w
WM9713L
AC’97 Audio + Touchpanel CODEC
DESCRIPTION
The WM9713L is a highly integrated input/output device
designed for mobile computing and communications.
The chip is architected for dual CODEC operation, supporting
hi-fi stereo CODEC functions via the AC link interface, and
additionally supporting voice CODEC functions via a PCM type
Synchronous Serial Port (SSP). A third, auxiliary DAC is
provided which may be used to support generation of
supervisory tones, or ring-tones at different sample rates to the
main CODEC.
The device can connect directly to a 4-wire or 5-wire touchpanel, mono or stereo microphones, stereo headphones and a
stereo speaker, reducing total component count in the system.
Cap-less connections to the headphones, speakers, and
earpiece may be used, saving cost and board area. Additionally,
multiple analogue input and output pins are provided for
seamless integration with analogue connected wireless
communication devices.
All device functions are accessed and controlled through a
single AC-Link interface compliant with the AC’97 standard. The
24.576MHz masterclock can be input directly or generated
internally from a 13MHz (or other frequency) clock by an on-chip
PLL. The PLL supports a wide range of input clock from
2.048MHz to 78.6MHz.
The WM9713L operates at supply voltages from 1.8V to 3.6V.
Each section of the chip can be powered down under software
control to save power. The device is available in a small
leadless 7x7mm QFN package, ideal for use in hand-held
portable systems.
FEATURES
AC’97 Rev 2.2 compatible stereo CODEC
- DAC SNR 94dB, THD –85dB
- ADC SNR 87dB, THD –86dB
- Variable Rate Audio, supports all WinCE sample rates
- Tone Control, Bass Boost and 3D Enhancement
On-chip 45mW headphone driver
On-chip 400mW mono or stereo speaker drivers
Stereo, mono or differential microphone input
- Automatic Level Control (ALC)
- Mic insert and mic button press detection
Auxiliary mono DAC (ring tone or DC level generation)
Seamless interface to wireless chipset
Resistive touchpanel interface
- Supports 4-wire and 5-wire panels
- 12-bit resolution, INL 2 LSBs (<0.5 pixels)
- X, Y and touch-pressure (Z) measurement
- Pen-down detection supported in Sleep Mode
2
Additional PCM/I S interface to support voice CODEC
PLL derived audio clocks.
Supports input clock ranging from 2.048MHz to 78.6MHz
1.8V to 3.6V supplies (digital down to 1.62V, speaker up to
4.2V)
7x7mm 48-lead QFN package
APPLICATIONS
Smartphones
Personal Digital Assistants (PDA)
Handheld and Tablet Computers
BLOCK DIAGRAM
WOLFSON MICROELECTRONICS plc
To receive regular email updates, sign up at http://www.wolfsonmicro.com/enews
Pre-Production, November 2011, Rev 3.3
Copyright 2011 Wolfson Microelectronics plc
WM9713L
Pre-Production
TABLE OF CONTENTS
DESCRIPTION ....................................................................................................... 1 FEATURES ............................................................................................................ 1 APPLICATIONS..................................................................................................... 1 BLOCK DIAGRAM ................................................................................................ 1 TABLE OF CONTENTS ......................................................................................... 2 PIN CONFIGURATION .......................................................................................... 4 ORDERING INFORMATION .................................................................................. 4 PIN DESCRIPTION ................................................................................................ 5 ABSOLUTE MAXIMUM RATINGS ........................................................................ 6 RECOMMENDED OPERATING CONDITIONS ..................................................... 7 ELECTRICAL CHARACTERISTICS ..................................................................... 8 AUDIO OUTPUTS ............................................................................................................ 8 AUDIO INPUTS ................................................................................................................ 9 AUXILIARY MONO DAC (AUXDAC) ................................................................................ 9 PCM VOICE DAC (VXDAC) ............................................................................................. 9 TOUCHPANEL AND AUXILIARY ADC .......................................................................... 10 COMPARATORS ........................................................................................................... 10 REFERENCE VOLTAGES ............................................................................................. 10 DIGITAL INTERFACE CHARACTERISTICS ................................................................. 11 POWER CONSUMPTION .................................................................................... 11 SIGNAL TIMING REQUIREMENTS .................................................................... 12 AC97 INTERFACE TIMING............................................................................................ 12 PCM AUDIO INTERFACE TIMING – SLAVE MODE ..................................................... 16 PCM AUDIO INTERFACE TIMING – MASTER MODE ................................................. 17 DEVICE DESCRIPTION ...................................................................................... 18 INTRODUCTION ............................................................................................................ 18 AUDIO PATHS OVERVIEW ........................................................................................... 20 CLOCK GENERATION .................................................................................................. 21 CLOCK DIVISION MODES ............................................................................................ 21 PLL MODE ..................................................................................................................... 24 DIGITAL INTERFACES .................................................................................................. 27 AC97 INTERFACE ......................................................................................................... 27 PCM INTERFACE .......................................................................................................... 28 AUDIO ADCS ...................................................................................................... 33 STEREO ADC ................................................................................................................ 33 RECORD SELECTOR.................................................................................................... 34 RECORD GAIN .............................................................................................................. 35 AUTOMATIC LEVEL CONTROL.................................................................................... 37 AUDIO DACS ...................................................................................................... 40 STEREO DAC ................................................................................................................ 40 VOICE DAC .................................................................................................................... 43 AUXILIARY DAC ............................................................................................................ 44 VARIABLE RATE AUDIO / SAMPLE RATE CONVERSION .............................. 46 AUDIO INPUTS.................................................................................................... 47 LINE INPUT .................................................................................................................... 47 MICROPHONE INPUT ................................................................................................... 48 MONOIN INPUT ............................................................................................................. 54 PCBEEP INPUT ............................................................................................................. 56 DIFFERENTIAL MONO INPUT ...................................................................................... 56 w
PP, Rev 3.3, November 2011
2
Pre-Production
WM9713L
AUDIO MIXERS ................................................................................................... 57 MIXER OVERVIEW ........................................................................................................ 57 HEADPHONE MIXERS .................................................................................................. 57 SPEAKER MIXER .......................................................................................................... 57 MONO MIXER ................................................................................................................ 58 MIXER OUTPUT INVERTERS ....................................................................................... 58 ANALOGUE AUDIO OUTPUTS .......................................................................... 59 HEADPHONE OUTPUTS – HPL AND HPR .................................................................. 59 MONO OUTPUT ............................................................................................................ 60 SPEAKER OUTPUTS – SPKL AND SPKR .................................................................... 61 AUXILIARY OUTPUTS – OUT3 AND OUT4 .................................................................. 62 THERMAL SENSOR ...................................................................................................... 63 JACK INSERTION AND AUTO-SWITCHING ................................................................ 65 DIGITAL AUDIO (S/PDIF) OUTPUT .................................................................... 68 TOUCHPANEL INTERFACE ............................................................................... 70 PRINCIPLE OF OPERATION - FOUR-WIRE TOUCHPANEL ....................................... 71 PRINCIPLE OF OPERATION - FIVE-WIRE TOUCHPANEL ......................................... 73 CONTROLLING THE TOUCHPANEL DIGITISER ......................................................... 75 ADDITIONAL FEATURES ................................................................................... 84 AUXILIARY ADC INPUTS .............................................................................................. 84 BATTERY ALARM AND ANALOGUE COMPARATORS ............................................... 85 GPIO AND INTERRUPT CONTROL .............................................................................. 88 POWER MANAGEMENT ..................................................................................... 92 INTRODUCTION ............................................................................................................ 92 AC97 CONTROL REGISTER......................................................................................... 92 EXTENDED POWERDOWN REGISTERS .................................................................... 93 ADDITIONAL POWER MANAGEMENT......................................................................... 95 POWER ON RESET (POR) ........................................................................................... 95 REGISTER MAP .................................................................................................. 96 REGISTER BITS BY ADDRESS .................................................................................... 97 APPLICATIONS INFORMATION ...................................................................... 128 RECOMMENDED EXTERNAL COMPONENTS .......................................................... 128 LINE OUTPUT .............................................................................................................. 129 AC-COUPLED HEADPHONE OUTPUT ...................................................................... 129 DC COUPLED (CAPLESS) HEADPHONE OUTPUT .................................................. 130 BTL LOUDSPEAKER OUTPUT ................................................................................... 130 COMBINED HEADSET / BTL EAR SPEAKER ............................................................ 131 COMBINED HEADSET / SINGLE-ENDED EAR SPEAKER ........................................ 131 JACK INSERT DETECTION ........................................................................................ 132 HOOKSWITCH DETECTION ....................................................................................... 132 TYPICAL OUTPUT CONFIGURATIONS ..................................................................... 133 PACKAGE DIMENSIONS .................................................................................. 136 IMPORTANT NOTICE ....................................................................................... 137 ADDRESS: ................................................................................................................... 137 REVISION HISTORY ......................................................................................... 138 w
PP, Rev 3.3, November 2011
3
WM9713L
Pre-Production
PIN CONFIGURATION
ORDERING INFORMATION
DEVICE
TEMPERATURE
RANGE
WM9713CLGEFL/V
-25 to +85 C
WM9713CLGEFL/RV
-25 to +85 C
o
o
PACKAGE
MOISTURE SENSITIVITY
LEVEL
PEAK SOLDERING
TEMPERATURE
48-lead QFN
(Pb-free)
MSL3
260 C
48-lead QFN
(Pb-free, tape and reel)
MSL3
260 C
o
o
Note:
Reel quantity = 2,200
w
PP, Rev 3.3, November 2011
4
WM9713L
Pre-Production
PIN DESCRIPTION
PIN
NAME
TYPE
1
DBVDD
Supply
2
MCLKA
Digital Input
Master Clock A Input
3
MCLKB / GPIO6 / (ADA / MASK)
Digital In/Out
Master Clock B Input / GPIO6 / (ADA output / MASK input)
4
DGND1
Supply
Digital Ground (return path for both DCVDD and DBVDD)
5
SDATAOUT
Digital Input
6
BITCLK
Digital Output
7
DGND2
Supply
8
SDATAIN
Digital Output
9
DCVDD
Supply
10
SYNC
Digital Input
11
RESETB / GPIO7 / (PENDOWN)
Digital In / Out
12
WIPER / AUX4 / GPIO8 / (S/PDIF) Analogue In / Out
DESCRIPTION
Digital I/O Buffer Supply
Serial Data Output from Controller / Input to WM9713L
Serial Interface Clock Output to Controller
Digital Ground (return path for both DCVDD and DBVDD)
Serial Data Input to Controller / Output from WM9713L
Digital Core Supply
Serial Interface Synchronisation Pulse from Controller
Reset (asynchronous, active Low, resets all registers to their
default) / GPIO7 / (pen down output)
Top Sheet Connection for 5-wire Touchpanels / Auxiliary ADC
input / GPIO8 / (S/PDIF digital audio output)
Touchpanel Driver Supply
13
TPVDD
Supply
14
X+/ BR
Analogue Input
Touchpanel Connection: X+ (Right) for 4-wire / bottom right for 5wire
15
Y+/TR
Analogue Input
Touchpanel Connection: Y+ (Top) for 4-wire / top right for 5-wire
16
X-/TL
Analogue Input
Touchpanel Connection: X- (Left) for 4-wire / top left for 5-wire
17
Y-/BL
Analogue Input
Touchpanel Connection: Y- (Bottom) for 4-wire / bottom left for 5wire
Touchpanel Driver Ground
18
TPGND
Supply
19
PCBEEP
Analogue Input
Line Input to analogue audio mixers, typically used for beeps
20
MONOIN
Analogue Input
Mono Input (RX)
21
MIC1
Analogue Input
Microphone preamp A input 1
22
MICCM
Analogue Input
Microphone common mode input
23
LINEL
Analogue Input
Left Line Input
24
LINER
Analogue Input
Right Line Input
25
AVDD
Supply
Analogue Supply (audio DACs, ADCs, PGAs, mic amps, mixers)
26
AGND
Supply
Analogue Ground
27
VREF
Analogue Output
Internal Reference Voltage (buffered CAP2)
28
MICBIAS
Analogue Output
Bias Voltage for Microphones (buffered CAP2 1.8)
29
MIC2A / COMP1 / AUX1
Analogue Input
Microphone preamp A input 2 / COMP1 input / Auxiliary ADC input
30
MIC2B / COMP2 / AUX2
Analogue Input
Microphone preamp B input / COMP2 input / Auxiliary ADC input
31
MONO
Analogue output
Mono output driver (line or headphone)
32
CAP2
Analogue In / Out
Internal Reference Voltage (normally AVDD/2, if not overdriven)
33
OUT4
Analogue Output
Auxiliary output driver (speaker, line or headphone)
34
SPKGND
Supply
35
SPKL
Analogue Output
Left speaker driver (speaker, line or headphone)
36
SPKR
Analogue Output
Right speaker driver (speaker, line or headphone)
37
OUT3
Analogue Output
Auxiliary output driver (speaker, line or headphone)
38
SPKVDD
Supply
39
HPL
Analogue Output
40
HPGND
Supply
41
HPR
Analogue Output
42
AGND2
Supply
Analogue ground, chip substrate
43
HPVDD
Supply
Headphone supply (feeds output buffers on pins 39 and 41)
w
Speaker ground (feeds output buffers on pins 33, 35, 36 and 37)
Speaker supply (feeds output buffers on pins 33, 35, 36 and 37)
Headphone left driver (line or headphone)
Headphone ground (feeds output buffers on pins 39 and 41)
Headphone right driver (line or headphone)
PP, Rev 3.3, November 2011
5
WM9713L
Pre-Production
44
GPIO1 / PCMCLK
Digital In / Out
GPIO Pin 1 / PCM interface clock
45
GPIO2 / IRQ
Digital In / Out
GPIO Pin 2 / IRQ (Interrupt Request) output
46
GPIO3 / PENDOWN / PCMFS
Digital In / Out
GPIO Pin 3 / pen down output or PCM frame signal
47
GPIO4 / ADA / MASK / PCMDAC
Digital In / Out
GPIO Pin 4 / ADA (ADC data available) output or Mask input /
PCM input (DAC) data
48
GPIO5 / S/PDIF / PCMADC
Digital In / Out
GPIO Pin 5 / S/PDIF digital audio output / PCM output (ADC) data
49
GND_PADDLE
Die Paddle (Note 1)
Note:
1.
It is recommended that the GND_PADDLE is connected to analogue ground. Refer to the "Recommended External
Components" diagram and "Package Dimensions" section for further information.
ABSOLUTE MAXIMUM RATINGS
Absolute Maximum Ratings are stress ratings only. Permanent damage to the device may be caused by continuously operating at
or beyond these limits. Device functional operating limits and guaranteed performance specifications are given under Electrical
Characteristics at the test conditions specified.
ESD Sensitive Device. This device is manufactured on a CMOS process. It is therefore generically susceptible to
damage from excessive static voltages. Proper ESD precautions must be taken during handling and storage of
this device.
Wolfson tests its package types according to IPC/JEDEC J-STD-020B for Moisture Sensitivity to determine acceptable storage
conditions prior to surface mount assembly. These levels are:
MSL1 = unlimited floor life at <30C / 85% Relative Humidity. Not normally stored in moisture barrier bag.
MSL2 = out of bag storage for 1 year at <30C / 60% Relative Humidity. Supplied in moisture barrier bag.
MSL3 = out of bag storage for 168 hours at <30C / 60% Relative Humidity. Supplied in moisture barrier bag.
The Moisture Sensitivity Level for each package type is specified in Ordering Information.
CONDITION
MIN
MAX
Digital supply voltages (DCVDD, DBVDD)
-0.3V
+3.63V
Analogue supply voltages (AVDD, HPVDD, TPVDD)
-0.3V
+3.63V
Speaker supply voltage (SPKVDD)
-0.3V
Touchpanel supply voltage (TPVDD)
+4.2V
AVDD +0.3V
Voltage range digital inputs
DGND -0.3V
DBVDD +0.3V
Voltage range analogue inputs
AGND -0.3V
AVDD +0.3V
Voltage range touchpanel Inputs X+, X-, Y+ and Y-
TPVDD +0.3V
Voltage range touchpanel Inputs X+, X-, Y+ and YOperating temperature range, TA
w
AVDD +0.3V
o
-25 C
o
+85 C
PP, Rev 3.3, November 2011
6
WM9713L
Pre-Production
RECOMMENDED OPERATING CONDITIONS
PARAMETER
SYMBOL
MIN
TYP
MAX
UNIT
Digital input/output buffer supply
range
DBVDD
1.71
3.3
3.6
V
Digital core supply range
Analogue supply range
Speaker supply range
Digital ground
Analogue ground
TEST CONDITIONS
DCVDD
1.71
1.8
3.6
V
AVDD, HPVDD,
TPVDD
1.8
3.3
3.6
V
SPKVDD
1.8
3.3
4.2
V
DGND1, DGND2
0
V
AGND, HPGND,
SPKGND, TPGND
0
V
Difference AGND to DGND
Note 1
-0.3
0
+0.3
V
Notes:
1. AGND is normally the same as DGND1/DGND2
2. DCVDD <= DBVDD and DCVDD <= AVDD
3. DCVDD should be >=2V when using the PLL
w
PP, Rev 3.3, November 2011
7
WM9713L
Pre-Production
ELECTRICAL CHARACTERISTICS
AUDIO OUTPUTS
Test Conditions
o
DBVDD=3.3V, DCVDD = 3.3V, AVDD=HPVDD=SPKVDD =3.3V, TA = +25 C, 1kHz signal, fs = 48kHz, 24-bit audio data unless
otherwise stated.
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
TYP
MAX
UNIT
DAC to Line-Out (HPL/R, SPKL/R or MONO with 10k / 50pF load)
Full-scale output (0dBFS)
Signal to Noise Ratio
AVDD = 3.3V, PGA gains
set to 0dB
SNR
85
1
V rms
94
dB
(A-weighted)
Total Harmonic Distortion
Power Supply Rejection
THD
-3dB output
-85
PSRR
100mV, 20Hz to 20kHz
signal on AVDD
50
-74
dB
dB
Speaker Output (SPKL/SPKR with 8 bridge tied load, INV=1)
Output Power at 1% THD
Abs. max output power
Total Harmonic Distortion
Signal to Noise Ratio
PO
THD = 1%
POmax
THD
PO = 200mW
SNR
400
mW (rms)
500
mW (rms)
-66
dB
0.05
%
90
dB
(A-weighted)
Stereo Speaker Output (SPKL/OUT4 and SPKR/OUT3 with 8 bridge tied load, INV=1)
Output Power at 1% THD
Abs. max output power
Total Harmonic Distortion
Signal to Noise Ratio
PO
THD = 1%
POmax
THD
PO = 200mW
SNR
400
mW (rms)
500
mW (rms)
-66
dB
0.05
%
90
dB
(A-weighted)
Headphone Output (HPL/R, OUT3/4 or SPKL/SPKR with 16 or 32 load)
Output Power per channel
PO
Total Harmonic Distortion
THD
Signal to Noise Ratio
SNR
Output power is very closely correlated with THD; see below.
PO=10mW, RL=16
-80
PO=10mW, RL=32
-80
PO=20mW, RL=16
-78
PO=20mW, RL=32
-79
dB
90
dB
(A-weighted)
Note:
1.
All THD values are valid for the output power level quoted above – for example, at HPVDD=3.3V and RL=16, THD is
–80dB when output power is 10mW. Higher output power is possible, but will result in deterioration in THD.
w
PP, Rev 3.3, November 2011
8
WM9713L
Pre-Production
AUDIO INPUTS
Test Conditions
o
DBVDD=3.3V, DCVDD = 3.3V, AVDD = 3.3V, TA = +25 C, 1kHz signal, fs = 48kHz, 24-bit audio data unless otherwise stated.
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
TYP
MAX
UNIT
LINEL/R, MIC1/2A/2B, MONOIN and PCBEEP pins
Full Scale Input Signal Level
AVDD = 3.3V
1.0
AVDD = 1.8V
0.545
differential input mode
(MS = 01) AVDD = 3.3V
0.5
differential input mode
(MS = 01) AVDD = 1.8V
0.273
VINFS
(0dBFS)
Input Resistance
RIN
Vrms
0dB PGA gain
25.6
32
38.4
12dB PGA gain
10.4
13
15.6
Input Capacitance
k
5
pF
87
dB
Line input to ADC (LINEL, LINER, MONOIN)
Signal to Noise Ratio
SNR
80
(A-weighted)
Total Harmonic Distortion
Power Supply Rejection
THD
-3dBFS input
-86
PSRR
20Hz to 20kHz
50
-80
dB
dB
SNR
20dB boost enabled
80
dB
THD
20dB boost enabled
-80
dB
Microphone input to ADC (MIC1/2A/2B pins)
Signal to Noise Ratio
(A-weighted)
Total Harmonic Distortion
AUXILIARY MONO DAC (AUXDAC)
Test Conditions
o
DBVDD=3.3V, DCVDD = 3.3V, AVDD = 3.3V, TA = +25 C, 1kHz signal, fs = 8kHz, 24-bit audio data unless otherwise stated.
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
Resolution
Full scale output voltage
SNR
MAX
UNIT
12
bits
1
Vrms
65
71
dB
50
63
dB
AVDD=3.3V
Signal to Noise Ratio
TYP
(A-weighted)
Total Harmonic Distortion
THD
0dBFS input
PCM VOICE DAC (VXDAC)
Test Conditions
o
DBVDD=3.3V, DCVDD = 3.3V, AVDD = 3.3V, TA = +25 C, 1kHz signal, fs = 8kHz, 24-bit audio data unless otherwise stated.
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
TYP
Resolution
16
Sample rates
8
Full scale output voltage
Signal to Noise Ratio
AVDD=3.3V
MAX
UNIT
16
Ks/s
bits
1
Vrms
SNR
80
dB
THD
74
dB
(A-weighted)
Total Harmonic Distortion
w
PP, Rev 3.3, November 2011
9
WM9713L
Pre-Production
TOUCHPANEL AND AUXILIARY ADC
Test Conditions
o
DBVDD = 3.3V, DCVDD = 3.3V, AVDD = 3.3V, TA = +25 C, unless otherwise stated.
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Input Pins X+, X-, Y+, Y-, WIPER/AUX4, COMP1/AUX1, COMP2/AUX2
Input Voltage
AGND
Input leakage current
AUX pin not selected as
AUX ADC input
AVDD
<10
ADC Resolution
12
Differential Non-Linearity Error
DNL
Integral Non-Linearity Error
INL
0.25
V
nA
bits
1
LSB
2
LSB
Offset Error
4
LSB
Gain Error
6
LSB
Power Supply Rejection
PSRR
50
Channel-to-channel isolation
dB
80
Throughput Rate
DEL = 1111
dB
48
kHz
6
ms
63
k
(zero settling time)
Settling Time (programmable)
MCLK = 24.576MHz
0
Switch matrix resistance
Programmable Pull-up resistor
RPU
RPU = 000001
1
Pen down detector threshold
Pressure measurement current
20
IP
VDD/2
V
PIL = 1
400
A
PIL = 0
200
COMPARATORS
Test Conditions
o
DBVDD = 3.3V, DCVDD = 3.3V, AVDD = 3.3V, TA = +25 C, unless otherwise stated.
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
TYP
MAX
UNIT
COMP1/AUX1 and COMP2/AUX2 (pins 29, 30 – when not used as mic inputs)
Input Voltage
AGND
Input leakage current
pin not selected as AUX
ADC input
Comparator Input Offset
AVDD
<10
V
nA
-50
+50
mV
0
10.9
s
(COMP1, COMP2 only)
COMP2 delay (COMP2 only)
MCLK = 24.576MHz
REFERENCE VOLTAGES
Test Conditions
o
DBVDD=3.3V, DCVDD = 3.3V, AVDD = 3.3V, TA = +25 C, 1kHz signal, fs = 48kHz, 24-bit audio data unless otherwise stated.
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Audio ADCs, DACs, Mixers
Reference Input/Output
CAP2 pin
1.63
1.65
1.66
V
Buffered Reference Output
VREF pin
1.64
1.65
1.67
V
Bias Voltage
VMICBIAS
2.92
2.97
3.00
V
Bias Current Source
IMICBIAS
3
mA
Output Noise Voltage
Vn
Microphone Bias
w
1K to 20kHz
15
nV/Hz
PP, Rev 3.3, November 2011
10
WM9713L
Pre-Production
DIGITAL INTERFACE CHARACTERISTICS
Test Conditions
o
DBVDD = 3.3V, DCVDD = 3.3V, TA = +25 C, unless otherwise stated.
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
TYP
MAX
UNIT
DBVDD0.3
V
Digital Logic Levels (all digital input or output pins) – CMOS Levels
Input HIGH level
VIH
Input LOW level
VIL
DBVDD0.7
Output HIGH level
VOH
source current = 2mA
Output LOW level
VOL
sink current = 2mA
V
DBVDD0.9
DBVDD0.1
Clock Frequency
Master clock (MCLKA pin)
24.576
MHz
AC’97 bit clock (BIT_CLK pin)
12.288
MHz
AC’97 sync pulse (SYNC pin)
48
kHz
Notes:
1.
All audio and non-audio sample rates and other timing scales proportionately with the master clock.
2.
For signal timing on the AC-Link, please refer to the AC’97 specification (Revision 2.2)
POWER CONSUMPTION
The power consumption of the WM9713L depends on the following factors:
Supply voltages: Reducing the supply voltages also reduces digital supply currents, and therefore results in
significant power savings especially in the digital sections of the WM9713L.
Operating mode: Significant power savings can be achieved by always disabling parts of the WM9713L that are
not used (e.g. audio ADC, DAC, touchpanel digitiser).
Sample rates: Running at lower sample rates will reduce power consumption significantly. The figures below are
for 48kHz (unless otherwise specified), but in many scenarios it is not necessary to run at this frequency, e.g.
8kHz PCM voice call scenario uses only 11.4mW (see below).
MODE DESCRIPTION
AVDD
DCVDD
DBVDD
Supply
Current
Supply
Current
Supply
Current
V / mA
Off (lowest possible power)
V / mA
Total
Power
(mW)
V / mA
3.3
0.01
3.3
0
3.3
0.005
0.05
3.3
0.014
3.3
0
3.3
0.005
0.06
Touchpanel only (waiting for pen-down)
3.3
0.042
3.3
0
3.3
0.005
0.15
PCM Voice call (fs=8kHz)
2.8
2.37
2.8
1.7
2.8
0.006
11.4
Record from mono microphone
3.3
3.644
3.3 10.973 3.3
2.974
58.05
Stereo DAC Playback (AC link to headphone)
3.3
3.733
3.3
3.3
2.789
53.60
Stereo DAC Playback (AC link to headphone)
3.3
4.801
3.3 10.504 3.3
2.814
59.79
Clocks stopped. This is the default configuration after power-up.
LPS (Low Power Standby)
VREF maintained using 1MOhm string
9.720
PLL running with 13MHz input to MCLKB
Maximum Power - everything on
3.3 13.656 3.3 15.472 3.3
2.938 105.82
Table 1 Supply Current Consumption
Notes:
1.
Unless otherwise specified, all figures are at TA = +25C, audio sample rate fs = 48kHz, with zero signal (quiescent), and
voltage references settled.
2.
The power dissipated in the headphone, speaker and touchpanel is not included in the above table.
w
PP, Rev 3.3, November 2011
11
WM9713L
Pre-Production
SIGNAL TIMING REQUIREMENTS
AC97 INTERFACE TIMING
CLOCK SPECIFICATIONS
tCLK_HIGH
tCLK_LOW
BITCLK
tCLK_PERIOD
tSYNC_HIGH
tSYNC_LOW
SYNC
tSYNC_PERIOD
Figure 1 Clock Specifications (50pF External Load)
Test Conditions
DBVDD = 3.3V, DCVDD = 3.3V, DGND1 = DGND2 = 0V, TA = -25C to +85C, unless otherwise
stated.
PARAMETER
SYMBOL
MIN
BITCLK frequency
BITCLK period
TYP
MAX
12.288
MHz
81.4
tCLK_PERIOD
BITCLK output jitter
ns
750
ps
ns
BITCLK high pulse width (Note 1)
tCLK_HIGH
36
40.7
45
BITCLK low pulse width (Note 1)
tCLK_LOW
36
40.7
45
SYNC frequency
48
UNIT
ns
kHz
tSYNC_PERIOD
20.8
s
SYNC high pulse width
tSYNC_HIGH
1.3
s
SYNC low pulse width
tSYNC_LOW
19.5
s
SYNC period
Note:
1.
w
Worst case duty cycle restricted to 45/55
PP, Rev 3.3, November 2011
12
WM9713L
Pre-Production
DATA SETUP AND HOLD
Figure 2 Data Setup and Hold (50pF External Load)
Note:
Setup and hold times for SDATAIN are with respect to the AC’97 controller, not the
WM9713L.
Test Conditions
DBVDD = 3.3V, DCVDD = 3.3V, DGND1 = DGND2 = 0V, TA = -25C to +85C, unless otherwise
stated.
PARAMETER
SYMBOL
MIN
TYP
MAX
UNIT
Setup to falling edge of BITCLK
tSETUP
10
Hold from falling edge of BITCLK
tHOLD
10
Output valid delay from rising edge of
BITCLK
w
tCO
ns
ns
15
ns
PP, Rev 3.3, November 2011
13
WM9713L
Pre-Production
SIGNAL RISE AND FALL TIMES
triseCLK
tfallCLK
BITCLK
triseSYNC
tfallSYNC
SYNC
triseDIN
tfallDIN
triseDOUT
tfallDOUT
SDATAIN
SDATAOUT
Figure 3 Signal Rise and Fall Times (50pF External Load)
Test Conditions
DBVDD = 3.3V, DCVDD = 3.3V, DGND1 = DGND2 = 0V, TA = -25C to +85C, unless otherwise
stated.
PARAMETER
SYMBOL
MIN
TYP
MAX
UNIT
BITCLK rise time
triseCLK
2
6
ns
BITCLK fall time
tfallCLK
2
SYNC rise time
triseSYNC
SYNC fall time
tfallSYNC
SDATAIN rise time
triseDIN
2
6
ns
SDATAIN fall time
tfallDIN
2
6
ns
6
ns
6
ns
6
ns
SDATAOUT rise time
triseDOUT
6
ns
SDATAOUT fall time
tfallDOUT
6
ns
AC-LINK POWERDOWN
SLOT 1
SLOT 2
SYNC
BITCLK
SDATAOUT
WRITE
TO 0X20
DATA PR4
DON'T
CARE
tS2_PDOWN
SDATAIN
Figure 4 AC-Link Powerdown Timing
AC-Link powerdown occurs when PR4 (register 26h, bit 12) is set (see “Power Management” section).
PARAMETER
End of Slot 2 to BITCLK and SDATAIN
low
w
SYMBOL
tS2_PDOWN
MIN
TYP
MAX
UNIT
1.0
s
PP, Rev 3.3, November 2011
14
WM9713L
Pre-Production
COLD RESET (ASYNCHRONOUS, RESETS REGISTER SETTINGS)
Figure 5 Cold Reset Timing
Note:
For correct operation SDATAOUT and SYNC must be held LOW for entire RESETB active
low period otherwise the device may enter test mode. See AC'97 specification or Wolfson
applications note WAN104 for more details.
PARAMETER
RESETB active low pulse width
SYMBOL
MIN
tRST_LOW
1.0
TYP
MAX
UNIT
s
WARM RESET (ASYNCHRONOUS, PRESERVES REGISTER SETTINGS)
Figure 6 Warm Reset Timing
PARAMETER
SYNC active high pulse width
SYNC inactive to BITCLK startup
delay
w
SYMBOL
MIN
tRST2CLK
TYP
1.3
tSYNC_HIGH
162.4
MAX
UNIT
s
ns
PP, Rev 3.3, November 2011
15
WM9713L
Pre-Production
PCM AUDIO INTERFACE TIMING – SLAVE MODE
Figure 7 Digital Audio Data Timing – Slave Mode
Test Conditions
DBVDD = 3.3V, DCVDD = 3.3V, DGND1 = DGND2 = 0V, TA = -25C to +85C, unless otherwise stated.
PARAMETER
SYMBOL
MIN
TYP
MAX
UNIT
Audio Data Input Timing Information
PCMCLK cycle time
tPCMY
50
ns
PCMCLK pulse width high
tPCMH
20
ns
PCMCLK pulse width low
tPCML
20
ns
PCMFS set-up time to PCMCLK rising edge
tFSSU
10
ns
PCMFS hold time from PCMCLK rising edge
tFSH
10
ns
PCMDAC set-up time from PCMCLK rising edge
tDS
10
ns
PCMDAC hold time from PCMCLK rising edge
tDH
10
ns
PCMADC propagation delay from PCMCLK falling edge
tDD
10
ns
Note:
1.
