BE57-106-4 Eclipse706

Eclipse® Model 706
High Performance
Guided Wave Radar
Level Transmitter
DESCRIPTION
The Eclipse® Model 706 High Performance Transmitter is a
loop-powered, 24 VDC level transmitter that is based
upon the proven and accepted technology of Guided
Wave Radar (GWR). Encompassing a number of significant engineering accomplishments, this leading edge level
transmitter is designed to provide measurement performance well beyond that of many of the more traditional
technologies.
Measures Level, Interface,
Volume and Flow
Utilizing “diode switching” technology, along with the
most comprehensive probe offering on the market, this
single transmitter can be used in a wide variety of applications ranging from very light hydrocarbons to waterbased media.
The innovative angled, dual compartment enclosure is
now a common sight in the industry. This enclosure, first
brought to the industry by Magnetrol® in 1998, is angled
to maximize ease of wiring, configuration, and viewing of
the versatile graphic LCD display.
One universal Model 706 transmitter can be used and
interchanged with all probe types, and offers enhanced
reliability as it is suitable for use in critical SIL 2 hardware
safety loops.
The ECLIPSE Model 706 supports both the FDT/DTM and
Enhanced DD (EDDL) standards, which allow viewing of
valuable configuration and diagnostic information such as
the echo curve in tools such as PACTware ™, AMS Device
Manager, and various HART ® Field Communicators.
APPLICATIONS
MEDIA: Liquids, solids, or slurries; hydrocarbons to waterbased media (Dielectric Constant εr = 1.2–100)
VESSELS: Most process or storage vessels up to rated
probe temperature and pressure.
Eclipse® Model 706 DTM
CONDITIONS: All level measurement and control applications including process conditions exhibiting visible
vapors, foam, surface agitation, bubbling or boiling, high
fill/empty rates, low level and varying dielectric media or
specific gravity.
FEATURES
• Multivariable, two-wire, 24 VDC loop-powered transmitter for level, interface, volume, or flow.
• Diode switching technology offers best-in-class signal
strength and signal-to-noise ratio (SNR) resulting
in enhanced capability in difficult low dielectric
applications.
• Level measurement not affected by changing media
characteristics.
• No need to move levels for calibration.
• Overfill Capable probes allow for “true level” measurement all the way up to the process seal, without
the need for special algorithms.
• 4-button keypad and graphic LCD display allow for
convenient viewing of configuration parameters and
echo curve.
• Proactive diagnostics advise not only what is wrong,
but also offer troubleshooting tips.
• Nine common tank shapes for volumetric output.
• 30-point custom strapping table for uncommonlyshaped tanks.
• Two standard flumes and four standard weirs of
various sizes for flow measurement.
• Generic flow equation for non-standard channels.
• 360° rotatable housing can be separated from probe
without depressurizing the vessel.
• Probe designs up to +450 °C/431 bar (+850 °F/
6250 psi).
• Saturated steam applications up to 207 bar (3000 psi),
+400 °C (+750 °F) when installed in side-mounted
chamber.
• Cryogenic applications down to -196 °C (-320 °F).
• Transmitter can be remote-mounted up to 3,6 m
(12 feet) away from the probe.
• FMEDA evaluation allows use in SIL 2 Loops
(full FMEDA report available).
• No moving parts.
• FOUNDATION fieldbus™ and Modbus digital outputs.
TECHNOLOGY
PRINCIPLE OF OPERATION
ECLIPSE Guided Wave Radar is based upon the technology
of TDR (Time Domain Reflectometry). TDR utilizes pulses
of electromagnetic energy transmitted down a wave guide
(probe). When a pulse reaches a surface that has a higher
dielectric constant than the air (εr = 1) in which it is traveling, a portion of the pulse is reflected. The transit time
of the pulse is then measured via high speed timing
circuitry that provides an accurate measure of the liquid
(or solids) level. The amplitude of the reflection depends
on the dielectric constant of the product. The higher the
dielectric constant, the larger is the reflection.
Initial
Initial
Pulse
Pulse
Reflected
Reflected
Pulse
Pulse
Air εr =
=1
Air
r 1
ε
Initial
Pulse
Reflected
Pulse
Air εr = 1
εr > 1,2
Liquid εrr >> 1,2
1.2
Liquid
ε
Transmitted
Pulse
Transmitted
Transmitted
Pulse
Pulse
Overall Liquid Level
Bulk Solid Level
INTERFACE MEASUREMENT
The ECLIPSE Model 706 is capable of measuring both an
upper liquid level and an interface liquid level. As only a
portion of the pulse is reflected from a low dielectric upper
surface, some of the transmitted energy continues down
the GWR probe through the upper liquid. The remaining
initial pulse is again reflected when it reaches the higher
dielectric lower liquid. It is required that the upper liquid
has a dielectric constant less than 10, and the lower liquid
has a dielectric constant greater than 15. A typical interface
application would be oil over water, with the upper layer
of oil being non-conductive (εr ≈ 2.0), and the lower layer
of water being very conductive (εr ≈ 80). The thickness of the
upper layer could be as small as 50 mm (2") while the maximum upper layer is limited to the length of the GWR probe.
2
Reference
signal
Air εr = 1
Upper level
signal
Low dielectric medium
(eg. oil, εr = 2)
Emulsion layer
Interface
level signal
high dielectric medium
(eg. water, εr = 80)
Time
Interface Level
SPECIAL
APPLICATIONS
EMULSION LAYERS
OVERFILL CAPABILITY
As emulsion layers, also called “rag layers” can decrease
the strength of the reflected signal in an interface application, GWR transmitters are typically recommended for
applications that have clean, distinct layers.
Although agencies like WHG or VLAREM certify Overfill
proof protection, defined as the tested, reliable operation
when the transmitter is used as overfill alarm, it is assumed in their analysis that the installation is designed in
such a way that the vessel or side mounted cage cannot
physically overfill.
However, the ECLIPSE Model 706, with its powerful
internal measurement algorithms, will tend to detect the
top of an emulsion layer. Contact the factory for application assistance regarding emulsion layers in your specific
application.
SATURATED STEAM APPLICATIONS
(Boilers, Feedwater Heaters, etc.)
As the temperature of a saturated steam application
increases, the dielectric constant of the steam vapor space
also increases. This increase in vapor space dielectric
causes a delay in the GWR signal propagation as it travels down the probe, causing the liquid level to appear
lower than actual.
The ECLIPSE Model 706 transmitter and Model 7yS Coaxial
Steam probe provide a unique solution to this application.
The effects of the changing steam conditions can be
compensated for by utilizing a mechanical steam target
placed inside and near the top of the Model 7yS coaxial
probe.
NOTE: The measurement error associated with this
propagation delay does depend on temperature and is a function of the square root
of the vapor space dielectric constant. For
example, with no compensation, a +230 °C
(+450 °F) application would show a level
error of about 5.5 %, while a +315 °C
(+600 °F) application would show an error
approaching 20 %!
However, there are practical applications where a GWR
probe can be completely flooded with level all the way up
to the process connection (face of the flange). Although
the affected areas are application dependent, typical GWR
probes have a transition zone (or possibly dead zone) at
the top of the probe where interacting signals can either
affect the linearity of the measurement or, more dramatically, result in a complete loss of signal.
While some manufacturers of GWR transmitters may use
special algorithms to “infer” level measurement when this
undesirable signal interaction occurs and the actual level signal is lost, the ECLIPSE Model 706 offers a unique solution
by utilizing a concept called Overfill Safe Operation.
An Overfill safe probe is defined by the fact that it has
a predictable and uniform characteristic impedance all the
way down the entire length of the waveguide (probe).
These probes allow the ECLIPSE Model 706 to measure
accurate levels up to the process flange without any nonmeasurable zone at the top of the GWR probe.
Overfill safe GWR probes are unique to ECLIPSE GWR,
and coaxial probes can be installed at any location on the
vessel. Overfill safe probes are offered in a variety of
Coaxial and Caged designs.
Knowing exactly where the target is located at room temperature, and then continuously monitoring its apparent
location, the vapor space dielectric can be back-calculated.
Knowing the vapor space dielectric, accurate compensation of the actual liquid level reading is accomplished.
This is a patented technique with two US Patents
(US 6642801 and US 6867729) issued for both the mechanical target concept and the associated software algorithm.
Contact the factory for additional information relating to
saturated steam applications.
3
PROBE
THREE
OVERVIEW
STYLES
OF
GWR
PROBES
With one basic ECLIPSE Model 706 transmitter that operates with all probes, choosing the proper Guided Wave
Radar (GWR) probe is the most important decision in the
application process. The probe configuration establishes
fundamental performance characteristics.
All ECLIPSE Model 706 probes can be described by three
basic configurations:
• Coaxial
Each of these probe configurations has specific strengths
and weaknesses. Although there can be overlap, and different probes can certainly be used in similar applications,
it is important to understand their basic differences so that
one can choose the probe type that will offer optimal
performance.
The descriptions below are facts relating to the physics of
GWR technology and are not specific to the ECLIPSE
Model 706.
• Twin flexible cable
• Single element (rigid rod or flexible cable)
COAXIAL PROBES
BASIC —FOR CLEAN LIQUIDS
The coaxial probe is the most efficient of all GWR probe
configurations and should be the first consideration in all
applications. Analogous to the efficiency of coaxial cable,
a coaxial probe allows almost unimpeded movement of
the high frequency pulses throughout its length.
The basic 22,5 mm (0.875") diameter coaxial GWR probe
is only recommended for use in clean applications or special applications such as saturated steam. Teflon®, PEEK,
or alumina spacers centering the inner rod within the
outer tube are located at 60 cm (24") intervals, resulting in
a perfect characteristic impedance along the entire length
of the probe.
