007 SKMM WTS SRD Rev. 1.01:2007 Table 1. Technical Requirements for Short Range Devices (SRD) Maximum EIRP 50 mWatt Transmitter & Receiver Spurious Emissions EN 300-330-1 Test Reference 1. Authorized Frequency Bands/Frequencies 3.0000 kHz to 195.0000 kHz EN 300-330-1 Security device 2. 6765.0000 kHz to 6795.0000 kHz 100 mWatt 500 mWatt 100 mWatt FCC Part 15 / EN 300-330-1 FCC Part 15 / EN 300-330-1 FCC Part 15 / EN 300 330-1 FCC Part 15 / EN 300 220-1 EN 300 220-1 FCC Part 15 / EN 300 330-1 FCC Part 15 / EN 300 220-1 EN 300 220-1 SRC device ISM SRC device FCC Part 15 / EN 300 220-1 EN 300 220-1 Wireless microphone device 3. 13.5530 MHz to 13.5670 MHz 500 mWatt 4. 26.9570 MHz to 27.2830 MHz 100 mWatt SRD Applications ISM SRC device 4 500 mWatt 5. 26.95728 MHz to 27.28272 MHz 50 mWatt FCC Part 15 / EN 300 220-1 EN 300 220-1 6. 26.9650 MHz to 27.2750 MHz 50 mWatt EN 300 220-1 EN 300 220-1 Remote control device 7. 40.0000 MHz 50 mWatt EN 300 220-1 EN 300 220-1 Remote control device 8. 40.4350 MHz to 40.9250 MHz 50 mWatt EN 300 220-1 EN 300 220-1 Wireless microphone device 1 ISM Remarks SKMM WTS SRD Rev. 1.01:2007 Table 1. Technical Requirements for Short Range Devices (SRD) (continued) Authorized Frequency Bands/Frequencies 10. 47.0000 MHz 50 mWatt Transmitter & Receiver Spurious Emissions FCC Part 15 / EN 300 220-1 FCC Part 15 / EN 300 220-1 EN 300 220-1 11. 49.0000 MHz 50 mWatt EN 300 220-1 EN 300 220-1 Remote control device 12. 13. 87.5000 MHz to 108.0000 MHz 182.0250 MHz to 182.9750 MHz 50 mWatt 50 mWatt 183.0250 MHz to 183.4750 MHz 50 mWatt 15. 16. 17. 18. 217.0250 MHz to 217.9750 MHz 218.0250 MHz to 218.4750 MHz 228.0063 MHz to 228.9937 MHz 303.0000 MHz to 320.0000 MHz 50 mWatt 50 mWatt 50 mWatt 50 mWatt EN 300 220-1 FCC Part 15 / EN 300 220-1 FCC Part 15 / EN 300 220-1 EN 300 220-1 EN 300 220-1 EN 300 220-1 EN 300 220-1 Wireless microphone device Wireless microphone device 14. EN 300 220-1 FCC Part 15 / EN 300 220-1 FCC Part 15 / EN 300 220-1 EN 300 220-1 EN 300 220-1 EN 300 220-1 EN 300 220-1 9. Maximum EIRP 100 mWatt 40.6600 MHz to 40.7000 MHz 500 mWatt Test Reference SRD Applications FCC Part 15 / EN 300 220-1 FCC Part 15 / EN 300 220-1 EN 300 220-1 SRC device Remarks ISM Remote control device 5 Wireless microphone device Wireless microphone device Security device Remote control device, Security device SKMM WTS SRD Rev. 1.01:2007 2 Wireless microphone device SKMM WTS SRD Rev. 1.01:2007 SKMM WTS SRD Rev. 1.01:2007 Table 1. Technical Requirements for Short Range Devices (SRD) (continued) 6 Maximum EIRP 50 mWatt 50 mWatt Transmitter & Receiver Spurious Emissions EN 300 220-1 EN 300 220-1 Test Reference SRD Applications 19. 20. Authorized Frequency Bands/Frequencies 400.0000 MHz to 402.0000 MHz 433.0000 MHz to 435.0000 MHz EN 300 220-1 EN 300 220-1 21. 22. 510.0000 MHz to 798.0000 MHz 868.1000 MHz 100 mWatt 50 mWatt 50 mWatt 23. 24. 919.0000 MHz to 923.0000 MHz 2400.0000 MHz to 2500.0000 MHz 25. 26. 5150.0000 MHz to 5250.0000 MHz 5250.0000 MHz to 5350.0000 MHz EN 300 220-1 EN 300 220-1 EN 300 220-1 / ETSI TR 101445 FCC Part 15 EN 300 440-1 EN 300 328 EN 300 440-1 FCC Part 15 EN 300 220-1 EN 300 220-1 EN 300 220-1 / ETSI TR 101445 FCC Part 15 EN 300 440-1 EN 300 328 EN 300 440-1 FCC Part 15 Security device Remote control device, Security device SRC device Wireless microphone device Security device 2 Watt 500 mWatt 1 Watt 1 Watt 3 RFID SRC device ISM SRC device, WLAN SRC device, WLAN Remarks SRSP 530 SRSP 534 SRSP 534 SKMM WTS SRD Rev. 1.01:2007 Table 1. Technical Requirements for Short Range Devices (SRD) (continued) 28. 24.0000 GHz to 24.2500 GHz 29 61.0000 GHz to 61.5000 GHz 30. 76.0000 GHz to 77.0000 GHz 31. 122.0000 GHz to 123.0000 GHz 32. 