PCMCLK period should always be greater than or equal to Voice CLK period.
w
PP, Rev 3.3, November 2011
16
WM9713L
Pre-Production
PCM AUDIO INTERFACE TIMING – MASTER MODE
Figure 8 Digital Audio Data Timing – Master Mode (see Control Interface)
Test Conditions
DBVDD = 3.3V, DCVDD = 3.3V, DGND1 = DGND2 = 0V, TA = -25C to +85C, unless otherwise stated.
PARAMETER
SYMBOL
MIN
TYP
MAX
UNIT
Audio Data Input Timing Information
PCMFS propagation delay from PCMCLK falling edge
tDL
10
ns
PCMADC propagation delay from PCMCLK falling edge
tDDA
10
ns
PCMDAC setup time to PCMCLK rising edge
tDST
10
ns
PCMDAC hold time from PCMCLK rising edge
tDHT
10
ns
w
PP, Rev 3.3, November 2011
17
WM9713L
Pre-Production
DEVICE DESCRIPTION
INTRODUCTION
The WM9713L is a largely pin compatible upgrade to WM9712, with a PCM voice CODEC added.
This CODEC is interfaced via a PCM type audio interface which makes use of GPIO pins for
connection.
It is designed to meet the mixed-signal requirements of portable and wireless smartphone systems. It
includes audio recording and playback, touchpanel digitisation, battery monitoring, auxiliary ADC and
GPIO functions, all controlled through a single 5-wire AC-Link interface. Additionally, PCM voice
CODEC functions are supported through provision of an additional voice DAC and a PCM audio serial
interface.
A PLL is included to allow unrelated reference clocks to be used for generation of the AC link system
clock. Typically 13MHz or 2.048MHz clock sources might be used as a reference.
SOFTWARE SUPPORT
The basic audio features of the WM9713L are software compatible with standard AC’97 device
drivers. However, to better support the touchpanel and other additional functions, Wolfson
Microelectronics supplies custom device drivers for selected CPUs and operating systems. Please
contact your local Wolfson Sales Office for more information.
AC’97 COMPATIBILITY
The WM9713L uses an AC’97 interface to communicate with a microprocessor or controller. The
audio and GPIO functions are largely compliant with AC’97 Revision 2.2. The following differences
from the AC’97 standard are noted:
Pinout: The function of some pins has been changed to support device specific
features. The PHONE and PCBEEP pins have been moved to different locations on
the device package.
Package: The default package for the WM9713L is a 77mm leadless QFN
package.
Audio mixing: The WM9713L handles all the audio functions of a smartphone,
including audio playback, voice recording, phone calls, phone call recording, ring
tones, as well as simultaneous use of these features. The AC’97 mixer architecture
does not fully support this. The WM9713L therefore uses a modified AC’97 mixer
architecture with three separate mixers.
Tone Control, Bass Boost and 3D Enhancement: These functions are implemented
in the digital domain and therefore affect only signals being played through the
audio DACs, not all output signals as stipulated in AC’97.
Some other functions are additional to AC’97:
w
On-chip BTL loudspeaker driver for mono or stereo speakers
On-chip BTL driver for ear speaker (phone receiver)
Auxiliary mono DAC for ring tones, system alerts etc.
Touchpanel controller
Auxiliary ADC Inputs
2 Analogue Comparators for Battery Alarm
Programmable Filter Characteristics for Tone Control and 3D Enhancement
PCM interface to additional Voice DAC and existing audio ADCs
PLL to create AC’97 system clock from unrelated reference clock input
PP, Rev 3.3, November 2011
18
WM9713L
Pre-Production
PCM CODEC
The PCM voice CODEC functions typically required by mobile telephony devices are provided by an
extra voice DAC on the WM9713L, which is interfaced via a standard PCM type data interface, which
is constructed through optional use of 4 of the GPIO pins on WM9713L. The audio output data from
one or both of the audio ADCs can also be output over this PCM interface, allowing a full voice
CODEC function to be implemented. This PCM interface supports sample rates from 8 to 48ks/s
using the standard AC’97 master clock.
w
PP, Rev 3.3, November 2011
19
WM9713L
Pre-Production
AUDIO PATHS OVERVIEW
WM9713 Analogue
Tone and 3D
1Eh / 20h /
40h:13 (3DE)
ADC Left
18 Bit DACL
slot 3
INV2
INV1
SPKMIX
MONOMIX
HPMIXR
HPMIXL
VXDAC
AUXDAC
RECMUXR
RECMUXL
MIC2
MICA
PCBEEP
MONOIN
LINER
LINEL
DACL
0Ch:12-8
00000 = +12dB
11111 = -34.5dB
40h:7
(Loopback)
AC'97 Link
DACR
Note: all PGAs and summers are inverting
DACL
0C
1Eh:15-13
LINEL
MICB
08h:12-8
00000 = +12dB
11111 = -34.5dB
RECMUXL
MONOIN
RECMUXR
AUXDAC
VXDAC
16
6dB -> -15dB
6dB -> -15dB
6dB -> -15dB
6dB -> -15dB
6dB -> -15dB
Headphone
Mixer L
04h:12-8
00000 = 0dB
11111 = -46.5dB
10h:4-0
HPMIXL
1
15-1
14h:
1
5-1
h:1
2
14
5-1
h:1 2
1A 5-1
h:1
18
HPL
Vmid
Zero-cross
detect
04h:14 (ZC)
04h:15 (MUTE)
6dB -> -15dB
16 Bit PCM
VXDAC
02h:12-8
00000 = 0dB
11111 = -46.5dB
SPKMIX
VXDAC
AUXDAC
RECMUXR
RECMUXL
MICB
MICA
PCBEEP
MONOIN
LINER
LINEL
DACR
HPMIXL
DACL
PCM Link
6dB -> -15dB
1Ch:7-6
LINEL
MICA
1Ch:13-11
PCBEEP
MONOIN
MICB
MICA
LINER
LINEL
PCBEEP
0A
h:1
08
5
h:1
5
h:1
5-1
2
10h:
4-0
5
h:1
MONOIN
0Ah:12-8
00000 = +12dB
11111 = -34.5dB
INV1
DACL
SPKL
DACR
0C
1Ch:15-14
INV1
MONO
Zero-cross
detect
Vmid
6dB -> -15dB
08h:6 (ZC)
08h:7 (MUTE)
INV2
INV1
SPKMIX
HPMIXL
6dB -> -15dB
VXDAC
AUXDAC
RECMUXR
RECMUXL
MICB
MICA
PCBEEP
MONOIN
LINER
LINEL
DACR
DACL
PCBEEP
MONOIN
MICB
MICA
LINER
LINEL
VXDAC
0dB / 20dB
08h:4-0
00000 = 0dB
11111 = -46.5dB
MONOMIX
+5
10h:6
0-8
h:1
14
0-8
h:1
14 :7-4
h
A
1
MONOMIX
AUXDAC
0dB / 20dB
10h:7+5
HPMIXR
RECMUXR
0dB / 20dB
h:7
RECMUXL
0Eh:12-8
00000 = +12dB
11111 = -34.5dB
0dB / 20dB
02h:14 (ZC)
02h:15 (MUTE)
MONO
Mixer
18
PCBEEP
MICB
6dB -> -15dB
-4
LINER
MICA
0C
h:1
0A
3
h:1
3
0A
h:1
3
16h7
:4
3
h:1
LINEL
PCBEEP
Zero-cross
detect
Vmid
06h:4-0
00000 = 0dB
11111 = -46.5dB
12h:14 (GRL=0)
12h:11:8
0000 = 0db
1111 = +22.5dB
12h:14 (GRL=1)
12h:13-8
11111 = +30dB
00000 = -17.25dB
OUT3
1Ch:3-2
Vmid
Zero-cross
detect
06h:6 (ZC)
06h:7 (MUTE)
14h:6
0 = 0dB
1 = 20dB
18 Bit ADC
Variable Slot
5C:1-0 (ASS)
5C:3 (HPF)
5C:4 (ADCO)
Sent to Both
06h:12-8
00000 = 0dB
11111 = -46.5dB
PCM Link
AC'97 Link
INV2
OUT4
1Ch:1-0
14h:5-3
INV1
ALC:5Ch/60h/62h
Vmid
Zero-cross
detect
ADC Right
18 Bit DACR
slot 3
INV2
INV1
SPKMIX
MONOMIX
HPMIXR
HPMIXL
VXDAC
AUXDAC
RECMUXR
RECMUXL
MICB
MICA
PCBEEP
MONOIN
LINER
LINEL
DACR
Tone and 3D
1Eh / 20h /
40h:13 (3DE)
AC'97 Link
DACL
PCBEEP
MONOIN
MICB
MICA
LINER
LINEL
06h:14 (ZC)
06h:15 (MUTE)
0Ch:4-0
00000 = +12dB
11111 = -34.5dB
40h:7
(Loopback)
DACR
LINER
0C
5
MICA
MICB
RECMUXL
RECMUXR
AUXDAC
VXDAC
Vmid
6dB -> -15dB
6dB -> -15dB
6dB -> -15dB
DACR
6dB -> -15dB
6dB -> -15dB
INV2
INV1
VXDAC
AUXDAC
RECMUXR
RECMUXL
MICB
MICA
PCBEEP
MONOIN
LINER
LINEL
1Ch:10-8
11-8
16h:
1-8
h:1
1A
1-8
h:1
18
6dB -> -15dB
1Eh:12-10
18 Bit ADC
Variable Slot
5C:1-0 (ASS)
5C:3 (HPF)
5C:4 (ADCO)
DACR
DACL
14h:6
0 = 0dB
1 = 20dB
SPKR
Zero-cross
detect
02h:6 (ZC)
02h:7 (MUTE)
HPMIXL
14h:2-0
PCBEEP
MONOIN
MICB
VXDAC
Vmid
SPKMIX
MICCM
12h:6 (GRR=0)
12h:3:0
0000 = 0db
1111 = +22.5dB
12h:6 (GRR=1)
12h:5-0
11111 = +30dB
00000 = -17.25dB
02h:4-0
00000 = 0dB
11111 = -46.5dB
Speaker
Mixer
MONOMIX
AUXDAC
MICA
04h:6 (ZC)
04h:7 (MUTE)
HPMIXR
PCBEEP
HPR
Zero-cross
detect
08h:14
MONOIN
0Eh:4-0
00000 = +12dB
11111 = -34.5dB
LINER
Vmid
INV2
0A
h:1
0A 4
h1
4
0C
h:1
4
0Ch:
14
Vmid
LINEL
HPMIXR
LINEL
DACL
22h:9-8
00 = +12dB
11 = +30dB
04h:4-0
00000 = 0dB
11111 = -46.5dB
10h:4-0
1
15-1
14h:
1
5-1
h:1
2
14
-1
:15 2
h
1A 5-1
h:1
18
6dB -> -15dB
LINER
MIC2A
MIC2B
Headphone
Mixer R
SPKMIX
VXDAC
AUXDAC
RECMUXR
RECMUXL
MICB
MICA
PCBEEP
MONOIN
LINER
22h:11-10
00 = +12dB
11 = +30dB
LINEL
22h:
13-12
6dB -> -15dB
HPMIXR
DACL
Vmid
16
6dB -> -15dB
12 Bit Resistor
string DAC
2Eh/64h
DACR
AC'97 Link
6dB -> -15dB
1Ch:5-4
PCBEEP
LINER
MIC1
0A
h:1
5
08
h:1
5
h:1
5-1
2
10h:4
-0
h:1
MONOIN
0Ah:4-0
00000 = +12dB
11111 = -34.5dB
Sent to Both
PCM Link
AC'97 Link
INV2
INV1
HPMIXL
SPKMIX
HPMIXR
MONOMIX
PCBEEP
MONOIN
MICB
MICA
LINEL
LINER
ALC:5Ch/60h/62h
PR Bit Code
PR0 - Audio ADCs & record mux
PR1 - Stereo DAC
PR2 - Input PGAs & mixers
PR3 - Refs, input PGAs, mixers & output PGAs
PR6 - Output PGAs
Note: PR bits are active low - i.e. 0 = "ON"; 1 = "OFF"
=> Enable when { (PR0 || PR2) && PR3 } are low
VMICBIAS
AVDD
AGND
CAP
VREF
Figure 9 Audio Paths Overview
w
PP, Rev 3.3, November 2011
20
WM9713L
Pre-Production
CLOCK GENERATION
WM9713L supports clocking from 2 separate sources, which can be selected via the AC’97 interface:
External clock input MCLKA
External clock input MCLKB
The source clock is divided to appropriate frequencies in order to run the AC’97 interface, PCM
interface, voice DAC and hi-fi DSP by means of a programmable divider block. Clock rates may be
changed during operation via the AC’97 link in order to support alternative modes, for example low
power mode when voice data is being transmitted only. A PLL is present to add flexibility in selection
of input clock frequencies, typical choices being 2.048MHz, 4.096MHz or 13MHz.
INITIALISING THE AC’97 LINK
By default, the AC’97 link is disabled and therefore will not be running after power on or a COLD reset
event. Before any register map configuration can begin, it is necessary to start the AC’97 link. This is
achieved by sending a WARM reset to the CODEC as defined in Figure 6.
Default mode on power-up also assumes a clock will be present on MCLKA with the PLL powered
down. After a WARM reset the CODEC will start the AC’97 link using MCLKA as a reference. This
enables data to be clocked via the AC’97 link to define the desired clock divider mode and whether
PLL needs to be activated.
Note: MCLKA can be any available frequency.
When muxing between MCLKA and MCLKB both clocks must be active for at least two clock cycles
after the switching event.
CLOCK DIVISION MODES
Figure 10 shows the clocking strategy for WM9713L. Clocking is controlled by CLK_MUX, CLK_SRC
and S[6:0].
CLKAX2, CLKBX2 – clock doublers on inputs MCLKA and MCLKB.
CLK_MUX - selects between MCLKA and MCLKB.
CLK_SRC – selects between external or PLL derived clock reference.
S[3:0] – sets the voice DAC clock rate and PCM interface clock when in master mode
(division ratio 1 to 16 available).
S[6:4] - sets the hi-fi clocking rate (division ratio 1 to 8 available).
The registers used to set these switches can be accessed from register address 44h (see Table 3).
If a mode change requires switching from an external clock to a PLL generated clock then it is
recommended to set the clock division ratios required for the PLL clock scheme prior to switching
between clocks. This option is accommodated by means of two sets of registers. SPLL[6:0] is used to
set the divide ratio of the clock when in PLL mode and SEXT[6:0] is used to divide the clock when it is
derived from an external source. If the PLL is selected (CLK_SRC = 0), S[6:0] = SPLL[6:0]. SPLL[6:0] is
defined in register 46h (see Table 4) and is written to using the page address mode. More details on
page address mode for controlling the PLL are found on page 20. Register 46h also contains a
number of separate control bits relating to the PLL’s function. If an external clock is selected
(CLK_SRC = 1) S[6:0] = SEXT[6:0]. SEXT[6:0] is defined in register address 44h. Writing to registers
44h and 46h enables pre-programming of the required clock mode before the PLL output is selected.
w
PP, Rev 3.3, November 2011
21
WM9713L
Pre-Production
Figure 10 Clocking Architecture for WM9713L
INTERNAL CLOCK FREQUENCIES
The internal clock frequencies are defined as follows (refer to Figure 10):
AC97 CLK – nominally 24.576MHz, used to generate AC97 BITCLK at 12.288MHz
HIFI CLK – for hi-fi playback at 48ks/s HIFI CLK = 24.576MHz. See Table 2 for voice only
playback.
Voice DAC CLK – see Table 2 for sample rate vs clock frequency.
SAMPLE RATE
VOICE DAC CLK
FREQUENCY
HIFI CLK
FREQUENCY
8ks/s voice and hi-fi
2.048MHz
24.576MHz
8ks/s voice only (power save)
2.048MHz
4.096MHz
16ks/s voice and hi-fi
4.096MHz
24.576MHz
16ks/s voice only (power save)
4.096MHz
8.192MHz
32ks/s voice and hi-fi
8.192MHz
24.576MHz
48ks/s voice and hi-fi
12.288MHz
24.576MHz
Table 2 Clock Division Mode Table
AUXADC
The clock for the AUXADC nominally runs at 768kHz and is derived from BITCLK. The divisor for the
clock generator is set by PENDIV. This enables the AUXADC clock frequency to be set according to
power consumption and conversion rate considerations.
w
PP, Rev 3.3, November 2011
22
WM9713L
Pre-Production
Clock mode and division ratios are controlled by register 44h as shown in Table 3.
REGISTER
ADDRESS
44h
BIT
LABEL
14:12
SEXT[6:4]
DEFAULT
000 (div 1)
DESCRIPTION
Hi-fi Block Clock Division Control
000 = f
001 = f/2
…
111 = f/8
11:8
SEXT[3:0]
0000 (div 1)
Voice DAC Clock Division Control
0000 = f
0001 = f/2
…
1111 = f/16
7
CLKSRC
1 (ext clk)
AC97 CLK Source Control
1 = External clock
0 = PLL clock
5:3
PENDIV
000 (div 16)
AUXADC Clock Division Control
000 = f/16
001 = f/12
010 = f/8
011 = f/6
100 = f/4
101 = f/3
110 = f/2
111 = f
2
CLKBX2
0 (Off)
MCLKB Multiplier Control
0 = Normal
1 = Multiply by 2
1
CLKAX2
0 (Off)
MCLKA Multiplier Control
0 = Normal
1 = Multiply by 2
0
CLKMUX
0 (MCLKA)
External Clock Source Control
0 = Use MCLKA
1 = Use MCLKB
Note: On power-up clock must be present
on MCLKA and must be active for 2 clock
cycles after switching to MCLKB
Table 3 Clock Muxing and Division Control
w
PP, Rev 3.3, November 2011
23
WM9713L
Pre-Production
PLL MODE
The PLL operation is controlled by register 46h (see Table 4) and has two modes of operation:
Integer N
Fractional N
The PLL has been optimized for nominal input clock (PLL_IN) frequencies in the range 8.192MHz –
19.661MHz (LF=0) and 2.048MHz – 4.9152MHz (LF=1). Through use of a clock divider (div by 2 / 4)
on the input to the PLL frequencies up to 78.6MHz can be accommodated. The input clock divider is
enabled by DIVSEL (0=Off) and the division ratio is set by DIVCTL (0=div2, 1=div4).
Figure 11 PLL Architecture
REGISTER
ADDRESS
46h
BIT
15:12
LABEL
N[3:0]
DEFAULT
0000
DESCRIPTION
PLL N Divide Control
0000 = Divide by 1
0001 = Divide by 1
0010 = Divide by 2
…
1111 = Divide by 15
Note: must be set between 05h and 0Ch for
integer N mode
11
LF
0 = off
PLL Low Frequency Input Control
1 = Low frequency mode (input clock <
8.192MHz)
0 = Normal mode
10
SDM
0 = off
PLL SDM Enable Control
1 = Enable SDM (required for fractional N
mode)
0 = Disable SDM
9
DIVSEL
0 = off
PLL Input Clock Division Control
0 = Divide by 1
1 = Divide according to DIVCTL
8
DIVCTL
0
PLL Input Clock Division Value Control
0 = Divide by 2
1 = Divide by 4
6:4
PGADDR
000
Pager Address
Pager address bits to access programming
of K[21:0] and SPLL[6:0]
3:0
PGDATA
0000
Pager Data
Pager data bits
Table 4 PLL Clock Control
w
PP, Rev 3.3, November 2011
24
WM9713L
Pre-Production
INTEGER N MODE
The nominal output frequency of the PLL (PLL_OUT) is 98.304MHz which is divided by 4 to achieve a
nominal system clock of 24.576MHz.
The integer division ratio (N) is determined by: FPLL_out / FPLL_IN , and is set by N[3:0] and must be in the
range 5 to 12 for integer N operation (0101 = div by 5, 1100 = div by 12). Note that setting LF=1
enables a further division by 4 required for input frequencies in the range 2.048MHz – 4.096MHz.
Integer N mode is selected by setting SDM=0.
FRACTIONAL N MODE
Fractional N mode provides a divide resolution of 1/2
22
and is set by K[21:0] (register 46h, see
section). The relationship between the required division X, the fractional division K[21:0] and the
integer division N[3:0] is:
K 2 22 X N
where 0 < (X – N) < 1 and K is rounded to the nearest whole number.
For example, if the PLL_IN clock is 13MHz and the desired PLL_OUT clock is 98.304MHz then the
desired division, X, is 7.5618. So N[3:0] will be 7h and K[21:0] will be 23F488h to produce the desired
98.304MHz clock (see Table 5).
INPUT CLOCK (PLL_IN)
DESIRED
PLL
OUTPUT
(PLL_OUT)
DIVISION
REQUIRED
(X)
FRACTIONAL
DIVISION (K)
INTEGER
DIVISION (N)
0
12x4*
2.048MHz
98.304MHz
48
4.096MHz
98.304MHz
24
0
6x4*
98.304MHz
8
0
8
13MHz
98.304MHz
7.5618
0.5618
7
27MHz (13.5MHz)**
98.304MHz
7.2818
0.2818
7
12.288MHz
*Divide by 4 enabled in PLL feedback path for low frequency inputs. (LF = 1)
**Divide by 2 enabled at PLL input for frequencies > 14.4MHz > 38MHz (DIVSEL = 1, DIVCTL = 0)
Table 5 PLL Modes of Operation
w
PP, Rev 3.3, November 2011
25
WM9713L
Pre-Production
PLL REGISTER PAGE ADDRESS MAPPING
The clock division control bits SPLL[6:0] and the PLL fractional N division bits are accessed through
register 46h using a sub-page address system. The 3 bit pager address allows 8 blocks of 4 bit data
words to be accessed whilst the register address is set to 46h. This means that when register address
46h is selected a further 7 cycles of programming are required to set all of the page data bits. Control
bit allocation for these page addresses is described in Table 6.
PAGE
ADDRESS
BIT
LABEL
DEFAULT
DESCRIPTION
111
31:28
SPLL[6:4]
0h
110
27:24
SPLL[3:0]
0h
101
23:22
Reserved
0h
Reserved bits
21:20
K[21:0]
0h
Sigma Delta Modulator control word for
fractional N division. Division resolution is
2
1/22
100
19:16
0h
011
15:12
0h
010
11:8
0h
001
7:4
0h
000
3:0
0h
Clock division control bus SPLL[6:0]. Clock
divider reads this control word if PLL is
enabled. Bits [6:4] and [3:0] have the same
functionality as 44h [14:12] and [11:8]
respectively
Table 6 Pager Control Bit Allocation
Powerdown for the PLL and internal clocks is via registers 26h and 3Ch (see Table 7).
REGISTER
ADDRESS
26h
BIT
13
LABEL
PR5
DEFAULT
1 (Off)
DESCRIPTION
Internal Clock Disable Control
1 = Disabled
0 = Enabled
3Ch
9
PLL
1 (Off)
PLL Disable Control
1 = Disabled
0 = Enabled
N.B. both PR5 and PLL must be asserted low before PLL is enabled
Table 7 PLL Powerdown Control
w
PP, Rev 3.3, November 2011
26
WM9713L
Pre-Production
DIGITAL INTERFACES
The WM9713L has two interfaces, a data and control AC’97 interface and a data only PCM interface.
The AC’97 interface is available through dedicated pins (SDATAOUT, SDATAIN, SYNC, BITCLK and
RESETB) and is the sole control interface with access to all data streams on the device except for the
Voice DAC. The PCM interface is available through the GPIO pins (PCMCLK, PCMFS, PCMDAC and
PCMADC) and provides access to the Voice DAC. It can also transmit the data from the Stereo ADC.
This can be useful, for example, to allow both sides of a phone conversation to be recorded by mixing
the transmit and receive paths on one of the ADC channels and transmitting it over the PCM
interface.
AC97 INTERFACE
INTERFACE PROTOCOL
The WM9713L uses an AC’97 interface for both data transfer and control. The AC-Link has 5 wires:
SDATAIN (pin 8) carries data from the WM9713L to the controller
SDATAOUT (pin 5) carries data from the controller to the WM9713L
BITCLK (pin 6) is a clock, derived from either MCLKA or MCLKB inputs and
supplied to the controller.
SYNC is a synchronization signal generated by the controller and passed to the
WM9713L
RESETB resets the WM9713L to its default state
Figure 12 AC-Link Interface (typical case with BITCLK generated by the AC97 CODEC)
The SDATAIN and SDATAOUT signals each carry 13 time-division multiplexed data streams (slots 0
to 12). A complete sequence of slots 0 to 12 is referred to as an AC-Link frame, and contains a total
of 256 bits. The frame rate is 48kHz. This makes it possible to simultaneously transmit and receive
multiple data streams (e.g. audio, touchpanel, AUXDAC, control) at sample rates up to 48kHz.
Detailed information can be found in the AC’97 (Revision 2.2) specification, which can be obtained at
www.intel.com/design/chipsets/audio/
Note:
SDATAOUT and SYNC must be held low when RESETB is applied. These signals must be held low
for the entire duration of the RESETB pulse and especially during the low-to-high transition of
RESETB. If SDATAOUT or SYNC is high during reset, the WM9713L may enter test modes.
Information relating to this operation is available in the AC'97 specification or in Wolfson applications
note WAN-0104 available at www.wolfsonmirco.com.
w
PP, Rev 3.3, November 2011
27
WM9713L
Pre-Production
PCM INTERFACE
OPERATION
WM9713L can implement a PCM voice CODEC function using the dedicated VXDAC and either one
or both of the existing hi-fi ADC’s. In PCM CODEC mode, VXDAC input and ADC output are
interfaced via a PCM style port via GPIO pins.
This interface can support one ADC channel, or stereo/dual ADC channels if required, (two channels
of data are sent per PCM frame as back to back words).
In voice only mode, the AC link is used only for control information, not audio data. Therefore it will
generally be shut down (PR4=1), except when control data must be sent.
The PCM interface makes use of 4 of the GPIO interface pins, for clock, frame, and data in/out. If the
PCM CODEC function is not enabled then the GPIO pins may be used for other functions.
INTERFACE PROTOCOL
The WM9713L PCM audio interface is used for the input of data to the Voice DAC and the output of
data from the Stereo ADC. When enabled, the PCM audio interface uses four GPIO pins:
GPIO1/PCMCLK: Bit clock
GPIO3/PCMFS: Frame Sync
GPIO4/PCMDAC: Voice DAC data input
GPIO5/PCMADC: Stereo ADC data output
Depending on the mode of operation (see “PCM Interface Modes”), at least one of these four pins
must be set up as an output by writing to register 4Ch (see Table 62). When not enabled the GPIOs
may be used for other functions on the WM9713L.
PCM INTERFACE MODES
The WM9713L PCM audio interface may be configured in one of four modes:
Disabled Mode: The WM9713L disables and tri-states all PCM interface pins. Any
clock input is ignored and ADC/DAC data is not transferred.
Slave Mode: The WM9713L accepts PCMCLK and PCMFS as inputs from an
external source.
Master Mode: The WM9713L generates PCMCLK and PCMFS as outputs.
Partial Master Mode: The WM9713L generates PCMCLK as an output, and accepts
PCMFS as an external input.
PCM AUDIO DATA FORMATS
Four different audio data formats are supported:
DSP mode
Left justified
Right justified
2
IS
All four of these modes are MSB first. They are described below. Refer to the Electrical
Characteristics section for timing information.
Note:
PCMCLK and PCMFS must be synchronized with the BITCLK from the AC’97 interface.
w
PP, Rev 3.3, November 2011
28
WM9713L
Pre-Production
The PCM Interface may be configured for Mono mode, where only one channel of ADC data is output.
In this mode the interface should be configured for DSP mode. A short or long frame sync is
supported and the MSB is available on either the 1st (mode B) or 2nd (mode A) rising edge of
VXCLK.
Note that when operating in stereo mode the mono Voice DAC always uses the left channel data as
its input.
1/fs
1 PCMCLK
PCMFS
PCMCLK
PCMADC/
PCMDAC
1
2
3
n-2 n-1
MSB
n
LSB
Input Word Length (WL)
Figure 13 PCM Interface Mono Mode (mode A, FSP=0)
1/fs
1 PCMCLK
PCMFS
PCMCLK
PCMADC/
PCMDAC
1
2
3
n-2 n-1
MSB
n
LSB
Input Word Length (WL)
Figure 14 PCM Interface Mono Mode (mode B, FSP=1)
w
PP, Rev 3.3, November 2011
29
WM9713L
Pre-Production
In DSP mode, the left channel MSB is available on either the 1st (mode B) or 2nd (mode A) rising
edge of PCMCLK (selectable by FSP) following a rising edge of PCMFS. Right channel data
immediately follows left channel data. Depending on word length, PCMCLK frequency and sample
rate, there may be unused PCMCLK cycles between the LSB of the right channel data and the next
sample.
1/fs
1 BCLK / VXCLK
PCMFS
PCMCLK
RIGHT CHANNEL
LEFT CHANNEL
PCMADC/
PCMDAC
1
2
3
n-2 n-1
MSB
n
1
2
3
n-2 n-1
n
LSB
Input Word Length (WL)
Figure 7 DSP Mode Audio Interface (mode A, FSP=0)
1/fs
1 BCLK / VXCLK
PCMFS
PCMCLK
RIGHT CHANNEL
LEFT CHANNEL
PCMADC/
PCMDAC
1
2
3
n-2 n-1
MSB
n
1
2
3
n-2 n-1
n
LSB
Input Word Length (WL)
Figure 15 DSP Mode Audio Interface (mode B, FSP=1)
w
PP, Rev 3.3, November 2011
30
WM9713L
Pre-Production
In Left Justified mode, the MSB is available on the first rising edge of PCMCLK following a PCMFS
transition. The other bits up to the LSB are then transmitted in order. Depending on word length,
PCMCLK frequency and sample rate, there may be unused PCMCLK cycles before each PCMFS
transition.
1/fs
LEFT CHANNEL
RIGHT CHANNEL
PCMFS
PCMCLK
PCMADC/
PCMDAC
1
2
3
n-2 n-1
MSB
n
1
LSB
2
3
n-2 n-1
MSB
n
LSB
Figure 16 Left Justified Audio Interface (assuming n-bit word length)
In Right Justified mode, the LSB is available on the last rising edge of PCMCLK before a PCMFS
transition. All other bits are transmitted before (MSB first). Depending on word length, PCMCLK
frequency and sample rate, there may be unused PCMCLK cycles after each PCMFS transition.
1/fs
LEFT CHANNEL
RIGHT CHANNEL
PCMFS
PCMCLK
PCMADC /
PCMDAC
1
2
3
n-2 n-1
MSB
n
1
2
3
n-2 n-1
n
LSB
MSB
LSB
Figure 17 Right Justified Audio Interface (assuming n-bit word length)
2
In I S mode, the MSB is available on the second rising edge of PCMCLK following a PCMFS
transition. The other bits up to the LSB are then transmitted in order. Depending on word length,
PCMCLK frequency and sample rate, there may be unused PCMCLK cycles between the LSB of one
sample and the MSB of the next.
1/fs
LEFT CHANNEL
RIGHT CHANNEL
PCMFS
PCMCLK
1 BCLK
1 BCLK
PCMADC/
PCMDAC
1
MSB
2
3
n-2 n-1
n
LSB
1
2
3
MSB
n-2 n-1
n
LSB
2
Figure 18 I S Justified Audio Interface (assuming n-bit word length)
w
PP, Rev 3.3, November 2011
31
WM9713L
Pre-Production
CONTROL
The register bits controlling PCM audio format, word length and operating modes are summarised
below. CTRL must be set to override the normal use of the PCM interface pins as GPIOs, MODE
must be set to specify master/slave modes.
