INCH-POUND MIL-PRF-55681/4H 25 March 2015 SUPERSEDING MIL-PRF-55681/4G 10 September 2010 PERFORMANCE SPECIFICATION SHEET CAPACITOR, CHIP, MULTIPLE LAYER, FIXED, CERAMIC DIELECTRIC, ESTABLISHED RELIABILITY AND NON-ESTABLISHED RELIABILITY, STYLES CDR11, CDR12, CDR13, AND CDR14 (HIGH FREQUENCY) This specification sheet is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification and MIL-PRF-55681. Inches .005 .010 .015 .020 .025 .030 .035 .055 .057 .102 .110 mm 0.13 0.25 0.38 0.51 0.64 0.76 0.89 1.40 1.45 2.59 2.79 Dimensions Style CDR11 CDR12 CDR13 CDR14 L .055 ±.015 .055 ±.025 .110 ±.020 .110 -.020, +.035 W .055 ±.015 .055 ±.015 .110 ±.020 .110 ±.020 T Min Max .020 .020 .030 .030 .057 .057 .102 .102 Y .010 -.005 +.010 .010 -.005 +.010 .015 ±.010 .015 ±.010 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. FIGURE 1. Dimensions and configuration. AMSC N/A FSC 5910 MIL-PRF-55681/4H REQUIREMENTS: Dimensions and configuration: See figure 1. Terminations: Styles CDR11 and CDR13: Termination finish M or N. Styles CDR12 and CDR14: Termination finish S, U, W, Y, or Z. Solder, when applicable, shall have a maximum melting point of +200°C. Inspection conditions: Solderability examination shall be in accordance with method 208 of MIL-STD-202. All other visual examinations shall be performed using a stereo microscope having a minimum magnification of 20 power. Capacitance: See table I and table II. Capacitance tolerance: See table I and table II. Rated voltage: See table I and table II. Product level: Non-established reliability: C; established reliability: M, P, R, or S. Operating temperature range: -55°C to +125°C. Dissipation factor: In accordance with MIL-PRF-55681. Insulation resistance: At +25°C ±5°C: 10 megohms, minimum (for 0.1 pF through 470 pF); 10 megohms, minimum (for 510 pF through 1,000 pF). 6 5 At +125°C ±5°C: 10 megohms, minimum (for 0.1 pF through 470 pF); 10 megohms, minimum (for 510 pF through 1,000 pF). 5 4 Equivalent series resistance: In accordance with MIL-PRF-55681. Series resonance: In accordance with MIL-PRF-55681. NOTE: These capacitors are intended for use in RF solid-state circuitry up to and including 25 gigahertz, and cannot be replaced in the field. 2 MIL-PRF-55681/4H TABLE I. Styles CDR11 and CDR12 capacitor characteristics. Part or Identifying (PIN) 1/ 2/ CDR1-B-0R1-B - CDR1-B-0R2-B - CDR1-B-0R3 - - - CDR1-B-0R4 - - - CDR1-B-0R5 - - - CDR1-B-0R6 - - - CDR1-B-0R7 - - - CDR1-B-0R8 - - - CDR1-B-0R9 - - - CDR1-B-1R0 - - - CDR1-B-1R1 - - - CDR1-B-1R2 - - - CDR1-B-1R3 - - - CDR1-B-1R4 - - - CDR1-B-1R5 - - - CDR1-B-1R6 - - - CDR1-B-1R7 - - - CDR1-B-1R8 - - - CDR1-B-1R9 - - - CDR1-B-2R0 - - - CDR1-B-2R1 - - - CDR1-B-2R2 - - - CDR1-B-2R4 - - - CDR1-B-2R7 - - - CDR1-B-3R0 - - - CDR1-B-3R3 - - - CDR1-B-3R6 - - - CDR1-B-3R9 - - - CDR1-B-4R3 - - - CDR1-B-4R7 - - - CDR1-B-5R1 - - - CDR1-B-5R6 - - - CDR1-B-6R2 - - - CDR1-B-6R8 - - - CDR1-B-7R5 - - - CDR1-B-8R2 - - - CDR1-B-9R1 - - - CDR1-B-100 - - - CDR1-B-110 - - - CDR1-B-120 - - - CDR1-B-130 - - - CDR1-B-150 - - - CDR1-B-160 - - - CDR1-B-180 - - - CDR1-B-200 - - - CDR1-B-220 - - - CDR1-B-240 - - - CDR1-B-270 - - - - Capacitance (pF) 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2 2.1 2.2 2.4 2.7 3 3.3 3.6 3.9 4.3 4.7 5.1 5.6 6.2 6.8 7.5 8.2 9.1 10 11 12 13 15 16 18 20 22 24 27 Capacitance tolerance B B B, C B, C B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, J, K, M B, C, J, K, M B, C, J, K, M B, C, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M See footnotes at end of table. 