The electromagnetic field that develops between the inner
rod and outer tube is completely contained and uniform
down the entire length of the probe. See Figure 1. This means
that the coaxial probe is immune to any proximity affects
from other objects in the vessel, and therefore, in essence,
it can be used anywhere that it can mechanically fit.
The efficiency and overall sensitivity of a coaxial configuration yields robust signal strength, even in extremely
low dielectric (εr ≥1.4) applications. The sensitivity of this
“closed” design, however, also makes it more susceptible
to measurement error in applications that can have coating and buildup.
All ECLIPSE Model 706 coaxial probes are Overfill Safe as
standard, by design.
Figure 1
Coaxial Probe
4
This probe is recommended in applications with viscosities
up to 500 cP (mPa.s) maximum.
ENLARGED—FOR DIFFICULT LIQUIDS
The standard Enlarged 45 mm (1.75") or 49 mm (1.93”)
diameter coaxial GWR probes can be generally used for
most applications. They can be installed directly into the
tank as well as into bypass cages, stillwells or bridles.
The robust construction reduces the number of spacers
required, allowing the probe to be used in applications
where higher risk of buildup exists. To further reduce the
possibility of media buildup, the use of a single bottom
spacer is recommended up to probe lengths of 2.54 m
(100"). The overall sensitivity and performance of an enlarged coaxial GWR probe is identical to a standard coaxial GWR probe, but it offers the very important advantage
that it can be used in applications with viscosities up to
2,000 cP (mPa.s).
PROBE
THREE
OVERVIEW
STYLES
OF
CONTINUED
GWR
PROBES
OPTIONAL FLUSHING
CONNECTION
The maintenance of coaxial GWR probes in applications
suffering from buildup or crystallization can be significantly improved by using an optional flushing connection.
This flushing connection is a metal extension with a port
welded above the process connection. The port allows
the user to purge the inside of the coaxial GWR probe
during routine maintenance.
Note: The best approach to eliminate the effects of
condensation or crystallization is to install
adequate insulation or heat tracing (steam or
electrical). A flushing connection is no substitute for proper maintenance, but will help
to reduce the frequency of the intervention.
Flushing Port
Shown Plugged
(1⁄4” NPT-F)
CAGED—FOR DIRTY LIQUIDS
Unique to MAGNETROL, the Caged GWR probe is a single
rod probe which uses an existing or new cage, bridle, or
stillwell as the second conductor to re-create the same signal propagation of a coaxial GWR probe. Caged GWR
probes are designed for 2" (DN50), 3" (DN80) or 4"
(DN100) diameter metal chambers, and utilize a specially
designed impedance matching section that results in the
same overall characteristic impedance of a coaxial style
GWR probe.
Caged GWR probes offer the same sensitivity and performance as coaxial GWR probes, but the single conductor
design allows it to be used in applications with viscosities
up to 10,000 cP (mPa.s).
OPTIONAL ANNUNCIATOR
FITTING
High Pressure and High Temperature High Pressure
ECLIPSE Model 706 probes containing a glass ceramic
alloy process seal (Models 7yD, P, J, L, M and N) are available with an optional annunciator fitting. The use of this
fitting complies with the Dual Seal requirements of
ANSI/ISA-12.27.01-2011, titled “Requirements for Process
Sealing between Electrical Systems and Flammable or
Combustible Process Fluids,” which require the incorporation of a method that indicates or annunciates a primary
seal failure (e.g., visible leakage, an audible whistle, or
other means of monitoring).
5
PROBE
THREE
OVERVIEW
STYLES
OF
CONTINUED
GWR
PROBES
TWIN CABLE FLEXIBLE PROBES
The relationship of the Twin Cable probe design to a
coaxial probe design is similar to that of older, twin-lead,
antenna lead-in to modern, coaxial cable. 300-ohm twinlead cable simply does not have the efficiency of 75-ohm
coaxial cable, making the parallel conductor design less
sensitive than the concentric coaxial. See Figure 2. This translates into Twin Cable GWR probes having the ability to
measure dielectrics down to εr ≥1.7.
Figure 3 shows the single element design and how the
electromagnetic pulse effectively expands into a teardrop
shape as it propagates away from the top of the tank (the
inherent ground reference). This single element configuration (rod or cable) is the least efficient of the three probe
types, but can still operate with a with minimum dielectric detection of approximately εr > 1.7 in an open, nonmetallic vessel.
Heavy bridging of material between the cables across the
FEP coating can cause improper measurement and should
be avoided.
However, this dielectric constant performance improves
considerably (εr > 1.4) when the single rod probe is installed
in a metal cage/bridle, or mounted 50 –150 mm (2–6")
away from a metal tank wall. Because the design is
“open,” it exhibits two strong tendencies:
Figure 2 also shows that, although most of the electromagnetic field develops between the two cables, there is also
some peripheral energy that expands outward, making the
Twin Cable probe more sensitive to proximity effects of
objects located immediately around it. For that reason, it is
recommended to keep the active element of the Twin Cable
probe at least 25 mm (1") away from metal objects.
Figure 2
Twin Flexible Probe
• It is the most forgiving of coating and buildup. (The
PFA-insulated probe is the best choice for severe
buildup and coating).
• It is most affected by proximity issues.
It is important to note that a parallel metal wall INCREASES
the performance of a single rod probe while a singular,
metal object protruding out near the probe may be improperly detected as a liquid level.
These tendencies are application/installation dependent.
Therefore, by properly matching the single rod probe to a
cage/chamber, the ECLIPSE Model 706 broad offering of
caged probes combines the performance/sensitivity advantages of a coaxial probe and the viscosity immunity of
a single rod probe. The Caged Probes are Overfill Safe by
design, can be used in interface and other difficult, low
dielectric applications, and are unique to MAGNETROL
and the ECLIPSE Model 706.
Contact the factory for additional support and questions.
SINGLE ROD PROBES
Single element GWR probes act quite differently than both
coaxial and twin cable designs. With only one conductor
to work with, the pulses of energy develop between the
single rod probe and the mounting nut or flange. In other
words, the pulse propagates down and around the rod as
it references its ground at the top of the tank.
The energy and efficiency of the pulse are directly related
to how much metallic surface exists around it at the top of
the vessel. This metallic surface at the top of the probe is
called the “launch plate.” The larger the launch plate, the
more efficient the signal propagation down the probe.
6
Figure 3
Single Rod Probe
Launch Plate
PROBE
SELECTION
COAXIAL/CAGED GWR PROBE
GUIDE
TWIN CABLE GWR PROBE
signal propagation
SINGLE ROD/CABLE PROBE
signal propagation
signal propagation
La
end view
GWR
Description
Probe¿
7yT
7yP
7yD
7yS
7yG
7yL
7yJ
7yF
7yM
7yN
Installation
Dielectric
Range ¡¬
Temperature
Range √
Max.
Overfill
Vacuum ƒ
Pressure
Safe
Coaxial GWR Probes—Liquids
Standard Level/Interface Tank/Chamber ε 1.4–100 -40 to +200 °C
70 bar
r
Temperature
(-40 to +400 °F) (1000 psi)
High
-196 to +200 °C 431 bar
ε 1.4–100 (-320
Pressure Level/Interface Tank/Chamber r
to +400 °F) (6250 psi)
High Temp./ Level/Interface Tank/Chamber ε 1.4–100 -196 to +450 °C 431 bar
r
High Press.
(-320 to +850 °F) (6250 psi)
Steam
Saturated
-40
°C ≈ 207 bar
Tank/Chamber εr 10–100 (-40toto+400
Probe
Steam
+750 °F) (3000 psi)
Standard
Temperature Level/Interface
High
Pressure Level/Interface
High Temp./ Level/Interface
High Press.
Caged GWR Probes— Liquids
-40 to +200 °C
εr 1.4–100 (-40
Chamber
to +400 °F)
-196
+200 °C
εr 1.4–100 (-320 to
Chamber
to +400 °F)
-196 to +450 °C
εr 1.4–100 (-320
Chamber
to +850 °F)
Standard
Temperature
High
Pressure
High Temp./
High Press.
Single Rod Rigid GWR Probes—Liquids
-40 to +200 °C
70 bar
εr 1.7–100 (-40
Tank
to +400 °F) (1000 psi)
-196 to +200 °C 431 bar
εr 1.7–100 (-320
Tank
to +400 °F) (6250 psi)
-196
to
°C 431 bar
εr 1.7–100 (-320 to +450
Tank
+850 °F) (6250 psi)
Level
Level
Level
70 bar
(1000 psi)
431 bar
(6250 psi)
431 bar
(6250 psi)
Viscosity
cP (mPa.s)
Yes
Yes
500/2000
Full
Yes
500/2000
Full
Yes
500/2000
Full
No ∆
500
Yes
Yes
10000
Full
Yes
10000
Full
Yes
10000
Yes
No ➇
10000
Full
No ➇
10000
Full
No ➇
10000
Yes
No ➇
10000
Full
No ➇
10000
Full
No ➇
10000
7y6
Standard
Level
Temperature
High
Level
Pressure
High Temp./ Level/Interface
High Press
Single Cable Flexible GWR Probes—Liquids
-40 to +200 °C
70 bar
εr 1.7–100 (-40
Tank
to +400 °F) (1000 psi)
-196 to +200 °C 431 bar
εr 1.7–100 (-320
Tank
to +400 °F) (6250 psi)
-196
to
°C 431 bar
εr 1.4–100 (-320 to +450
Chamber
+850 °F) (6250 psi)
7y7
Standard
Temperature Level/Interface
Twin Cable Flexible GWR Probes— Liquids
-40 to +200 °C
70 bar
εr 1.7–100 (-40
Tank
to +400 °F) (1000 psi)
Yes
No ➇
1500
7y2
Bulk Solids
Probe
Level
Single Cable Flexible GWR Probes—Solids
-40 to +65 °C
εr 4–100 (-40
Tank
to +150 °F) Atmos.
