RF High Output Power Amplifier QB-865

Part Number: QB-865
2 Watt Broadband Driver Amplifier
800 to 2200 MHz Class A Linear Design
Features
•
•
•
•
High Output Power: +33 dBm Typical
Flat Gain
Balanced Configuration
Excellent Intermodulation Performance
3rd Order Intercept: +48 dBm Typical
2nd Order Intercept: +65 dBm Typical
API Technologies’ model QB-865 is a single stage, high dynamic range driver amplifier with extended performance from 800 to
2200 MHz to cover major telecommunication bands. Using a high reliability GaAs MESFET technology in a balanced
configuration, the module is able to achieve 2W of output power at 1dB compression with exceptional linearity, gain flatness,
and VSWR at the In/Out ports across the entire frequency range. The discrete design is supplied in an aluminum package with
SMA-F connectors for the RF ports and a 9 pin D-Sub for DC power to facilitate system integration. Operating from a nominal
+12V power supply, the QB-865 draws approximately 650 mA with a small signal gain of 14 dB and a typical noise figure of 5.0
dB. Optional services include over temperature testing, environmental screening, and(or) alternate package configurations.
Technical Specifications (1)
Absolute Maximum Ratings
Parameter
Unit
Typical
25°C
Min/Max
25°C
Parameter
Specification
Frequency Range
MHz
800 – 2200
900 – 2200
DC Voltage
+13.0 Vdc
Small Signal Gain
dB
14.0
13.0 min.
RF Input Power (2)
+23 dBm
Gain Flatness
dB
+/- 0.25
+/- 0.60 max.
Reverse Isolation
dB
25
22 min.
Input VSWR
—
1.2 :1
1.5 :1 max.
Output VSWR
—
1.2 :1
1.5 :1 max.
Noise Figure
dB
5.0
6.0 max.
POUT @ 1dB Compression
dBm
+33
+32 min.
3rd Order Output IP
dBm
+48
+45 min.
2nd
dBm
+65
+55 min.
DC Voltage
Vdc
+12
+12
Operating DC Current
mA
650
800 max.
Order Output IP
Mechanical Specifications
Parameter
Package (non-hermetic)
Finish
RF In/Out Connectors
DC Interface
Cooling
Specification
Comments
API Dwg: 080-23135
6061-T6 Al Alloy
Clear Iridite
MIL-DTL-5541F, Class 3
Captivated SMA Female
2-Hole Flange Mount
9 Pin D-Sub (Female)
Standard Density
Adequate Heat Sink Required
Note 4
Operating Case
Temperature (3)
-40oC to +75oC
Storage Temperature
-55oC to +125oC
Notes:
1. Specification ratings are based on measurements
in a 50 ohm system with a DC supply voltage
tolerance of ± 2%.
2. With RF output port terminated into 50
ohms (Load VSWR ≤ 2.0 :1)
3. Maximum Operating Case Temperature is
defined as the baseplate temperature which,
if exceeded for extended periods, could
result in premature unit failure. This data is
provided for user reliability information.
This may or may not represent the
maximum temperature for electrical
parameter specifications.
Rev Date: 5/12/2014
© API Technologies Corp. Proprietary Information
Page # 1
|
www.apitech.com
|
micro.apitech.com
|
+1.888.553.7531
|
[email protected]
Part Number: QB-865
Outline Drawing
Pin Designations
Pin #
Signal
1
+12V
2
N/C
3
N/C
4
N/C
5
N/C
6
N/C
7
N/C
8
Ground
9
N/C
Rev Date: 5/12/2014
© API Technologies Corp. Proprietary Information
Page # 2
|
www.apitech.com
|
micro.apitech.com
|
+1.888.553.7531
|
[email protected]