3 Rated temperature and voltage temperature limits BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP Rated voltage (V dc) 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 MIL-PRF-55681/4H TABLE I. Styles CDR11 and CDR12 capacitor characteristics - Continued. PIN 1/ 2/ CDR1-B-300 - - - CDR1-B-330 - - - CDR1-B-360 - - - CDR1-B-390 - - - CDR1-B-430 - - - CDR1-B-470 - - - CDR1-B-510 - - - CDR1-B-560 - - - CDR1-B-620 - - - CDR1-B-680 - - - CDR1-B-750 - - - CDR1-B-820 - - - CDR1-B-910 - - - CDR1-B-101 - - - CDR1-BP111 - - - CDR1-BP121 - - - CDR1-BP131 - - - CDR1-BP151 - - - CDR1-BP161 - - - CDR1-BP181 - - - CDR1-BP201 - - - CDR1-BP221 - - - CDR1-BP241 - - - CDR1-BP271 - - - CDR1-BP301 - - - CDR1-BP331 - - - CDR1-BP361 - - - CDR1-BP391 - - - CDR1-BP431 - - - CDR1-BP471 - - - CDR1-BP511 - - - CDR1-BP561 - - - CDR1-BP621 - - - CDR1-BP681 - - - CDR1-BP751 - - - CDR1-BP821 - - - CDR1-BP911 - - - CDR1-BP102 - - - - Capacitance (pF) 30 33 36 39 43 47 51 56 62 68 75 82 91 100 110 120 130 150 160 180 200 220 240 270 300 330 360 390 430 470 510 560 620 680 750 820 910 1,000 Capacitance tolerance F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M Rated temperature and voltage temperature limits BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BP BP BP BP BP BP BP BP BP BP BP BP BP BP BP BP BP BP BP BP BP BP BP BP Rated voltage (V dc) 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 150 50, 100 50, 100 50, 100 50, 100 50, 100 50, 100 50, 100 50, 100 50, 100 50, 100 50, 100 50, 100 50, 100 50, 100 50, 100 50, 100 50, 100 50, 100 50, 100 50, 100 50, 100 50, 100 50, 100 50, 100 1/ Complete PIN shall include additional symbols to indicate style, voltage-temperature limits (where applicable), rated voltage, capacitance tolerance (where applicable), termination finish ("M" or "N" for style CDR11, and "S", "U", "W", "Y" or "Z" for style CDR12), and product level. 2/ All capacitors with the 150 volt rating (rated voltage code letter "K") are substitutable, with acquiring agency approval, for the same capacitors which had the 50 volt rating (rated voltage code letter "A") in previous revisions of this document. 4 MIL-PRF-55681/4H TABLE II. Styles CDR13 and CDR14 capacitor characteristics. PIN 1/ Capacitance (pF) Capacitance tolerance 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2 2.1 2.2 2.4 2.7 3 3.3 3.6 3.9 4.3 4.7 5.1 5.6 6.2 6.8 7.5 8.2 9.1 10 11 12 13 15 16 18 20 22 24 27 30 B B B, C B, C B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, D B, C, J, K, M B, C, J, K, M B, C, J, K, M B, C, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M CDR1-B-0R1-B - CDR1-B-0R2-B - CDR1-B-0R3 - - - CDR1-B-0R4 - - - CDR1-B-0R5 - - - CDR1-B-0R6 - - - CDR1-B-0R7 - - - CDR1-B-0R8 - - - CDR1-B-0R9 - - - CDR1-B-1R0 - - - CDR1-B-1R1 - - - CDR1-B-1R2 - - - CDR1-B-1R3 - - - CDR1-B-1R4 - - - CDR1-B-1R5 - - - CDR1-B-1R6 - - - CDR1-B-1R7 - - - CDR1-B-1R8 - - - CDR1-B-1R9 - - - CDR1-B-2R0 - - - CDR1-B-2R1 - - - CDR1-B-2R2 - - - CDR1-B-2R4 - - - CDR1-B-2R7 - - - CDR1-B-3R0 - - - CDR1-B-3R3 - - - CDR1-B-3R6 - - - CDR1-B-3R9 - - - CDR1-B-4R3 - - - CDR1-B-4R7 - - - CDR1-B-5R1 - - - CDR1-B-5R6 - - - CDR1-B-6R2 - - - CDR1-B-6R8 - - - CDR1-B-7R5 - - - CDR1-B-8R2 - - - CDR1-B-9R1 - - - CDR1-B-100 - - - CDR1-B-110 - - - CDR1-B-120 - - - CDR1-B-130 - - - CDR1-B-150 - - - CDR1-B-160 - - - CDR1-B-180 - - - CDR1-B-200 - - - CDR1-B-220 - - - CDR1-B-240 - - - CDR1-B-270 - - - CDR1-B-300 - - - See footnote at end of table. 