REGISTER
ADDRESS
36h
BIT
15
LABEL
CTRL
DEFAULT
0
PCM
Control
DESCRIPTION
GPIO Pin Configuration Control
0 = GPIO pins as GPIOs
1 = GPIO pins configured as PCM interface
and controlled by this register
14:13
MODE
10
PCM Interface Mode Control
00 = PCM interface disabled [PCMCLK tristated, PCMFS tri-stated]
01 = PCM interface in slave mode [PCMCLK
as input, PCMFS as input]
10 = PCM interface in master mode [PCMCLK
as output, PCMFS as output]
11 = PCM interface in partial master mode
[PCMCLK as output, PCMFS as input]
11:9
DIV
010
PCMCLK Rate Control
000 = Voice DAC clock
001 = Voice DAC clock / 2
010 = Voice DAC clock / 4
011 = Voice DAC clock / 8
100 = Voice DAC clock / 16
All other values are reserved
8
VDACOSR
1
Voice DAC Oversampling Rate Control
0: 128 x fs
1: 64 x fs
7
CP
0
PCMCLK Polarity Control
0 = Normal
1 = Inverted
6
5:4
FSP
SEL
0
10
FMT = 00, 01 or 10
FMT = 11
PCMFS Polarity
Control
DSP Mode Control
0 = Normal
0 = DSP Mode A
1 = Inverted
1 = DSP Mode B
PCM ADC Output Channel Control
00 = Normal stereo
01 = Reverse stereo
10 = Output left ADC data only
11 = Output right ADC data only
3:2
WL
00
PCM Data Word Length Control
00 = 16-bit
01 = 20-bit
10 = 24-bit
11 = 32-bit (not supported when FMT=00)
1:0
FMT
11
PCM Data Format Control
00 = Right justified
01 = Left justified
2
10 = I S
11 = DSP mode
Table 8 PCM CODEC Control
Note: Right justified does not support 32-bit data.
w
PP, Rev 3.3, November 2011
32
WM9713L
Pre-Production
AUDIO ADCS
STEREO ADC
The WM9713L has a stereo sigma-delta ADC to digitize audio signals. The ADC achieves high quality
audio recording at low power consumption. The ADC sample rate can be controlled by writing to a
control register (see “Variable Rate Audio”). It is independent of the DAC sample rate.
To save power, the left and right ADCs can be separately switched off using the Powerdown bits
ADCL and ADCR (register 3Ch, bits 5:4), whereas PR0 disables both ADCs (see “Power
Management” section). If only one ADC is running, the same ADC data appears on both the left and
right AC-Link slots.
The output from the ADC can be sent over either the AC link as usual, or output via the PCM interface
which may be configured on the GPIO pins.
HIGH PASS FILTER
The WM9713L audio ADC incorporates a digital high pass filter that eliminates any DC bias from the
ADC output data. The filter is enabled by default. For DC measurements, it can be disabled by writing
a ‘1’ to the HPF bit (register 5Ch, bit 3).
This high pass filter corner frequency can be selected to have different values in WM9713L, to suit
applications such as voice where a higher cutoff frequency is required.
REGISTER
ADDRESS
5Ch
BIT
3
LABEL
HPF
DEFAULT
0
DESCRIPTION
ADC HPF Disable Control
0 = HPF enabled (for audio)
1 = HPF disabled (for DC measurements)
5Ah
5:4
HPMODE
00
HPF Cut-Off Control
00 = 7Hz @ fs=48kHz
01 = 82Hz @ fs=16kHz
10 = 82Hz @ fs=8kHz
11 = 170Hz @ fs=8kHz
Note: the filter corner frequency is proportional to the sample rate.
Table 9 Controlling the ADC Highpass Filter
ADC SLOT MAPPING
By default, the output of the left audio ADC appears on slot 3 of the SDATAIN signal (pin 8), and the
right ADC data appears on slot 4. However, the ADC output data can also be sent to other slots, by
setting the ASS (ADC slot select) control bits as shown below.
REGISTER
ADDRESS
5Ch
BIT
1:0
LABEL
DEFAULT
ASS
00
Additional
Functions
(2)
DESCRIPTION
ADC Data Slot Mapping Control
Left Data
Right Data
00 =
Slot 3
Slot 4
01 =
Slot 7
Slot 8
10 =
Slot 6
Slot 9
11 =
Slot 10
Slot 11
Table 10 ADC Slot Mapping
w
PP, Rev 3.3, November 2011
33
WM9713L
Pre-Production
RECORD SELECTOR
The record selector determines which input signals are routed into the audio ADC. The left and right
channels can be selected independently. This is useful for recording a phone call: one channel can be
used for the RX signal and the other for the TX signal, so that both sides of the conversation are
digitized.
REGISTER
ADDRESS
14h
BIT
6
LABEL
RECBST
DEFAULT
0
Record
Routing /
Mux Select
DESCRIPTION
ADC Record Boost Control
1 = +20dB
0 = 0dB
Note: RECBST gain is in addition to the
microphone pre-amps (MPABST and
MPBBST bits) and record gain (GRL and
GRR / GRL bits).
5:3
RECSL
000
Left Record Mux Source Control
000 = MICA (pre-PGA)
001 = MICB (pre-PGA)
010 = LINEL (pre-PGA)
011 = MONOIN (pre-PGA)
100 = HPMIXL
101 = SPKMIC
110 = MONOMIX
111 = Reserved
2:0
RECSR
000
Right Record Mux Source Control
000 = MICA (pre-PGA)
001 = MICB (pre-PGA)
010 = LINEL (pre-PGA)
011 = MONOIN (pre-PGA)
100 = HPMIXL
101 = SPKMIC
110 = MONOMIX
111 = Reserved
Table 11 Audio Record Selector
w
PP, Rev 3.3, November 2011
34
WM9713L
Pre-Production
RECORD GAIN
The amplitude of the signal that enters the audio ADC is controlled by the Record PGA
(Programmable Gain Amplifier). The PGA gain can be programmed either by writing to the Record
Gain register, or by the Automatic Level Control (ALC) circuit (see next section). When the ALC is
enabled, any writes to the Record Gain register have no effect.
Two different gain ranges can be implemented: the standard gain range defined in the AC’97
standard, or an extended gain range with smaller gain steps. The ALC circuit always uses the
extended gain range, as this has been found to result in better sound quality.
REGISTER
ADDRESS
12h
BIT
15
LABEL
RMU
DEFAULT
1
Record Gain
DESCRIPTION
Audio ADC Input Mute Control
1 = Mute
0 = No mute
Note: This control applies to both channels
14
GRL
0
Left ADC PGA Gain Range Control
1 = Extended
0 = Standard
13:8
7
RECVOLL
ZC
000000
0
Left ADC Recording Volume Control
Standard (GRL=0)
Extended (GRL=1)
XX0000: 0dB
000000: -17.25dB
XX0001: +1.5dB
000001: -16.5dB
… (1.5dB steps)
… (0.75dB steps)
XX1111: +22.5dB
111111: +30dB
ADC PGA Zero Cross Control
1 = Zero cross enabled (volume changes
when signal is zero or after time-out)
0 = Zero cross disabled (volume changes
immediately)
6
GRR
0
Right ADC PGA Gain Range Control
1 = Extended
0 = Standard
5:0
RECVOLR
000000
Right ADC Recording Volume Control
Standard (GRR=0)
Extended (GRR=1)
XX0000 = 0dB
000000 = -17.25dB
… (1.5dB steps)
… (0.75dB steps)
XX1111 = +22.5dB
XX1111 = +30dB
Table 12 Record Gain Register
The output of the Record PGA can also be mixed into the phone and/or headphone outputs (see
“Audio Mixers”). This makes it possible to use the ALC function for the microphone signal in a
smartphone application.
w
PP, Rev 3.3, November 2011
35
WM9713L
Pre-Production
REGISTER
ADDRESS
14h
BIT
15:14
LABEL
R2H
DEFAULT
11 (mute)
Record
Routing
DESCRIPTION
Record Mux to Headphone Mixer Path
Control
00 = stereo
01 = left ADC only
10 = right ADC only
11=mute left and right
13:11
R2HVOL
010 (0dB)
Record Mux to Headphone Mixer Path
Volume Control
000 = +6dB
… (+3dB steps)
111 = -15dB
10:9
R2M
11 (mute)
Record Mux to Mono Mixer Path Control
00 = stereo
01 = left record mux only
10 = right record mux only
11 = mute left and right
8
R2MBST
0 (OFF)
Record Mux to Headphone Mixer Boost
Control
1 = +20dB
0 = 0dB
Table 13 Record PGA Routing Control
w
PP, Rev 3.3, November 2011
36
WM9713L
Pre-Production
AUTOMATIC LEVEL CONTROL
The WM9713L has an automatic level control that aims to keep a constant recording volume
irrespective of the input signal level. This is achieved by continuously adjusting the PGA gain so that
the signal level at the ADC input remains constant. A digital peak detector monitors the ADC output
and changes the PGA gain if necessary.
input
signal
PGA
gain
signal
after
ALC
ALC
target
level
hold
time
decay
time
attack
time
Figure 19 ALC Operation
The ALC function is enabled using the ALCSEL control bits. When enabled, the recording volume can
be programmed between –6dB and –28.5dB (relative to ADC full scale) using the ALCL register bits.
HLD, DCY and ATK control the hold, decay and attack times, respectively.
HOLD TIME
Hold time is the time delay between the peak level detected being below target and the PGA gain
n
beginning to ramp up. It can be programmed in power-of-two (2 ) steps, e.g. 2.67ms, 5.33ms,
10.67ms etc. up to 43.7s. Alternatively, the hold time can also be set to zero. The hold time only
applies to gain ramp-up, there is no delay before ramping the gain down when the signal level is
above target.
DECAY (GAIN RAMP-UP) TIME
Decay time is the time that it takes for the PGA gain to ramp up across 90% of its range (e.g. from
–15B up to 27.75dB). The time it takes for the recording level to return to its target value therefore
depends on both the decay time and on the gain adjustment required. If the gain adjustment is small,
n
it will be shorter than the decay time. The decay time can be programmed in power-of-two (2 ) steps,
from 24ms, 48ms, 96ms, etc. to 24.58s.
ATTACK (GAIN RAMP-DOWN) TIME
Attack time is the time that it takes for the PGA gain to ramp down across 90% of its range (e.g. from
27.75dB down to –15B gain). The time it takes for the recording level to return to its target value
therefore depends on both the attack time and on the gain adjustment required. If the gain adjustment
is small, it will be shorter than the attack time. The attack time can be programmed in power-of-two
n
(2 ) steps, from 6ms, 12ms, 24ms, etc. to 6.14s.
w
PP, Rev 3.3, November 2011
37
WM9713L
Pre-Production
When operating in stereo, the peak detector takes the maximum of left and right channel peak values,
and any new gain setting is applied to both left and right PGAs, so that the stereo image is preserved.
However, the ALC function can also be enabled on one channel only. In this case, only one PGA is
controlled by the ALC mechanism, while the other channel runs independently with its PGA gain set
through the control register.
When one ADC channel is unused, the peak detector disregards that channel. The ALC function can
also operate when the two ADC outputs are mixed to mono in the digital domain, but not if they are
mixed to mono in the analogue domain, before entering the ADCs.
REGISTER
ADDRESS
62h
BIT
15:14
LABEL
ALCSEL
ALC / Noise
Gate Control
DEFAULT
DESCRIPTION
00
ALC Function Channel Control
(OFF)
00 = ALC disabled
01 = ALC on right channel only
10 = ALC or left channel only
11 = ALC on both left and right channels
13:11
MAXGAIN
111
ALC PGA Gain Limit Control
(+30dB)
000 = -12dB
… (6dB steps)
111 = +30dB
10:9
ZCTIMEOUT
11
ALC Zero Cross Timeout Delay
Control
14
00 = 2 x tBITCLK (1.33ms)
15
01 = 2 x tBITCLK (2.67ms)
16
10 = 2 x tBITCLK (5.33ms)
17
11 = 2 x tBITCLK (10.67ms)
Note: Timeout delay values shown when
BITCLK=12.288MHz
60h
15:12
ALCL
ALC Control
1011
ALC Target Level Control
(-12dB)
0000 = -28.5dBFS
… (1.5dB steps)
1111 = -6dBFS
Note: This is the target signal level at
the ADC input
11:8
HLD
0000
ALC Hold Time Control
(0ms)
0000 = 0ms
0001 = 2.67ms
… (time doubles with every step)
1111 = 43.691s
7:4
DCY
0011
ALC Decay Time Control
(192ms)
0000 = 24ms
… (time doubles with every step)
1010 to 1111 = 24.58s
3:0
ATK
0010
ALC Attack Time Control
(24ms)
0000 = 6ms
… (time doubles with every step)
1010 to 1111 = 6.14s
Table 14 ALC Control
w
PP, Rev 3.3, November 2011
38
WM9713L
Pre-Production
MAXIMUM GAIN
The MAXGAIN register sets the maximum gain value that the PGA can be set to whilst under the
control of the ALC. This has no effect on the PGA when ALC is not enabled.
PEAK LIMITER
To prevent clipping when a large signal occurs just after a period of quiet, the ALC circuit includes a
limiter function. If the ADC input signal exceeds 87.5% of full scale (–1.16dB), the PGA gain is
ramped down at the maximum attack rate (as when ATK = 0000), until the signal level falls below
87.5% of full scale. This function is automatically enabled whenever the ALC is enabled.
(Note: If ATK = 0000, then the limiter makes no difference to the operation of the ALC. It is designed
to prevent clipping when long attack times are used).
NOISE GATE
When the signal is very quiet and consists mainly of noise, the ALC function may cause “noise
pumping”, i.e. loud hissing noise during silence periods. The WM9713L has a noise gate function that
prevents noise pumping by comparing the signal level at the input pins (i.e. before the record PGA)
against a noise gate threshold, NGTH. Provided that the noise gate function is enabled (NGAT = 1),
the noise gate cuts in when:
Signal level at ADC [dB] < NGTH [dB] + PGA gain [dB] + Mic Boost gain [dB]
This is equivalent to:
Signal level at input pin [dB] < NGTH [dB]
The PGA gain is then held constant (preventing it from ramping up as it normally would when the
signal is quiet). If the NGG bit is set, the ADC output is also muted when the noise gate cuts in.
The table below summarises the noise gate control register. The NGTH control bits set the noise gate
threshold with respect to the ADC full-scale range. The threshold is adjusted in 1.5dB steps. Levels
at the extremes of the range may cause inappropriate operation, so care should be taken with set–up
of the function. Note that the noise gate only works in conjunction with the ALC function, and always
operates on the same channel(s) as the ALC (left, right, both, or none).
REGISTER
ADDRESS
62h
BIT
7
LABEL
NGAT
DEFAULT
0
ALC / Noise
Gate Control
DESCRIPTION
Noise Gate Enable Control
0 = Disabled
1 = Enabled
5
NGG
0
Noise Gate Function Control
0 = Hold PGA gain at last value
1 = Mute ADC output
4:0
NGTH(4:0)
00000
Noise Gate Threshold Control
00000 = -76.5dBFS
… (1.5dB steps)
11111 = -30dBFS
Table 15 Noise Gate Control
w
PP, Rev 3.3, November 2011
39
WM9713L
Pre-Production
AUDIO DACS
STEREO DAC
The WM9713L has a stereo sigma-delta DAC that achieves high quality audio playback at low power
consumption. Digital tone control, adaptive bass boost and 3-D enhancement functions operate on
the digital audio data before it is passed to the stereo DAC. (Contrary to the AC’97 specification, they
have no effect on analogue input signals or signals played through the auxiliary DAC. Nevertheless,
the ID2 and ID5 bits in the reset register, 00h, are set to ‘1’ to indicate that the WM9713L supports
tone control and bass boost.)
The DAC output has a PGA for volume control. The DAC sample rate can be controlled by writing to a
control register (see “Variable Rate Audio”). It is independent of the ADC sample rate.
When not in use the DACs can be separately powered down using the Powerdown register bits DACL
and DACR (register 3Ch, bits [7:6]).
STEREO DAC VOLUME
The volume of the DAC output signal is controlled by a PGA (Programmable Gain Amplifier). Each
DAC can be mixed into the headphone, speaker and mono mixer paths (see “Audio Mixers”)
controlled by register 0Ch.
Each DAC-to-mixer path has an independent mute bit. When all DAC-to-mixer paths are muted the
DAC PGA is muted automatically.
When not in use the DAC PGAs can be powered down using the Powerdown register bits DACL and
DACR (register 3Ch, bits [7:6]).
REGISTER
ADDRESS
0Ch
BIT
15
LABEL
D2H
DEFAULT
1
DAC
Volume
DESCRIPTION
DAC to Headphone Mixer Mute Control
1 = Mute
0 = No mute
14
D2S
1
DAC to Speaker Mixer Mute Control
1 = Mute
0 = No mute
13
D2M
1
DAC to Mono Mixer Mute Control
1 = Mute
0 = No mute
12:8
DACL
01000
Left DAC to Mixers Volume Control
VOL
(0dB)
00000 = +12dB
… (1.5dB steps)
11111 = -34.5dB
4:0
DACR
01000
Right DAC to Mixers Volume Control
VOL
(0dB)
00000 = +12dB
… (1.5dB steps)
11111 = -34.5dB
5Ch
Additional
Functions
(2)
15
AMUTE
0
DAC Automute Status (Read-Only)
0 = DAC not muted
1 = DAC auto-muted
7
AMEN
0
DAC Automute Control
0 = Disabled
1 = Enabled (DAC automatically muted when
digital input is zero)
Table 16 Stereo DAC Volume Control
w
PP, Rev 3.3, November 2011
40
WM9713L
Pre-Production
TONE CONTROL / BASS BOOST
The WM9713L provides separate controls for bass and treble with programmable gains and filter
characteristics. This function operates on digital audio data before it is passed to the audio DACs.
Bass control can take two different forms:
Linear bass control: bass signals are amplified or attenuated by a user
programmable gain. This is independent of signal volume, and very high bass gains
on loud signals may lead to signal clipping.
Adaptive bass boost: The bass volume is amplified by a variable gain. When the
bass volume is low, it is boosted more than when the bass volume is high. This
method is recommended because it prevents clipping, and usually sounds more
pleasant to the human ear.
Treble control applies a user programmable gain, without any adaptive boost function.
Treble, linear bass and 3D enhancement can all produce signals that exceed full-scale. In order to
avoid limiting under these conditions, it is recommended to set the DAT bit to attenuate the digital
input signal by 6dB. The gain at the outputs should be increased by 6dB to compensate for the
attenuation. Cut-only tone adjustment (i.e. bass and treble gains ≤ 0) and adaptive bass boost cannot
produce signals above full-scale and therefore do not require the DAT bit to be set.
REGISTER
ADDRESS
20h
BIT
15
LABEL
BB
DEFAULT
0
DAC Tone
Control
DESCRIPTION
Bass Mode Control
0 = Linear bass control
1 = Adaptive bass boost
12
BC
0
Bass Cut-off Frequency Control
0 = Low (130Hz at 48kHz sampling)
1 = High (200Hz at 48kHz sampling)
11:8
BASS
1111 (off)
Bass Intensity Control
BB=0
BB=1
0000 = +9dB
0000 = 15dB
0001 = +9dB
… (1dB steps)
… (1.5dB steps)
1110 = 1dB
0111 = 0dB
1111 = Bypass (off)
… (1.5dB steps)
1011-1110 = -6dB
1111 = Bypass (off)
6
DAT
0
Pre-DAC Attenuation Control
0 = 0dB
1 = -6dB
4
TC
0
Treble Cut-off Frequency Control
0 = High (8kHz at 48kHz sampling)
1 = Low (4kHz at 48kHz sampling)
3:0
TRBL
1111
(Disabled)
Treble Intensity Control
0000 = +9dB
0001 = +9dB
… (1.5dB steps)
0111 = 0dB
… (1.5dB steps)
1011-1110 = -6dB
1111 = Bypass (off)
Table 17 DAC Tone Control
Note:
1.
w
All cut-off frequencies change proportionally with the DAC sample rate.
PP, Rev 3.3, November 2011
41
WM9713L
Pre-Production
3D STEREO ENHANCEMENT
The 3D stereo enhancement function artificially increases the separation between the left and right
channels by amplifying the (L-R) difference signal in the frequency range where the human ear is
sensitive to directionality. The programmable 3D depth setting controls the degree of stereo
expansion introduced by the function. Additionally, the upper and lower limits of the frequency range
used for 3D enhancement can be selected using the 3DFILT control bits.
REGISTER
ADDRESS
40h
BIT
13
LABEL
3DE
General
Purpose
1Eh
DEFAULT
0
(disabled)
DESCRIPTION
3D Enhancement Control
1 = Enabled
0 = Disabled
5
3DLC
0
DAC 3D
Control
3D Lower Cut-off Frequency Control
1 = High (500Hz at 48kHz sampling)
0 = Low (200Hz at 48kHz sampling)
4
3DUC
0
3D Upper Cut-off Frequency Control
1 = Low (1.5kHz at 48kHz sampling)
0 = High (2.2kHz at 48kHz sampling)
3:0
3DDEPTH
0000
3D Depth Control
0000 = 0%
… (6.67% steps)
1111 = 100%
Table 18 Stereo Enhancement Control
Note:
1.
w
All cut-off frequencies change proportionally with the DAC sample rate.
PP, Rev 3.3, November 2011
42
WM9713L
Pre-Production
VOICE DAC
VXDAC is a 16-bit mono DAC intended for playback of Rx voice signals input via the PCM interface.
Performance has been optimised for operating at 8ks/s or 16ks/s. The VXDAC will function at other
sample rates up to 48ks/s, but this is not recommended.
The analogue output of VXDAC is routed directly into the output mixers. The signal gain into each
mixer can be adjusted at the mixer inputs using control register 18h.
When not in use the VXDAC can be powered down using the Powerdown register bit VXDAC
(register 3Ch, bit 12).
REGISTER
ADDRESS
3Ch
BIT
12
LABEL
VXDAC
DEFAULT
1
Powerdown (1)
DESCRIPTION
VXDAC Disable Control
1 = Disabled
0 = Enabled
15
18h
V2H
1
VXDAC Output
Control
VXDAC to Headphone Mixer Mute
Control
1 = Mute
0 = No mute
14:12
V2HVOL
010
(0dB)
VXDAC to Headphone Mixer Volume
Control
000 = +6dB
… (+3dB steps)
111 = -15dB
11
V2S
1
VXDAC to Speaker Mixer Mute
Control
1 = Mute
0 = No mute
10:8
V2SVOL
010
(0dB)
VXDAC to Speaker Mixer Volume
Control
000 = +6dB
… (+3dB steps)
111 = -15dB
7
V2M
1
VXDAC to Mono Mixer Mute Control
1 = Mute
0 = No mute
6:4
V2MVOL
010
(0dB)
VXDAC to Mono Mixer Volume
Control
000 = +6dB
… (+3dB steps)
111 = -15dB
Table 19 VXDAC Control
Note:
1.
w
In order to minimise power consumption, the following sequence should be executed
before disabling the Voice DAC:
R44h = 0280h
wait at least 3 AC link frames for mode to change
R44h = 0F80h
Run Voice DAC at fs=6 kHz
R3Ch: bit 12 = 1
Disable Voice DAC. This write must occur immediately after the
write to register R44h.
Run Voice DAC at fs=48 kHz
PP, Rev 3.3, November 2011
43
WM9713L
Pre-Production
AUXILIARY DAC
AUXDAC is a simple 12-bit mono DAC. It can be used to generate DC signals (with the numeric input
written into a control register), or AC signals such as telephone-quality ring tones or system beeps
(with the input signal supplied through an AC-Link slot). In AC mode (XSLE = 1), the input data is
binary offset coded; in DC mode (XSLE = 0), there is no offset.
The analogue output of AUXDAC is routed directly into the output mixers. The signal gain into each
mixer can be adjusted at the mixer inputs using control register 12h. In slot mode (XSLE = 1), the
AUXDAC also supports variable sample rates (See “Variable Rate Audio” section).
When not in use the auxiliary DAC can be powered down using the Powerdown register bit AUXDAC
(register 3Ch, bit 11).
REGISTER
ADDRESS
3Ch
BIT
11
LABEL
AUXDAC
DEFAULT
0
Powerdown (1)
DESCRIPTION
AUXDAC Disable Control
1 = Disabled
0 = Enabled
64h
15
XSLE
0
AUXDAC Input Select Control
0 = From AUXDACVAL[11:0] (for DC
signals)
AUXDAC Input
Control
1 = From AC-Link (for AC signals)
14:12
AUXDAC
000
SLT
AUXDAC Input Control (XSLE=1)
000 = Slot 5, bits 8-19
001 = Slot 6, bits 8-19
010 = Slot 7, bits 8-19
011 = Slot 8, bits 8-19
100 = Slot 9, bits 8-19
101 = Slot 10, bits 8-19
110 = Slot 11, bits 8-19
111 = Reserved
11:0
AUXDAC
VAL
000h
AUXDAC Input Control (XSLE=0)
000h = Minimum
FFFh = Full scale
w
PP, Rev 3.3, November 2011
44
WM9713L
Pre-Production
REGISTER
ADDRESS
1Ah
BIT
15
LABEL
A2H
DEFAULT
1
AUXDAC Output
Control
DESCRIPTION
AUXDAC to Headphone Mixer Mute
Control
1 = Mute
0 = No mute
14:12
A2HVOL
010
(0dB)
AUXDAC to Headphone Mixer
Volume Control
000 = +6dB
… (+3dB steps)
111 = -15dB
11
A2S
1
AUXDAC to Speaker Mixer Mute
Control
1 = Mute
0 = No mute
10:8
A2SVOL
010
(0dB)
AUXDAC to Speaker Mixer Volume
Control
000 = +6dB
… (+3dB steps)
111 = -15dB
7
A2M
1
AUXDAC to Mono Mixer Mute
Control
1 = Mute
0 = No mute
6:4
A2MVOL
010
(0dB)
AUXDAC to Mono Mixer Volume
Control
000 = +6dB
… (+3dB steps)
111 = -15dB
Table 20 AUXDAC Control
w
PP, Rev 3.3, November 2011
45
WM9713L
Pre-Production
VARIABLE RATE AUDIO / SAMPLE RATE CONVERSION
By using an AC’97 Rev2.2 compliant audio interface, the WM9713L can record and playback at all
commonly used audio sample rates, and offer full split-rate support (i.e. the DAC, ADC and AUXDAC
sample rates are completely independent of each other – any combination is possible).
The default sample rate is 48kHz. If the VRA bit in register 2Ah is set, then other sample rates can be
selected by writing to registers 2Ch, 32h and 2Eh. The AC-Link continues to run at 48k frames per
second irrespective of the sample rate selected. However, if the sample rate is less than 48kHz, then
some frames do not carry an audio sample.
REGISTER
ADDRESS
2Ah
BIT
0
LABEL
VRA
DEFAULT
0 (OFF)
Extended
Audio
Stat/Ctrl
DESCRIPTION
Variable Rate Audio Control
1 = Enable VRA
0 = Disable VRA (ADC and DAC run at
48kHz)
Note: When VRA=1, sample rates are
controlled by 2Ch, 2Eh and 32h
2Ch
15:0
DACSR
Audio DAC
Sample Rate
BB80h
Stereo DAC Sample Rate Control
(48kHz)
1F40h = 8kHz
2B11h = 11.025kHz
2EE0h = 12kHz
3E80h = 16kHz
5622h = 22.05kHz
5DC0h = 24kHz
7D00h = 32kHz
AC44h = 44.1kHz
BB80h = 48kHz
Any other value defaults to the nearest
supported sample rate
32h
15:0
ADCSR
Audio ADC
Sample Rate
2Eh
15:0
AUXDAC
Sample Rate
AUXDA
CSR
BB80h
Stereo ADC Sample Rate Control
(48kHz)
Values as DACSR
BB80h
(48kHz)
AUXDAC Sample Rate Control
Values as DACSR
Table 21 Audio Sample Rate Control
Note:
Changing the ADC and / or DAC sample rate will only be effective if the ADCs and DACs are enabled
and powered up before the sample rate is changed. This is done by setting the relevant bits in
registers 26h and 3Ch, as well as the VRA bit in register 2Ah.
The process is as follows:
w
1.
Enable and power up ADCs and or DACs in registers 26h and 3Ch.
2.
Enable VRA bit in 2Ah, bit 0.
3.
Change the sample rate in the respective register.
PP, Rev 3.3, November 2011
46
WM9713L
Pre-Production
AUDIO INPUTS
The following sections give an overview of the analogue audio input pins and their function. For more
information on recommended external components, please refer to the “Applications Information”
section.
LINE INPUT
The LINEL and LINER inputs are designed to record line level signals, and/or to mix into one of the
analogue outputs.
Both pins are directly connected to the record selector. The record PGA adjusts the recording volume,
controlled by register 12h or by the ALC function.
For analogue mixing, the line input signals pass through a separate PGA, controlled by register 0Ah.
The signals can be mixed into the headphone, speaker and mono mixer paths (see “Audio Mixers”).
Each LINE-to-mixer path has an independent mute bit. When all LINE-to-mixer paths are muted the
line PGA is muted automatically. When the line inputs are not used, the line PGA can be switched off
to save power (see “Power Management” section).
LINEL and LINER are biased internally to the reference voltage VREF. Whenever the inputs are
muted or the device placed into standby mode, the inputs remain biased to VREF using special antithump circuitry to suppress any audible clicks when changing inputs.
REGISTER
ADDRESS
0Ah
BIT
15
LABEL
L2H
DEFAULT
1
DESCRIPTION
LINE to Headphone Mixer Mute Control
1 = Mute
0 = No mute
14
L2S
1
LINE to Speaker Mixer Mute Control
1 = Mute
0 = No mute
13
L2M
1
LINE to Mono Mixer Mute Control
1 = Mute
0 = No mute
12:8
LINEL
01000
LINEL to Mixers Volume Control
VOL
(0dB)
00000 = +12dB
… (1.5dB steps)
11111 = -34.5dB
4:0
LINER
01000
LINER to Mixers Volume Control
VOL
(0dB)
00000 = +12dB
… (1.5dB steps)
11111 = -34.5dB
Table 22 Line Input Control
Additionally, line inputs can be used as single-ended microphone inputs through the record mux to
provide a clickless ALC function by bypassing offset introduced through the microphone pre-amps.
Note that the line inputs to the mixers should all be deselected if this is input configuration is used.
w
PP, Rev 3.3, November 2011
47
WM9713L
Pre-Production
MICROPHONE INPUT
MICROPHONE PRE-AMPS
There are two microphone pre-amplifiers, MPA and MPB, which can be configured in a variety of
ways to accommodate up to 3 selectable differential microphone inputs or 2 differential microphone
inputs operating simultaneously for stereo or noise cancellation. The microphone input circuit is
shown in Figure 20.
Vmid
MIC1
Vmid
22h:
13-12
22h:11-10
00 = +12dB
11 = +30dB
MICA
MIC2A
Vmid
MICB
MIC2B
22h:9-8
00 = +12dB
11 = +30dB
MICCM
Figure 20 Microphone Input Circuit
The input pins used for the microphones are MIC1, MICCM, MIC2A and MIC2B. Note that input pins
MIC2A and MIC2B are multi-function inputs and must be configured for use as microphone inputs
when required. This is achieved using MICCMPSEL[1:0] in register 22h (see Table 23). The input to
microphone pre-amp A can be selected from any of the three microphone inputs MIC1, MIC2A and
MIC2B using MPASEL[1:0]. Each pre-amp has independent boost control from +12dB to +30dB in
four steps. This is controlled by MPABST[1:0] and MPBBST[1:0].
When not in use each microphone pre-amp can be powered down using the Powerdown register bits
MPA and MPB (register 3Eh, bits [1:0]). When disabled the inputs are tied to Vmid (for MIC2A and
MIC2B this only applies when they are selected as microphone inputs, otherwise they are left
floating).
w
PP, Rev 3.3, November 2011
48
WM9713L
Pre-Production
REGISTER
ADDRESS
22h
BIT
LABEL
15:14
MICCMPSEL
DEFAULT
00
DESCRIPTION
MIC2A/MIC2B Pin Function Control
00 = MIC2A and MIC2B are mic inputs
01 = MIC2A mic input only
10 = MIC2B mic input only
11 = MIC2A and MIC2B are not mic inputs
13:12
MPASEL
00
MPA Pre-Amp Source Control
00 = MIC1
01 = MIC2A
10 = MIC2B
11 = Reserved
11:10
MPABST
00
MPA Pre-Amp Volume Control
00 = +12dB
01 = +18dB
10 = +24dB
11 = +30dB
9:8
MPBBST
00
MPB Pre-Amp Volume Control
As MPABST
Table 23 Microphone Pre-amp Control
w
PP, Rev 3.3, November 2011
49
WM9713L
Pre-Production
SINGLE MIC OPERATION
Up to three microphones can be connected in a single-ended configuration. Any one of the three
MICs can be selected as the input to MPA using MPASEL[1:0] (Register 22h, bits 13:12). Only the
microphone on MIC2B can be selected to MPB. Note that MPABST always sets the gain for the
selected MPA input microphone. If MIC2B is the selected input for MPA it is recommended that MPB
is disabled.
DUAL MIC OPERATION
Up to two microphones can be connected in a dual differential configuration. This is suitable for stereo
microphone or noise cancellation applications. Mic1 is connected between the MIC2A and MICCM
inputs and mic2 is connected between the MIC2B and MICCM inputs as shown in Figure 21.
Additionally, another microphone can be supported on MIC1 selected through the MPA input mux.
Note that the microphones can be connected in a single-ended configuration.