No
No ➇
10000
7y5
Bulk Solids
Probe
Level
Twin Cable Flexible GWR Probes—Solids
-40 to +65 °C
εr 1.7–100 (-40
Tank
to +150 °F) Atmos.
No
No ➇
1500
7y1
7y3
¿
¡
¬
√
ƒ
Application
end view
2nd digit A=English, C=Metric
Minimum εr 1.2 with end of probe analysis enabled.
Single rod probes mounted directly into the vessel must be within 75–150 mm (3–6") of metal tank wall to obtain minimum dielectric of 1.4, otherwise r min = 1.7.
Depends on the probe spacer material. Refer to Model Selection for spacer options.
ECLIPSE probes containing o-rings can be used for vacuum (negative pressure) service, but only those probes with glass seals are hermetically sealed
to <10-8 cc/sec @ 1 atmosphere helium.
≈ When installed in side-mounted chamber.
∆ Consult factory for overfill applications
➇ Overfill capability can be achieved with software.
ε
7
TRANSMITTER
SPECIFICATIONS
FUNCTIONAL/PHYSICAL
System Design
Measurement Principle
Guided Wave Radar based on Time Domain Reflectometry (TDR)
Input
Measured Variable
Level, as determined by GWR time of flight
Span
15 cm to 30 m (6" to 100'); Model 7yS Probe 610 cm (20') max.
Output
Type
4 to 20 mA with HART: 3.8 mA to 20.5 mA useable (per NAMUR NE43)
FOUNDATION fieldbus™: H1 (ITK Ver. 6.1.1)
Modbus
Resolution
Analog:
Digital Display:
.003 mA
1 mm
Loop Resistance
591 ohms @ 24 VDC and 22 mA
Diagnostic Alarm
Selectable: 3.6 mA, 22 mA (meets requirements of NAMUR NE 43), or HOLD last output
Diagnostic Indication
Meets requirements of NAMUR NE107
Damping
Adjustable 0–10 seconds
User Interface
Keypad
4-button menu-driven data entry
Display
Graphic liquid crystal display
Digital Communication/Systems
HART Version 7—with Field Communicator, FOUNDATION fieldbus™, AMS, or FDT
DTM (PACTware™), EDDL
Menu Languages
Transmitter LCD: English, French, German, Spanish, Russian
HART DD: English, French, German, Spanish, Russian, Chinese, Portuguese
FOUNDATION fieldbus and Modbus Host System: English
Power (at transmitter terminals)
HART: General Purpose (Weather proof)/Intrinsically Safe/Explosion-proof:
16 to 36 VDC
11 VDC minimum under certain conditions (refer to I&O Manual BE57-606)
FOUNDATION fieldbus™: 9 to 17.5 VDC
FISCO ia / FNICO ic, Explosion Proof, General Purpose (Weather proof)
Modbus: 8 to 30 VDC
Explosion Proof, General Purpose, and Weatherproof
Housing
Material
Net/Gross Weight
IP67/die-cast aluminum A413 (<0.4 % copper); optional 316 stainless steel
Aluminum:
316 Stainless Steel:
2,0 kg (4.5 lbs.)
4,50 kg (10.0 lbs.)
Overall Dimensions
H 212 mm (8.34") x W 102 mm (4.03") x D 192 mm (7.56")
Cable Entry
1
SIL 2 Hardware (Safety Integrity Level)
Safe Failure Fraction = 93 % (HART only)
⁄2" NPT or M20
Functional Safety to SIL 2 as 1oo1 in accordance with IEC 61508
(Full FMEDA report available upon request)
8
TRANSMITTER
SPECIFICATIONS
CONTINUED
FUNCTIONAL/PHYSICAL
Environment
Operating Temperature
-40 to +80 °C (-40 to +175 °F); LCD viewable -20 to +70 °C (-5 to +160 °F)
Storage Temperature
-45 to +85 °C (-50 to +185 °F)
Humidity
0 to 99 %, non-condensing
Electromagnetic Compatibility
Meets CE requirement (EN 61326) and NAMUR NE 21
NOTE: Single Rod and Twin Cable probes must be used in metallic vessel
or stillwell to maintain CE noise immunity
Surge Protection
Meets CE EN 61326 (1000V)
Shock/Vibration
ANSI/ISA-S71.03 Class SA1 (Shock); ANSI/ISA-S71.03 Class VC2 (Vibration)
Performance
Reference Conditions ¿
Linearity ¡
with a 1,8 m (72") coaxial probe at +20 °C (+70 °F), in Auto Threshold Mode
Coaxial/Caged Probes:
Single Rod in Tanks/Twin Cable:
Accuracy ¬
Reflection from liquid, with dielectric constant in center of selected range,
<0.1 % of probe length or 2,5 mm (0.1"), whichever is greater
<0.3 % of probe length or 7,5 mm (0.3"), whichever is greater
Coaxial/Caged Probes:
±0.1 % of probe length or ±2,5 mm (0.1"), whichever is greater
Single Rod in Tanks/Twin Cable:
±0.5 % of probe length or ±13 mm (0.5"), whichever is greater
Interface Operation:
Coaxial/Caged probes: ±25 mm (1") for an interface thickness greater than
50 mm (2")
Twin Flexible probes: ±50 mm (2") for an interface thickness greater than
200 mm (8")
Resolution
±0.1 mm or 1"
Repeatability
<2,5 mm (0.1")
Hysteresis
<2,5 mm (0.1")
Response Time
Approximately 1 second
Initialization Time
Less than 10 seconds
Ambient Temperature Effect
Approx. ±0.02 % of probe length/°C (for probes greater than 2,5 m (8'))
Process Dielectric
<7,5 mm (0.3") within selected range
FOUNDATION fieldbus™
ITK Version
6.1.1
H1 Device Class
Link Master (LAS) —selectable ON/OFF
H1 Profile Class
31PS, 32L
Function Blocks
(8) Al, (3) Transducer, (1) Resource, (1) Arithmetic, (1) Input Selector,
(1) Signal Characterizer, (2) PID, (1) Integrator
Quiescent Current
15 mA
Execution Time
15 ms (40 ms PID Block)
Device Revision
01
DD Version
0x01
Modbus
Power Consumption
<0.5W
Signal Wiring
Two-wire half duplex RS-485 Modbus
Ground (common mode) Voltage
±7V
Bus Termination
Per EIA-485
¿ Specifications will degrade in Fixed Threshold mode.
¡ Linearity in top 46 cm (18") of Twin Cable and Single Rod probes in tanks will be application dependent.
¬ Accuracy may degrade when using manual or automatic compensation.
9
COAXIAL
PROBE
MATRIX
7yT
7yP
Description
Standard Temperature
High Pressure
Application
Level/Interface
Level/Interface
Installation
Tank/Chamber
Tank/Chamber
Overfill Safe
Yes
Yes
316/316L (1.4401/1.4404)
Hastelloy® C (2.4819)
Monel® (2.4360)
316/316L (1.4401/1.4404)
Hastelloy® C (2.4819)
Monel® (2.4360)
Materials — Probe
Teflon® TFE with Viton® o-rings ¿ Hermetic Glass Ceramic, Inconel
Process Seal
Spacers
Teflon® TFE
Teflon® TFE
316 SS: 45 mm (1.75")
Hastelloy: 49 mm (1.90")
Monel: 49 mm (1.90")
22,5 mm (0.87")
316 SS: 45 mm (1.75")
Hastelloy: 49 mm (1.90")
Monel: 49 mm (1.90")
22,5 mm (0.87")
Enlarged 2" NPT
(3⁄4" NPT or 1" BSP)
Various ANSI, EN1092, and
proprietary flanges
Enlarged 2" NPT
(3⁄4" NPT or 1" BSP)
Various ANSI, EN1092, and
proprietary flanges
Standard
Enlarged
30 to 610 cm (12 to 240")
9 m (30') max segmented
30 to 610 cm (12 to 240")
9 m (30') max segmented
Top
Bottom
εr = 1.4: 150 mm (6") ƒ,
εr = 80: 50 mm (2")
0 mm (0")
εr = 1.4: 150 mm (6") ƒ,
εr = 80: 50 mm (2")
Probe Outside Diameter
Enlarged
Basic
Process Connection
Threaded
Flanged
Available Probe Length
Transition Zones ¡
0 mm (0")
Process Temperature
-40 to +200 °C (-40° to +400 °F) -196 to +200 °C (-320° to +400 °F)
Max. Process Pressure ¬
70 bar @ +20 °C (1000 psi @ +70 °F) 431 bar @ +20 °C (6250 psi @ +70 °F)
Dielectric Range
Vacuum Service √
1.4 to 100 ≈
1.4 to 100 ≈
Negative Pressure,
but no hermetic seal
Full Vacuum
2000cP (mPa.s)
500cP (mPa.s)
2000cP (mPa.s)
500cP (mPa.s)
Filming
Filming
Viscosity
Enlarged
Basic
Media Coating
¿ Other o-ring materials available upon request.
¡ Transition zones (areas with reduced accuracy) are dielectric dependent. It is recommended to set the 0-100 %
measuring range outside of the transition zones.
¬ Refer to chart on page 16.
√ ECLIPSE probes containing o-rings can be used for vacuum (negative pressure) service, but only those probes with
glass seal are hermetically sealed to <10-8 cc/sec @ 1 atmosphere helium.
ƒ Can be reduced to 75 mm (3") when lower accuracy is acceptable.
≈ 1.2 minimum dielectric when end of probe analysis is enabled.