244.0000 GHz to 246.0000 GHz 7 27. Authorized Frequency Bands/Frequencies 5725.0000 MHz to 5875.0000 MHz Maximum EIRP 500 mWatt 1 Watt 500 mWatt 1 Watt 500 mWatt 1 Watt 50 mWatt Transmitter & Receiver Spurious Emissions FCC Part 15 / EN 300 440-1 FCC Part 15 FCC Part 15 / EN 300 440-1 Test Reference FCC Part 15 FCC Part 15 FCC Part 15 / EN 301 091 FCC Part 15 / EN 301 091 FCC Part 15 / EN 300 440-1 FCC Part 15 FCC Part 15 / EN 300 440-1 500 mWatt 1 Watt 500 mWatt 1 Watt SRC Applications Remarks ISM SRC device ISM SRC device ISM SRC device Security device ISM SRC device ISM SRC device SKMM WTS SRD Rev. 1.01:2007 4 SKMM WTS SRD Rev. 1.01:2007 Annex A (normative) Normative references BS 1363: Part 1 13 A plugs, socket-outlets, adaptors and connection units – Part 1: Specification for rewirable and non-rewirable 13 A fused plugs BS 6500 Electric cables Flexible cords rated up to 300/500 V, for use with appliances and equipment intended for domestic, office and similar environments BS EN 50075 Specification for flat non-wirable two-pole plugs 2.5 A 250 V, with cord, for the connection of Class II-equipment for household and similar purposes ETSI TR 101 445 Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD) intended for operation in the 862 MHz to 870 MHz band; System Reference Document for Radio Frequency Identification (RFID) equipment ETSI EN 300 220-1 Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Radio Equipment to be used in the 25 MHz to 1000 MHz frequency range with the power levels ranging up to 500 mW – Part 1: Technical characteristics and test method ETSI EN 300 330-1 Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Radio equipment in the frequency rang 9 kHz to 25 MHz and inductive loop systems in the frequency range 9 kHz to 30 MHz – Part 1: Technical characteristics and test methods ETSI EN 300 440-1 Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Radio equipment to be used in the 1 GHz to 40 GHz frequency range – Part 1: Technical characteristics and test methods ETSI EN 300 328 Electromagnetic compatibility and Radio spectrum Matters (ERM); wideband transmission systems; Data transmission equipment operating in the 2.4 GHz ISM band and using spread spectrum modulation techniques; Harmonised EN covering essential requirements under article 3.2 of the R&TTE Directives 8 SKMM WTS SRD Rev. 1.01:2007 ETSI EN 301 091 Electromagnetic compatibility and Radio spectrum Matters (ERM); Road Transport and Traffic Telematics (RTTT); Technical characteristics and test methods for radar equipment operating in the 76 GHz to 77 GHz band FCC Part 15 Radio Frequency Devices IEC 60245-4 Rubber insulated cables – Rated voltages up to and including 450/750 V – Part 4: Cords and flexible cables IEC 60227-5 Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V – Part 5: Flexible cables (cords) MS 140 Specification for insulated flexible cords and cables MS 589: Part 1 Specification for 13 A plugs, socket outlets, adaptors and connection units – Part 1: Specification for rewirable and nonrewirable 13 A fused plugs MS 1578 Specification for flat non-rewirable two-pole plugs, 2.5 A, 250 V, with cord, for the connection of class II-Equipment for household and similar purposes MCMC SRSP - 534 WLAN Requirements for wireless local area networks (WLAN) systems operating in the frequency band 5150 MHz to 5350 MHz MCMC SRSP - 530 RFID Requirement for Radio Frequency Identification Device operating in the frequency band from 919 MHz to 923 MHz P.U (B) 416 Communications and Multimedia Act; Notification of Issuance of Class Assignment MS IEC 60038 IEC Standard voltages MS IEC 60950-1 Information Technology equipment – Safety MS IEC CISPR 22 Information Technology Equipment – Radio disturbance characteristics – Limits and methods of measurement 9