Figure 21 Dual Microphone Configuration
w
PP, Rev 3.3, November 2011
50
WM9713L
Pre-Production
MICROPHONE BIASING CIRCUIT
The MICBIAS output provides a low noise reference voltage suitable for biasing electret type
microphones and the associated external resistor biasing network. Refer to the Applications
Information section for recommended external components. The MICBIAS voltage can be altered via
MBVOL in register 22h.
MICBIAS=0.75*AVDD.
When MBVOL=0, MICBIAS=0.9*AVDD and when MBVOL=1,
The microphone bias is driven to a dedicated MICBIAS pin 28 and is enabled by MPOP1EN in
register 22h. It can also be configured to drive out on GPIO8 pin 12 enabled by MPOP2EN in register
22h.
When not in use the microphone bias can be powered down using the Powerdown register bit
MICBIAS (register 3Eh, bit 14).
REGISTER
ADDRESS
22h
BIT
7
LABEL
MBOP2EN
DEFAULT
0 (Off)
DESCRIPTION
MICBIAS Output 2 Enable Control
1 = Enable MICBIAS output on GPIO8 (pin
12)
0 = Disable MICBIAS output on GPIO8 (pin
12)
6
MBOP1EN
1 (On)
MICBIAS Output 1 Enable Control
1 = Enable MICBIAS output on MICBIAS
(pin 28)
0 = Disable MICBIAS output on MICBIAS
(pin 28)
5
MBVOL
0
MICBIAS Output Voltage Control
1 = 0.75 x AVDD
0 = 0.9 x AVDD
Table 24 Microphone Bias Voltage Control
The internal MICBIAS circuitry is shown in Figure 22. Note that the maximum source current
capability for MICBIAS is 3mA. The external biasing resistors therefore must be large enough to limit
the MICBIAS current to 3mA.
Figure 22 Microphone Bias Schematic
w
PP, Rev 3.3, November 2011
51
WM9713L
Pre-Production
MICBIAS CURRENT DETECT
The WM9713L includes a microphone bias current detect circuit with programmable thresholds for the
microphone bias current, above which an interrupt will be triggered. There are two separate interrupt
bits, MICDET to e.g. distinguish between one or two microphones connected to the WM9713L, and
MICSHT to detect a shorted microphone (mic button press). The microphone current detect threshold
is set by MCDTHR[2:0], for MICDET, and MCDSCTHR[1:0] for MICSHT. Thresholds for each code
are shown in Table 25
When not in use the microphone bias current detect circuit can be powered down using the
Powerdown register bit MCD (register 3Eh, bit 15).
See the GPIO and Interrupt Controller sections for details on the interrupt and status readback for
these MICBIAS current detection features.
REGISTER
ADDRESS
22h
BIT
4:2
LABEL
MCDTHR
DEFAULT
000
DESCRIPTION
Mic Detect Threshold Control
000 = 100µA
… (100µA steps)
111 = 800µA
Note: These values are for 3.3V supply and
scale with supply voltage (AVDD).
1:0
MCDSCTR
00
Mic Detect Short Circuit Threshold
Control
00 = 600µA
01 = 1200uA
10 = 1800uA
11 = 2400µA
Note: These values are for 3.3V supply and
scale with supply voltage (AVDD).
Table 25 Microphone Current Detect Control
w
PP, Rev 3.3, November 2011
52
WM9713L
Pre-Production
MICROPHONE PGAS
The microphone pre-amps MPA and MPB drive into two microphone PGAs whose gain is controlled
by register 0Eh. The PGA signals can be routed into the headphone mixers and the mono mixer, but
not the speaker mixer (to prevent forming a feedback loop) controlled by register 10h. When the PGA
signals are not selected as an input to any of the mixers the outputs of the PGAs are muted
automatically.
When not in use the microphone PGAs can be powered down using the Powerdown register bits MA
and MB (register 3Eh, bits [3:2]).
REGISTER
ADDRESS
0Eh
BIT
12:8
LABEL
MICAVOL
Mic PGA
Volume
DEFAULT
DESCRIPTION
01000
MICA PGA Volume Control
(0dB)
00000 = +12dB
… (1.5dB steps)
11111 = -34.5dB
4:0
MICBVOL
01000
MICB PGA Volume Control
(0dB)
00000 = +12dB
… (1.5dB steps)
11111 = -34.5dB
Table 26 Microphone PGA Volume Control
REGISTER
ADDRESS
10h
BIT
7
LABEL
MA2M
DEFAULT
1
MIC Routing
DESCRIPTION
MICA to Mono Mixer Mute Control
1 = Mute
0 = No mute
6
MB2M
1
MICB to Mono Mixer Mute Control
1 = Mute
0 = No mute
5
MIC2MBST
0
MIC to Mono Mixer Boost Control
1 = +20dB
0 = 0dB
4:3
MIC2H
11
MIC to Headphone Mixer Path Control
00 = stereo
01 = MICA only
10 = MICB only
11 = mute MICA and MICB
2:0
MIC2HVOL
010
(0dB)
MIC to Headphone Mixer Path Volume
Control
000 = +6dB
… (+3dB steps)
111 = -15dB
Table 27 Microphone PGA Routing Control
w
PP, Rev 3.3, November 2011
53
WM9713L
Pre-Production
MONOIN INPUT
Pin 20 (MONOIN) is a mono input designed to connect to the receive path of a telephony device. The
pin connects directly to the record selector for phone call recording (Note: to record both sides of a
phone call, one ADC channel should record the MONOIN signal while the other channel records the
MIC signal). The record PGA adjusts the recording volume, and is controlled by register 12h or by the
ALC function (see “Record Gain” and “Automatic Level Control” sections).
REGISTER
ADDRESS
14h
BIT
15:14
LABEL
R2H
DEFAULT
11 (mute)
Record
Routing
DESCRIPTION
Record Mux to Headphone Mixer Path
Control
00 = stereo
01 = left record mux only
10 = right rec mux only
11=mute left and right
13:11
R2HVOL
010 (0dB)
Record Mux to Headphone Mixer Path
Volume Control
000 = +6dB
… (+3dB steps)
111 = -15dB
10:9
R2M
11 (mute)
Record Mux to Mono Mixer Path Control
00 = stereo
01 = left record mux only
10 = right record mux only
11 = mute left and right
8
R2MBST
0 (0dB)
Record Mux to Headphone Mixer Boost
Control
1 = +20dB
0 = 0dB
Table 28 Record PGA Routing Control
To listen to the MONOIN signal, the signal passes through a separate PGA, controlled by register
08h. The signal can be routed into the headphone mixer (for normal phone call operation) and/or the
speaker mixer (for speakerphone operation), but not into the mono mixer (to prevent forming a
feedback loop). When the signal is not selected as an input to any of the mixers the output of the PGA
is muted automatically.
When not in use the MONOIN PGA can be powered down using the Powerdown register bit MOIN
(register 3Eh, bit 4).
MONOIN is biased internally to the reference voltage VREF. Whenever the input is muted or the
device placed into standby mode, the input remains biased to VREF using special anti-thump circuitry
to suppress any audible clicks when changing inputs.
w
PP, Rev 3.3, November 2011
54
WM9713L
Pre-Production
REGISTER
ADDRESS
08h
BIT
15
LABEL
M2H
DEFAULT
1
MONOIN
PGA Vol /
Routing
DESCRIPTION
MONOIN to Headphone Mixer Mute
Control
1 = Mute
0 = No mute
14
M2S
1
MONOIN to Speaker Mixer Mute Control
1 = Mute
0 = No mute
12:8
MONOIN
01000
MONOIN to Mixers Volume Control
VOL
(0dB)
00000 = +12dB
… (1.5dB steps)
11111 = -34.5dB
Table 29 Mono PGA Control
w
PP, Rev 3.3, November 2011
55
WM9713L
Pre-Production
PCBEEP INPUT
Pin 19 (PCBEEP) is a mono, line level input intended for externally generated signal or warning
tones. It is routed directly to the record selector and all three output mixers, without an input amplifier.
The signal gain into each mixer can be independently controlled, with a separate mute bit for each
signal path.
PCBEEP is biased internally to the reference voltage VREF. When the signal is not selected as an
input to any of the mixers the input remains biased to VREF using special anti-thump circuitry to
suppress any audible clicks when changing inputs.
REGISTER
ADDRESS
16h
BIT
15
LABEL
B2H
DEFAULT
1
PCBEEP input
DESCRIPTION
PCBEEP to Headphone Mixer Mute
Control
1 = Mute
0 = No mute
14:12
B2HVOL
010
(0dB)
PCBEEP to Headphone Mixer Volume
Control
000 = +6dB
… (+3dB steps)
111 = -15dB
11
B2S
1
PCBEEP to Speaker Mixer Mute Control
1 = Mute
0 = No mute
10:8
B2SVOL
010
(0dB)
PCBEEP to Speaker Mixer Volume
Control
000 = +6dB
… (+3dB steps)
111 = -15dB
7
B2M
1
PCBEEP to Mono Mixer Mute Control
1 = Mute
0 = No mute
6:4
B2MVOL
010
PCBEEP to Mono Mixer Volume Control
(0dB)
000 = +6dB
… (+3dB steps)
111 = -15dB
Table 30 PCBEEP Control
DIFFERENTIAL MONO INPUT
PCBEEP and MONOIN inputs can be configured to provide a differential mono input. This is achieved
by mixing the two inputs together using the headphone mixers or the speaker mixer. Note that the
gain of the MONOIN PGA must match the gain of the PCBEEP mixer input to achieve a balanced
differential mono input.
w
PP, Rev 3.3, November 2011
56
WM9713L
Pre-Production
AUDIO MIXERS
MIXER OVERVIEW
The WM9713L has four separate low-power audio mixers to cover all audio functions required by
smartphones, PDAs and handheld computers. These mixers are used to drive the audio outputs HPL,
HPR, MONO, SPKL, SPKR, OUT3 and OUT4. There are also two inverters used to provide
differential output signals (e.g. for driving BTL loads)
HEADPHONE MIXERS
There are two headphone mixers, headphone mixer left and headphone mixer right (HPMIXL and
HPMIXR). These mixers are the stereo output driver source. They are used to drive the stereo
outputs HPL and HPR. They can also be used to drive SPKL and SPKR outputs and, when used in
conjunction with OUT3 and OUT4, they can be configured to drive complementary signals through the
two output inverters to support bridge-tied load (BTL) stereo loudspeaker outputs. The following
signals can be mixed into the headphone path:
MONOIN (controlled by register 08h, see “Audio Inputs”)
LINEL/R (controlled by register 0Ah, see “Audio Inputs”)
the output of the Record PGA (controlled by register 14h, see “Audio ADC”,
“Record Gain”)
the stereo DAC signal (controlled by register 0Ch, see “Audio DACs”)
the MIC signal (controlled by register 10h, see “Audio Inputs”)
PC_BEEP (controlled by register 16h, see “Audio Inputs”)
the VXDAC signal (controlled by register 18h, see “Audio DACs”)
the AUXDAC signal (controlled by register 1Ah, see “Auxiliary DAC”)
In a typical smartphone application, the headphone signal is a mix of MONOIN / VXDAC and sidetone
(for phone calls) and the stereo DAC signal (for music playback).
When not in use the headphone mixers can be powered down using the Powerdown register bits
HPLX and HPRX (register 3Ch, bits [3:2]).
SPEAKER MIXER
The speaker mixer (SPKMIX) is a mono source. It is typically used to drive a mono loudspeaker in
BTL configuration. The following signals can be mixed into the speaker path:
MONOIN (controlled by register 08h, see “Audio Inputs”)
LINEL/R (controlled by register 0Ah, see “Audio Inputs”)
the stereo DAC signal (controlled by register 0Ch, see “Audio DACs”)
PC_BEEP (controlled by register 16h, see “Audio Inputs”)
the VXDAC signal (controlled by register 18h, see “Audio DACs”)
the AUXDAC signal (controlled by register 1Ah, see “Auxiliary DAC”)
In a typical smartphone application, the speaker signal is a mix of AUXDAC (for system alerts or ring
tone playback), MONOIN / VXDAC (for speakerphone function), and PC_BEEP (for externally
generated ring tones).
Note that when selected the stereo input pairs LINEL/R and DACL/R are summed and attenuated by 6dB so that 0dBFS signals on each channel sum to give a 0dBFS mono signal.
When not in use the speaker mixer can be powered down using the Powerdown register bit SPKX
(register 3Ch, bit 1).
w
PP, Rev 3.3, November 2011
57
WM9713L
Pre-Production
MONO MIXER
The mono mixer drives the MONO pin. The following signals can be mixed into MONO:
LINEL/R (controlled by register 0Ah, see “Audio Inputs”)
the output of the Record PGA (controlled by register 14h, see “Audio ADC”,
“Record Gain”)
the stereo DAC signal (controlled by register 0Ch, see “Audio DACs”)
the MIC signal (controlled by register 10h, see “Audio Inputs”)
PC_BEEP (controlled by register 16h, see “Audio Inputs”)
the VXDAC signal (controlled by register 18h, see “Audio DACs”)
the AUXDAC signal (controlled by register 12h, see “Auxiliary DAC”)
In a typical smartphone application, the MONO signal is a mix of the amplified microphone signal
(possibly with Automatic Gain Control) and (if enabled) an audio playback signal from the stereo DAC
or the auxiliary DAC.
Note that when selected the stereo input pairs LINEL/R and DACL/R are summed and attenuated by 6dB so that 0dBFS signals on each channel sum to give a 0dBFS mono signal.
When not in use the mono mixer can be powered down using the Powerdown register bit MX (register
3Ch, bit 0).
MIXER OUTPUT INVERTERS
There are two general purpose mixer output inverters, INV1 and INV2. Each inverter can be selected
to drive HPMIXL, HPMIXR, SPKMIX, MONOMIX or { ( HPMIXL + HPMIXR ) / 2 }. The outputs of the
inverters can be used to generate complimentary signals (to drive BTL configured loads) and to
provide greater flexibility in output driver configurations. INV1 can be selected as the source for
SPKL, MONO and OUT3 and INV2 as the source for SPKR and OUT4.
The input source for each inverter is selected using INV1[2:0] and INV2[2:0] in register 1Eh (see
Table 31). When no input is selected the inverter is powered down.
REGISTER
ADDRESS
1Eh
BIT
15:13
LABEL
INV1
DEFAULT
DESCRIPTION
000
INV1 Source Select
(no input)
000 = No input (tri-stated)
001 = MONOMIX
010 = SPKMIX
011 = HPMIXL
100 = HPMIXR
101 = HPMIXMONO
110 = Reserved
111 = VMID
12:10
INV2
000
INV2 Source Select
(no input)
000 = No input (tri-stated)
001 = MONOMIX
010 = SPKMIX
011 = HPMIXL
100 = HPMIXR
101 = HPMIXMONO
110 = Reserved
111 = VMID
Table 31 Mixer Inverter Source Select
w
PP, Rev 3.3, November 2011
58
WM9713L
Pre-Production
ANALOGUE AUDIO OUTPUTS
The following sections give an overview of the analogue audio output pins. The WM9713L has three
outputs capable of driving loads down to 16 (headphone / line drivers) – HPL, HPR and MONO and four outputs capable of driving loads down to 8 (loudspeaker / line drivers) – SPKL, SPKR,
OUT3 and OUT4. The combination of output drivers, mixers and mixer inverters means that many
output configurations can be supported.
For examples of typical output and mixer configurations please refer to the “Typical Output
Configurations” section. For more information on recommended external components, please refer to
the “Applications Information” section.
Each output is driven by a PGA with a gain range of 0dB to -46.5dB in -1.5dB steps. Each PGA has
an input source mux, mute and zero-cross detect circuit (delaying gain changes until a zero-cross is
detected, or after time-out).
HEADPHONE OUTPUTS – HPL AND HPR
The HPL and HPR outputs (pins 39 and 41) are designed to drive a 16 or 32 headphone load.
They can also be used as line outputs. They can be used in and AC coupled or DC coupled (capless)
configuration. The available input sources are HPMIXL/R and Vmid (see Table 32).
REGISTER
ADDRESS
1Ch
BIT
7:6
LABEL
HPL
DEFAULT
00 (Vmid)
DESCRIPTION
HPL Source Control
Output PGA
00 = VMID
Mux Select
01 = No input (tri-stated if HPL is
disabled in 3Eh)
10 = HPMIXL
11 = Reserved
5:4
HPR
00 (Vmid)
HPR Source Control
00 = VMID
01 = No input (tri-stated if HPR is
disabled in 3Eh)
10 = HPMIXR
11 = Reserved
Table 32 HPL / HPR PGA Input Source
The signal volume on HPL and HPR can be independently adjusted under software control by writing
to register 04h.
When not in use HPL and HPR can be powered down using the Powerdown register bits HPL and
HPR (register 3Eh, bits [10:9]). To minimise pops and clicks when the PGA is powered down / up it is
recommended that the Vmid input is selected during the power down / up cycle. This ensures the
same DC level is maintained on the output pin throughout.
w
PP, Rev 3.3, November 2011
59
WM9713L
Pre-Production
REGISTER
ADDRESS
04h
BIT
15
LABEL
MUL
DEFAULT
1 (Mute)
Headphone
Volume
DESCRIPTION
HPL Mute Control
1 = Mute
0 = No mute
14
ZCL
0
HPL Zero Cross Control
1 = Zero cross enabled (change volume
only on zero crossings, or after time-out)
0 = Zero cross disabled (change volume
immediately)
13:8
HPLVOL
000000
HPL Volume Control
(0dB)
000000 = 0dB (maximum)
… (1.5dB steps)
011111 = -46.5dB
1xxxxx = -46.5dB
7
MUR
1 (Mute)
HPR Mute Control
1 = Mute
0 = No mute
6
ZCR
0
HPR Zero Cross Control
1 = Zero cross enabled (change volume
only on zero crossings, or after time-out)
0 = Zero cross disabled (change volume
immediately)
5:0
HPRVOL
000000
(0dB)
HPR Volume Control
000000 = 0dB (maximum)
… (1.5dB steps)
011111 = -46.5dB
1xxxxx = -46.5dB
Table 33 HPL / HPR PGA Control
MONO OUTPUT
The MONO output (pin 31) is designed to drive a 16 headphone load and can also be used as a line
output. The available input sources are MONOMIX, INV1 and Vmid (see Table 34)
REGISTER
ADDRESS
1Ch
BIT
15:14
LABEL
MONO
DEFAULT
00 (Vmid)
DESCRIPTION
MONO Source Control
Output PGA
00 = VMID
Mux Select
01 = No input (tri-stated if MONO is
disabled in 3Eh)
10 = MONOMIX
11 = INV1
Table 34 MONO PGA Input Source
The signal volume on MONO can be independently adjusted under software control by writing to
register 08h.
When not in use MONO can be powered down using the Powerdown register bit MONO (register
3Eh, bit 13). To minimise pops and clicks when the PGA is powered down / up it is recommended that
the Vmid input is selected during the power down / up cycle. This ensures the same DC level is
maintained on the output pin throughout.
w
PP, Rev 3.3, November 2011
60
WM9713L
Pre-Production
REGISTER
ADDRESS
08h
BIT
7
LABEL
MU
DEFAULT
1 (Mute)
MONO Vol
DESCRIPTION
MONO Mute Control
1 = Mute
0 = No mute
6
ZC
0
MONO Zero Cross Control
1 = Zero cross enabled (change volume
only on zero crossings, or after time-out)
0 = Zero cross disabled (change volume
immediately)
5:0
MONOVOL
000000
MONO Volume Control
(0dB)
000000 = 0dB (maximum)
… (1.5dB steps)
011111 = -46.5dB
1xxxxx = -46.5dB
Table 35 Mono PGA Control
SPEAKER OUTPUTS – SPKL AND SPKR
The SPKL and SPKR (pins 35 and 36) are designed to drive a loudspeaker load down to 8 and can
also be used as line outputs and headphone outputs. They are designed to drive an 8 load AC
coupled or in a BTL (capless) configuration. The available input sources are HPMIXL/R, SPKMIXL/R,
INV1/2 and Vmid (see Table 36).
REGISTER
ADDRESS
1Ch
BIT
13:11
LABEL
SPKL
Output PGA
DEFAULT
000
(Vmid)
Mux Select
DESCRIPTION
SPKL Source Control
000 = VMID
001 = No input (tri-stated if SPKL is
disabled in 3Eh)
010 = HPMIXL
011 = SPKMIX
100 = INV1
All other values are reserved
10:8
SPKR
000
(Vmid)
SPKR Source Control
000 = VMID
001 = No input (tri-stated if SPKR is
disabled in 3Eh)
010 = HPMIXR
011 = SPKMIX
100 = INV2
All other values are reserved
Table 36 SPKL / SPKR PGA Input Source
The signal volume on SPKL and SPKR can be independently adjusted under software control by
writing to register 02h.
When not in use SPKL and SPKR can be powered down using the Powerdown register bits SPKL
and SPKR (register 3Eh, bits [8:7]). To minimise pops and clicks when the PGA is powered down / up
it is recommended that the Vmid input is selected during the power down / up cycle. This ensures the
same DC level is maintained on the output pin throughout.
w
PP, Rev 3.3, November 2011
61
WM9713L
Pre-Production
REGISTER
ADDRESS
02h
BIT
15
LABEL
MUL
DEFAULT
1 (Mute)
Speaker
DESCRIPTION
SPKL Mute Control
1 = Mute
Volume
0 = No mute
14
ZCL
0
SPKL Zero Cross Control
1 = Zero cross enabled (change volume
only on zero crossings, or after time-out)
0 = Zero cross disabled (change volume
immediately)
13:8
SPKLVOL
000000
SPKL Volume Control
(0dB)
000000 = 0dB (maximum)
… (1.5dB steps)
011111 = -46.5dB
1xxxxx = -46.5dB
7
MUR
1 (Mute)
SPKR Mute Control
1 = Mute
0 = No mute
6
ZCR
0
SPKR Zero Cross Control
1 = Zero cross enabled (change volume
only on zero crossings, or after time-out)
0 = Zero cross disabled (change volume
immediately)
5:0
SPKRVOL
000000
(0dB)
SPKR Volume Control
000000 = 0dB (maximum)
… (1.5dB steps)
011111 = -46.5dB
1xxxxx = -46.5dB
Table 37 SPKL / SPKR PGA Control
Note:
1.
For BTL speaker drive, it is recommended that both PGAs have the same gain setting.
AUXILIARY OUTPUTS – OUT3 AND OUT4
The OUT3 and OUT4 outputs (pins 37 and 33) are designed to drive a loudspeaker load down to 8
and can also be used as line outputs and headphone outputs. They are designed to drive an 8 load
AC coupled or in a BTL (capless) configuration and can be used as a midrail buffer to drive the
headphone outputs in a capless DC configuration. The available input sources are INV1/2 and Vmid
(see Table 38).
REGISTER
ADDRESS
1Ch
BIT
3:2
LABEL
OUT3
DEFAULT
00 (Vmid)
DESCRIPTION
OUT3 Source Control
Output PGA
00 = VMID
Mux Select
01 = No input (tri-stated if OUT3 is
disabled in 3Eh)
10 = INV1
11 = Reserved
1:0
OUT4
00 (Vmid)
OUT4 Source Control
00 = VMID
01 = No input (tri-stated if OUT4 is
disabled in 3Eh)
10 = INV2
11 = Reserved
Table 38 OUT3 / OUT4 PGA Input Source
w
PP, Rev 3.3, November 2011
62
WM9713L
Pre-Production
The signal volume on OUT3 and OUT4 can be independently adjusted under software control by
writing to register 06h.
When not in use OUT3 and OUT4 can be powered down using the Powerdown register bits OUT3
and OUT4 (register 3Eh, bits [11:12]). To minimise pops and clicks when the PGA is powered down /
up it is recommended that the Vmid input is selected during the power down / up cycle. This ensures
the same DC level is maintained on the output pin throughout.
REGISTER
ADDRESS
06h
BIT
15
LABEL
MU4
DEFAULT
1 (Mute)
Speaker
DESCRIPTION
OUT4 Mute Control
1 = Mute
Volume
0 = No mute
14
ZC4
0
OUT4 Zero Cross Control
1 = Zero cross enabled (change volume
only on zero crossings, or after time-out)
0 = Zero cross disabled (change volume
immediately)
13:8
OUT4VOL
000000
OUT4 Volume Control
(0dB)
000000 = 0dB (maximum)
… (1.5dB steps)
011111 = -46.5dB
1xxxxx = -46.5dB
7
MU3
1 (Mute)
OUT3 Mute Control
1 = Mute
0 = No mute
6
ZC3
0
OUT3 Zero Cross Control
1 = Zero cross enabled (change volume
only on zero crossings, or after time-out)
0 = Zero cross disabled (change volume
immediately)
5:0
OUT3VOL
000000
(0dB)
OUT3 Volume Control
000000 = 0dB (maximum)
… (1.5dB steps)
011111 = -46.5dB
1xxxxx = -46.5dB
Table 39 OUT3 / OUT4 PGA Control
THERMAL SENSOR
The speaker and headphone outputs can drive very large currents. To protect the WM9713L from
becoming too hot, a thermal sensor has been built in. If the chip temperature reaches approximately
150C, and the TSHUT bit is cleared, and the GP11 bit is set, the WM9713L deasserts TI, a virtual
GPIO that can be set up to generate an interrupt to the CPU (see “GPIO and Interrupt Control”
section).
w
PP, Rev 3.3, November 2011
63
WM9713L
Pre-Production
REGISTER
ADDRESS
BIT
3Ch
13
LABEL
TSHUT
DEFAULT
DESCRIPTION
1
(disabled)
Thermal Sensor Disable Control
1
Thermal Sensor Polarity Control
1 = Disabled
0 = Enabled
4Eh
11
GP11
1 = Active Low
0 = Active High
54h
11
TI
0
Thermal Sensor Status Bit (Virtual GPIO)
See also “GPIO and Interrupt Control” section.
GP11 = 1 (default)
GP11 = 0
1 = Temp < 150C
1 = Temp > 150C
0 = Temp > 150C
0 = Temp < 150C
Table 40 Thermal Shutdown Control
w
PP, Rev 3.3, November 2011
64
WM9713L
Pre-Production
JACK INSERTION AND AUTO-SWITCHING
In a phone application, a BTL ear speaker may be connected across MONO and HPL, a stereo
headphone on HPL and HPR and stereo speakers on SPKL, SPKR, OUT3 and OUT4 (see Figure
23). Typically, only one of these three output devices is used at any given time: when no headphone
is plugged in, the BTL ear speaker or stereo speakers are active, otherwise the headphone is used.
Figure 23 Typical Output Configuration
The presence of a headphone can be detected using one of GPIO1/6/7/8 (pins 44, 3, 11 & 12) and an
external pull-up resistor (see Figure 43, page 132 for a circuit diagram). When the jack is inserted, the
GPIO is pulled low by a switch on the socket. When the jack is removed the GPIO is pulled high by a
resistor. If the JIEN bit is set, the WM9713L automatically switches between headphone and any
other output configuration, typically ear speaker or stereo speaker that has been set up in the
Powerdown and Output PGA Mux Select registers.
Note:
Please refer to WAN_0182 for further information on jack detect configuration.
In addition to the typical configuration explained above, the WM9713L can also support automatic
switching between the following three configurations set as BTL ear speaker and headphone.
REGISTER
ADDRESS
24h
BIT
1:0
LABEL
EARSPKSEL
Output Volume
Mapping (Jack
Insert)
DEFAULT
00
DESCRIPTION
Ear Speaker Source Control
00 = Default, no ear speaker
configuration selected.
01 = MONO and HPL driver selected
as BTL ear speaker.
10 = OUT3 and HPL driver selected as
BTL ear speaker.
11 = OUT4 and HPL driver selected as
BTL ear speaker.
Table 41 Ear Speaker Configuration
For example if OUT4 and HPL is selected as the BTL ear speaker, the user should select
EARSPKSEL = 3h, then OUT4 is tri-stated on jack insert to prevent sound across the ear speaker
during headphone operation and HPL volume is set to OUT4 volume on jack out to ensure correct ear
speaker operation. It should be noted that all other outputs except HPL, HPR and selected ear
w
PP, Rev 3.3, November 2011
65
WM9713L
Pre-Production
speaker driver are disabled and internally connected to VREF on jack insert. This maintains VREF at
those outputs and helps prevent pops when the outputs are enabled.
Finally if the user wishes to DC couple the headphone outputs the user needs to select between
OUT3 and OUT4 as the mid-rail output buffer driver. The selected mid-rail output buffer is enabled on
jack insert. On jack out it defaults to whatever configuration has been set up in the Powerdown and
Output PGA Mux Select registers.
REGISTER
ADDRESS
BIT
24h
3:2
LABEL
DEFAULT
DCDRVSEL
00
Output Volume
Mapping (Jack
Insert)
DESCRIPTION
Jack Insert Headphone DC Reference
Control
00 = AC coupled headphones, no DC
source
01 = OUT3 is mid-rail output buffer
10 = Reserved
11 = OUT4 is mid-rail output buffer
Table 42 DC Coupled Headphone Configuration
In summary:
JIEN not set: Outputs work as normal as selected in the Powerdown and Output PGA Mux Select
registers.
JIEN set: On jack insert GPIO1/6/7/8 is pulled low, HPL and HPR are enabled, DCDRVSEL decides if
the headphones are DC or AC coupled and configures OUT3 or OUT4 to suit, EARSPKSEL decides
if MONO, OUT3 or OUT4 need to be tri-stated to ensure no sound out on the ear-speaker and finally
all other outputs are disabled as explained above to prevent pops on re-enabling.
On jack out GPIO1/6/7/8 is pulled high, the outputs work as normal as selected in the Powerdown
and Output PGA Mux Select registers except that HPL Volume is controlled by EARSPKSEL to
ensure correct ear speaker operation.
REGISTER
ADDRESS
BIT
24h Output
Volume
Mapping
(Jack
Insert)
4
5Ah
Additional
Functions
(1)
7:6
LABEL
DEFAULT
JIEN
0 (OFF)
DESCRIPTION
Jack Insert Control
0 = Disable jack insert circuitry
1 = Enable jack insert circuitry
JSEL
00
(GPIO1)
Jack Detect Pin Input Control
00 = GPIO1
01 = GPIO6
10 = GPIO7
11 = GPIO8
Table 43 Jack Insertion / Auto-Switching (1)
w
PP, Rev 3.3, November 2011
66
SPKR STATE
User
Controlled
HZ
HZ
HZ
HZ
User
Controlled
User
Controlled
HZ
User
Controlled
HZ
HZ
HZ
HZ
User
Controlled
User
Controlled
HZ
OUT4 STATE
User
Controlled
HZ
HZ
HZ
Tri-Stated
User
Controlled
User
Controlled
Tri-Stated
OUT3 STATE
User
Controlled
HZ
HZ
Tri-Stated
HZ
User
Controlled
User
Controlled
VMID
MONO STATE
User
Controlled
HZ
Tri-Stated
HZ
HZ
GPIO1
OUT4 Ear Speaker
Selected.
HZ
Jack Insert Detection
Enabled. Headphone
plugged out.
User
Controlled
1
User
Controlled
XX
HPR VOLUME
11
User
Controlled
1
HPR Volume
Jack Insert Detection
Enabled.
Headphone plugged out.
No Ear Speaker Selected.
HPR Volume
1
HPR Volume
XX
HPR Volume
00
HPR Volume
1
User
Controlled
Jack Insert Detection
Enabled.
Headphone plugged in.
OUT4 Ear Speaker
Selected.
OUT3 DC Coupled
Headphone Selected.
User
Controlled
0
HPR STATE
01
User
Controlled
11
Enabled
1
Enabled
Jack Insert Detection
Enabled.
Headphone plugged in.
OUT4 Ear Speaker
Selected.
AC Coupled Headphone
Selected.
Enabled
0
Enabled
00
Enabled
11
User
Controlled
1
User
Controlled
Jack Insert Detection
Enabled.
Headphone plugged in.
OUT3 Ear Speaker
Selected.
AC Coupled Headphone
Selected.
HPL VOLUME
0
User
Controlled
00
HPL Volume
10
HPL Volume
1
HPL Volume
Jack Insert Detection
Enabled.
Headphone plugged in.
MONO Ear Speaker
Selected.
AC Coupled Headphone
Selected.
HPL Volume
0
HPL Volume
00
User
Controlled
01
OUT4
Volume
1
HPL STATE
Jack Insert Detection
Enabled.
Headphone plugged in.
No Ear Speaker Selected.
AC Coupled Headphone
Selected.
User
Controlled
0
Enabled
00
Enabled
00
Enabled
1
Enabled
Jack Insert Detection
Disabled.