10
COAXIAL
PROBE
MATRIX
CONTINUED
7yD
7yS
Description
High Temp./High Pressure
Steam Probe
Application
Level/Interface
Saturated Steam
Installation
Tank/Chamber
Tank/Chamber
Overfill Safe
Yes
No ≈
Materials — Probe
316/316L (1.4401/1.4404)
Hastelloy® C (2.4819)
Monel® (2.4360)
316/316L (1.4401/1.4404)
Hastelloy® C (2.4819)
Process Seal
Hermetic Glass Ceramic,
Inconel
Hermetic Glass Ceramic,
PEEK HT, Inconel
PEEK HT/Ceramic
PEEK HT/Ceramic
316 SS: 45 mm (1.75")
Hastelloy: 49 mm (1.92")
Monel: 49 mm (1.92")
22,5 mm (0.87")
N/A
22,5 mm (0.87")
N/A
31,8 mm (1.25")
2" NPT or 2" BSP
Various ANSI, EN1092, and
proprietary flanges
⁄4" NPT or 1" BSP ∆
Various ANSI, EN1092, and
proprietary flanges
30 to 610 cm (12 to 240")
9 m (30') max segmented
60 to 610 cm (24 to 240")
N/A
Spacers
Probe Outside Diameter
Enlarged
Basic
HIgh-Temp Model 7YS
Process Connection
Threaded
Flanged
3
Available Probe Length
Standard
Enlarged
Transition Zones ¿
Top
Bottom
0 mm (0")
εr = 1.4: 150 mm (6") √,
εr = 80: 50 mm (2")
200 mm (8")
εr = 80: 50 mm (2")
Process Temperature
-196 to 450 °C (-320 to +850 °F) -50 to +400 °C (-58 to +750 °F) ➇
Max. Process Pressure ¡
431 bar @ +20°C (6250 psi @ +70 °F)
207 bar @ +20 °C (3000 psi @ +70 °F)
155 bar @ +345 °C (2250 psi @ +650 °F)
Dielectric Range
1.4 to 100 ƒ
10 to 100
Vacuum Service ¬
Full Vacuum
Full Vacuum
2000cP (mPa.s)
500cP (mPa.s)
N/A
500cP (mPa.s)
Filming
Filming
Viscosity
Enlarged
Basic
Media Coating
¿ Transition zones (areas with reduced accuracy) are dielectric dependent. It is recommended to set the 0-100 %
measuring range outside of the transition zones.
¡ Refer to chart on page 16.
¬ ECLIPSE probes containing o-rings can be used for vacuum (negative pressure) service, but only those probes with
glass seal are hermetically sealed to <10-8 cc/sec @ 1 atmosphere helium.
√ Can be reduced to 75 mm (3") when lower accuracy is acceptable.
ƒ 1.2 minimum dielectric when end of probe analysis is enabled.
≈ Consult factory for overfill applications.
∆ Not available with +345 °C (+650 °F) version of the 7yS probe.
➇ When installed in side-mounted chamber.
11
CAGED
PROBE
MATRIX
7yG
7yL
7yJ
Description
Standard Temperature
High Pressure
High Temp./High Pressure
Application
Level/Interface
Level/Interface
Level/Interface
Installation
Chamber
Chamber
Chamber
Yes
Yes
Yes
316/316L (1.4401/1.4404)
Hastelloy® C (2.4819)
Monel® (2.4360)
316/316L (1.4401/1.4404)
Hastelloy® C (2.4819)
Monel® (2.4360)
316/316L (1.4401/1.4404)
Hastelloy® C (2.4819)
Monel® (2.4360)
Overfill Safe ∆
Materials — Probe
Process Seal
Teflon® TFE with Viton® o-rings¿ Hermetic Glass Ceramic, Inconel Hermetic Glass Ceramic, Inconel
Spacers
PEEK
PEEK
PEEK HT/Celazole
Probe Outside Diameter
13 mm (.5") to 19 mm (.75")
13 mm (.5") to 19 mm (.75")
13 mm (.5") to 19 mm (.75")
2" Chamber
3" Chamber 19 mm (.75") to 29 mm (1.13") 19 mm (.75") to 29 mm (1.13") 19 mm (.75") to 29 mm (1.13")
4" Chamber 27 mm (1.05") to 38 mm (1.50") 27 mm (1.05") to 38 mm (1.50") 27 mm (1.05") to 38 mm (1.50")
Process Connection
Flanged
Various ANSI, EN1092, and
proprietary flanges
Various ANSI, EN1092, and
proprietary flanges
Various ANSI, EN1092, and
proprietary flanges
30 to 610 cm (12 to 240")
30 to 610 cm (12 to 240")
30 to 610 cm (12 to 240")
εr = 1.4: 150 mm (6") ƒ,
εr = 80: 50 mm (2")
0 mm (0")
εr = 1.4: 150 mm (6") ƒ,
εr = 80: 50 mm (2")
0 mm (0")
εr = 1.4: 150 mm (6") ƒ,
εr = 80: 50 mm (2")
-40 to +200 °C (-40 to +400 °F)
-196 to +200 °C (-320 to +400 °F)
-196 to +450 °C (-320 to +850 °F)
Available Probe Length
Transition Zones ¡
Top
Bottom
Process Temperature
Max. Process Pressure ¬
Dielectric Range ∆
Vacuum Service √
Viscosity
Media Coating
70 bar @ +20 °C (1000 psi @ +70 °F) 431 bar @ +20 °C (6250 psi @ +70 °F) 431 bar @ +20 °C (6250 psi @ +70 °F)
1.4 to 100 ≈
1.4 to 100 ≈
1.4 to 100 ≈
Negative Pressure,
but no hermetic seal
Full Vacuum
Full Vacuum
10,000cP (mPa.s)
10,000cP (mPa.s)
10,000cP (mPa.s)
Maximum Error 10 %
of coated length
(% Error is dependent on
dielectric and thickness)
Maximum Error 10 %
of coated length
(% Error is dependent on
dielectric and thickness)
Maximum Error 10 %
of coated length
(% Error is dependent on
dielectric and thickness)
¿ Other o-ring materials available upon request.
¡ Transition zones (areas with reduced accuracy) are dielectric dependent. It is recommended to set the 0-100 %
measuring range outside of the transition zones.
¬ Refer to chart on page 16.
√ ECLIPSE probes containing o-rings can be used for vacuum (negative pressure) service, but only those probes with
glass seal are hermetically sealed to <10-8 cc/sec @ 1 atmosphere helium.
ƒ Can be reduced to 75 mm (3") when lower accuracy is acceptable.
≈ 1.2 minimum dielectric when end of probe analysis is enabled.
∆ When installed in the proper chamber/cage/stilling well.
12
0 mm (0")
SINGLE
ROD
RIGID
PROBE
MATRIX
7yF
7yM
7yN
Description
Standard Temperature
High Pressure
High Temp./High Pressure
Application
Level
Level
Level
Installation
Tank
Tank
Tank
No
No
No
316/316L (1.4401/1.4404)
Hastelloy® C (2.4819)
Monel® (2.4360)
PFA Insulated 316/316L rod
316/316L (1.4401/1.4404)
Hastelloy® C (2.4819)
Monel® (2.4360)
316/316L (1.4401/1.4404)
Hastelloy® C (2.4819)
Monel® (2.4360)
Overfill Safe ∆
Materials — Probe
Process Seal
Teflon® TFE with Viton® o-rings¿ Hermetic Glass Ceramic, Inconel Hermetic Glass Ceramic, Inconel
Spacers
Probe Outside Diameter
None
None
PEEK HT/Celazole
Bare: 10 mm (0.38") rod
Coated: 16 mm (0.625") rod
Bare: 10 mm (0.38") rod
Bare: 13 mm (0.50") rod
1" or 2” (NPT or BSP)
Various ANSI, EN1092, and
proprietary flanges
1" or 2” (NPT or BSP)
Various ANSI, EN1092, and
proprietary flanges
2” (NPT or BSP)
Various ANSI, EN1092, and
proprietary flanges
60 to 732 cm (24" to 288")
610 cm (240") maximum
for PFA coated probes
60 to 732 cm (24" to 288")
60 to 732 cm (24" to 288")
εr = 1.4: 150 mm (6") ƒ,
εr = 80: 50 mm (2")
Application Dependent
εr = 1.4: 150 mm (6") ƒ,
εr = 80: 50 mm (2")
Application Dependent
εr = 1.4: 150 mm (6") ƒ,
εr = 80: 50 mm (2")
-40 to +200 °C (-40 to +400 °F)
-196 to +200 °C (-320 to +400 °F)
-196 to +450 °C (-320 to +850 °F)
Process Connection
Threaded
Flanged
Available Probe Length
Transition Zones ¡
Top
Bottom
Process Temperature
Max. Process Pressure ¬
Dielectric Range
Vacuum Service √
Viscosity
Media Coating
Application Dependent
70 bar @ +20 °C (1000 psi @ +70 °F) 431 bar @ +20 °C (6250 psi @ +70 °F) 431 bar @ +20 °C (6250 psi @ +70 °F)
1.7 to 100 ≈
1.7 to 100 ≈
1.7 to 100 ≈
Negative Pressure,
but no hermetic seal
Full Vacuum
Full Vacuum
10,000cP (mPa.s)
10,000cP (mPa.s)
10,000cP (mPa.s)
Maximum Error 10 %
of coated length
(% Error is dependent on
dielectric and thickness)
Maximum Error 10 %
of coated length
(% Error is dependent on
dielectric and thickness)
Maximum Error 10 %
of coated length
(% Error is dependent on
dielectric and thickness)
¿ Other o-ring materials available upon request.
¡ Transition zones (areas with reduced accuracy) are dielectric dependent. It is recommended to set the 0-100 %
measuring range outside of the transition zones.
¬ Refer to chart on page 16.
√ ECLIPSE probes containing o-rings can be used for vacuum (negative pressure) service, but only those probes with
glass seal are hermetically sealed to <10-8 cc/sec @ 1 atmosphere helium.
ƒ Can be reduced to 75 mm (3") when lower accuracy is acceptable.
≈ 1.2 minimum dielectric when end of probe analysis is enabled.
∆ Overfill capability can be achieved with software.