5 Rated temperature and voltage temperature limits BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP Rated voltage (V dc) 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 MIL-PRF-55681/4H TABLE II. Styles CDR13 and CDR14 capacitor characteristics - Continued. PIN 1/ Capacitance (pF) Capacitance tolerance CDR1-B-330 - - - CDR1-B-360 - - - CDR1-B-390 - - - CDR1-B-430 - - - CDR1-B-470 - - - CDR1-B-510 - - - CDR1-B-560 - - - CDR1-B-620 - - - CDR1-B-680 - - - CDR1-B-750 - - - CDR1-B-820 - - - CDR1-B-910 - - - CDR1-B-101 - - - CDR1-B-111 - - - CDR1-B-121 - - - CDR1-B-131 - - - CDR1-B-151 - - - CDR1-B-161 - - - CDR1-B-181 - - - CDR1-B-201 - - - CDR1-B-221C - - CDR1-B-241C - - CDR1-B-271C - - CDR1-B-301C - - CDR1-B-331C - - CDR1-B-361C - - CDR1-B-391C - - CDR1-B-431C - - CDR1-B-471C - - CDR1-B-511B - - CDR1-B-561B - - CDR1-B-621B - - CDR1-B-681A - - CDR1-B-751A - - CDR1-B-821A - - CDR1-B-911A - - CDR1-B-102A - - CDR1-BP112A - - CDR1-BP122A - - CDR1-BP132A - - CDR1-BP152A - - CDR1-BP162A - - CDR1-BP182A - - CDR1-BP202A - - CDR1-BP222A - - CDR1-BP242A - - CDR1-BP272A - - CDR1-BP302A - - CDR1-BP332A - - - 33 36 39 43 47 51 56 62 68 75 82 91 100 110 120 130 150 160 180 200 220 240 270 300 330 360 390 430 470 510 560 620 680 750 820 910 1,000 1,100 1,200 1,300 1,500 1,600 1,800 2,000 2,200 2,400 2,700 3,000 3,300 F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M See footnote at end of table. 6 Rated temperature and voltage temperature limits BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BG, BP BP BP BP BP BP BP BP BP BP BP BP BP Rated voltage (V dc) 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 500 200, 300 200, 300 200, 300 200, 300 200, 300 200, 300 200, 300 200 200 200 200 200 200 200 200 200 100 100 100 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 MIL-PRF-55681/4H TABLE II. Styles CDR13 and CDR14 capacitor characteristics - Continued. PIN 1/ Capacitance (pF) Capacitance tolerance CDR1-BP362A - - CDR1-BP392A - - CDR1-BP432A - - CDR1-BP472A - - CDR1-BP502A - - CDR1-BP512A - - - 3,600 3,900 4,300 4,700 5,000 5,100 F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M F, G, J, K, M Rated temperature and voltage temperature limits BP BP BP BP BP BP Rated voltage (V dc) 50 50 50 50 50 50 1/ Complete PIN shall include additional symbols to indicate style, voltage-temperature limits (where applicable), rated voltage (where applicable), capacitance tolerance (where applicable), termination finish ("M" or "N" for style CDR13, and "S", "U", "W", "Y" or "Z" for style CDR14), and product level. Changes from previous issue: The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents: In addition to MIL-PRF-55681, this document also references MIL-STD-202. Custodians: Army - CR Navy - EC Air Force - 85 DLA - CC Preparing activity: Army - CR Agent: DLA - CC Review activities: Navy - AS, MC, OS, SH Air Force - 19, 99 (Project 5910-2015-013) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using ASSIST Online database at https://assist.dla.mil. 7