Enabled
X
User
Controlled
DCDRVSEL
XX
User
Controlled
EARSPKSEL
XX
JIEN
0
MODE DESCRIPTION
SPKL STATE
WM9713L
Pre-Production
Table 44 Jack Insertion / Auto-Switching (2)
w
PP, Rev 3.3, November 2011
67
WM9713L
Pre-Production
DIGITAL AUDIO (S/PDIF) OUTPUT
The WM9713L supports the S/PDIF standard. Pins 48 & 12 can be used to output the S/PDIF data.
Note that pins 48 & 12 can also be used as GPIO pins. The GE5 & GE8 bits (register 56h, bit 5 & bit
8) select between GPIO and S/PDIF functionality for pins 48 & 12 respectively (see “GPIO and
Interrupt control” section).
Register 3Ah is a read/write register that controls S/PDIF functionality and manages bit fields
propagated as channel status (or sub-frame in the V case). With the exception of V, this register
should only be written to when the S/PDIF transmitter is disabled (S/PDIF bit in register 2Ah is ‘0’).
Once the desired values have been written to this register, the contents should be read back to
ensure that the sample rate in particular is supported, then S/PDIF validity bit SPCV in register 2Ah
should be read to ensure the desired configuration is valid. Only then should the S/PDIF enable bit in
register 2Ah be set. This ensures that control and status information start up correctly at the
beginning of S/PDIF transmission.
w
PP, Rev 3.3, November 2011
68
WM9713L
Pre-Production
REGISTER
ADDRESS
2Ah
BIT
10
LABEL
SPCV
DEFAULT
0
Extended
Audio
DESCRIPTION
S/PDIF Validity Bit (Read Only)
1 = Valid
0 = Not valid
5:4
SPSA
01
S/PDIF Slot Assignment Control
00 = Slots 3 and 4
01 = Slots 6 and 9
10 = Slots 7 and 8
11 = Slots 10 and 11
Note: This control is only valid when ADCO=0
in 5Ch
2
SEN
0
S/PDIF Output Enable Control
1 = Enabled
0 = Disabled
3Ah
S/PDIF
Control
Register
15
V
0
S/PDIF Validity Bit
1 = Valid
0 = Not valid
14
DRS
0
Indicates that the WM9713L does not support
double rate S/PDIF output (read-only)
13:12
SPSR
10
Indicates that the WM9713L only supports
48kHz sampling on the S/PDIF output (readonly)
11
L
0
S/PDIF L-bit Control
10:4
CC
0000000
Programmed as required by user
S/PDIF Category Code Control
Category code; programmed as required by
user
3
PRE
0
S/PDIF Pre-emphasis Indication Control
0 = no pre-emphasis
1 = 50/15µs pre-emphasis
2
COPY
0
S/PDIF Copyright Indication Control
0 = Copyright not asserted
1 = Copyright asserted
1
AUDIB
0
S/PDIF Non-audio Indication Control
0 = PCM data
1 = Non-PCM data (e.g. DD or DTS)
0
PRO
0
S/PDIF Professional Indication Control
0 = Consumer mode
1 = Professional mode
5Ch
4
ADCO
Additional
Function
Control
0
S/PDIF Data Source Control
0 = From SDATAOUT (pin 5)
1 = Output from audio ADC
Note: Slot selected by SPSA in 2Ah
Table 45 S/PDIF Output Control
w
PP, Rev 3.3, November 2011
69
WM9713L
Pre-Production
TOUCHPANEL INTERFACE
The WM9713L includes a touchpanel driver and digitiser circuit for use with 4-wire or 5-wire resistive
touchpanels. The following functions are implemented:
X co-ordinate measurement
Y co-ordinate measurement
Pen down detection, with programmable sensitivity
Touch pressure measurement (4-wire touchpanel only)
Auxiliary measurement from COMP1/AUX1 (pin 29), COMP2/AUX2 (pin 30), or
WIPER/AUX4 (pin 12)
The touchpanel digitiser uses a very low power, 12-bit successive approximation type ADC. The
same ADC can also be used for battery and auxiliary measurements (see the “Battery Alarm and
Battery Measurement” and “Auxiliary ADC Inputs” sections).
An on-chip switch matrix connects each touchpanel terminal to the supply voltage TPVDD, to ground
(TPGND), or to the ADC input, as required.
Figure 24 Touchpanel Switch Matrix
w
PP, Rev 3.3, November 2011
70
WM9713L
Pre-Production
PRINCIPLE OF OPERATION - FOUR-WIRE TOUCHPANEL
Four-wire touchpanels are connected to the WM9713L as follows:
Right side contact = X+ (pin 14)
Left side contact = X- (pin 16)
Top side contact = Y+ (pin 15)
Bottom side contact = Y- (pin 17)
The principle of operation is illustrated below (Note: the illustrations assume that the top plate is used
for X and the bottom plate for Y measurements, although the reverse is also possible).
Figure 25 X Co-ordinate Measurement on 4-wire Touchpanel
For an X co-ordinate measurement, the X+ pin is internally switched to TPVDD and X- to TPGND.
The X plate becomes a potential divider, and the voltage at the point of contact is proportional to its X
co-ordinate. This voltage is measured on the Y+ and Y- pins, which carry no current (hence there is
no voltage drop in RY+ or RY-).
Due to the ratiometric measurement method, the supply voltage does not affect measurement
accuracy. The voltage references VREF+ and VREF- are taken from after the matrix switches, so that
any voltage drop in these switches has no effect on the ADC measurement.
Figure 26 Y Co-ordinate Measurement on 4-wire Touchpanel
Y co-ordinate measurements are similar to X co-ordinate measurements, with the X and Y plates
interchanged.
w
PP, Rev 3.3, November 2011
71
WM9713L
Pre-Production
Figure 27 Pen Down Detection on 4-wire Touchpanel
Pen down detection uses a zero power comparator (effectively a CMOS logic gate) with an internal,
programmable pull-up resistor RPU that controls pen-down sensitivity. Increasing RPU makes the
touchpanel less sensitive to touch, while lowering RPU makes it more sensitive.
When the touchpanel is not being touched, no current flows in the circuit, and the PENDOWN signal
is low. When the panel is touched with a pen or finger, current flows through RPU and the panel, and
the comparator output goes high.
The PENDOWN signal can be read from bit 15 in register 7Ah (labeled PNDN). It can also be
observed on pin 46 (GPIO3 / PENDOWN), if the pin is not used for GPIO (GE3=0). Additionally,
PENDOWN is passed to the GPIO logic block (register 54h, bit 13), where it can generate CPU
interrupts, and / or to wake up the WM9713L from sleep mode (see “GPIO and Interrupt Control”
section).
Figure 28 Touch Pressure Measurement on 4-wire Touchpanel
Touch pressure can be determined indirectly by measuring the contact resistance RC between the top
and bottom plates. RC decreases as the touch pressure on the panel increases. The WM9713L
measures RC by sending a constant current IP through the touchpanel and measuring the potential on
each plate. The two values are subtracted in the digital domain to obtain the potential difference,
which is proportional to RC.
To suit different types of touchpanels, the magnitude of IP can be set to either 400A or 200A using
the PIL control bit.
w
PP, Rev 3.3, November 2011
72
WM9713L
Pre-Production
PRINCIPLE OF OPERATION - FIVE-WIRE TOUCHPANEL
Five-wire touchpanels are connected to the WM9713L as follows:
Top sheet contact = WIPER/AUX4 (pin 12)
Top left corner of bottom sheet = TL (pin 16)
Top right corner of bottom sheet = TR (pin 15)
Bottom left corner of bottom sheet = BL (pin 17)
Bottom right corner of bottom sheet = BR (pin 14)
Figure 29 X Co-ordinate Measurement on 5-wire Touchpanel
For an X co-ordinate measurement, the top left and bottom left corners of the touchpanel are
grounded internally to the WM9713L, while the top right and bottom right contacts are connected to
TPVDD. The bottom plate becomes a potential divider with a voltage gradient in the X direction. The
voltage at the point of contact is proportional to its X co-ordinate. This voltage is measured on the
WIPER pin and converted to a digital value by the ADC.
Due to the ratiometric measurement method, the supply voltage does not affect measurement
accuracy. The voltage references VREF+ and VREF- are taken from after the matrix switches, so that
any voltage drop in these switches has no effect on the ADC measurement.
Figure 30 Y Co-ordinate Measurement on 5-wire Touchpanel
w
PP, Rev 3.3, November 2011
73
WM9713L
Pre-Production
Y co-ordinate measurements are similar to Y co-ordinate measurements. However, the voltage
gradient on the bottom plate is in the Y direction instead of the X direction. This is achieved by
grounding the bottom left and bottom right corners of the touchpanel, and connecting the top left and
top right contacts to TPVDD.
Figure 31 Pen Down Detection on 5-wire Touchpanel
Pen down detection works in a similar fashion for both 4-wire and 5-wire touchpanels (see Four-Wire
Touchpanel Operation). On a 5-wire touchpanel, all four contacts of the bottom plate are grounded,
and the top plate contact is connected to the internal programmable pull-up resistor, RPU.
w
PP, Rev 3.3, November 2011
74
WM9713L
Pre-Production
CONTROLLING THE TOUCHPANEL DIGITISER
All touchpanel functions are accessed and controlled through the AC-Link interface.
PHYSICAL CHARACTERISTICS
The physical characteristics of the touchpanel interface are controlled through register 78h, as shown
below.
REGISTER
ADDRESS
78h
BIT
12
LABEL
45W
DEFAULT
0 (4-wire)
DESCRIPTION
Touchpanel Type Control
0 = 4-wire
1 = 5-wire
8
PIL
0 (200A)
Pressure Measurement Current Control
0 = IP = 200A
1 = IP = 400A
0:5
RPU
000001
Internal Pull-up Resistor Control
(64k)
000000 = Reserved
000001 = 64kΩ/1 (most sensitive)
000010 = 64kΩ/2
000011 = 64kΩ/3
… (64kΩ/binary value of RPU)
111111 = 64kΩ/63 (least sensitive)
Note: used to adjust sensitivity of Pen Down
detection
Table 46 Touchpanel Digitiser Control (Physical Characteristics)
POWER MANAGEMENT
To save power, the touchpanel digitiser and the pen-down detector can be independently disabled
when they are not used. The power consumption of the pen-down detector is normally negligible,
except when the pen is down.
The pen ADC is powered-down using PADCPD, register 3Ch bit 15.
The state of the digitiser and pen down detector is controlled by the following bits.
REGISTER
ADDRESS
3Ch
BIT
15
LABEL
PADCPD
DEFAULT
1 = off
DESCRIPTION
Touchpanel / AUXADC Disable Control
1 = Disabled
0 = Enabled
78h
15:14
PRP
00
Touchpanel Digitiser Power State
Control
00 = Pen digitiser off, pen detect off, no
wake-up on pen down (default)
01 = Pen digitiser powered off, pen detect
enabled, touchpanel digitiser wakes up
(changes to state 11) on pen-down
10 = Pen digitiser off, pen detect enabled,
no wake-up on pen down
11 = Pen digitiser and pen detect enabled
13
RPR
0
Pen Detect Wake-up Mode Control
0 = Wake-up the AC-Link only (hold
SDATAIN high until controller sends warm
reset or cold reset)
1 = Wake-up the WM9713L without waiting
for a reset signal from the controller
Table 47 Touchpanel Digitiser Control (Power Management)
w
PP, Rev 3.3, November 2011
75
WM9713L
Pre-Production
INITIATION OF MEASUREMENTS
The WM9713L touchpanel interface supports both polling routines and DMA (direct memory access)
to control the flow of data from the touchpanel ADC to the host CPU.
In a polling routine, the CPU starts each measurement individually by writing to the POLL bit (register
74h, bit 9). This bit automatically resets itself when the measurement is completed.
REGISTER
ADDRESS
74h
BIT
9
LABEL
POLL
DEFAULT
0
DESCRIPTION
Poll Measurement Control
Writing “1” initiates a measurement (when
CTC=0)
8
CTC
0
AUXADC Measurement Mode
0 = Polling mode
1 = Continuous mode (for DMA)
76h
9:8
CR
00
Continuous Mode Conversion Rate
Continuous mode rate (DEL ≠ 1111)
00: 93.75 Hz (every 512 AC-Link frames)
01: 120 Hz (every 400 AC-Link frames)
10: 153.75 Hz (every 312 AC-Link frames)
11: 187.5Hz (every 256 AC-Link frames)
Continuous mode “fast rate” (DEL = 1111)
00: 8 kHz (every six AC-Link frames)
01: 12 kHz (every four AC-Link frames)
10: 24 kHz (every other AC-Link frame)
11: 48 kHz (every AC-Link frame)
Note: PENDIV bits in 44h [5:3] should be set
to 111 in 48kHz mode to ensure that
samples occur synchronously on the AC97
data channel
78h
11
PDEN
0
Touchpanel Measurement Pen Status
Control
0 = Measure regardless of pen status
1 = Measure only when pen is down (when
CTC=0 and POLL=1, measurement is
delayed until pen-down; when CTC=1,
measurements are stopped on pen-up)
10
PDPOL
0
PENDOWN Polarity Control
0 = Normal
1 = Inverted
Table 48 Touchpanel Digitiser Control (Initiation of Measurements)
In continuous mode (CTC = 1), the WM9713L autonomously initiates measurements (or sets of
measurements) at the rate set by CR, and supplies the measured data to the CPU on one of the
unused AC’97 time slots. DMA-enabled CPUs can write the data directly into a FIFO without any
intervention by the CPU core. This reduces CPU loading and speeds up the execution of user
programs in handheld systems.
Note that the measurement frequency in continuous mode is also affected by the DEL bits (see
“Touchpanel Settling Time”). The faster rates achieved when DEL = 1111 may be useful when the
ADC is used for auxiliary measurements.
w
PP, Rev 3.3, November 2011
76
WM9713L
Pre-Production
MEASUREMENT TYPES
The ADCSEL control bits determine which type of measurement is performed (see below).
REGISTER
ADDRESS
BIT
74h
7
LABEL
ADCSEL_AUX4
DEFAULT
0
DESCRIPTION
AUX4 Measurement Enable Control
0 = Disable AUX4 measurement (pin 12)
1 = Enable AUX4 measurement (pin 12)
6
ADCSEL_AUX3
0
AUX3 Measurement Enable Control
0 = Disable AUX3 measurement
(SPKVDD/3)
1 = Enable AUX3 measurement
(SPKVDD/3)
5
ADCSEL_AUX2
0
AUX2 Measurement Enable Control
0 = Disable AUX2 measurement (pin 30)
1 = Enable AUX2 measurement (pin 30)
4
ADCSEL_AUX1
0
AUX1 Measurement Enable Control
0 = Disable AUX1 measurement (pin 29)
1 = Enable AUX1 measurement (pin 29)
3
ADCSEL_PRESSURE
0
Pressure Measurement Enable Control
0 = Disable pressure measurement
1 = Enable pressure measurement
2
ADCSEL_Y
0
Y Co-ordinate Measurement Enable
Control
0 = Disable Y co-ordinate measurement
1 = Enable Y co-ordinate measurement
1
ADCSEL_X
0
X Co-ordinate Measurement Enable
Control
0 = Disable X co-ordinate measurement
1 = Enable X co-ordinate measurement
0
COO
0
Co-ordinate Mode Control
0 = Single measurement
1 = Co-ordinate measurement
Table 49 Touchpanel Digitiser Control (Measurement Types)
When COO is ‘0’, the WM9713L performs a single measurement – either in polling mode or
continuously, as indicated by the CTC bit. The type of measurement is specified by the ADCSEL[7:1]
bits. If CTC=0 (polling mode) then only one of the ADCSEL[7:1] bits should be set.
If operating in continuous mode (CTC=1), then more than one ADCSEL[7:1] bit may be set and
selected
conversions
will
be
performed
cyclically
in
the
following
order
=>
“X,Y,PRESSURE,AUX1,AUX2,AUX3,AUX4…”
The co-ordinate mode (COO = ‘1’) makes it easier to obtain co-ordinate pairs rather than single coordinates. In polling-coordinate mode (CTC = ‘0’, COO = ‘1’), the WM9713L performs an X coordinate, then a Y co-ordinate, followed by a single additional measurement determined by
ADCSEL[7:1], then stops. In continuous-coordinate mode (CTC = ‘1’, COO = ‘1’), the WM9713L
continuously repeats a sequence consisting of an X-co-ordinate,Y co-ordinate, then an additional
measurement determined by ADCSEL[7:1]. At least one of the ADCSEL bits must be set in
continuous coordinate mode when CTC = COO = 1). Should more than one of the ADCSEL[7:1] bits
be set during continuous co-ordinate mode then the additional measurement alternates for every set
of three measurements. For example if ADCSEL_AUX1 and ADCSEL_AUX3 were both selected
whilst CTC = ‘1’, COO = ‘1’ then the following sequence of conversions would be performed:
“X,Y,AUX1,X,Y,AUX3,X,Y,AUX1,X,Y,AUX3…”
w
PP, Rev 3.3, November 2011
77
WM9713L
Pre-Production
CONVERSION RATE
As stated previously the conversion rate is specified by the CR bits (reg 76h).
CR may be set to 93.75Hz (every 512 AC-Link Frames), 120Hz (every 400 AC-Link Frames),
153.75Hz (every 312 AC-Link frames) or 187.5Hz (every 256 AC-Link frames).
If only one ADRSEL[7:1] bit is set then each individual conversion occurs at the rate specified by CR.
If multiple ADRSEL[7:1] bits are set then the complete set of conversions requested is completed at
the rate specified by CR.
DATA READBACK
This data is stored in register 7Ah, and can be retrieved by reading the register in the usual manner
(see AC-Link Interface section). Additionally, the data can also be passed to the controller on one of
the AC-Link time slots not used for audio functions.
The output data word of the touchpanel interface consists of three parts:
Pen Status (1 bit) – this is also passed to the GPIO logic block, which can be
programmed to generate an interrupt and/or wake up the WM9713L on pen down
(see GPIO and Interrupt Control).
Output data from the touchpanel ADC (12 bits)
ADCSRC: 3 additional bits that indicate the source of the ADC data. In co-ordinate
mode (COO = ‘1’), the WM9713L schedules different types of measurements
autonomously and so these register bits may be required.
If the data is being read back using the polling method, there are several ways to determine when a
measurement has finished:
Reading back the POLL bit. If it has been reset to ‘0’, then the measurement has finished.
Monitoring the ADA signal, see GPIO and interrupt section. ADA goes high after every
single conversion. If operating in co-ordinate mode (COO=1) then ADA goes high after
every group of 3 conversions.
Reading back 7Ah until the new data appears
REGISTER
ADDRESS
7Ah
BIT
15
LABEL
PNDN
DEFAULT
0
or
AC-Link slot
selected by
SLT
DESCRIPTION
Pen Status (Read-only)
0 = Pen up
1 = Pen down
14:12
ADCSRC
000
Touchpanel ADC Source
000 = No measurement
001 = X co-ordinate measurement
010 = Y co-ordinate measurement
011 = Pressure measurement (4-wire only)
100 = COMP1/AUX1 measurement (pin 29)
101 = COMP2/AUX2 measurement (pin 30)
110 = AUX3 measurements (SPKVDD/3)
111 = WIPER/AUX4 measurement (pin 12)
11:0
ADCD
000h
Touchpanel ADC Data (Read-only)
Bit 0 = LSB
Bit 11 = MSB
78h
9
WAIT
0
Touchpanel ADC Data Control
0 = Overwrite existing data in 7Ah with new
data
1 = Retain existing data in 7Ah until it is read
Table 50 Touchpanel Digitiser Data
w
PP, Rev 3.3, November 2011
78
WM9713L
Pre-Production
When operating in co-ordinate mode (COO=1) there will be 3 results to read back from each set of
measurements – namely X,Y and the third additional measurement. After the co-ordinate set has
finished the X result will be present in register 7Ah. Once this has been read back by the user the Y
result will overwrite register 7Ah, as indicated by ADCSRC. Finally, after the Y result has been read
back, the result of the third, additional, measurement will become present in 7Ah, again indicated by
ADCSRC.
To avoid losing data that has not yet been read, the WM9713L can delay overwriting register 7Ah with
new conversions until the old data has been read. This function is enabled using the WAIT bit, and
applies to both single and co-ordinate conversion mode.
The flow diagram in
Figure 32 shows the timing of touchpanel conversions, and data readback from register 7Ah dependent on the individual settings of the COO, POLL,ADCSEL and CTC bits.
POLL (74h)
Starts a single measurement
CTC (74h)
Starts a co-ordinate measurement at specified conversion
rate
COO (74h)
Enables Co-ordinate mode
ADCSEL (74H)
Specifies the type of measurement to be made
Figure 32 Touchpanel Conversion Flow Diagram
If the SLEN bit is set to ‘1’, then the touchpanel data appears on the AC-Link slot selected by the SLT
control bits, as shown below. The Slot 0 ‘tag’ bit corresponding to the selected time slot is asserted
whenever there is new data on that slot.
w
PP, Rev 3.3, November 2011
79
WM9713L
Pre-Production
REGISTER
ADDRESS
76h
BIT
3
LABEL
SLEN
DEFAULT
0
DESCRIPTION
Slot Readback Enable Control
0 = Disabled (readback through register map
only)
1 = Enabled (readback slot selected by SLT)
2:0
SLT
110
AC’97 Slot for Touchpanel Data Control
000 = Slot 5
001 = Slot 6
010 = Slot 7
011 = Slot 8
100 = Slot 9
101 = Slot 10
110 = Slot 11
111 = Reserved
Table 51 Returning Touchpanel Data Through an AC-Link Time Slot
w
PP, Rev 3.3, November 2011
80
WM9713L
Pre-Production
TOUCHPANEL SETTLING TIME
For accurate touchpanel measurements, some settling time may be required between the switch
matrix applying a voltage across the touchpanel plate and the ADC sampling the signal. This time
delay function is built into the WM9713L and can be programmed as shown below.
REGISTER
ADDRESS
76h
BIT
LABEL
7:4
DEL
DEFAULT
DESCRIPTION
0000
Touchpanel Settling Time Control
(1 frame)
See Table 53 for details
Table 52 Touchpanel Settling Time Control (1)
DEL
DELAY
DELAY
(AC-LINK FRAMES)
(TIME)
0000
1
20.8s
0001
2
41.7s
0010
4
83.3s
0011
8
167s
0100
16
333s
0101
32
667s
0110
48
1ms
0111
64
1.33ms
1000
96
2ms
1001
128
2.67ms
1010
160
3.33ms
1011
192
4ms
1100
224
4.67ms
1101
256
5.33ms
1110
288
6ms
1111
No delay, switch matrix always on
Table 53 Touchpanel Settling Time Control (2)
The total time for co-ordinate or auxiliary measurements to complete is the delay time DEL, plus one
AC-Link frame (20.8s). For a pressure measurement, the time taken is DEL plus two AC-Link frames
(41.6s).
Although the DELAY is variable the maximum value that may be programmed depends on the
number of ADCSEL[7:1] bits set, as shown in the following table. Setting multiple ADCSEL[7:1] bits
leaves less spare AC_Link frames for the DELAY.
w
PP, Rev 3.3, November 2011
81
WM9713L
Pre-Production
NUMBERS
OF
ADCSEL[1:7]
BITS SET
CR SETTING
MAX DELAY
SETTING
1
00 (93.75Hz)
288
1
01 (120Hz)
288
1
10 (153.75Hz)
288
1
11 (187.5Hz)
256
2
00 (93.75Hz)
256
2
01 (120Hz)
192
2
10 (153.75Hz)
128
2
11 (187.5Hz)
128
3, 4
00 (93.75Hz)
96
3, 4
01 (120Hz)
96
3, 4
10 (153.75Hz)
64
3, 4
11 (187.5Hz)
48
5,6,7
00 (93.75Hz)
48
5,6,7
01 (120Hz)
48
5,6,7
10 (153.75Hz)
32
5,6,7
11 (187.5Hz)
16
1 (if COO=1)
00 (93.75Hz)
224
1 (if COO=1)
01 (120Hz)
192
1 (if COO=1)
10 (153.75Hz)
128
1 (if COO=1)
11 (187.5Hz)
96
2,3,4,5,6,7
00 (93.75Hz)
160
01 (120Hz)
128
10 (153.75Hz)
96
11 (187.5Hz)
64
(if COO=1)
2,3,4,5,6,7
(if COO=1)
2,3,4,5,6,7,8
(if COO=1)
2,3,4,5,6,7,8
(if COO=1)
Table 54 Maximum Delay Values
Setting DEL to ‘1111’ reduces the settling time to zero, i.e. measurements begin immediately. This
mode is intended for fast sampling on AUX inputs. It is NOT intended for touchpanel digitisation.
There are several side-effects when DEL is set to ‘1111’:
w
Co-ordinate mode does not work, i.e. the WM9713L behaves as if COO = 0, even if
COO = 1 (see “Measurement Types”)
If X / Y co-ordinate or touch pressure measurements are selected (ADCSEL = 001, 010
or 011), then the switch matrix is constantly on, and current constantly flows in the
touchpanel. This increases power consumption in the system, and is therefore not
recommended for battery powered systems
In continuous mode (CTC = 1), setting DEL = 1111 increases the sampling rate of the
touchpanel ADC (see “Initiation of Measurements”)
PP, Rev 3.3, November 2011
82
WM9713L
Pre-Production
MASK INPUT CONTROL
Sources of glitch noise, such as the signals driving an LCD display, may feed through to the
touchpanel plates and affect measurement accuracy. In order to minimise this effect, a signal may be
applied to MASK (pin 47 / pin 3) to delay or synchronise the sampling of any input to the ADC. The
effect of the MASK signal depends on the MSK bits of register 78h (bits [7:6]), as described below.
REGISTER
ADDRESS
78h
BIT
7:6
LABEL
MSK
DEFAULT
00
DESCRIPTION
Mask Input Control
see Table 56 for details
Table 55 MASK Input Control
MSK[1-0]
EFFECT OF SIGNAL ON MASK PIN
00
Mask has no effect on conversions GPIO input disabled (default)
01
Static; ‘hi’ on MASK pin stops conversions, ‘lo’ has no effect.
10
Edge triggered; rising or falling edge on MASK pin delays conversions
by an amount set in the DEL[3-0] register. Conversions are asynchronous to the
MASK signal.
11
Synchronous mode; conversions wait until rising or falling edge on MASK initiates
cycle; screen starts to be driven when the edge arrives, the conversion sample
being taken a period set by DEL[3-0] after the edge.
Table 56 Controlling the MASK Feature
Note that pin 47 / pin 3 can also be used as a GPIO (see “GPIO and Interrupt Control” section), or to
output the ADA signal (see below).
THE ADA SIGNAL
Whenever data becomes available from the touchpanel ADC, the internal ADA (ADC Data Available)
signal goes high and remains high until the data has been read from register 7Ah (if SLEN = 0) or
until it has been sent out on an AC-Link slot (if SLEN = 1).
ADA goes high either
After every touchpanel ADC conversion (in normal mode, COO=0)
After every set of 3 conversions (co-ordinate mode, COO=1)
ADA can be used to generate an interrupt, if the AW bit (register 52h, bit 12) is set (see “GPIO and
interrupt control” section)
It is also possible to output the ADA signal on pin 47 / pin 3, if this pin is not used as a GPIO. The
GE4/6 bit must be set to ‘0’ to achieve this (see “GPIO and interrupt control” section).
Alternatively, ADA can be read from bit 12 in register 54h.
w
PP, Rev 3.3, November 2011
83
WM9713L
Pre-Production
ADDITIONAL FEATURES
AUXILIARY ADC INPUTS
The ADC used for touchpanel digitisation can also be used for the sole purpose of auxiliary
measurements, provided that it is enabled (register 78h, PRP = 11). The WM9713L has three pins
that can be used as auxiliary ADC inputs:
MIC2A / COMP1 / AUX1 (pin 29)
MIC2B / COMP2 / AUX2 (pin 30)
WIPER / AUX4 (pin 12)
Additionally, the speaker supply (SPKVDD) can be used as an auxiliary ADC input through an on-chip
potential divider giving an input to the auxiliary ADC of SPKVDD/3. This input is referred to as the
AUX3 input (see Figure 24).
Note that pin 12 connects to the wiper of a 5-wire touchpanel wiper function. Auxiliary measurements
taken on pin 12 are only meaningful when it is not connected to a touchpanel (i.e. a 4-wire
touchpanel, or no touchpanel at all, is used). Pins 29 and 30 are also used as comparator inputs (see
Battery Alarm and Battery Measurement), but auxiliary measurements can still be taken on these pins
at any time. The ADCSEL control bits select between different ADC inputs, as shown in Table 57.
The ADCSEL control bits determine which type of measurement is performed (see below). When
performing auxiliary conversions the co-ordinate mode bit, COO, should be off (0).
If CTC=0 then only one of the ADCSEL[7:1] bits should be set. If operating in continuous mode
(CTC=1), then more than one ADCSEL[7:1] bit may be set, and conversions will be performed
cyclically in the following order => “AUX1,AUX2,AUX3,AUX4…” – dependent on which bits are set.
BIT
LABEL
DEFAULT
7
ADCSEL_AUX4
0
DESCRIPTION
REGISTER
ADDRESS
74h
AUX4 Measurement Enable Control
0 = Disable AUX4 measurement (pin 12)
1 = Enable AUX4 measurement (pin 12)
6
ADCSEL_AUX3
0
AUX3 Measurement Enable Control
0 = Disable AUX3 measurement
(SPKVDD/3)
1 = Enable AUX3 measurement (SPKVDD/3)
5
ADCSEL_AUX2
0
AUX2 Measurement Enable Control
0 = Disable AUX2 measurement (pin 30)
1 = Enable AUX2 measurement (pin 30)
4
ADCSEL_AUX1
0
AUX1 Measurement Enable Control
0 = Disable AUX1 measurement (pin 29)
1 = Enable AUX1 measurement (pin 29)
0
COO
0
Co-ordinate Mode Control
0 = Single measurement
1 = Co-ordinate measurement
Note: When not measuring a touchpanel, set
COO=0
Table 57 Auxiliary ADC Measurements
Auxiliary ADC measurements are initiated in the same way as touchpanel measurements, and the
data is returned in the same manner. Please refer to the “Controlling the Touchpanel Interface”
section.
w
PP, Rev 3.3, November 2011
84
WM9713L
Pre-Production
BATTERY ALARM AND ANALOGUE COMPARATORS
The battery alarm function differs from battery measurement in that it does not actually measure the
battery voltage. Battery alarm only indicates “OK”, “Low” or “Dead”. The advantage of the battery
alarm function is that it does not require a clock and can therefore be used in low-power sleep or
standby modes.
Figure 33 Battery Alarm Example Schematic
The typical schematic for a dual threshold battery alarm is shown above. This alarm has two
thresholds, “dead battery” (COMP1) and “low battery” (COMP2). R1, R2 and R3 set the threshold
voltages. Their values can be up to about 1M in order to keep the battery current [IALARM = VBATT /
(R1+R2+R3)] to a minimum (higher resistor values may affect the accuracy of the system as leakage
currents into the input pins become significant).
Dead battery alarm: COMP1 triggers when VBATT < VREF (R1+R2+R3) / (R2+R3)
A dead battery alarm is the highest priority of interrupt in the system. It should immediately save all
unsaved data and shut down the system. The GP15, GS15 and GW15 bits must be set to generate
this interrupt.
Low battery alarm: COMP2 triggers when VBATT < VREF (R1+R2+R3) / R3
A low battery alarm has a lower priority than a dead battery alarm. Since the threshold voltage is
higher than for a dead battery alarm, there is enough power left in the battery to give the user a
warning and/or shut down “gracefully”. When VBATT gets close to the low battery threshold, spurious
alarms are filtered out by the COMP2 delay function.
The purpose of the capacitor C is to remove from the comparator inputs any high frequency noise or
glitches that may be present on the battery (for example, noise generated by a charge pump). It forms
a low pass filter with R1, R2 and R3.
Low pass cutoff fc [Hz] = 1/ (2 C (R1 || (R2+R3)))
Provided that the cutoff frequency is several orders of magnitude lower than the noise frequency fn,
this simple circuit can achieve excellent noise rejection.
Noise rejection [dB] = 20 log (fn / fc)
The circuit shown above also allows for measuring the battery voltage VBATT. This is achieved simply
by setting the touchpanel ADC input to be either COMP1 (ADCSEL = 100) or COMP2 (ADCSEL =
101) (see also Auxiliary ADC Inputs).
w
PP, Rev 3.3, November 2011
85
WM9713L
Pre-Production
The WM9713L has two on-chip comparators that can be used to implement a battery alarm function,
or other functions such as a window comparator. Each comparator has one of its inputs tied to
COMP1 (pin 29) or COMP2 (pin 30), and the other tied to a voltage reference. The voltage reference
can be either internally generated (VREF = AVDD/2) or externally connected on AUX4 (pin 12).