13
FLEXIBLE
PROBES
FOR
LIQUIDS
MATRIX
7y1
7y3
Description
Single Flexible
Standard Temperature
Single Flexible
High Pressure
Application
Level
Level
Installation
Tank
Tank
No
No
316 (1.4401)
(optional PFA coating)
316 (1.4401)
Teflon® TFE with Viton® o-rings¿
Hermetic Glass Ceramic
5 mm (0.19")
5 mm (0.19")
2" NPT or 2" BSP
Various ANSI, EN1092, and
proprietary flanges
2" NPT or 2" BSP
Various ANSI, EN1092, and
proprietary flanges
1 to 30 m (3 to 100')
1 to 30 m (3 to 100')
45 cm (18")
30 cm (12")
45 cm (18")
30 cm (12")
-40 to +200 °C (-40 to +400 °F)
-196 to +200 °C (-320 to +400 °F)
Overfill Safe ≈
Materials — Cable
Process Seal
Probe Outside Diameter
Process Connection
Threaded
Flanged
Available Probe Length
Transition Zones ¡
Top
Bottom
Process Temperature
Max. Process Pressure ¬
Dielectric Range ƒ
Vacuum Service √
Viscosity
Media Coating
70 bar @ +20°C (1000 psi @ +70 °F) 431 bar @ +20 °C (6250 psi @ +70 °F)
1.7 to 100
1.7 to 100
Negative Pressure,
but no hermetic seal
Full Vacuum
10,000 (mPa.s)
10,000 (mPa.s)
Maximum Error 10 %
of coated length
(% Error is dependent on
dielectric and thickness)
Maximum Error 10 %
of coated length
(% Error is dependent on
dielectric and thickness)
¿ Other o-ring materials available upon request.
¡ Transition zones (areas with reduced accuracy) are dielectric dependent. It is recommended to set the 0-100 %
measuring range outside of the transition zones.
¬ Refer to chart on page 16.
√ ECLIPSE probes containing o-rings can be used for vacuum (negative pressure) service, but only those probes with
glass seal are hermetically sealed to <10-8 cc/sec @ 1 atmosphere helium.
ƒ 1.2 minimum dielectric when end of probe analysis is enabled.
≈ Overfill capability can be achieved with software.
14
FLEXIBLE
PROBES
FOR
LIQUIDS
MATRIX
7y6
7y7
Description
Single Flexible
HTHP
Twin Flexible
Standard Temperature
Application
Level
Level/Interface
Installation
Tank/Chamber
Tank/Chamber
Overfill Safe
No
No
316 (1.4401)
316 SS (1.4401) Cables with FEP Webbing
Hermetic Glass Ceramic
Teflon® TFE with Viton® o-rings
5 mm (0.19")
(2) 6 mm (0.25")
2" NPT or 2" BSP
Various ANSI, EN, and
proprietary flanges
2" NPT or 2" BSP
Various ANSI, EN, and
proprietary flanges
1 to 30 m (3 to 100')
1 to 30 m (3 to 100')
45 cm (18")
30 cm (12")
45 cm (18")
30 cm (12")
-196 to +450 °C (-320 to +850 °F)
-40 to +200 °C (-40 to +400 °F)
Materials — Cable
Process Seal ¿
Cable Outside Diameter
CONTINUED
Process Connection
Threaded
Flanged
Available Probe Length
Transition Zones ¡
Top
Bottom
Process Temperature
Max. Process Pressure ¬
Dielectric Range ƒ
Vacuum Service √
Viscosity
Media Coating
431 bar @ +20 °C (6250 psi @ +70 °F) 70 bar @ +20 °C (1000 psi @ +70 °F)
1.7 to 100
1.7 to 100
Full Vacuum
Negative Pressure,
but no hermetic seal
10,000 (mPa.s)
1500 (mPa.s)
Maximum Error 10 %
of coated length
(% Error is dependent on
dielectric and thickness)
Maximum Error 10 %
of coated length
(% Error is dependent on
dielectric and thickness)
¿ Other o-ring materials available upon request.
¡ Transition zones (areas with reduced accuracy) are dielectric dependent. It is recommended to set the 0-100 %
measuring range outside of the transition zones.
¬ Refer to chart on page 16.
√ ECLIPSE probes containing o-rings can be used for vacuum (negative pressure) service, but only those probes with
glass seal are hermetically sealed to <10-8 cc/sec @ 1 atmosphere helium.
ƒ 1.2 minimum dielectric when end of probe analysis is enabled.
15
FLEXIBLE
PROBES
FOR
SOLIDS
MATRIX
7y2
7y5
Description
Single Flexible Standard Temp.
Twin Flexible Standard Temp.
Application
Level
Level
Installation
Tank
Tank
Overfill Safe
No
No
Pull Down Force
1360 Kg (3000 lbs.)
1360 Kg (3000 lbs)
Materials — Cable
316 (1.4401)
316 (1.4401)
Probe Outside Diameter
5 mm (0.19")
(2) 6 mm (0.25")
Process Connection
2" NPT or 2" BSP
2" NPT or 2" BSP
Threaded
Flanged Various ANSI, EN1092, and proprietary flanges Various ANSI, EN1092, and proprietary flanges
Available Probe Length
1 to 30 m (3 to 100')
1 to 30 m (3 to 100')
45 cm (18")
30 cm (12")
45 cm (18")
30 cm (12")
4 to 100
1.9 to 100
Negative Pressure, but no hermetic seal
Negative Pressure, but no hermetic seal
10,000 (mPa.s)
10,000 (mPa.s)
Transition Zones ¿
Top
Bottom
Dielectric Range ¡
Vacuum Service ¬
Viscosity
Max. Error 10 % of coated length
Max. Error 10 % of coated length
(% Error is dependent on dielectric & thickness) (% Error is dependent on dielectric & thickness)
Media Coating
¿ Transition zones (areas with reduced accuracy) are dielectric dependent. It is recommended to set the 0-100 % measuring range outside of the transition zones.
¡ 1.2 minimum dielectric when end of probe analysis is enabled.
¬ ECLIPSE probes containing o-rings can be used for vacuum (negative pressure) service, but only those probes with glass seal are hermetically sealed
(helium leak <10-8cc/sec @ 1 atmos.).
7yL, 7yM and 7yP
Temperature/Pressure Ratings
379
(5500)
345
(5000)
310
(4500)
316/316L SST
Hastelloy C276
Monel 400
241
(3500)
207
(3000)-15
(0)
40
(100)
95
(200)
150
(300)
Temperature °C (°F)
High Pressure Probes
Low Pressure
Temp.
SST
Hastelloy
Monel
-40 (-40)
6000
6250
20 (+70)
6000
6250
40 (+100)
6000
95 (+200)
200
(400)
379
5500
(5500)
345
5000
(5000)
310
4500
(4500)
276
4000
(4000)
241
3500
(3500)
95
(200)
200
(400)
315
(600)
425
(800)
540
(1000)
Temperature °C (°F)
7yF,
7yG,
7yT,
7y1,7y1,
7y4,7y7
7y7
7yF,
7yG,
7yT,
Low Pressure
All Materials
Temp.
SST
Hastelloy
Monel
All Materials
5000
750
315 (+600)
3760
5040
3940
—
5000
1000
345 (+650)
3680
4905
3940
—
6250
5000
1000
370 (+700)
3620
4730
3920
—
5160
6250
4380
650
400 (+750)
3560
4430
3880
—
150 (+300)
4660
6070
4080
400
425 (+800)
3520
4230
3820
—
200 (+400)
4280
5820
3940
270
450 (+850)
3480
4060
3145
—
260 (+500)
3980
5540
3940
—
16
316/316L SST
Hastelloy C276
Monel 400
414
6000
(6000)
207
3000
(3000)-15
(0)
260
(500)
High Pressure Probes
Maximum Pressure (PSI)
414
(6000)
276
(4000)
7yD, 7yJ, 7yN, 7y3 and 7y6
Temperature/Pressure Ratings
448
6500
(6500)
Maximum Pressure bar (psi)
Maximum Pressure bar (psi)
448
(6500)
NOTES:
• 7yS steam probes are rated to 155 bar (2250 psi) @ +345 °C (+650 °F)
• 7y3, 7y6 HTHP flexible probes:
Pressure is limited by the chamber
• 7y2, 7y5 bulk solids probes: 3,45 bar (50 psi) to +65 °C (+150 °F)
• High pressure probes with threaded fittings are rated as follows:
7yD, 7yN, 7yP and 7y3 probes with threaded fittings have 248 bar (3600 psi)
rating. 7yM probes with threaded fittings have 139 bar (2016 psi) rating.