The comparator output signals are passed to the GPIO logic block (see “GPIO and Interrupt Control”
section), where they can be used to send an interrupt to the CPU via the AC-Link or via the IRQ pin,
and / or to wake up the WM9713L from sleep mode. COMP1/AUX1 (pin 29) corresponds to GPIO bit
15 and COMP2/AUX2 (pin30) to bit 14.
REGISTER
ADDRESS
4Eh
BIT
15
LABEL
DEFAULT
CP1
1
DESCRIPTION
COMP1 Polarity Control
0: Alarm when COMP1 voltage is below VREF
1: Alarm when COMP1 voltage is above VREF
Note: see also “GPIO and Interrupt Control”
14
CP2
1
COMP2 Polarity Control
0: Alarm when COMP2 voltage is below VREF
1: Alarm when COMP2 voltage is above VREF
Note: see also “GPIO and Interrupt Control”
5Ah
15:13
COMP2
DEL
000
Low Battery Alarm Delay Control
000 = No delay
13
001 = 2 AC-link frames (0.17s)
14
010 = 2 AC-link frames (0.34s)
15
011 = 2 AC-link frames (0.68s)
16
100 = 2 AC-link frames (1.4s)
17
101 = 2 AC-link frames (2.7s)
18
110 = 2 AC-link frames (5.5s)
19
111 = 2 AC-link frames (10.9s)
Table 58 Comparator Control
REGISTER
ADDRESS
5Ch
Additional
Analogue
Functions
BIT
14
LABEL
DEFAULT
C2REF
0
DESCRIPTION
Comparator 2 Reference Voltage Select
0 = AVDD/2
1 = WIPER/AUX4 (pin 12)
13:12
C2SRC
00
Comparator 2 Signal Source
00 = AVDD/2 when C2REF=1, else COMP1
powered down
01 = COMP1/AUX1 (pin 29)
10 = COMP2/AUX2 (pin 30)
11 = Reserved
11
C1REF
0
Comparator 1 Reference Voltage Select
0 = AVDD/2
1 = WIPER/AUX4 (pin 12)
10:9
C1SRC
00
Comparator 1 Signal Source
00 = AVDD/2 when C1REF=1, else COMP2
powered down
01 = COMP1/AUX1 (pin 29)
10 = COMP2/AUX2 (pin 30)
11 = Reserved
Table 59 Comparator Reference and Source Control
w
PP, Rev 3.3, November 2011
86
WM9713L
Pre-Production
COMP2 DELAY FUNCTION
COMP2 has an optional delay function for use when the input signal is noisy. When COMP2 triggers
and the delay is enabled (i.e. COMP2DEL is non-zero), then GPIO bit 14 does not change state
immediately, and no interrupt is generated. Instead, the WM9713L starts a delay timer and checks
COMP2 again after the delay time has passed. If COMP2 is still active, then the GPIO bit is set and
an interrupt may be generated (depending on the state of the GW14 bit). If COMP2 is no longer
active, the GPIO bit is not set, i.e. all register bits are as if COMP2 had never triggered.
COMP2
TRIGGERS
C2W?
0
END
Inactive
END
[FALSE ALARM]
1
COMP2
DEL?
non-zero
START TIMER
WAIT
time=COMP2DEL
000
SHUT DOWN
TIMER
COMP2?
Active
SET GI14
END
Figure 34 COMP2 Delay Flow Chart
w
PP, Rev 3.3, November 2011
87
WM9713L
Pre-Production
GPIO AND INTERRUPT CONTROL
The WM9713L has eight GPIO pins that operate as defined in the AC’97 Revision 2.2 specification.
Each GPIO pin can be set up as an input or as an output, and has corresponding bits in register 54h
and in slot 12. The state of a GPIO output is determined by sending data through slot 12 of outgoing
frames (SDATAOUT). Data can be returned from a GPIO input by reading the register bit, or
examining slot 12 of incoming frames (SDATAIN). GPIO inputs can be made sticky, and can be
programmed to generate an interrupt, transmitted either through the AC-Link or through a dedicated,
level-mode interrupt pin (GPIO2/IRQ, pin 45).
In addition, the GPIO pins 1, 3, 4 and 5 can be used for the PCM interface by setting bit 15 of register
36h (see “PCM Codec” section). Setting this bit disables any GPIO functions selected on these pins.
REGISTER
ADDRESS
36h
BIT
15
LABEL
CTRL
DEFAULT
0
PCM
CODEC
Control
56h
DESCRIPTION
GPIO Pin Configuration Control
0 = GPIO pins used as GPIOs
1 = GPIO pins used as PCM interface
Note: For PCM interface, one or more of these
pins (depending on master/slave/partial master
mode) must be set up as an output by writing to
register 4Ch (see Table 62)
8:2
GEn
1 (GPIO)
GPIO Pin
Sharing
Toggle GPIO pin function
0: secondary function enabled
1: GPIO enabled
Table 60 GPIO Additional Function Control
GPIO pins 2 to 8 are multi-purpose pins that can also be used for other (non-GPIO / -PCM) purposes,
e.g. as a S/PDIF output or to signal pendown. This is controlled by register 56h (see Table 63)
Note that GPIO6/7/8 each have an additional function independent of the GPIO / auxiliary functions
discussed above. If these pins are to be used as GPIO then the independent function needs to be
disabled using its own control registers, e.g. to use pin 11 as a GPIO then the RESETB function
needs to be disabled (RSTDIS, register 5Ah, bit 8).
Independently of the GPIO pins, the WM9713L also has seven virtual GPIOs. These are signals from
inside the WM9713L, which are treated as if they were GPIO input signals. From a software
perspective, virtual GPIOs are the same as GPIO pins, but they cannot be set up as outputs, and are
not tied to an actual pin. This allows for simple, uniform processing of different types of signals that
may generate interrupts (e.g. pen down, battery warnings, jack insertion, high-temperature warning,
or GPIO signals).
w
PP, Rev 3.3, November 2011
88
WM9713L
Pre-Production
Figure 35 GPIO Logic
GPIO
SLOT
12 BIT
TYPE
PIN NO.
BIT
DESCRIPTION
1
5
GPIO Pin
44
GPIO1
2
6
GPIO Pin
45
GPIO2 / IRQ
enabled only when pin not used as IRQ
3
7
GPIO Pin
46
GPIO3 / PENDOWN
enabled only when pin not used as PENDOWN
4
8
GPIO Pin
47
5
9
GPIO Pin
48
6
10
GPIO Pin
3
7
11
GPIO Pin
11
8
12
GPIO Pin
12
9
13
Virtual GPIO
-
GPIO4 / ADA / MASK
enabled only when pin not used as ADA
GPIO5 / S/PDIF_OUT
enabled only when pin not used as S/PDIF_OUT
GPIO6 / ADA / MASK
Enabled only when pin not used as ADA
GPIO7 / PENDOWN
enabled only when pin not used as PENDOWN
GPIO8 / S/PDIF_OUT
enabled only when pin not used as S/PDIF_OUT
[MICDET]
10
14
Virtual GPIO
[MICSHT]
11
15
Virtual GPIO
[Thermal Cutout]
12
16
Virtual GPIO
[ADA]
13
17
Virtual GPIO
[PEN DOWN]
14
18
Virtual GPIO
[COMP2]
15
19
Virtual GPIO
[COMP1]
Internal microphone bias current detect, generates an interrupt above
a threshold (see MICBIAS Current Detect)
Internal shorted microphone detect, generates an interrupt above a
threshold (see MICBIAS Current Detect)
Internal thermal cutout signal, indicates when internal temperature
reaches approximately 150C (see “Thermal Sensor”)
Internal ADA (ADC Data Available) Signal
enabled only when touchpanel ADC is active
Internal PENDOWN Signal
enabled only when pen-down detection is active
Internal COMP2 output (Low Battery Alarm)
enabled only when COMP2 is on
Internal COMP1 output (Dead Battery Alarm)
enabled only when COMP1 is on
Table 61 GPIO Bits and Pins
w
PP, Rev 3.3, November 2011
89
WM9713L
Pre-Production
Note: GPIO7 (Pin 11) has an independent RESETB function. This must be disabled using RSTDIS (Register 5Ah, bit 8)
before using Pin 11 as a GPIO / PENDOWN.
The properties of the GPIOs are controlled through registers 4Ch to 52h, as shown below.
REGISTER
ADDRESS
BIT
4Ch
n
LABEL
GCn
DEFAULT
1
DESCRIPTION
GPIO Pin Configuration Control
0 = Output
1 = Input (GC9-15 are always inputs)
4Eh
50h
n
n
GPn
GSn
1
0
GPIO Pin Polarity / Type (Note 1)
Input (GCn = 1)
Output (GCn = 0)
0 = Active low
0 = CMOS output
1 = Active high
1 = Open drain
GPIO Pin Sticky Control
0 = Not sticky
1 = Sticky
52h
n
GWn
0
GPIO Pin Wake-up Control
0 = No wake-up (no interrupts generated by
GPIO)
1 = Wake-up (generate interrupts from GPIO)
54h
n
GIn
N/A
GPIO Pin Status
Read = Returns status of GPIO
Write = Writing 0 clears sticky bits
Table 62 GPIO Control
Note 1: Excludes GP11. For Thermal Sensor Polarity Control (GP11) see Table 40 on page 64.
The following procedure is recommended for handling interrupts:
When the controller receives an interrupt, check register 54h. For each GPIO bit in descending order
of priority, check if the bit is ‘1’. If yes, execute corresponding interrupt routine, then write ‘0’ to
corresponding bit in 54h. If no, continue to next lower priority GPIO. After all GPIOs have been
checked, check if interrupt still present or no. If yes, repeat procedure. If no, then jump back to
process that ran before the interrupt.
If the system CPU cannot execute such an interrupt routine, it may be preferable to switch internal
signals (such as PENDOWN) directly onto the GPIO pins. However, in this case the interrupt signals
cannot be made sticky, and more GPIO pins are tied up both on the WM9713L and on the CPU.
w
PP, Rev 3.3, November 2011
90
WM9713L
Pre-Production
REGISTER
ADDRESS
56h
BIT
2
LABEL
GE2
DEFAULT
1
GPIO pins
function
select
DESCRIPTION
GPIO2 (Pin 45) Function Control
0 = Pin 45 is not controlled by GPIO logic
1 = Pin 45 is controlled by GPIO logic
Note: When GE2=0,
set GC2=0 in 4Ch to output IRQ
3
GE3
1
GPIO3 (Pin 46) Function Control
0 = Pin 46 is not controlled by GPIO logic
1 = Pin 46 is controlled by GPIO logic
Note: When GE3=0,
set GC3=0 in 4Ch to output PENDOWN
4
GE4
1
GPIO4 (Pin 47) Function Control
0 = Pin 47 is not controlled by GPIO logic
1 = Pin 47 is controlled by GPIO logic
Note: When GE4=0,
set GC4=0 in 4Ch to output ADA
set GC4=1 in 4Ch to input MASK
5
GE5
1
GPIO5 (Pin 48) Function Control
0 = Pin 48 is not controlled by GPIO logic
1 = Pin 48 is controlled by GPIO logic
Note: When GE5=0,
set GC5=0 in 4Ch to output S/PDIF
6
GE6
1
GPIO6 (Pin 3) Function Control
0 = Pin 3 is not controlled by GPIO logic
1 = Pin 3 is controlled by GPIO logic
Note: When GE6=0,
set GC6=0 in 4Ch to output ADA signal
set GC6=1 in 4Ch to input MASK signal
7
GE7
1
GPIO7 (Pin 11) Function Control
0 = Pin 11 is not controlled by GPIO logic
1 = Pin 11 is controlled by GPIO logic
Note: When GE7=0,
set GC7=0 in 4Ch to output PENDOWN
8
GE8
1
GPIO8 (Pin 12) Function Control
0 = Pin 12 is not controlled by GPIO logic
1 = Pin 12 is controlled by GPIO logic
Note: When GE8=0,
set GC8=0 in 4Ch to output S/PDIF
Table 63 Using GPIO Pins for Non-GPIO Functions
w
PP, Rev 3.3, November 2011
91
WM9713L
Pre-Production
POWER MANAGEMENT
INTRODUCTION
The WM9713L includes the standard power down control register defined by the AC’97 specification
(register 26h). Additionally, it also allows more specific control over the individual blocks of the device
through register Powerdown registers 3Ch and 3Eh. Each particular circuit block is active when both
the relevant bit in register 26h AND the relevant bit in the Powerdown registers 3Ch and 3Eh are set
to ‘0’.
Note that the default power-up condition is all OFF.
AC97 CONTROL REGISTER
REGISTER
ADDRESS
BIT
26h
14
Powerdown/
Status
register
LABEL
PR6
DEFAULT
DESCRIPTION
1
(disabled)
Output PGAs Disable Control
1
(disabled)
Internal Clock Disable Control
1 = Disabled
0 = Enabled
13
PR5
1 = Disabled
0 = Enabled
12
PR4
1
(disabled)
AC-Link Disable Control
1 = Disabled
0 = Enabled
11
PR3
1
(disabled)
Analogue Disable Control
1 = Disabled
0 = Enabled
Note: This control disables VREF, input PGAs,
DACs, ADCs, mixers and outputs
10
PR2
1
(disabled)
Input PGAs and Mixers Disable Control
1 = Disabled
0 = Enabled
9
PR1
1
(disabled)
Stereo DAC Disable Control
1 = Disabled
0 = Enabled
8
PR0
1
(disabled)
Stereo ADC and Record Mux Disable Control
1 = Disabled
0 = Enabled
3
REF
0
VREF Ready (Read Only)
1 = VREF ready
0 = VREF not ready
2
ANL
0
Analogue Mixers Ready (Read Only)
1 = Analogue mixers ready
0 = Analogue mixers not ready
1
DAC
0
Stereo DAC Ready (Read Only)
1 = DAC ready
0 = DAC not ready
0
ADC
0
Stereo ADC Ready (Read Only)
1 = ADC ready
0 = ADC not ready
Table 64 Powerdown and Status Register (Conforms to AC’97 Rev 2.2)
w
PP, Rev 3.3, November 2011
92
WM9713L
Pre-Production
EXTENDED POWERDOWN REGISTERS
REGISTER
ADDRESS
3Ch
BIT
15
LABEL
DEFAULT
PADCPD
1
(disabled)
Powerdown
(1)
DESCRIPTION
Touchpanel / AUXADC Disable Control
1 = Disabled
0 = Enabled
14
VMID1M
1
(disabled)
1Meg VMID String Disable Control
1 = Disabled
0 = Enabled
13
TSHUT
1
(disabled)
Thermal Shutdown Disable Control
1 = Disabled
0 = Enabled
12
VXDAC
1
(disabled)
Voice DAC Disable Control
1 = Disabled
0 = Enabled
11
AUXDAC
1
(disabled)
AUXDAC Disable Control
1 = Disabled
0 = Enabled
10
VREF
1
(disabled)
VREF Disable Control
1 = Disabled
0 = Enabled
9
PLL
1
(disabled)
PLL Disable Control
1 = Disabled
0 = Enabled
7
DACL
1
(disabled)
Left DAC Disable Control (see Note 1)
1 = Disabled
0 = Enabled
6
DACR
1
(disabled)
Right DAC Disable Control (see Note 1)
1
(disabled)
Left ADC Disable Control
1 = Disabled
0 = Enabled
5
ADCL
1 = Disabled
0 = Enabled
4
ADCR
1
(disabled)
Right ADC Disable Control
1 = Disabled
0 = Enabled
3
HPLX
1
(disabled)
Left Headphone Mixer Disable Control
1 = Disabled
0 = Enabled
2
HPRX
1
(disabled)
Right Headphone Mixer Disable Control
1 = Disabled
0 = Enabled
1
SPKX
1
(disabled)
Speaker Mixer Disable Control
1 = Disabled
0 = Enabled
0
MX
1
(disabled)
Mono Mixer Disable Control
1 = Disabled
0 = Enabled
Note: When analogue inputs or outputs are disabled, they are internally connected to VREF
through a large resistor (VREF=AVDD/2 except when VREF and VMID1M are both OFF). This
maintains the potential at that node and helps to eliminate pops when the pins are re-enabled.
Table 65 Extended Power Down Register (1) (Additional to AC’97 Rev 2.2)
Note:
1.
w
When disabling a PGA, always ensure that it is muted first.
PP, Rev 3.3, November 2011
93
WM9713L
Pre-Production
REGISTER
ADDRESS
3Eh
BIT
15
LABEL
DEFAULT
MCD
1
(disabled)
Powerdown
(2)
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
MICBIA
S
1
(disabled)
MONO
1
(disabled)
OUT4
OUT3
HPL
HPR
SPKL
SPKR
LL
LR
MOIN
MA
MB
MPA
MPB
1
(disabled)
1
(disabled)
1
(disabled)
1
(disabled)
1
(disabled)
1
(disabled)
1
(disabled)
1
(disabled
1
(disabled)
1
(disabled)
1
(disabled)
1
(disabled)
1
(disabled)
DESCRIPTION
Microphone Current Detect Disable Control
1 = Disabled
0 = Enabled
Microphone Bias Disable Control (see Note 1)
1 = Disabled
0 = Enabled
MONO PGA Disable Control (see Note 1)
1 = Disabled
0 = Enabled
OUT4 PGA Disable Control (see Note 1)
1 = Disabled
0 = Enabled
OUT3 PGA Disable Control (see Note 1)
1 = Disabled
0 = Enabled
HPL PGA Disable Control (see Note 1)
1 = Disabled
0 = Enabled
HPR PGA Disable Control (see Note 1)
1 = Disabled
0 = Enabled
SPKL PGA Disable Control (see Note 1)
1 = Disabled
0 = Enabled
SPKR PGA Disable Control (see Note 1)
1 = Disabled
0 = Enabled
LINEL PGA Disable Control (see Note 1)
1 = Disabled
0 = Enabled
LINER PGA Disable Control (see Note 1)
1 = Disabled
0 = Enabled
MONOIN PGA Disable Control (see Note 1)
1 = Disabled
0 = Enabled
MICA PGA Disable Control (see Note 1)
1 = Disabled
0 = Enabled
MICB PGA Disable Control (see Note 1)
1 = Disabled
0 = Enabled
Mic Pre-amp MPA Disable Control
1 = Disabled
0 = Enabled
Mic Pre-amp MPB Disable Control
1 = Disabled
0 = Enabled
Note: When analogue inputs or outputs are disabled, they are internally connected to VREF
through a large resistor (VREF=AVDD/2 except when VREF and VMID1M are both OFF). This
maintains the potential at that node and helps to eliminate pops when the pins are re-enabled.
Table 66 Extended Power Down Register (2) (Additional to AC’97 Rev 2.2)
Note:
1. When disabling a PGA, always ensure that it is muted first.
w
PP, Rev 3.3, November 2011
94
WM9713L
Pre-Production
ADDITIONAL POWER MANAGEMENT
Mixer output inverters: see “Mixer output Inverters” section. Inverters are disabled by default.
Touchpanel Interface: see “Controlling the Touchpanel Digitiser / Power Management”. The
touchpanel digitiser is OFF by default.
SLEEP MODE
Whenever the PR4 bit (reg. 26h) is set, the AC-Link interface is disabled, and the WM9713L is in
sleep mode. There is in fact a very large number of different sleep modes, depending on the other
control bits. For example, the low-power standby mode described below is a sleep mode. It is
desirable to use sleep modes whenever possible, as this will save power. The following functions do
not require a clock and can therefore operate in sleep mode:
Analogue-to-analogue audio (DACs and ADCs unused), e.g. phone call mode
Pen-down detection
GPIO and interrupts
Battery alarm / analogue comparators
The WM9713L can awake from sleep mode as a result of
A warm reset on the AC-Link (according to the AC’97 specification)
A signal on a GPIO pin (if the pin is configured as an input, with wake-up enabled –
see “GPIO and Interrupt Control” section)
A virtual GPIO event such as pen-down, battery alarm, etc. (see “GPIO and
Interrupt Control” section)
LOW POWER STANDBY MODE
If all the bits in registers 26h, 3Ch and 3Eh are set except VMID1M (register 3Ch, bit 14), then the
WM9713L is in low-power standby mode and consumes very little current. A 1M resistor string
remains connected across AVDD to generate VREF. This is necessary if the on-chip analogue
comparators are used (see “Battery Alarm and Battery Measurement” section), and helps shorten the
delay between wake-up and playback readiness. If VREF is not required, the 1M resistor string can
be disabled by setting the VMID1M bit, reducing current consumption further.
SAVING POWER AT LOW SUPPLY VOLTAGES
The analogue supplies to the WM9713L can run from 1.8V to 3.6V. By default, all analogue circuitry
on the IC is optimized to run at 3.3V. This set-up is also good for all other supply voltages down to
1.8V. However, at lower voltages, it is possible to save power by reducing the internal bias currents
used in the analogue circuitry. This is controlled as shown below.
REGISTER
ADDRESS
5Ch
BIT
6:5
LABEL
DEFAULT
VBIAS
00
DESCRIPTION
Analogue Bias Optimization Control
0X = Default bias current, optimized for 3.3V
10 = Low bias current, optimized for 2.5V
11 = Lowest bias current, optimized for 1.8V
Table 67 Analogue Bias Selection
POWER ON RESET (POR)
The WM9713L has an internal power on reset (PORB) which ensures that a reset is applied to all
registers until a supply threshold has been exceeded. The POR circuitry monitors the voltage for both
AVDD and DCVDD and will release the internal reset signal once these supplies are both nominally
greater than 1.36V. The internal reset signal is an AND of the PORB and RESETB input signal.
It is recommended that for operation of the WM9713L, all device power rails should be stable before
configuring the device for operation.
w
PP, Rev 3.3, November 2011
95
WM9713L
Pre-Production
REGISTER MAP
R eg
N ame
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
SE4
SE3
SE2
SE1
SE0
ID9
ID8
ID7
ID6
ID5
ID4
ID3
ID2
ID1
ID0
Speaker Volume
M UL
ZCL
SPKLVOL
M UR
ZCR
04h
Headphone Volume
M UL
ZCL
HPLVOL
M UR
06h
OUT3/4 Volume
M U4
ZC4
OUT4VOL
M U3
08h
M 2H
M 2S
0
M ONOINVOL
0Ah
M ONO Vol & M ONOIN PGA Vol
/ Routing
LINEIN PGA Volume / Routing
L2H
L2S
L2M
0Ch
DAC PGA Volume / Routing
D2H
D2S
0Eh
M IC PGA Volume
0
0
10h
M IC Rout ing
0
0
0
12h
Record PGA Volume
14h
Record Routing / M ux Select
16h
PCBEEP Volume / Routing
B2H
B2HVOL
B2S
B2SVOL
B2M
B2M VOL
0
0
0
0
AAA0h
18h
VxDAC Volume / Routing
V2H
V2HVOL
V2S
V2SVOL
V2M
V2M VOL
0
0
0
0
AAA0h
1Ah
AUXDAC Volume / Routing
A2H
A2HVOL
A2S
A2SVOL
A2M
A2M VOL
0
0
0
0
AAA0h
1Ch
Output PGA M ux Select
1Eh
DAC 3D Control & INV M ux
Select
DAC Tone Cont rol
00h
Reset
02h
20h
RM U
8080h
ZCR
HPRVOL
8080h
ZC3
OUT3VOL
8080h
MU
ZC
M ONOVOL
LINELVOL
0
0
0
LINERVOL
E808h
D2M
DACLVOL
0
0
0
DACRVOL
E808h
0
M ICAVOL
0
0
0
M ICBVOL
GRL
0
0
(Extended)
R2H
0
0
0
REC
BST
0
BASS
OUT3
0
3DLC
3DUC
0
DAT
0
TC
3DDEPTH
0000h
TRBL
0F0Fh
Ext ended Audio ID
2Ah
Ext 'd Audio St at/ Ctrl
0
2Ch
Audio DACs Sample Rate
2Eh
AUXDAC Sample Rate
32h
Audio ADCs Sample Rate
36h
PCM codec control
3Ah
SPDIF cont rol
V
DRS
3Ch
Powerdown (1)
3Eh
Powerdown (2)
PADCP
D
M CD
40h
General Purpose
0
VM ID
1M
M IC
BIAS
0
42h
Fast Power-Up Cont rol
0
0
44h
M CLK / PLL Cont rol
0
46h
M CLK / PLL Cont rol
4Ch
GPIO Pin Configuration
1
1
1
4Eh
GPIO Pin Polarit y / Type
C1P
C2P
PP
50h
GPIO Pin Sticky
C1S
C2S
PS
AS
TS
SS
MS
GS8
GS7
GS6
GS5
GS4
GS3
52h
GPIO Pin Wake-Up
C1W
C2W
PW
AW
TW
SW
MW
GW8
GW7
GW6
GW5
GW4
GW3
54h
GPIO Pin Status
C1I
C2I
PI
AI
TI
SI
MI
GI8
GI7
GI6
GI5
GI4
GI3
GI2
56h
GPIO Pin Sharing
58h
GPIO Pull UP/DOWN Ct rl
5Ah
Additional Functions (1)
5Ch
Additional Functions (2)
60h
ALC Cont rol
62h
ALC / Noise Gate Control
64h
AUXDAC input control
74h
Digitiser Reg 1
0
0
0
0
0
0
76h
Digitiser Reg 2
0
0
0
0
0
0
RPR
45W
PDEN
PDPOL
0
0
0
0
M BOP M BOP1 M BVO
2EN
EN
L
0
0
0
M CDTHR
JIEN
0000h
OUT4
26h
M PBBST
D600h
RECSR
HPR
0
8000h
RECVOLR
28h
24h
M PABST
0808h
00DAh
M IC2HVOL
M ICCM PSEL
M PASEL
C880h
RECSL
HPL
0
BC
M B2M M IC2M
M IC2H
BST
GRR
(Ext ended)
0
SPKR
INVB
0
M A2M
ZC
R2M
BST
R2M
SPKL
INVA
0
RECVOLL
R2HVOL
M ONO
BB
6174h
SPKRVOL
M IC Input Select & Bias / Detect
Ctrl
Output Volume M apping (Jack
Insert)
Powerdown Ctrl/St at
22h
D e f a ult
M CDSCTHR
0040h
EARSPKSEL
0000h
0
0
0
0
0
PR6
PR5
PR4
PR3
PR2
PR1
PR0
0
0
0
0
REF
ANL
DAC
ADC
7F00h
ID1
ID0
0
0
REV1
REV0
AM AP
LDAC
SDAC
CDAC
0
0
VRM
SPDIF
DRA
VRA
0405h
0
0
0
0
SPCV
0
0
0
0
0
SEN
0
VRA
SPSA
DCDRVSEL
BB80h
AUXDACSR (Auxiliary DAC Sample Rat e)
BB80h
BB80h
ADCSR (Audio ADCs Sample Rat e)
CTRL
0
M ODE
TSHUT
VDAC
CP
FSP
OSR
CC (Category Code)
DIV
L
SPSR
0410h
DACSR (Audio DACs Sample Rat e)
SEL
WL
4523h
FM T
PRE
COPY
AUD IB
PRO
2000h
FDFFh
VXDA
C
OUT4
AUXD
AC
OUT3
VREF
PLL
1
DACL
DACR
ADCL
ADCR
HPLX
HPRX
SPKX
MX
M ONO
HPL
HPR
SPKL
SPKR
LL
LR
M OIN
MA
MB
M PA
M PB
FFFFh
3DE
0
0
0
0
0
LB
0
0
0
0
0
0
0
0000h
0
0
0
0
0
0
0
M ONO
SPKL
SPKR
HPL
HPR
OUT3
OUT4
0000h
SEXT[6:4]
CLKSR
C
DIVSEL DIVCTL
0
0
SEXT[3:0]
CLKBX
2
PENDIV
CLKAX CLKM U
2
X
PGDATA
0080h
LF
SDM
1
1
1
1
GC8
GC7
GC6
GC5
GC4
GC3
GC2
GC1
0
FFFEh
AP
TP
SP
MP
GP8
GP7
GP6
GP5
GP4
GP3
GP2
GP1
1
FFFFh
GS2
GS1
0
0000h
GW2
GW1
0
0000h
GI1
0
GPIO pins
N[3:0]
PGADDR
0000h
1
1
1
1
1
1
1
GE8
GE7
GE6
GE5
GE4
GE3
GE2
1
0
FFFEh
PU8
PU7
PU6
PU5
PU4
PU3
PU2
PU1
PD8
PD7
PD6
PD5
PD4
PD3
PD2
PD1
4000h
0
0
0
RSTDIS
WAKEE IRQ
N
INV
ASS
0000h
0
COM P2DEL
AMUTE
C2SRC
C2 REF
ALCL (t arget level)
ALCSEL
JSEL
0
AM EN
0
NGAT
HLD (hold time)
M AXGAIN
HPM ODE
VBIAS
ADCO
Die Revision
HPF
0
DCY (decay t ime)
ZCTIM EOUT
AUXDACSLT
XSLE
PRP
C1SRC
C1REF
0
ATK (att ack t ime)
B032h
NGTH (threshold)
NGG
3E00h
AUXDAC VAL
POLL
0000h
ADCSEL
CTC
CR
0000h
DEL
COO
SLEN
78h
Digitiser Reg 3
Digitiser Read Back
7Ch
Vendor ID1
ASCII character “ W”
ASCII charact er “ M ”
574Dh
7Eh
Vendor ID2
ASCII charact er “ L”
Device Identifier
4C13h
ADCSRC
WAIT
PIL
RPU
0000h
0006h
7Ah
PNDN
M SK
SLT
ADCD (TOUCHPANEL ADC Y DATA)
0001h
0000h
Table 68 WM9713L Register Map
Note:
Register 46h provides access to a sub-page address system to set the SPLL[6:0] and K[21:0] register bits (see Table 6).
w
PP, Rev 3.3, November 2011
96
WM9713L
Pre-Production
REGISTER BITS BY ADDRESS
REGISTER
ADDRESS
BIT
LABEL
DEFAULT
DESCRIPTION
REFER TO
00h
14:10
SE [4:0]
11000
Indicates a CODEC from Wolfson Microelectronics
read-only
9:6
ID9:6
0101
Indicates 18 bits resolution for ADCs and DACs
5
ID5
1
Indicates that the WM9713L supports bass boost
4
ID4
1
Indicates that the WM9713L has a headphone
output
3
ID3
0
Indicates that the WM9713L does not support
simulated stereo
2
ID2
1
Indicates that the WM9713L supports bass and
treble control
1
ID1
0
Indicates that the WM9713L does not support
modem functions
0
ID0
0
Indicates that the WM9713L does not have a
dedicated microphone ADC
Intel’s AC’97
Component
Specification,
Revision 2.2,
page 50
Register 00h is a read-only register. Writing any value to this register resets all registers to their default, but does not
change the contents of reg. 00h. Reading the register reveals information about the codec to the driver, as required by the
AC’97 Specification, Revision 2.2
REGISTER
ADDRESS
02h
BIT
15
LABEL
MUL
DEFAULT
1 (mute)
DESCRIPTION
SPKL Mute Control
1 = Mute
REFER TO
Analogue
Audio Outputs
0 = No mute
14
ZCL
0 (disabled)
SPKL Zero Cross Control
1 = Zero cross enabled
0 = Zero cross disabled
13:8
SPKLVOL
000000 (0dB)
SPKL Volume Control
000000 = 0dB (maximum)
… (1.5dB steps)
011111 = -46.5dB
1xxxxx = -46.5dB
7
MUR
1 (mute)
SPKR Mute Control
1 = Mute
0 = No mute
6
ZCR
0 (disabled)
SPKR Zero Cross Control
1 = Zero cross enabled
0 = Zero cross disabled
5:0
SPKRVOL
000000 (0dB)
SPKR Volume Control
000000 = 0dB (maximum)
… (1.5dB steps)
011111 = -46.5dB
1xxxxx = -46.5dB
Register 02h controls the output pins SPKL and SPKR.
w
PP, Rev 3.3, November 2011
97
WM9713L
Pre-Production
REGISTER
ADDRESS
04h
BIT
15
LABEL
MUL
DEFAULT
1 (mute)
DESCRIPTION
HPL Mute Control
1 = Mute
REFER TO
Analogue
Audio Outputs
0 = No mute
14
ZCL
0 (disabled)
HPL Zero Cross Control
1 = Zero cross enabled
0 = Zero cross disabled
13:8
HPL VOL
000000 (0dB)
HPL Volume Control
000000 = 0dB (maximum)
… (1.5dB steps)
011111 = -46.5dB
1xxxxx = -46.5dB
7
MUR
1 (mute)
HPR Mute Control
1 = Mute
0 = No mute
6
ZCR
0 (disabled)
HPR Zero Cross Control
1 = Zero cross enabled
0 = Zero cross disabled
5:0
HPR VOL
000000 (0dB)
HPR Volume Control
000000 = 0dB (maximum)
… (1.5dB steps)
011111 = -46.5dB
1xxxxx = -46.5dB
Register 04h controls the headphone output pins, HPL and HPR.