82,7
(1200)
68,9
(1000)
55,2
(800)
41,4
(600)
27,6
(400)
13,8
(200)
0
(0)
-15
(0)
40
(100)
95
(200)
150
(300)
200
(400)
260
(500)
O-RING
(SEAL)
“O”-Ring
Material
Max. Process
Temperature
SELECTION
O-RING/SEAL SPECIFICATIONS
Code
Min. Process Max. Process
Temperature
Pressure
CHART
Not Recommended For
Applications
Recommended for Applications
0
Viton® GFLT
200 °C @ 16 bar
(400 °F @ 230 psi)
-40 °C
(-40 °F)
Ketones (MEK, acetone),
skydrol fluids, amines,
70 bar @ 20 °C anhydrous ammonia, low
(1000 psi
molecular weight esters and
70 °F)
ethers, hot hydrofluoric or
chlorosulfuric acids, sour
HCs
1
EPDM
120 °C @14 bar
(250 °F @ 200 psi)
-50 °C
(-60 °F)
70 bar @ 20 °C Petroleum oils, di-ester base
(1000 psi
lubricant, steam
70 °F)
200 °C @ 16 bar
(400 °F @ 232 psi)
-40 °C
(-40 °F)
70 bar @ 20 °C
(1000 psi
70 °F)
-20 °C
(-4 °F)
Halogenated HCs, nitro HCs,
phosphate ester hydraulic
70 bar @ 20 °C
fluids, ketones (MEK,
(1000 psi
acetone),
strong acids,
70 °F)
ozone, automotive brake
fluid, steam
NACE applications
General purpose sealing,
petroleum oils and fluids, cold
water, silicone greases and oils,
di-ester base lubricants, ethylene
glycol base fluids
2
3
®
Kalrez 4079
HSN
135 °C @ 22 bar
(Highly Saturated (275 °F @ 320 psi)
Nitrile)
Hot water/steam, hot
aliphatic amines, ethylene
oxide, propylene oxide
General purpose, ethylene
Acetone, MEK, skydrol fluids
Inorganic and organic acids (including
hydro fluids and nitric), aldehydes,
ethylene, organic oils, blycols, silicone
oils, vinegar, sour HCs
4
Buna-N
135 °C @ 22 bar
(275 °F @ 320 psi)
-20 °C
(-4 °F)
Halogenated HCs, nitro HCs,
phosphate ester hydraulic
70 bar @ 20 °C
fluids, ketones (MEK,
(1000 psi
acetone), strong acids,
70 °F)
ozone, automotive brake
fluid
5
Neoprene®
150 °C @ 20 bar
(300 °F @ 290 psi)
-55 °C
(-65 °F)
70 bar @ 20 °C
(1000 psi
70 °F)
Phosphate ester fluids,
ketones (MEK, acetone)
Refrigerants, high anline point
petroleum oils, silicate ester
lubricants
Acetaldehyde, ammonia +
lithium metal solution,
butyraldehyde, di-water,
freon, ethylene oxide,
liquors, isobutyraldehyde
Inorganic and organic acids,
alkalines, ketones, esters,
aldehydes, fuels
Acids, Ketones,
chlorinated HCs,
Hydraulic systems, petroleum oils,
HC fuel, oxygen, ozone
6
Chemraz® 505
200 °C @ 14 bar
(400 °F @ 200 psi)
-20 °F
(-30 °C)
70 bar @ 20 °C
(1000 psi
70 °F)
7
Polyurethane
95 °C @ 29 bar
(200 °F @ 420 psi)
-55 °C
(-65 °F)
70 bar @ 20 °C
(1000 psi
70 °F)
200 °C @ 16 bar
(400 °F @ 232 psi)
-20 °C
(-4 °F)
Black liquor, freon 43, freon
70 bar @ 20 °C 75, galden, KEL-F liquid,
(1000 psi
molten potassium, molten
70 °F)
sodium
200 °C @ 16 bar
(400 °F @ 232 psi)
-40 °C
(-40 °F)
70 bar @ 20 °C
(1000 psi
70 °F)
Hot water/steam, hot
aliphatic amines, ethylene
oxide, propylene oxide
Inorganic and organic acids (including
hydro fluids and nitric), aldehydes,
ethylene, organic oils, blycols,
silicone oils, vinegar, sour HCs
Glass Ceramic 450 °C @ 248 bar
D or N
(850 °F @ 3600 psi)
Alloy
-195 °C
(-320 °F)
431 bar @
20 °C
(6250 psi
70 °F)
Hot alkaline solutions HF acid,
media with ph>12,
direct exposure to
saturated steam
General high temperature/high
pressure applications,
hydrocarbons, full vacuum
(hermetic), ammonia, chlorine
8
A
Aegis PF128 ¿
®
Kalrez 6375
Inorganic and organic acids
(including hydro fluids and nitric),
aldehydes, ethylene, organic oils,
gycols, silicone oils, vinegar, sour
HCs, steam, amines, ethylene oxide,
propylene oxice, NACE applications
¿ Maximum +150 °C (+300 °F) for use on steam.
17
REPLACEMENT
OF
DISPLACER
ECLIPSE has proven to be the ideal replacement for existing torque tube transmitters. In numerous applications
worldwide, customers have found the performance of
ECLIPSE Guided Wave Radar transmitters to be superior to
that of antiquated torque tube transmitters.
There are several benefits to using the ECLIPSE Model 706
as a replacement for torque tube transmitters:
• Cost:
The cost of a new Model 706 transmitter cost is comparable to rebuilding an aging torque tube.
• Installation:
No field calibration is necessary. The Model 706 transmitter can be configured in minutes with no level movement. (Complete factory pre-configuration is available,
which can further decrease the installation effort).
• Performance:
The ECLIPSE Model 706 is unaffected by changes in
specific gravity and has no moving parts that can wear
and lose tolerance.
TRANSMITTERS
• Ease of replacement:
Proprietary and standard ANSI flanges are offered on all
ECLIPSE Model 706 probes so existing chamber/cages
can be used.
In order to match the proper ECLIPSE transmitter with the
proper external cage, consider the following:
• Type of application:
Use the proper GWR probe for the application, see
pages 7 and 10 through 16.
• Overfill proof:
For optimum performance, use an Overfill-safe probe
in all chamber applications.
Note: “Overfill” occurs when the level rises above
the maximum range of operation. Some
GWR probes may provide erroneous output
in this zone unless an optimal, impedancematched design is used.
• Minimum Cage Size:
• Coaxial or Caged Coaxial probes: 2" minimum
• Enlarged Coaxial probes: 3" minimum
• Twin Cable probes: 4" minimum
Before
Body connection
E
20 mA / 100 %
Measuring range:
min 30 cm (12")
max 570 cm (224")
H
Displacer
length
P
Probe insertion length =
E + measuring range + F
After
4 mA / 0 %
F
min 25 mm (1")
Recommended probe length for replacing displacer transmitters
The table below helps to define the GWR probe length for the most common displacer transmitters.
Refer to the proprietary flange selection guide.
Manufacturer
Type
Process Connection
MAGNETROL
EZ & PN Modulevel®
Masoneilan®
Series 1200
Fisher® series
2300 & 2500
Eckardt®
249B, 259B, 249C cages
other cages
Series 134, 144
Tokyo Keiso®
FST-3000
ANSI/EN flange
Proprietary flange
ANSI/EN flange
Proprietary flange
ANSI flange
ANSI/EN flange
ANSI/EN flange
ANSI/EN flange
¿ Round down resulting calculation to the nearest inch.
18
Displacer Length
mm (inches)
≥ 356 (14)
≥ 356 (14)
≥ 406 (16)
≥ 356 (14)
≥ 356 (14)
≥ 356 (14)
H = 300 (11.8)
≥ H = 500 (19.7)
Probe Length ¿
mm (inches)
Displacer + 178 (7)
Displacer + 203 (8)
Displacer + 203 (8)
Displacer + 254 (10)
consult factory
consult factory
Displacer + 229 (9)
Displacer + 229 (9)
PROPRIETARY
mm
FLANGES
(INCHES)
Ø 184 (7.25)
Ø 229 (9)
Ø 143 (5.62)
Ø 191 (7.50)
Ø 121 (4.75)
45°
45°
Ø 22
(0.87)
45°
Ø 11
(0.43)
Ø 22
(0.87)
32
(1.25)
133
(5.23)
29
(1.12)
86
(3.37)
6
(0.22)
Fisher 249B/259B (600 lbs.), carbon steel
MAGNETROL
Ø 149 (5.875)
32
(1.25)
102
(4)
5
(0.188)
Fisher 249C (600 lbs.), 316 stainless steel
6
(0.25)
Masoneilan (600 lbs.), carbon steel
CHAMBERS
A brief description of the MAGNETROL chamber offering follows. For more details, refer to
MAGNETROL Sales Bulletin BE57-140.
MAGNETROL has a long tradition in offering cost-effective chambers. The MAGNETROL external
chamber is a self-contained cage designed for use with our top mounting level transmitters or
switches. Quality construction and a wide selection of configurations make this cage an ideal means
of utilizing the power of Guided Wave Radar without mounting directly into the process vessel.
MAGNETROL chambers are available with a wide variety
of options, and can be manufactured to comply with various regulations such as:
• Commercial Design
Some Model 706 probes can be installed into chambers
as small as 2". When a new chamber is required, it can be
ordered together with a factory pre-configured Model 706
for a true “plug and play” installation.
• ASME B31.1 Design Code
• ASME B31.3 Design Code
• NACE Design Code
• PED
Measuring
Measuring
Range
Range
Measuring
Measuring
Range
Range
NPT drain
1"1"NPT
drain
Sealed Chamber
Slip-on head flange
Measuring
Measuring
Range
Range
NPT drain
1"1"NPT
drain
Weld neck head flange
19
AGENCY
APPROVALS
These units are in compliance with the EMC-directive 2014/30/EU, the PED-directive 2014/68/EU and the ATEX directive 2014/34/EU.
IEC 60079-0: 2001
IEC 60079-15: 2010
IEC 60079-26: 2006
Explosion Proof (with intrinsically Safe Probe)
Non- Incendive
US/Canada:
Class I, Div 1, Group B, C and D, T4
Class I, Zone 1 AEx d/ia [ia IIC Ga] IIB + H2 T4 Gb/Ga
Class I, Zone 1 Ex d/ia [ia IIC Ga] IIB + H2 T4 Gb/Ga
Ta = -40ºC to +70ºC
Type 4X, IP67
US/Canada:
Class I, II, III, Division 2, Group A, B, C, D, E, F, G, T4
Class I, Zone 2 AEx ia/nA [ia Ga] IIC T4 Ga/Gc
Class I, Zone 2 Ex ia/nA [ia Ga] IIC T4 Ga/Gc
Ta = -40ºC to +70ºC
Type 4X, IP67
Flame Proof
ATEX – FM14ATEX0041X:
II 2/1 G Ex d/ia [ia IIC Ga] IIB + H2 T6 to T1 Gb/Ga
Ta = -40ºC to +70ºC
IP67
ATEX
II 1/3 G Ex ia/nA [ia Ga] IIC T4 Ga/Gc
Ta = -15ºC to +70ºC
IP67
IEC- IECEx FMG 14.0018X:
Ex d/ia [ia IIC Ga] IIB + H2 T6 to T1 Gb/Ga
Ta = -40ºC to +70ºC
IP67
IEC – IECEx FMG 14.00018X:
Ex ia/nA [ia Ga] IIC T4 Ga/Gc
Ta = -15ºC to + 70ºC
IP67
Intrinsically Safe
Dust Ignition Proof
US/Canada:
Class I, II, III, Div 1, Group A, B, C, D, E, F, G, T4,
Class I, Zone 0 AEx ia IIC T4 Ga
Class I, Zone 0 Ex ia IIC T4 Ga
Ta =-40ºC to + 70ºC
Type 4X, IP67
US/Canada:
Class II, III, Division 1, Group E, F and G, T4
Ta = -40ºC to +70ºC
Type 4X, IP67
ATEX – FM14ATEX0041X:
II 1 G Ex ia IIC T4 Ga
Ta = -40ºC to +70ºC
IP67
IEC – IECEx FMG 14.0018X:
Ex ia IIC T4 Ga
Ta = -40ºC to +70ºC
IP67
ATEX – FM14ATEX0041X:
II 1/2 D Ex ia/tb [ia Da] IIIC T85ºC to T450ºC Da/Db
Ta = -15ºC to +70ºC
IP67
IEC – IECEx FMG 14.0018X:
Ex ia tb [ia Da] IIIC T85ºC to T450ºC Db
Ex ia IIIC T85ºC to T450ºC Da
Ta = -15ºC to +70ºC
IP67
The following approval standards are applicable:
FM3600:2011, FM3610:2010, FM3611:2004, FM3615:2006, FM3616:2011, FM3810:2005, ANSI/ISA60079-0:2013,
ANSI/ISA 60079-1:2009, ANSI/ISA 60079-11:2013, ANSI/ISA 60079-15:2012, ANSI/ISA 60079-26:2011, NEMA 250:2003,
ANSI/IEC 60529:2004, C22.2 No. 0.4:2009, C22.2 No. 0.5:2008, C22.2 No. 30:2007, C22.2 No. 94:2001, C22.2 No. 157:2012,
C22.2 No. 213:2012, C22.2 No. 1010.1:2009, CAN/CSA 60079-0:2011, CAN/CSA 60079-1:2011, CAN/CSA 60079-11:2011,
CAN/CSA 60079-15:2012, C22.2 No. 60529:2005, EN60079-0:2012, EN60079-1:2007, EN60079-11:2012, EN60079-15:2010,
EN60079-26:2007, EN60079-31:2009, EN60529+A1:1991-2000, IEC60079-0:2011, IEC60079-1:2007, IEC60079-11:2011,
IEC60079-15:2010, IEC60079-26:2006, IEC60079-31:2008
20
AGENCY
APPROVALS
Special Conditions of Use
1. The enclosure contains aluminum and is considered to present a potential risk of ignition by impact or
friction. Care must be taken during installation and use to prevent impact or friction.
2. The risk of electrostatic discharge shall be minimized at installation, following the directions given in the instructions.
3. Contact the original manufacturer for information on the dimensions of the flameproof joints.
4. For installation with ambient temperature of +70 °C, refer to the manufacturer’s instructions for guidance on
proper selection of conductors.
5. WARNING—Explosion Hazard: Do not disconnect equipment when flammable or combustible atmoshpere
is present.
6. For IEC and ATEX: To maintain the T1 to T6 temperature codes, care shall be taken to ensure the enclosure
temperature does not exceed +70 °C.
7. For U.S. and Canada: To maintain the T4 temperature code, care shall be taken to ensure the enclosure
temperature does not exceed +70 °C.
8. Temperature codes for the ratings Ex d/ia [ia IIC] IIB+H2 and Ex ia/tb [ia] IIIC are defined by the following
table:
Process Temperature (PT)
Temperature Code-TCG
(GAS)
Temperature Code-TCD
(Dust)
Up to 75°C
T6
TCD= PT+10K=85°C
From 75°C to 90°C
T5
TCD= PT+10K=100°C
From 90°C to 120°C
T4
TCD= PT+15K=135°C
From 125°C to 185°C
T3
TCD= PT+15K=200°C
From 185°C to 285°C
T2
TCD= PT+15K=300°C
From 285°C to 435°C
T1
TCD= PT+15K=450°C
Agency Specifications – Explosion Proof Installation
Factory Sealed: This product has been approved by Factory Mutual Research (FM) and Canadian Standards
Association (CSA) as a Factory Sealed device.
NOTE: Factory Sealed: No Explosion Proof conduit fitting (EY seal) is required within 18" of the transmitter.
However, an Explosion Proof conduit fitting (EY seal) is required between the hazardous and safe areas.
EXPEDITE SHIP PLAN (ESP)
Several models are available for quick shipment, within max. 4 weeks after factory receipt of purchase order, through the Expedite
Ship Plan (ESP).
Models covered by ESP service are conveniently colour coded in the selection data charts.
To take advantage of ESP, simply match the colour coded model number codes (standard dimensions apply).
ESP service may not apply to orders of five units or more. Contact your local representative for lead times on larger volume orders,
as well as other products and options.
21
MODEL
NUMBER
TRANSMITTER
1 2 3 | BASIC MODEL NUMBER
706
ECLIPSE 4th Generation Guided Wave Radar (GWR) Level Transmitter
4 | POWER
5
24 VDC, Two-Wire
5 | SIGNAL OUTPUT
1
4 –20 mA with HART
2
FOUNDATION fieldbus™ Communications
4
Modbus Communication (8th Digit = 0 or 3 only)
6 | SAFETY OPTIONS
0
None – FOUNDATION fieldbus and Modbus only (5th digit = 2 or 4)
1
SIL 2 Hardware - HART only (5th digit = 1)
7 | ACCESSORIES/MOUNTING
0
No Digital Display or Keypad - Integral
1
No Digital Display or Keypad - 1 m (3') remote
2
No Digital Display or Keypad - 3,6 m (12') remote
A
Digital Display and Keypad - Integral
B
Digital Display and Keypad - 1 m (3') remote
C
Digital Display and Keypad - 3,6 m (12') remote
8 | CLASSIFICATION
0
General Purpose, Weatherproof (IP 67)
1
Intrinsically Safe (FM & CSA CL 1 Div 1, Grps A, B, C, D) (5th digit = 1 or 2)
3
Explosion-proof (FM & CSA CL 1 Div 1, Grps B, C, D)
A
Intrinsically Safe (ATEX/IEC Ex ia IIC T4) (5th digit = 1 or 2)
B
Flame-proof (ATEX/IEC Ex d ia IIC T6) (5th digit = 1 or 2)
C
Non-incendive (ATEX Ex n IIC T6) (5th digit = 1 or 2)
D
Dust Ex (ATEX II) (5th digit = 1 or 2)
9 | HOUSING
1
Die-cast Aluminum, Dual-compartment, 45-degree
2
Investment Cast, 316 SS, Dual-compartment, 45-degree
10 | CONDUIT CONNECTION
22
7
0
6
5
1
2
3
4
5
6
7
8
9
0
1
1
M20
2
1
3
M20 with sunshade
10
⁄2" NPT
⁄2" NPT with sunshade
DIMENSIONS
mm
(inches)
86
(3.38)
106
(4.18)
96
(3.77)
212
(8.34)
86
(3.38)
236
(9.30)
106
(4.18)
129
(5.09)
96
(3.77)
2 cable
entries
102
(4.03)
45 °
Integral Electronics
Eclipse® Housing
(45° View)
2 cable
entries
60
(2.37)
45 °
76
(3.00)
51
(2.00)
89
(3.50)
838 or 3650
(33 or 144)
95
(3.75)
2 holes
Ø 10 (0.38)
105
(4.15)
Eclipse® Remote Configurations
ELECTRICAL
WIRING
HART® modem
0% 100%
Standard shielded
twisted cable
(recommended but not needed when
wired as per NAMUR NE 21 for field
strenghts up to 10 V/m).
Ex
Galvanic Barrier :
Entity parameters per Agency Certificate
(not needed for GP, Dust Ex, and explosion-proof models).