REGISTER
ADDRESS
06h
BIT
15
LABEL
MU4
DEFAULT
1 (mute)
DESCRIPTION
OUT4 Mute Control
1 = Mute
REFER TO
Analogue
Audio Outputs
0 = No mute
14
ZC4
0 (disabled)
OUT4 Zero Cross Control
1 = Zero cross enabled
0 = Zero cross disabled
13:8
OUT4VOL
000000 (0dB)
OUT4 Volume Control
000000 = 0dB (maximum)
… (1.5dB steps)
011111 = -46.5dB
1xxxxx = -46.5dB
7
MU3
1 (mute)
OUT3 Mute Control
1 = Mute
0 = No mute
6
ZC3
0 (disabled)
OUT3 Zero Cross Control
1 = Zero cross enabled
0 = Zero cross disabled
5:0
OUT3VOL
000000 (0dB)
OUT3 Volume Control
000000 = 0dB (maximum)
… (1.5dB steps)
011111 = -46.5dB
1xxxxx = -46.5dB
Register 06h controls the analogue output pins OUT3 and OUT4.
w
PP, Rev 3.3, November 2011
98
WM9713L
Pre-Production
REGISTER
ADDRESS
08h
BIT
15
LABEL
M2H
DEFAULT
1 (mute)
DESCRIPTION
REFER TO
MONOIN to Headphone Mixer Mute Control
1 = Mute
0 = No mute
14
M2S
1 (mute)
MONOIN to Speaker Mixer Mute Control
Analogue
Inputs;
Analogue
Audio Outputs
1 = Mute
0 = No mute
12:8
MONOINVO
L
01000 (0dB)
MONOIN to Mixers Volume Control
00000 = +12dB
… (1.5dB steps)
11111 = -34.5dB
7
MU
1 (mute)
MONO Mute Control
1 = Mute
0 = No mute
6
ZC
0 (disabled)
MONO Zero Cross Control
1 = Zero cross enabled
0 = Zero cross disabled
5:0
MONOVOL
000000 (0dB)
MONO Volume Control
000000 = 0dB (maximum)
… (1.5dB steps)
011111 = -46.5dB
1xxxxx = -46.5dB
Register 08h controls the analogue output pin MONO and the analogue input pin MONOIN.
REGISTER
ADDRESS
0Ah
BIT
15
LABEL
L2H
DEFAULT
1 (mute)
DESCRIPTION
LINE to Headphone Mixer Mute Control
1 = Mute
0 = No mute
14
L2S
1 (mute)
REFER TO
Analogue
Inputs, Line
Input
LINE to Speaker Mixer Mute Control
1 = Mute
0 = No mute
13
L2M
1 (mute)
LINE to Mono Mixer Mute Control
1 = Mute
0 = No mute
12:8
LINELVOL
01000 (0dB)
LINEL to Mixers Volume Control
00000 = +12dB
… (1.5dB steps)
11111 = -34.5dB
4:0
LINERVOL
01000 (0dB)
LINER to Mixers Volume Control
00000 = +12dB
… (1.5dB steps)
11111 = -34.5dB
Register 0Ah controls the analogue input pins LINEL and LINER.
w
PP, Rev 3.3, November 2011
99
WM9713L
Pre-Production
REGISTER
ADDRESS
0Ch
BIT
15
LABEL
D2H
DEFAULT
1 (mute)
DESCRIPTION
REFER TO
DAC to Headphone Mixer Mute Control
Audio DACs
1 = Mute
0 = No mute
14
D2S
1 (mute)
DAC to Speaker Mixer Mute Control
1 = Mute
0 = No mute
13
D2M
1 (mute)
DAC to Mono Mixer Mute Control
1 = Mute
0 = No mute
12:8
DACLVOL
01000 (0dB)
Left DAC to Mixers Volume Control
00000 = +12dB
… (1.5dB steps)
11111 = -34.5dB
4:0
DACRVOL
01000 (0dB)
Right DAC to Mixers Volume Control
00000 = +12dB
… (1.5dB steps)
11111 = -34.5dB
Register 0Ch controls the audio DACs (but not AUXDAC).
REGISTER
ADDRESS
0Eh
BIT
12:8
LABEL
DEFAULT
MICAVOL
01000 (0dB)
DESCRIPTION
REFER TO
Analogue
Inputs,
Microphone
Input
MICA PGA Volume Control
00000 = +12dB
… (1.5dB steps)
11111 = -34.5dB
4:0
MICBVOL
01000 (0dB)
MICB PGA Volume Control
00000 = +12dB
… (1.5dB steps)
11111 = -34.5dB
Register 0Eh controls the microphone PGA volume (MICA and MICB).
REGISTER
ADDRESS
10h
BIT
7
LABEL
MA2M
DEFAULT
1 (mute)
DESCRIPTION
REFER TO
Analogue
Inputs,
Microphone
Input
MICA to Mono Mixer Mute Control
1 = Mute
0 = No mute
6
MB2M
1 (mute)
MICB to Mono Mixer Mute Control
1 = Mute
0 = No mute
5
MIC2MBST
0 (0dB)
MIC to Mono Mixer Boost Control
1 = +20dB
0 = 0dB
4:3
MIC2H
11 (mute)
MIC to Headphone Mixer Path Control
00 = stereo
01 = MICA only
10 = MICB only
11 = mute MICA and MICB
2:0
MIC2HVOL
010 (0dB)
MIC to Headphone Mixer Path Volume Control
000 = +6dB
… (+3dB steps)
111 = -15dB
Register 10h controls the microphone routing (MICA and MICB).
w
PP, Rev 3.3, November 2011
100
WM9713L
Pre-Production
REGISTER
ADDRESS
12h
BIT
15
LABEL
RMU
DEFAULT
1 (mute)
DESCRIPTION
REFER TO
Audio ADC,
Record Gain
Audio ADC Input Mute Control
1 = Mute
0 = No mute
14
GRL
0 (standard)
Left ADC PGA Gain Range Control
1 = Extended
0 = Standard
13:8
7
RECVOLL
ZC
000000 (0dB)
0 (disabled)
Left ADC Recording Volume Control
Standard (GRL=0)
Extended (GRL=1)
XX0000 = 0dB
000000 = -17.25dB
… (1.5dB steps)
… (0.75dB steps)
XX1111 = +22.5dB
XX1111 = +30dB
ADC PGA Zero Cross Control
1 = Zero cross enabled
0 = Zero cross disabled
6
GRR
0 (standard)
Right ADC PGA Gain Range Control
1 = Extended
0 = Standard
5:0
RECVOLR
000000 (0dB)
Right ADC Recording Volume Control
Standard (GRR=0)
Extended (GRR=1)
XX0000 = 0dB
000000 = -17.25dB
… (1.5dB steps)
… (0.75dB steps)
XX1111 = +22.5dB
XX1111 = +30dB
Register 12h controls the record volume.
w
PP, Rev 3.3, November 2011
101
WM9713L
Pre-Production
REGISTER
ADDRESS
14h
BIT
15:14
LABEL
R2H
DEFAULT
11 (mute)
DESCRIPTION
REFER TO
Record Mux to Headphone Mixer Path Control
00 = stereo
01 = left record mux only
Audio ADC,
Record
Selector
10 = right rec mux only
11=mute left and right
13:11
R2HVOL
010 (0dB)
Record Mux to Headphone Mixer Path Volume
Control
000 = +6dB
… (+3dB steps)
111 = -15dB
10:9
R2M
11 (mute)
Record Mux to Mono Mixer Path Control
00 = stereo
01 = left record mux only
10 = right record mux only
11 = mute left and right
8
R2MBST
0 (0dB)
Record Mux to Headphone Mixer Boost Control
1 = +20dB
0 = 0dB
6
RECBST
0 (0dB)
ADC Record Boost Control
1 = +20dB
0 = 0dB
5:3
RECSL
000 (mic)
Left Record Mux Source Control
000 = MICA (pre-PGA)
001 = MICB (pre-PGA)
010 = LINEL (pre-PGA)
011 = MONOIN (pre-PGA)
100 = HPMIXL
101 = SPKMIC
110 = MONOMIX
111 = Reserved
2:0
RECSR
000 (mic)
Right Record Mux Source Control
000 = MICA (pre-PGA)
001 = MICB (pre-PGA)
010 = LINEL (pre-PGA)
011 = MONOIN (pre-PGA)
100 = HPMIXL
101 = SPKMIC
110 = MONOMIX
111 = Reserved
Register 14h controls the record selector and the ADC to mono mixer path.
w
PP, Rev 3.3, November 2011
102
WM9713L
Pre-Production
REGISTER
ADDRESS
16h
BIT
15
LABEL
B2H
DEFAULT
1 (mute)
DESCRIPTION
REFER TO
PCBEEP to Headphone Mixer Mute Control
1 = Mute
0 = No mute
14:12
B2HVOL
010 (0dB)
Analogue
Inputs,
PCBEEP Input
PCBEEP to Headphone Mixer Volume Control
000 = +6dB
… (+3dB steps)
111 = -15dB
11
B2S
1 (mute)
PCBEEP to Speaker Mixer Mute Control
1 = Mute
0 = No mute
10:8
B2SVOL
010 (0dB)
PCBEEP to Speaker Mixer Volume Control
000 = +6dB
… (+3dB steps)
111 = -15dB
7
B2M
1 (mute)
PCBEEP to Mono Mixer Mute Control
1 = Mute
0 = No mute
6:4
B2MVOL
010 (0dB)
PCBEEP to Mono Mixer Volume Control
000 = +6dB
… (+3dB steps)
111 = -15dB
Register 16h controls the analogue input pin PCBEEP.
REGISTER
ADDRESS
18h
BIT
15
LABEL
V2H
DEFAULT
1 (mute)
DESCRIPTION
REFER TO
VXDAC to Headphone Mixer Mute Control
1 = Mute
0 = No mute
14:12
V2HVOL
010 (0dB)
Audio Mixers,
Side Tone
Control
VXDAC to Headphone Mixer Volume Control
000 = +6dB
… (+3dB steps)
111 = -15dB
11
V2S
1 (mute)
VXDAC to Speaker Mixer Mute Control
1 = Mute
0 = No mute
10:8
V2SVOL
010 (0dB)
VXDAC to Speaker Mixer Volume Control
000 = +6dB
… (+3dB steps)
111 = -15dB
7
V2M
1 (mute)
VXDAC to Mono Mixer Mute Control
1 = Mute
0 = No mute
6:4
V2MVOL
010 (0dB)
VXDAC to Mono Mixer Volume Control
000 = +6dB
… (+3dB steps)
111 = -15dB
Register 18h controls the output signal of the Voice DAC.
w
PP, Rev 3.3, November 2011
103
WM9713L
Pre-Production
REGISTER
ADDRESS
1Ah
BIT
15
LABEL
A2H
DEFAULT
1 (mute)
DESCRIPTION
REFER TO
AUXDAC to Headphone Mixer Mute Control
Auxiliary DAC
1 = Mute
0 = No mute
14:12
A2HVOL
010 (0dB)
AUXDAC to Headphone Mixer Volume Control
000 = +6dB
… (+3dB steps)
111 = -15dB
11
A2S
1 (mute)
AUXDAC to Speaker Mixer Mute Control
1 = Mute
0 = No mute
10:8
A2SVOL
010 (0dB)
AUXDAC to Speaker Mixer Volume Control
000 = +6dB
… (+3dB steps)
111 = -15dB
7
A2M
1 (mute)
AUXDAC to Mono Mixer Mute Control
1 = Mute
0 = No mute
6:4
A2MVOL
010 (0dB)
AUXDAC to Mono Mixer Volume Control
000 = +6dB
… (+3dB steps)
111 = -15dB
Register 1Ah controls the output signal of the auxiliary DAC.
w
PP, Rev 3.3, November 2011
104
WM9713L
Pre-Production
REGISTER
ADDRESS
1Ch
BIT
15:14
LABEL
MONO
DEFAULT
00 (VMID)
DESCRIPTION
REFER TO
Analogue
Audio Outputs
MONO Source Control
00 = VMID
01 = No input (tri-stated if MONO is disabled)
10 = MONOMIX
11 = INV1
13:11
SPKL
000 (VMID)
SPKL Source Control
000 = VMID
001 = No input (tri-stated if SPKL is disabled)
010 = HPMIXL
011 = SPKMIX
100 = INV1
All other values are reserved
10:8
SPKR
000 (VMID)
SPKR Source Control
000 = VMID
001 = No input (tri-stated if SPKR is disabled)
010 = HPMIXR
011 = SPKMIX
100 = INV2
All other values are reserved
7:6
HPL
00 (VMID)
HPL Source Control
00 = VMID
01 = No input (tri-stated if HPL is disabled)
10 = HPMIXL
11 = Reserved
5:4
HPR
00 (VMID)
HPR Source Control
00 = VMID
01 = No input (tri-stated if HPR is disabled)
10 = HPMIXR
11 = Reserved
3:2
OUT3
00 (VMID)
OUT3 Source Control
00 = VMID
01 = No input (tri-stated if OUT3 is disabled)
10 = INV1
11 = Reserved
1:0
OUT4
00 (VMID)
OUT4 Source Control
00 = VMID
01 = No input (tri-stated if OUT4 is disabled)
10 = INV2
11 = Reserved
Register 1Ch controls the inputs to the output PGAs.
w
PP, Rev 3.3, November 2011
105
WM9713L
Pre-Production
REGISTER
ADDRESS
1Eh
BIT
15:13
LABEL
INV1
DEFAULT
000 (no input)
DESCRIPTION
INV1 Source Select
000 = No input (tri-stated)
001 = MONOMIX
REFER TO
Audio Mixers,
Mixer Output
Inverters
010 = SPKMIX
011 = HPMIXL
100 = HPMIXR
101 = HPMIXMONO
110 = Reserved
111 = VMID
12:10
INV2
000 (no input)
INV2 Source Select
000 = No input (tri-stated)
001 = MONOMIX
010 = SPKMIX
011 = HPMIXL
100 = HPMIXR
101 = HPMIXMONO
110 = Reserved
111 = VMID
5
3DLC
0 (low)
3D Lower Cut-off Frequency Control
1 = High (500Hz at 48kHz sampling)
0 = Low (200Hz at 48kHz sampling)
4
3DUC
0 (high)
3D Upper Cut-off Frequency Control
Audio DAC,
Stereo DAC,
3D Stereo
Enhancement
1 = Low (1.5kHz at 48kHz sampling)
0 = High (2.2kHz at 48kHz sampling)
3:0
3DDEPTH
0000 (0%)
3D Depth Control
0000 = 0%
… (6.67% steps)
1111 = 100%
Register 1Eh controls 3D stereo enhancement for the audio DACs and input muxes to the output inverters INV1 and INV2.
w
PP, Rev 3.3, November 2011
106
WM9713L
Pre-Production
REGISTER
ADDRESS
20h
BIT
15
LABEL
BB
DEFAULT
0 (linear)
DESCRIPTION
REFER TO
Audio DACs,
Tone Control /
Bass Boost
Bass Mode Control
0 = Linear bass control
1 = Adaptive bass boost
12
BC
0 (low)
Bass Cut-off Frequency Control
0 = Low (130Hz at 48kHz sampling)
1 = High (200Hz at 48kHz sampling)
11:8
BASS
1111 (off)
Bass Intensity Control
BB=0
BB=1
0000 = +9dB
0000 = 15dB
0001 = +9dB
… (1dB steps)
… (1.5dB steps)
1110 = 1dB
0111 = 0dB
1111 = Bypass (off)
… (1.5dB steps)
1011-1110 = -6dB
1111 = Bypass (off)
6
DAT
0 (0dB)
Pre-DAC Attenuation Control
0 = 0dB
1 = -6dB
4
TC
0 (high)
Treble Cut-off Frequency Control
0 = High (8kHz at 48kHz sampling)
1 = Low (4kHz at 48kHz sampling)
3:0
TRBL
1111 (off)
Treble Intensity Control
0000 = +9dB
0001 = +9dB
… (1.5dB steps)
0111 = 0dB
… (1.5dB steps)
1011-1110 = -6dB
1111 = Bypass (off)
Register 20h controls the bass and treble response of the left and right audio DAC (but not AUXDAC).
w
PP, Rev 3.3, November 2011
107
WM9713L
Pre-Production
REGISTER
ADDRESS
22h
BIT
15:14
LABEL
MICCMP
DEFAULT
00 (mics)
SEL
DESCRIPTION
REFER TO
MIC2A/MIC2B Pin Function Control
00 = MIC2A and MIC2B are microphone inputs
01 = MIC2A microphone input only
10 = MIC2B microphone input only
Analogue
Inputs,
Microphone
Input
11 = MIC2A and MIC2B are not microphone inputs
13:12
MPASEL
00 (MIC1)
MPA Pre-Amp Source Control
00 = MIC1
01 = MIC2A
10 = MIC2B
11 = Reserved
11:10
MPABST
00 (+12dB)
MPA Pre-Amp Volume Control
00 = +12dB
01 = +18dB
10 = +24dB
11 = +30dB
9:8
MPBBST
00 (+12dB)
MPB Pre-Amp Volume Control
00 = +12dB
01 = +18dB
10 = +24dB
11 = +30dB
7
MBOP2EN
0 (disabled)
MICBIAS Output 2 Enable Control
1 = Enable MICBIAS output on GPIO8 (pin 12)
0 = Disable MICBIAS output on GPIO8 (pin 12)
6
MBOP1EN
1 (enabled)
MICBIAS Output 1 Enable Control
1 = Enable MICBIAS output on MICBIAS (pin 28)
0 = Disable MICBIAS output on MICBIAS (pin 28)
5
MBVOL
0 (0.9xAVDD)
MICBIAS Output Voltage Control
1 = 0.75 x AVDD
0 = 0.9 x AVDD
4:2
MCDTHR
000 (100uA)
Mic Detect Threshold Control
000 = 100µA
… (100µA steps)
111 = 800µA
1:0
MCDSCTHR
00 (600uA)
Mic Detect Short Circuit Threshold Control
00 = 600µA
01 = 1200uA
10 = 1800uA
11 = 2400µA
Register 22h controls the microphone input configuration and microphone bias and detect configuration.
w
PP, Rev 3.3, November 2011
108
WM9713L
Pre-Production
REGISTER
ADDRESS
24h
BIT
4
LABEL
JIEN
DEFAULT
0 (disabled)
DESCRIPTION
REFER TO
Jack Insertion
and AutoSwitching
Jack Insert Control
0 = Disable jack insert circuitry
1 = Enable jack insert circuitry
3:2
DCDRVSEL
00 (AC)
Jack Insert Headphone DC Reference Control
00 = AC coupled headphones, no DC source
01 = OUT3 is mid-rail output buffer
10 = Reserved
11 = OUT4 is mid-rail output buffer
1:0
EARSPK
00 (none)
SEL
Ear Speaker Source Control
00 = No ear speaker
01 = MONO and HPL
10 = OUT3 and HPL
11 = OUT4 and HPL
Register 24h controls the output volume mapping on headphone jack insertion.
REGISTER
ADDRESS
26h
BIT
14
LABEL
PR6
DEFAULT
1 (disabled)
DESCRIPTION
REFER TO
Power
Management
Output PGAs Disable Control
1 = Disabled
0 = Enabled
13
PR5
1 (disabled)
Internal Clock Disable Control
1 = Disabled
0 = Enabled
12
PR4
1 (disabled)
AC-Link Disable Control
1 = Disabled
0 = Enabled
11
PR3
1 (disabled)
Analogue Disable Control
1 = Disabled
0 = Enabled
10
PR2
1 (disabled)
Input PGAs and Mixers Disable Control
1 = Disabled
0 = Enabled
9
PR1
1 (disabled)
Stereo DAC Disable Control
1 = Disabled
0 = Enabled
8
PR0
1 (disabled)
Stereo ADC and Record Mux Disable Control
1 = Disabled
0 = Enabled
3
REF
0 (not ready)
VREF Ready (Read Only)
1 = VREF ready
0 = VREF not ready
2
ANL
0 (not ready)
Analogue Mixers Ready (Read Only)
1 = Analogue mixers ready
0 = Analogue mixers not ready
1
DAC
0 (not ready)
Stereo DAC Ready (Read Only)
1 = DAC ready
0 = DAC not ready
0
ADC
0 (not ready)
Stereo ADC Ready (Read Only)
1 = ADC ready
0 = ADC not ready
Register 26h is for power management according to the AC’97 specification. Note that the actual state of many circuit
blocks depends on both register 26h AND registers 3Ch and 3Eh.
w
PP, Rev 3.3, November 2011
109
WM9713L
Pre-Production
REGISTER
ADDRESS
28h
BIT
LABEL
DEFAULT
DESCRIPTION
REFER TO
15:14
ID
00
Indicates that the WM9713L is configured as the
primary CODEC in the system.
11:10
REV
01
Indicates that the WM9713L conforms to AC’97
Rev2.2
9
AMAP
0
Indicates that the WM9713L does not support slot
mapping
8
LDAC
0
Indicates that the WM9713L does not have an LFE
DAC
7
SDAC
0
Indicates that the WM9713L does not have
Surround DACs
6
CDAC
0
Indicates that the WM9713L does not have a
Centre DAC
3
VRM
0
Indicates that the WM9713L does not have a
dedicated, variable rate microphone ADC
2
SPDIF
1
Indicates that the WM9713L supports S/PDIF
output
1
DRA
0
Indicates that the WM9713L does not support
double rate audio
0
VRA
1
Indicates that the WM9713L supports variable rate
audio
read-only
Intel’s AC’97
Component
Specification,
Revision 2.2,
page 59
Register 28h is a read-only register that indicates to the driver which advanced AC’97 features the WM9713L supports.
REGISTER
ADDRESS
2Ah
BIT
10
LABEL
SPCV
DEFAULT
0
DESCRIPTION
REFER TO
S/PDIF Validity Bit (Read Only)
Digital Audio
(S/PDIF)
Output
1 = Valid
0 = Not valid
5:4
SPSA
01 (slots 6, 9)
S/PDIF Slot Assignment Control
00 = Slots 3 and 4
01 = Slots 6 and 9
10 = Slots 7 and 8
11 = Slots 10 and 11
2
SEN
0 (disabled)
S/PDIF Output Enable Control
1 = Enabled
0 = Disabled
0
VRA
0 (OFF)
Variable Rate Audio Control
1 = Enable VRA
0 = Disable VRA (ADC and DAC run at 48kHz)
Register 2Ah controls the S/PDIF output and variable rate audio.
w
PP, Rev 3.3, November 2011
110
WM9713L
Pre-Production
REGISTER
ADDRESS
2Ch
BIT
all
LABEL
DACSR
DEFAULT
BB80h
(48kHz)
DESCRIPTION
REFER TO
Variable Rate
Audio /
Sample Rate
Conversion
Stereo DAC Sample Rate Control
1F40h = 8kHz
2B11h = 11.025kHz
2EE0h = 12kHz
3E80h = 16kHz
5622h = 22.05kHz
5DC0h = 24kHz
7D00h = 32kHz
AC44h = 44.1kHz
BB80h = 48kHz
Any other value defaults to the nearest supported
sample rate
2Eh
all
AUXDACSR
BB80h
(48kHz)
AUXDAC Sample Rate Control
1F40h = 8kHz
2B11h = 11.025kHz
2EE0h = 12kHz
3E80h = 16kHz
5622h = 22.05kHz
5DC0h = 24kHz
7D00h = 32kHz
AC44h = 44.1kHz
BB80h = 48kHz
Any other value defaults to the nearest supported
sample rate
32h
all
ADCSR
BB80h
(48kHz)
Stereo ADC Sample Rate Control
1F40h = 8kHz
2B11h = 11.025kHz
2EE0h = 12kHz
3E80h = 16kHz
5622h = 22.05kHz
5DC0h = 24kHz
7D00h = 32kHz
AC44h = 44.1kHz
BB80h = 48kHz
Any other value defaults to the nearest supported
sample rate
Note: The VRA bit in register 2Ah must be set first to obtain sample rates other than 48kHz
Registers 2Ch, 2Eh 32h and control the sample rates for the stereo DAC, auxiliary DAC and audio ADC, respectively.
w
PP, Rev 3.3, November 2011
111
WM9713L
Pre-Production
REGISTER
ADDRESS
36h
BIT
15
LABEL
CTRL
DEFAULT
DESCRIPTION
REFER TO
0 (GPIO reg)
GPIO Pin Configuration Control
PCM CODEC
0 = GPIO pins used as GPIOs
1 = GPIO pins used as PCM interface
14:13
MODE
10 (master
mode)
PCM Interface Mode Control
00 = PCM interface disabled
01 = Slave mode
10 = Master mode
11 = Partial master mode
11:9
DIV
010 (1/4)
PCMCLK Rate Control
000 = Voice DAC clock
001 = Voice DAC clock / 2
010 = Voice DAC clock / 4
011 = Voice DAC clock / 8
100 = Voice DAC clock / 16
All other values are reserved
8
VDACOSR
0 (64x)
Voice DAC Oversampling Rate Control
0 = 64 x fs
1 = 128 x fs
7
CP
0 (normal)
PCMCLK Polarity Control
0 = Normal
1 = Inverted
6
5:4
FSP
SEL
0 (normal)
00 (normal)
FMT = 00, 01 or 10
FMT = 11
PCMFS Polarity
Control
DSP Mode Control
0 = Normal
0 = DSP Mode A
1 = Inverted
1 = DSP Mode B
PCM ADC Output Channel Control
00 = Normal stereo
01 = Reverse stereo
10 = Output left ADC data only
11 = Output right ADC data only
3:2
WL
10 (24 bits)
PCM Data Word Length Control
00 = 16-bit
01 = 20-bit
10 = 24-bit
11 = 32-bit (not supported when FMT=00)
1:0
FMT
2
10 (I S)
PCM Data Format Control
00 = Right justified
01 = Left justified
2
10 = I S
11 = DSP mode
Register 36h controls the PCM CODEC.
w
PP, Rev 3.3, November 2011
112
WM9713L
Pre-Production
REGISTER
ADDRESS
3Ah
BIT
15
LABEL
V
DEFAULT
0
DESCRIPTION
REFER TO
Digital Audio
(S/PDIF)
Output
S/PDIF Validity Bit
1 = Valid
0 = Not valid
14
DRS
0
Indicates that the WM9713L does not support
double rate S/PDIF output (read-only)
13:12
SPSR
10
Indicates that the WM9713L only supports 48kHz
sampling on the S/PDIF output (read-only)
11
L
0
S/PDIF L-bit Control
10:4
CC
0000000
3
PRE
0
Programmed as required by user
S/PDIF Category Code Control
Category code; programmed as required by user
S/PDIF Pre-emphasis Indication Control
0 = no pre-emphasis
1 = 50/15µs pre-emphasis
2
COPY
0
S/PDIF Copyright Indication Control
0 = Copyright not asserted
1 = Copyright asserted
1
AUDIB
0
S/PDIF Non-audio Indication Control
0 = PCM data
1 = Non-PCM data
0
PRO
0
S/PDIF Professional Indication Control
0 = Consumer mode
1 = Professional mode
Register 3Ah Read/Write. Controls the S/PDIF output.
w
PP, Rev 3.3, November 2011
113
WM9713L
Pre-Production
REGISTER
ADDRESS
3Ch
BIT
15
LABEL
PADCPD
DEFAULT
1 (disabled)
DESCRIPTION
REFER TO
Touchpanel / AUXADC Disable Control
1 = Disabled
Power
Management
0 = Enabled
14
VMID1M
1 (disabled)
1Meg VMID String Disable Control
1 = Disabled
0 = Enabled
13
TSHUT
1 (disabled)
Thermal Shutdown Disable Control
1 = Disabled
0 = Enabled
12
VXDAC
1 (disabled)
Voice DAC Disable Control
1 = Disabled
0 = Enabled
11
AUXDAC
1 (disabled)
AUXDAC Disable Control
1 = Disabled
0 = Enabled
10
VREF
1 (disabled)
VREF Disable Control
1 = Disabled
0 = Enabled
9
PLL
1 (disabled)
PLL Disable Control
1 = Disabled
0 = Enabled
7
DACL
1 (disabled)
Left DAC Disable Control
1 = Disabled
0 = Enabled
6
DACR
1 (disabled)
Right DAC Disable Control
1 = Disabled
0 = Enabled
5
ADCL
1 (disabled)
Left ADC Disable Control
1 = Disabled
0 = Enabled
4
ADCR
1 (disabled)
Right ADC Disable Control
1 = Disabled
0 = Enabled
3
HPLX
1 (disabled)
Left Headphone Mixer Disable Control
1 = Disabled
0 = Enabled
2
HPRX
1 (disabled)
Right Headphone Mixer Disable Control
1 = Disabled
0 = Enabled
1
SPKX
1 (disabled)
Speaker Mixer Disable Control
1 = Disabled
0 = Enabled
0
MX
1 (disabled)
Mono Mixer Disable Control
1 = Disabled
0 = Enabled
* “0” corresponds to “ON”, if and only if the corresponding bit in register 26h is also 0.
Register 3Ch is for power management additional to the AC’97 specification. Note that the actual state of each circuit block
depends on both register 3Ch AND register 26h.
w
PP, Rev 3.3, November 2011
114
WM9713L
Pre-Production
REGISTER
ADDRESS
3Eh
BIT
15
LABEL
MCD
DEFAULT
1 (disabled)
DESCRIPTION
REFER TO
Microphone Current Detect Disable Control
1 = Disabled
Power
Management
0 = Enabled
14
MICBIAS
1 (disabled)
Microphone Bias Disable Control
1 = Disabled
0 = Enabled
13
MONO
1 (disabled)
MONO PGA Disable Control
1 = Disabled
0 = Enabled
12
OUT4
1 (disabled)
OUT4 PGA Disable Control
1 = Disabled
0 = Enabled
11
OUT3
1 (disabled)
OUT3 PGA Disable Control
1 = Disabled
0 = Enabled
10
HPL
1 (disabled)
HPL PGA Disable Control
1 = Disabled
0 = Enabled
9
HPR
1 (disabled)
HPR PGA Disable Control
1 = Disabled
0 = Enabled
8
SPKL
1 (disabled)
SPKL PGA Disable Control
1 = Disabled
0 = Enabled
7
SPKR
1 (disabled)
SPKR PGA Disable Control
1 = Disabled
0 = Enabled
6
LL
1 (disabled)
LINEL PGA Disable Control
1 = Disabled
0 = Enabled
5
LR
1 (disabled)
LINER PGA Disable Control
1 = Disabled
0 = Enabled
4
MOIN
1 (disabled)
MONOIN PGA Disable Control
1 = Disabled
0 = Enabled
3
MA
1 (disabled)
MICA PGA Disable Control
1 = Disabled
0 = Enabled
2
MB
1 (disabled)
MICB PGA Disable Control
1 = Disabled
0 = Enabled
1
MPA
1 (disabled)
Mic Pre-amp MPA Disable Control
1 = Disabled
0 = Enabled
0
MPB
1 (disabled)
Mic Pre-amp MPB Disable Control
1 = Disabled
0 = Enabled
* “0” corresponds to “ON”, if and only if the corresponding bit in register 26h is also 0.
Register 3Eh is for power management additional to the AC’97 specification. Note that the actual state of each circuit block
depends on both register 3Eh AND register 26h.
w
PP, Rev 3.3, November 2011
115
WM9713L
Pre-Production
REGISTER
ADDRESS
40h
BIT
13
LABEL
3DE
DEFAULT
0 (disabled)
DESCRIPTION
3D Enhancement Control
1 = Enabled
0 = Disabled
7
LB
0 (disabled)
Digital Loopback Control
1 = Enabled
0 = Disabled
REFER TO
Audio DACs,
3D Stereo
Enhancement
Intel’s AC’97
Component
Specification,
Revision 2.2,
page 55
Register 40h is a “general purpose” register as defined by the AC’97 specification. Only two bits are implemented in the
WM9713L.
REGISTER
ADDRESS
42h
BIT
6
LABEL
MONO
DEFAULT
0 (normal)
DESCRIPTION
MONO Fast Power Up Control
1 = Fast power up
0 = Normal power up
5
SPKL
0 (normal)
REFER TO
Analogue
Audio Outputs,
Power-Up
SPKL Fast Power Up Control
1 = Fast power up
0 = Normal power up
4
SPKR
0 (normal)
SPKR Fast Power Up Control
1 = Fast power up
0 = Normal power up
3
HPL
0 (normal)
HPL Fast Power Up Control
1 = Fast power up
0 = Normal power up
2
HPR
0 (normal)
HPR Fast Power Up Control
1 = Fast power up
0 = Normal power up
1
OUT3
0 (normal)
OUT3 Fast Power Up Control
1 = Fast power up
0 = Normal power up
0
OUT4
0 (normal)
OUT4 Fast Power Up Control
1 = Fast power up
0 = Normal power up
Register 42h controls power-up conditions for output PGAs.
w
PP, Rev 3.3, November 2011
116
WM9713L
Pre-Production
REGISTER
ADDRESS
44h
BIT
14:12
LABEL
SEXT[6:4]
DEFAULT
000 (div 1)
DESCRIPTION
REFER TO
Hi-Fi Block Clock Division Control
Clock
000 = f
Generation
001 = f/2
…
111 = f/8
11:8
SEXT[3:0]
0000 (div 1)
Voice DAC Clock Division Control
0000 = f
0001 = f/2
…
1111 = f/16
7
CLKSRC
1 (external)
AC97 CLK Source Control
1 = External clock
0 = PLL clock
5:3
PENDIV
000 (f/16)
AUXADC Clock Division Control
000 = f/16
001 = f/12
010 = f/8
011 = f/6
100 = f/4
101 = f/3
110 = f/2
111 = f
2
CLKBX2
0 (normal)
MCLKB Multiplier Control
0 = Normal
1 = Multiply by 2
1
CLKAX2
0 (Off)
MCLKA Multiplier Control
0 = Normal
1 = Multiply by 2
0
CLKMUX
0 (MCLKA)
External Clock Source Control
0 = Use MCLKA
1 = Use MCLKB
Register 44h controls clock division and muxing.
w
PP, Rev 3.3, November 2011
117
WM9713L
Pre-Production
REGISTER
ADDRESS
46h
BIT
15:12
LABEL
N[3:0]
DEFAULT
0000 (div by 1)
DESCRIPTION
REFER TO
PLL Mode
PLL N Divide Control
0000 = Divide by 1
0001 = Divide by 1
0010 = Divide by 2
…
1111 = Divide by 15
11
LF
0 (normal)
PLL Low Frequency Input Control
1 = Low frequency mode (input clock < 8.192MHz)
0 = Normal mode
10
SDM
0 (disabled)
PLL SDM Enable Control
1 = Enable SDM (required for fractional N mode)
0 = Disable SDM
9
DIVSEL
0 (div by 1)
PLL Input Clock Division Control
0 = Divide by 1
1 = Divide according to DIVCTL
8
DIVCTL
0
PLL Input Clock Division Value Control
0 = Divide by 2
1 = Divide by 4
6:4
PGADDR
000
Pager Address
Pager address bits to access programming of
K[21:0] and SPLL[6:0]
3:0
PGDATA
0000
Pager Data
Pager data bits
Register 46h controls PLL clock generation.
w
PP, Rev 3.3, November 2011
118
WM9713L
Pre-Production
REGISTER
ADDRESS
4Ch
BIT
n
LABEL
GCn
DEFAULT
1 (input)
DESCRIPTION
REFER TO
GPIO and
Interrupt
Control
GPIO Pin Configuration Control
0 = Output
1 = Input (GC9-15 are always inputs)
4Eh
50h
n
n
GPn
GSn
1 (active high)
0 (not sticky)
GPIO Pin Polarity / Type
Input (GCn = 1)
Output (GCn = 0)
0 = Active low
0 = CMOS output
1 = Active high
1 = Open drain
GPIO Pin Sticky Control
0 = Not sticky
1 = Sticky
52h
n
GWn
0 (no wakeup)
GPIO Pin Wake-up Control
0 = No wake-up (no interrupts generated by GPIO)
1 = Wake-up (generate interrupts from GPIO)
54h
n
GIn
N/A
GPIO Pin Status
Read = Returns status of GPIO
Write = Writing 0 clears sticky bits
Bit definitions
for registers
4Ch to 54h
15
Controls Comparator 1 signal (virtual GPIO)
14
Controls Comparator 2 signal (virtual GPIO)
13
Controls Pen-Down Detector signal (virtual GPIO)
12
Controls ADA signal (virtual GPIO)
11
Controls Thermal sensor signal (virtual GPIO)
10
Controls Microphone short detect (virtual GPIO)
9
Controls Microphone insert detect (virtual GPIO)
8
Controls GPIO8 (pin 12)
7
Controls GPIO7 (pin 11)
6
Controls GPIO6 (pin 3)
5
Controls GPIO5 (pin 48)
4
Controls GPIO4 (pin 47)
3
Controls GPIO3 (pin 46)
2
Controls GPIO2 (pin 45)
1
Controls GPIO1 (pin 44)
Register 4Ch to 54h control the GPIO pins and virtual GPIO signals.
w
PP, Rev 3.3, November 2011
119
WM9713L
Pre-Production
REGISTER
ADDRESS
56h
BIT
8
LABEL
GE8
DEFAULT
1 (GPIO)
DESCRIPTION
REFER TO
GPIO8 (Pin 12) Function Control
0 = Pin 12 is not controlled by GPIO logic
1 = Pin 12 is controlled by GPIO logic
7
GE7
1 (GPIO)
GPIO and
Interrupt
Control
GPIO7 (Pin 11) Function Control
0 = Pin 11 is not controlled by GPIO logic
1 = Pin 11 is controlled by GPIO logic
6
GE6
1 (GPIO)
GPIO6 (Pin 3) Function Control
0 = Pin 3 is not controlled by GPIO logic
1 = Pin 3 is controlled by GPIO logic
5
GE5
1 (GPIO)
GPIO5 (Pin 48) Function Control
0 = Pin 48 is not controlled by GPIO logic
1 = Pin 48 is controlled by GPIO logic
4
GE4
1 (GPIO)
GPIO4 (Pin 47) Function Control
0 = Pin 47 is not controlled by GPIO logic
1 = Pin 47 is controlled by GPIO logic
3
GE3
1 (GPIO)
GPIO3 (Pin 46) Function Control
0 = Pin 46 is not controlled by GPIO logic
1 = Pin 46 is controlled by GPIO logic
2
GE2
1 (GPIO)
GPIO2 (Pin 45) Function Control
0 = Pin 45 is not controlled by GPIO logic
1 = Pin 45 is controlled by GPIO logic
Register 56h controls the use of GPIO pins for non-GPIO functions.
REGISTER
ADDRESS
58h
BIT
15:8
LABEL
PU
DEFAULT
01000000
DESCRIPTION
REFER TO
GPIO Pin Pull-Up Control
1 = Enables weak pull-up on GPIO pins
0 = No pull-up on GPIO pins
7:0
PD
00000000
GPIO and
Interrupt
Control
GPIO Pin Pull-Down Control
1 = Enables weak pull-down on GPIO pins
0 = No pull-down on GPIO pins
Register 58h controls GPIO pull-up/down.
w
PP, Rev 3.3, November 2011
120
WM9713L
Pre-Production
REGISTER
ADDRESS
5Ah
BIT
15:13
LABEL
DEFAULT
COMP2DEL
000 (no delay)
DESCRIPTION
REFER TO
Battery Alarm
Low Battery Alarm Delay Control
000 = No delay
13
001 = 2 AC-link frames
14
010 = 2 AC-link frames
15
011 = 2 AC-link frames
16
100 = 2 AC-link frames
17
101 = 2 AC-link frames
18
110 = 2 AC-link frames
19
111 = 2 AC-link frames
8
RSTDIS
0 (RESETB
enabled)
RESETB Pin Disable Control
00 (GPIO1)
Jack Detect Pin Input Control
GPIO Interrupt
and Control
0 = Pin 11 is RESETB
1 = Pin 11 is GPIO (RESETB function disabled)
7:6
JSEL
00 = GPIO1
01 = GPIO6
Jack Insertion
& AutoSwitching
10 = GPIO7
11 = GPIO8
5:4
HPMODE
00 (7Hz)
HPF Cut-Off Control
Audio ADCs
00 = 7Hz @ fs=48kHz
01 = 82Hz @ fs=16kHz
10 = 82Hz @ fs=8kHz
11 = 170Hz @ fs=8kHz
3:2
DIE REV
N/A
Device Revision (Read-Only)
N/A
00 = Rev.A
01 = Rev.B
10 = Rev.C
1
WAKEEN
0 (disabled)
GPIO Wake Up Control
0 = Disable wake-up
1 = Enable wake up
0
IRQ INV
0 (normal)
GPIO and
Interrupt
Control
IRQ Polarity Control
0 = Normal
1 = Inverted
Register 5Ah controls several additional functions.
w
PP, Rev 3.3, November 2011
121
WM9713L
REGISTER
ADDRESS
5Ch
Pre-Production
BIT
15
LABEL
AMUTE
DEFAULT
0
DESCRIPTION
REFER TO
Audio DACs,
Stereo DACs
DAC Automute Status (Read-Only)
0 = DAC not muted
1 = DAC auto-muted
14
C2REF
0 (AVDD/2)
Comparator 2 Reference Voltage Select
Battery Alarm
0 = AVDD/2
1 = WIPER/AUX4 (pin 12)
13:12
C2SRC
00 (power
down)
Comparator 2 Signal Source
00 = AVDD/2 when C2REF=1, else powered down
01 = COMP1/AUX1 (pin 29)
10 = COMP2/AUX2 (pin 30)
11 = Reserved
11
C1REF
0 (AVDD/2)
Comparator 1 Reference Voltage Select
0 = AVDD/2
1 = WIPER/AUX4 (pin 12)
10:9
C1SRC
00 (OFF)
Comparator 1 Signal Source
00 = AVDD/2 when C1REF=1, else powered down
01 = COMP1/AUX1 (pin 29)
10 = COMP2/AUX2 (pin 30)
11 = Reserved
7
AMEN
0 (OFF)
Stereo DAC
DAC Automute Control
0 = Disabled
1 = Enabled
6:5
VBIAS
00 (3.3V)
Power
Management
Analogue Bias Optimization Control
0X = Optimized for 3.3V
10 = Optimized for 2.5V
11 = Optimized for 1.8V
4
ADCO
0
(SDATAOUT)
Digital Audio
(S/PDIF)
Output
S/PDIF Data Source Control
0 = From SDATAOUT
1 = Output from audio ADC
3
HPF
0 (enabled)
Audio ADC
ADC HPF Disable Control
0 = HPF enabled
1 = HPF disabled
1:0
ASS
00 (slots 3, 4)
ADC Data Slot Mapping Control
Left Data
Right Data
00 =
Slot 3
Slot 4
01 =
Slot 7
Slot 8
10 =
Slot 6
Slot 9
11 =
Slot 10
Slot 11
Audio ADC,
ADC Slot
Mapping
Register 5Ch controls several additional functions.
w
PP, Rev 3.3, November 2011
122
WM9713L
Pre-Production
REGISTER
ADDRESS
60h
BIT
15:12
LABEL
ALCL
DEFAULT
1011 (-12dB)
DESCRIPTION
REFER TO
Audio ADC,
Automatic
Level Control
ALC Target Level Control
0000 = -28.5dBFS
… (1.5dB steps)
1111 = -6dBFS
11:8
HLD
0000 (0ms)
ALC Hold Time Control
0000 = 0ms
0001 = 2.67ms
… (time doubles with every step)
1111 = 43.691s
7:4
DCY
0011 (192ms)
ALC Decay Time Control
0000 = 24ms
… (time doubles with every step)
1010 to 1111 = 24.58s
3:0
ATK
0010 (24ms)
ALC Attack Time Control
0000 = 6ms
… (time doubles with every step)
1010 to 1111 = 6.14s
62h
15:14
ALCSEL
00 (disabled)
ALC Function Channel Control
00 = ALC disabled
01 = ALC on right channel only
10 = ALC or left channel only
11 = ALC on both left and right channels
13:11
MAXGAIN
111 (+30dB)
ALC PGA Gain Limit Control
000 = -12dB
… (6dB steps)
111 = +30dB
10:9
ZC
TIMEOUT
11 (slowest)
ALC Zero Cross Timeout Delay Control
14
00 = 2 x tBITCLK (1.33ms)
15
01 = 2 x tBITCLK (2.67ms)
16
10 = 2 x tBITCLK (5.33ms)
17
11 = 2 x tBITCLK (10.67ms)
7
NGAT
0 (disabled)
Noise Gate Enable Control
0 = Disabled
1 = Enabled
5
NGG
0 (hold gain)
Noise Gate Function Control
0 = Hold PGA gain at last value
1 = Mute ADC output
4:0
NGTH
00000 (76.5dB)
Noise Gate Threshold Control
00000 = -76.5dBFS
… (1.5dB steps)
11111 = -30dBFS
Registers 60h and 62h control the ALC and Noise Gate functions.
w
PP, Rev 3.3, November 2011
123
WM9713L
REGISTER
ADDRESS
64h
Pre-Production
BIT
15
LABEL
XSLE
DEFAULT
0 (DC)
DESCRIPTION
REFER TO
Auxiliary DAC
AUXDAC Input Select Control
0 = From AUXDACVAL[11:0] (for DC signals)
1 = From AC-Link (for AC signals)
14:12
AUXDAC
000 (Slot 5)
SLT
AUXDAC Input Control (XSLE=1)
000 = Slot 5, bits 8-19
001 = Slot 6, bits 8-19
010 = Slot 7, bits 8-19
011 = Slot 8, bits 8-19
100 = Slot 9, bits 8-19
101 = Slot 10, bits 8-19
110 = Slot 11, bits 8-19
111 = Reserved
11:0
AUXDAC
000h (min)
VAL
AUXDAC Input Control (XSLE=0)
000h = Minimum
FFFh = Full scale
Register 64h controls the input signal of the auxiliary DAC.
REGISTER
ADDRESS
74h
BIT
9
LABEL
POLL
DEFAULT
0
DESCRIPTION
REFER TO
Poll Measurement Control
Writing “1” initiates a measurement (when CTC is
not set)
8
CTC
0 (Polling)
Touchpanel
Interface
AUXADC Measurement Mode
0 = Polling mode
1 = Continuous mode (for DMA)
7
ADCSEL_
0 (disabled)
AUX4
AUX4 Measurement Enable Control
0 = Disable AUX4 measurement (pin 12)
1 = Enable AUX4 measurement (pin 12)
6
ADCSEL_
0 (disabled)
AUX3
AUX3 Measurement Enable Control
0 = Disable AUX3 measurement (SPKVDD/3)
1 = Enable AUX3 measurement (SPKVDD/3)
5
ADCSEL_
0 (disabled)
AUX2
AUX2 Measurement Enable Control
0 = Disable AUX2 measurement (pin 30)
1 = Enable AUX2 measurement (pin 30)
4
ADCSEL_
0 (disabled)
AUX1
AUX1 Measurement Enable Control
0 = Disable AUX1 measurement (pin 29)
1 = Enable AUX1 measurement (pin 29)
3
ADCSEL_
0 (disabled)
PRESSURE
Pressure Measurement Enable Control
0 = Disable pressure measurement
1 = Enable pressure measurement
2
ADCSEL_Y
0 (disabled)
Y Co-ordinate Measurement Enable Control
0 = Disable Y co-ordinate measurement
1 = Enable Y co-ordinate measurement
1
ADCSEL_X
0 (disabled)
X Co-ordinate Measurement Enable Control
0 = Disable X co-ordinate measurement
1 = Enable X co-ordinate measurement
0
COO
0 (single)
Co-ordinate Mode Control
0 = Single measurement
1 = Co-ordinate measurement
Register 74h controls the measurements for the touchpanel interface.
w
PP, Rev 3.3, November 2011
124
WM9713L
Pre-Production
REGISTER
ADDRESS
76h
BIT
9:8
7:4
LABEL
CR
DEL
DEFAULT
00 (93.75Hz)
0000 (20.8s)
DESCRIPTION
REFER TO
Continuous Mode Conversion Rate
DEL < 1111
DEL = 1111
00 = 93.75Hz
00 = 8kHz
01 = 120Hz
01 = 12kHz
10 = 153.75kHz
10 = 24kHz
11 = 187.5Hz
11 = 48kHz
Touchpanel
Interface
Touchpanel Settling Time Control
0000 = 1 AC-link frame (20.8µs)
0001 = 2 AC-link frames (41.7µs)
0010 = 4 AC-link frames (83.3µs)
0011 = 8 AC-link frames (167µs)
0100 = 16 AC-link frames (333µs)
0101 = 32 AC-link frames (667µs)
0110 = 48 AC-link frames (1ms)
0111 = 64 AC-link frames (1.33ms)
1000 = 96 AC-link frame (2ms)
1001 = 128 AC-link frames (2.67ms)
1010 = 160 AC-link frames (3.33ms)
1011 = 192 AC-link frames (4ms)
1100 = 224 AC-link frames (4.67ms)
1101 = 256 AC-link frames (5.33ms)
1110 = 288 AC-link frames (6ms)
1111 = No delay, switch matrix always on
3
SLEN
1 (enabled)
Slot Readback Enable Control
0 = Disabled (readback through register map only)
1 = Enabled (readback slot selected by SLT)
2:0
SLT
110 (slot 11)
AC’97 Slot for Touchpanel Data Control
000 = Slot 5
001 = Slot 6
010 = Slot 7
011 = Slot 8
100 = Slot 9
101 = Slot 10
110 = Slot 11
111 = Reserved
Register 76h controls the touchpanel interface measurement timing.
w
PP, Rev 3.3, November 2011
125
WM9713L
REGISTER
ADDRESS
78h
Pre-Production
BIT
15:14
LABEL
PRP
DEFAULT
00 (disabled)
DESCRIPTION
REFER TO
Touchpanel Digitiser Power State Control
00 = Disabled
Touchpanel
Interface
01 = Enable pen detect, wake-up on pen down
10 = Enable pen detect, no wake-up on pen down
11 = Pen detect and pen digitizer enabled
13
RPR
0 (AC-link)
Pen Detect Wake-up Mode Control
0 = Wake AC-link only
1 = Wake-up AC-link and WM9713
12
45W
0 (4-wire)
Touchpanel Type Control
0 = 4-wire
1 = 5-wire
11
PDEN
0 (always)
Touchpanel Measurement Pen Status Control
0 = Measure regardless of pen status
1 = Measure only when pen is down
10
PDPOL
0 (normal)
PENDOWN Polarity Control
0 = Normal
1 = Inverted
9
WAIT
0 (overwrite)
Touchpanel ADC Data Control
0 = Overwrite existing data in 7Ah with new data
1 = Retain existing data in 7Ah until it is read
8
PIL
0 (200A)
Pressure Measurement Current Control
0 = 200µA
1 = 400µA
7:6
MSK
00 (disabled)
Mask Input Control
00 = Disabled
01 = Static
10 = Edge-triggered
11 = Synchronous
5:0
RPU
000001
(64k)
Internal Pull-up Resistor Control
000000 = Reserved
000001 = 64kΩ/1 (most sensitive)
000010 = 64kΩ/2
000011 = 64kΩ/3
… (64kΩ/binary value of RPU)
111111 = 64kΩ/63 (least sensitive)
Register 78h controls the physical properties of the touchpanel interface.
w
PP, Rev 3.3, November 2011
126
WM9713L
Pre-Production
REGISTER
ADDRESS
7Ah
BIT
15
LABEL
PNDN
DEFAULT
0 (pen up)
read only
DESCRIPTION
REFER TO
Touchpanel
Interface
Pen Status (Read-only)
0 = Pen up
1 = Pen down
14:12
ADCSRC
000 (none)
Touchpanel ADC Source
000 = No measurement
001 = X co-ordinate measurement
010 = Y co-ordinate measurement
011 = Pressure measurement (4-wire only)
100 = COMP1/AUX1 measurement (pin 29)
101 = COMP2/AUX2 measurement (pin 30)
110 = AUX3 measurements (SPKVDD/3)
111 = WIPER/AUX4 measurement (pin 12)
11:0
ADCD
000h
Touchpanel ADC Data (Read-only)
Bit 0 = LSB
Bit 11 = MSB
Registers 7Ah is a read-only register which reports the touchpanel interface status and measurement results.
REGISTER
ADDRESS
BIT
LABEL
DEFAULT
DESCRIPTION
7Ch
15:8
F7:0
57h
ASCII character “W” for Wolfson
read-only
7:0
S7:0
4Dh
ASCII character “M”
7Eh
15:8
T7:0
4Ch
ASCII character “L”
read-only
7:0
REV7:0
13h
Device identifier
REFER TO
Intel’s AC’97
Component
Specification
, Revision
2.2, page 50
Register 7Ch and 7Eh are read-only registers that indicate to the driver that the CODEC is a WM9713L.
w
PP, Rev 3.3, November 2011
127
WM9713L
Pre-Production
APPLICATIONS INFORMATION
RECOMMENDED EXTERNAL COMPONENTS
Figure 36 Recommended External Component Diagram
w
PP, Rev 3.3, November 2011
128
WM9713L
Pre-Production
LINE OUTPUT
The headphone outputs, HPL and HPR, can be used as stereo line outputs. The speaker outputs,
SPKL and SPKR, can also be used as line outputs. Recommended external components are shown
below.
Figure 37 Recommended Circuit for Line Output
The DC blocking capacitors and the load resistance together determine the lower cut-off frequency,
fc. Assuming a 10 k load and C1, C2 = 10F:
fc = 1 / 2 (RL+R1) C1 = 1 / (2 x 10.1k x 1F) = 16 Hz
Increasing the capacitance lowers fc, improving the bass response. Smaller values of C1 and C2 will
diminish the bass response. The function of R1 and R2 is to protect the line outputs from damage
when used improperly.
AC-COUPLED HEADPHONE OUTPUT
The circuit diagram below shows how to connect a stereo headphone to the WM9713L.
Figure 38 Simple Headphone Output Circuit Diagram
The DC blocking capacitors C1 and C2 together with the load resistance determine the lower cut-off
frequency, fc. Increasing the capacitance lowers fc, improving the bass response. Smaller
capacitance values will diminish the bass response. For example, with a 16 load and C1 = 220F:
fc = 1 / 2 RLC1 = 1 / (2 x 16 x 220F) = 45 Hz
w
PP, Rev 3.3, November 2011
129
WM9713L
Pre-Production
DC COUPLED (CAPLESS) HEADPHONE OUTPUT
In the interest of saving board space and cost, it may be desirable to eliminate the 220F DC blocking
capacitors. This can be achieved by using OUT3 as a headphone pseudo-ground, as shown below.
Figure 39 Capless Headphone Output Circuit Diagram
As the OUT3 pin produces a DC voltage of AVDD/2, there is no DC offset between HPL/HPR and
OUT3, and therefore no DC blocking capacitors are required. However, this configuration has some
drawbacks:
The power consumption of the WM9713L is increased, due to the additional power consumed
in the OUT3 output buffer.
If the DC coupled output is connected to the line-in of a grounded piece of equipment, then
OUT3 becomes short-circuited. Although the built-in short circuit protection will prevent
any damage to the WM9713L, the audio signal will not be transmitted properly.
OUT3 cannot be used for another purpose
BTL LOUDSPEAKER OUTPUT
SPKL and SPKR can differentially drive a mono 8 loudspeaker as shown below.
Figure 40 Speaker Output Connection (INV = 1)
To drive out differentially one of the speaker outputs must be inverted using INV1 or INV2.
w
PP, Rev 3.3, November 2011
130
WM9713L
Pre-Production
COMBINED HEADSET / BTL EAR SPEAKER
In smartphone applications with a loudspeaker and separate ear speaker (receiver), a BTL ear
speaker can be connected at the OUT3 pin, as shown below.
Figure 41 Combined Headset / BTL Ear Speaker
The ear speaker and the headset play the same signal. Whenever the headset is plugged in, the
headphone outputs are enabled and OUT3 disabled. When the headset is not plugged in, OUT3 is
enabled (see “Jack Insertion and Auto-Switching”)
COMBINED HEADSET / SINGLE-ENDED EAR SPEAKER
Instead of a BTL ear speaker, a single-ended ear speaker can also be used, as shown below.
Figure 42 Combined Headset / Single-ended Ear Speaker
w
PP, Rev 3.3, November 2011
131
WM9713L
Pre-Production
JACK INSERT DETECTION
The circuit diagram below shows how to detect when a headphone or headset has been plugged into
the headphone socket. It generates an interrupt, instructing the controller to enable HPL and HPR
and disable OUT3.
Figure 43 Jack Insert Detection Circuit
The circuit requires a headphone socket with a switch that closes on insertion (for using sockets with
a switch that opens on insertion, please refer to Application Note WAN0182). It detects both
headphones and phone headsets. Any GPIO pin can be used, provided that it is configured as an
input.
HOOKSWITCH DETECTION
Alternatively a headphone socket with a switch that opens on insertion can be used. For this mode of
operation the GPIO input must be inverted.
The circuit diagram below shows how to detect when the “hookswitch” of a phone headset is pressed
(pressing the hookswitch is equivalent to lifting the receiver in a stationary telephone).
Figure 44 Hookswitch Detection Circuit
The circuit uses a GPIO pin as a sense input. The impedance of the microphone and the resistor in
the MICBIAS path must be such that the potential at the GPIO pin is above 0.7DBVDD when the
hookswitch is open, and below 0.3DBVDD when it is closed.
w
PP, Rev 3.3, November 2011
132
WM9713L
Pre-Production
TYPICAL OUTPUT CONFIGURATIONS
The WM9713L has three outputs capable of driving loads down to 16 (headphone / line drivers) –
HPL, HPR and MONO - and four outputs capable of driving loads down to 8 (loudspeaker / line
drivers) – SPKL, SPKR, OUT3 and OUT4. The combination of output drivers, mixers and mixer
inverters means that many output configurations can be supported. Below are some examples of
typical output configurations for smartphone applications.
STEREO SPEAKER
Figure 45 shows a typical output configuration for stereo speakers with headphones, ear speaker and
hands-free operation. The table shows suggested mixer outputs to select for each output PGA for a
given operating scenario. (Note the inverted mixer outputs can be achieved using the mixer output
inverters INV1 and INV2).
Figure 45 Stereo Speaker Output Configuration
w
PP, Rev 3.3, November 2011
133
WM9713L
Pre-Production
MONO SPEAKER
Figure 46 shows a typical output configuration for mono speaker with headphones, ear speaker and
hands-free operation. The table shows suggested mixer outputs to select for each output PGA for a
given operating scenario. (Note the inverted mixer outputs can be achieved using the mixer output
inverters INV1 and INV2).
Figure 46 Mono Speaker Output Configuration
w
PP, Rev 3.3, November 2011
134
WM9713L
Pre-Production
WM9713L MONO SPEAKER
Figure 47 shows a typical output configuration compatible with the WM9712 for mono speaker with
headphones, ear speaker and hands-free operation. The table shows suggested mixer outputs to
select for each output PGA for a given operating scenario. (Note the inverted mixer outputs can be
achieved using the mixer output inverters INV1 and INV2).
When using this configuration note that AVDD, HPVDD and SPKVDD must all be at the same voltage
to achieve the best performance.
Figure 47 WM9713L Mono Speaker Configuration
w
PP, Rev 3.3, November 2011
135
WM9713L
Pre-Production
PACKAGE DIMENSIONS
DM103.A
FL: 48 PIN QFN PLASTIC PACKAGE 7 X 7 X 0.9 mm BODY, 0.50 mm LEAD PITCH
D2
SEE DETAIL 1
D
D2/2
48
37
L
36
INDEX AREA
(D/2 X E/2)
1
EXPOSED
GROUND 6
PADDLE
E2/2
E2
E
SEE DETAIL 2
12
25
24
13
e
aaa C
2X
b
2X
BOTTOM VIEW
aaa C
TOP VIEW
ccc C
(A3)
A
0.08 C
SEATING PLANE
SIDE VIEW
A1
DETAIL 1
DETAIL 2
DETAIL 3
Datum
W
45°
T
(A3)
b
Exposed lead
EXPOSED
GROUND
PADDLE
Terminal
Tip
e/2
0.30mm
G
H
1
C
e
Half etch tie bar
DETAIL 3
Symbols
A
A1
A3
b
D
D2
E
E2
e
G
H
L
T
W
aaa
bbb
ccc
REF
Dimensions (mm)
NOM
MAX
0.90
1.00
0.05
0.02
0.20 REF
0.18
0.25
0.30
7.00 BSC
5.55
5.65
5.75
7.00 BSC
5.55
5.65
5.75
0.5 BSC
0.20
0.10
0.50
0.30
0.4
0.103
0.15
Tolerances of Form and Position
0.15
0.10
0.10
MIN
0.80
0
NOTE
1
JEDEC, MO-220, VARIATION VKKD-4
NOTES:
1. DIMENSION b APPLIED TO METALLIZED TERMINAL AND IS MEASURED BETWEEN 0.15 mm AND 0.30 mm FROM TERMINAL TIP.
2. ALL DIMENSIONS ARE IN MILLIMETRES
3. THE TERMINAL #1 IDENTIFIER AND TERMINAL NUMBERING CONVENTION SHALL CONFORM TO JESD 95-1 SPP-002.
4. COPLANARITY APPLIES TO THE EXPOSED HEAT SINK SLUG AS WELL AS THE TERMINALS.
5. THIS DRAWING IS SUBJECT TO CHANGE WITHOUT NOTICE.
6. REFER TO APPLICATION NOTE WAN_0118 FOR FURTHER INFORMATION REGARDING PCB FOOTPRINTS AND QFN PACKAGE SOLDERING.
w
PP, Rev 3.3, November 2011
136
Pre-Production
WM9713L
IMPORTANT NOTICE
Wolfson Microelectronics plc (“Wolfson”) products and services are sold subject to Wolfson’s terms and conditions of sale,
delivery and payment supplied at the time of order acknowledgement.
Wolfson warrants performance of its products to the specifications in effect at the date of shipment. Wolfson reserves the
right to make changes to its products and specifications or to discontinue any product or service without notice. Customers
should therefore obtain the latest version of relevant information from Wolfson to verify that the information is current.
Testing and other quality control techniques are utilised to the extent Wolfson deems necessary to support its warranty.
Specific testing of all parameters of each device is not necessarily performed unless required by law or regulation.
In order to minimise risks associated with customer applications, the customer must use adequate design and operating
safeguards to minimise inherent or procedural hazards. Wolfson is not liable for applications assistance or customer
product design. The customer is solely responsible for its selection and use of Wolfson products. Wolfson is not liable for
such selection or use nor for use of any circuitry other than circuitry entirely embodied in a Wolfson product.
Wolfson’s products are not intended for use in life support systems, appliances, nuclear systems or systems where
malfunction can reasonably be expected to result in personal injury, death or severe property or environmental damage.
Any use of products by the customer for such purposes is at the customer’s own risk.
Wolfson does not grant any licence (express or implied) under any patent right, copyright, mask work right or other
intellectual property right of Wolfson covering or relating to any combination, machine, or process in which its products or
services might be or are used. Any provision or publication of any third party’s products or services does not constitute
Wolfson’s approval, licence, warranty or endorsement thereof. Any third party trade marks contained in this document
belong to the respective third party owner.
Reproduction of information from Wolfson datasheets is permissible only if reproduction is without alteration and is
accompanied by all associated copyright, proprietary and other notices (including this notice) and conditions. Wolfson is
not liable for any unauthorised alteration of such information or for any reliance placed thereon.
Any representations made, warranties given, and/or liabilities accepted by any person which differ from those contained in
this datasheet or in Wolfson’s standard terms and conditions of sale, delivery and payment are made, given and/or
accepted at that person’s own risk. Wolfson is not liable for any such representations, warranties or liabilities or for any
reliance placed thereon by any person.
ADDRESS:
Wolfson Microelectronics plc
Westfield House
26 Westfield Road
Edinburgh
EH11 2QB
United Kingdom
Tel :: +44 (0)131 272 7000
Fax :: +44 (0)131 272 7001
Email :: [email protected]
w
PP, Rev 3.3, November 2011
137
WM9713L
Pre-Production
REVISION HISTORY
DATE
REV
ORIGINATOR
CHANGES
13/10/2008
3.3
BK
Corrected pin numbers for GPIO6 and GPIO8
114
3.3
BK
Added note with power-down sequence for VXDAC (see CE000296)
42
24/12/2009
3.3
BK
Added AUXDAC THD/SNR min/typ specs
03/08/2010
3.3
SS
Made changes to ‘Thermal Sensor’ section and Table 40 to correct and clarify.
60
Added note in Table 62 ‘GPIO Control’ to exclude Thermal Sensor from polarity
description and refer to Table 40 ‘Thermal Shutdown Control’.
86
30/08/2010
13/10/11
3.3
JMacD
Order codes updated from WM9713LGEFL/RV and WM9713LGEFL/RV to
WM9713CLGEFL/RV and WM9713CLGEFL/RV to reflect change to copper
wire bonding
4
13/10/11
3.3
JMacD
Package Diagram changed to DM103.A
136
w
PP, Rev 3.3, November 2011
138