250Ω minimum required for HART Communications
Non Ex
23
MODEL
NUMBER
ENLARGED
COAXIAL
PROBE
1 | TECHNOLOGY
7
ECLIPSE GWR Probes - Model 706
2 | MEASUREMENT SYSTEM
A
English
C
Metric
3 | CONFIGURATION/STYLE (RIGID)
D
Enlarged Coaxial, High Temp/High Pressure: Overfill w/Glass Seal (+450 °C/+850 °F) — Available only with 10th digit N or D
P
Enlarged Coaxial, High Pressure: Overfill w/Glass Seal (+200 °C/+400 °F) — Available only with 10th digit N or D
T
Enlarged Coaxial, Overfill Standard O-Ring Seal (+200 °C/+400 °F) — Not available with 10th digit N or D
4 5 | PROCESS CONNECTION – SIZE/TYPE (consult factory for other process connections)
Threaded
2" NPT Thread ¿
41
42
2" BSP (G 2") Thread ¿
ANSI Flanges
43
2"
44
2"
45
2"
150# ANSI RF ¿
300# ANSI RF ¿
5M
3"
1500# ANSI RTJ
5N
3"
2500# ANSI RTJ
4"
150# ANSI RF
4K
600# ANSI RTJ ¿
63
2"
64
4"
300# ANSI RF
53
3"
150# ANSI RF
65
4"
600# ANSI RF
54
3"
300# ANSI RF
66
4"
900# ANSI RF
55
3"
600# ANSI RF
67
4"
1500# ANSI RF
56
3"
900# ANSI RF
68
4"
2500# ANSI RF
57
3"
1500# ANSI RF
6K
4"
600# ANSI RTJ
58
3"
2500# ANSI RF
6L
4"
900# ANSI RTJ
5K
3"
600# ANSI RTJ
6M
4"
1500# ANSI RTJ
5L
3"
900# ANSI RTJ
6N
4"
2500# ANSI RTJ
600# ANSI RF ¿
EN Flanges
DN 50, PN 16
EN 1092-1 TYPE A ¿
DN 80, PN 320
EN 1092-1 TYPE B2
DB
DN 50, PN 25/40 EN 1092-1 TYPE A ¿
EH
DN 80, PN 400
EN 1092-1 TYPE B2
DN 50, PN 63
EN 1092-1 TYPE B2 ¿
EJ
DD
DN 100, PN 16
EN 1092-1 TYPE A
DE
DN 50, PN 100
EN 1092-1 TYPE B2 ¿
FA
FB
DN 100, PN 25/40
EN 1092-1 TYPE A
EA
DN 80, PN 16
EN 1092-1 TYPE A
FD
DN 100, PN 63
EN 1092-1 TYPE B2
EB
DN 80, PN 25/40
EN 1092-1 TYPE A
FE
DN 100, PN 100
EN 1092-1 TYPE B2
ED
DN 80, PN 63
EN 1092-1 TYPE B2
FF
DN 100, PN 160
EN 1092-1 TYPE B2
EE
DN 80, PN 100
EN 1092-1 TYPE B2
FG
DN 100, PN 250
EN 1092-1 TYPE B2
EF
DN 80, PN 160
EN 1092-1 TYPE B2
FH
DN 100, PN 320
EN 1092-1 TYPE B2
EG
DN 80, PN 250
EN 1092-1 TYPE B2
FJ
DN 100, PN 400
EN 1092-1 TYPE B2
TT
600# Fisher (249B/259B) in carbon steel – as per dimensions on page 18
TU
600# Fisher (249C) in stainless steel – as per dimensions on page 18
UT
600# Masoneilan flange in carbon steel – as per dimensions on page 18
UU
600# Masoneilan flange in stainless steel – as per dimensions on page 18
DA
Torque Tube Mating Flanges ¡
¿ Confirm mounting conditions/nozzle diameter to ensure sufficient clearance.
¡ Always check dimensions if ANSI/EN flanges are not used.
7
1
24
2
3
4
5
6
7
8
9
10
11
12
13
14
15
MODEL
NUMBER
ENLARGED
COAXIAL
CONTINUED
PROBE
6 | CONSTRUCTION CODES
0
K
L
M
N
Industrial
ASME B31.1
ASME B31.3
ASME B31.3 & NACE MR0175/MR0103 — NOT available with carbon steel flange
NACE MR0175/MR0103 — NOT available with carbon steel flange
7 | FLANGE OPTIONS — Offset flanges are only available with small coaxial probes
0
None
8 | MATERIAL OF CONSTRUCTION - FLANGE/NUT/ROD/INSULATION
A
316 SS/316L SS (Probe O.D. 45 mm (1.75”))
B
C
R
S
Hastelloy C (Probe O.D. 49 mm (1.93”))
Monel (Probe O.D. 49 mm (1.93”))
316 SS/316L SS with Carbon Steel Flange (Probe O.D. 45 mm (1.75”))
Hastelloy C with Carbon Steel Flange (Probe O.D. 49 mm (1.93”))
T
Monel with Carbon Steel Flange (Probe O.D. 49mm (1.93”))
9 | SPACER MATERIAL
1
2
3
4
5
TFE (+200 °C/+400 °F) — Available only with 3rd digit P or T — εr ≥ 1.4
PEEK HT — Available only with 3rd digit D (+345 °C/+650 °F) — εr ≥ 1.4
Ceramic (High Temp. >+425 °C/+800 °F) — Available only with 3rd digit D — εr ≥ 2.0
Celazole (+425 °C/+800 °F) — Available only with 3rd digit D — εr ≥ 1.4
None - with metal shorting rod — εr ≥ 1.4 — Future
10 | O-RING MATERIALS/SEAL OPTIONS
0
Viton® GFLT — Available only with 3rd digit T
2
Kalrez® 4079 — Available only with 3rd digit T
8
Aegis PF 128 (NACE) — Available only with 3rd digit T
A
Kalrez 6375 — Available only with 3rd digit T
B
HF Acid Probe — Only available with 3rd digit T and 8th digit C
D
None/Glass Ceramic Alloy (dual-seal design with annunciator fitting)—Only available with 3rd digit D or P
N
None/Glass Ceramic Alloy — Available only with 3rd digit D, P or S
11 | PROBE SIZE/ELEMENT TYPE/FLUSHING CONNECTION
0
1
Standard Enlarged Coaxial Probe
Standard Enlarged Coaxial Probe with Flushing Port
12 | SPECIAL OPTIONS — See page 36
0
1
2
3
4
5
6
Single Length Probe (Non-Segmented)
1-piece Segmented Probe OD=64mm (2.5”)
2-piece Segmented Probe OD=64mm (2.5”)
3-piece Segmented Probe OD=64mm (2.5”)
4-piece Segmented Probe OD=64mm (2.5”)
5-piece Segmented Probe OD=64mm (2.5”)
6-piece Segmented Probe OD=64mm (2.5”)
13 14 15 | INSERTION LENGTH
cm (030 – 999)
inches (012 – 396)
XXX
unit of measure determined
by 2nd digit of model number
7
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
25
MODEL
SMALL
NUMBER
COAXIAL
PROBE
1 | TECHNOLOGY
7
ECLIPSE GWR Probes - Model 706
2 | MEASUREMENT SYSTEM
A
C
English
Metric
3 | CONFIGURATION/STYLE (RIGID)
D
P
S
T
Small Coaxial, High Temp/High Pressure: Overfill w/Glass Seal (+450 °C/+850 °F) — Only available with 10th digit N or D
Small Coaxial, High Pressure: Overfill w/Glass Seal (+200 °C/+400 °F) — Only available with 10th digit N or D
Small Coaxial, Saturated Steam (+300 °C/+345 °C [+575 °F/+650 °F]), Max. Length=610 cm (240”) — Only available with 10th digit N, 9th digit 2 or 3
Small Coaxial, Overfill Standard O-Ring Seal (+200 °C/+400 °F) — Not available with 10th digit N or D
4 5 | PROCESS CONNECTION – SIZE/TYPE (consult factory for other process connections)
Threaded
3
⁄4" NPT Thread ¬
11
22
1" BSP (G 1") Thread ¬
2" NPT Thread – Only available with 3rd Digit D
41
ANSI Flanges
23
24
25
2K
33
34
35
3K
37
3M
1"
1"
1"
1"
1 1⁄2"
1 1⁄2"
1 1⁄2"
1 1⁄2"
1 1⁄2"
1 1⁄2"
150# ANSI RF ¿ √
3 8 1 1⁄2"
300# ANSI RF ¿ √
3 N 1 1⁄2"
600# ANSI RF ¿ √
4 3 2"
600# ANSI RTJ ¿ √ 4 4 2"
150# ANSI RF √
4 5 2"
300# ANSI RF √
4 7 2"
600# ANSI RF √
4 8 2"
600# ANSI RTJ √
4 K 2"
900/1500# ANSI RF√ 4 M 2"
900/1500# ANSI RTJ√ 4 N 2"
2500# ANSI RF √
2500# ANSI RTJ √
150# ANSI RF
300# ANSI RF
600# ANSI RF
900/1500# ANSI RF
2500# ANSI RF
600# ANSI RTJ
900/1500# ANSI RTJ
2500# ANSI RTJ
EN Flanges
53
54
55
56
57
58
5K
5L
5M
5N
A¿√
B2 ¿ √
A√
B2 √
B2 √
B2 √
B2 √
B2 √
BB
BC
CB
CC
CF
CG
CH
CJ
DA
DB
DD
DE
DF
DG
DH
DJ
DN
DN
DN
DN
DN
DN
DN
DN
25,
25,
40,
40,
40,
40,
40,
40,
PN
PN
PN
PN
PN
PN
PN
PN
16/25/40 EN
63/100 EN
16/25/40 EN
63/100 EN
160
EN
250
EN
320
EN
400
EN
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
DN
DN
DN
DN
50,
50,
50,
50,
PN
PN
PN
PN
16
25/40
63
100
EN
EN
EN
EN
1092-1
1092-1
1092-1
1092-1
TYPE
TYPE
TYPE
TYPE
DN
DN
DN
DN
50,
50,
50,
50,
PN
PN
PN
PN
160
250
320
400
EN
EN
EN
EN
1092-1
1092-1
1092-1
1092-1
TYPE
TYPE
TYPE
TYPE
TT
TU
UT
UU
600#
600#
600#
600#
Torque Tube Mating Flanges ¡
42
EA
EB
ED
EE
EF
EG
EH
E J
FA
FB
FD
FE
FF
FG
FH
FJ
A
A
B2
B2
B2
B2
B2
B2
2" BSP (G 2") Thread – Only available with 3rd Digit D
3"
3"
3"
3"
3"
3"
3"
3"
3"
3"
150# ANSI RF
300# ANSI RF
600# ANSI RF
900# ANSI RF
1500# ANSI RF
2500# ANSI RF
600# ANSI RTJ
900# ANSI RTJ
1500# ANSI RTJ
2500# ANSI RTJ
DN
DN
DN
DN
DN
DN
DN
DN
DN
DN
DN
DN
DN
DN
DN
DN
4"
4"
4"
4"
4"
4"
4"
4"
4"
4"
63
64
65
66
67
68
6K
6L
6M
6N
80, PN 16
80, PN 25/40
80, PN 63
80, PN 100
80, PN 160
80, PN 250
80, PN 320
80, PN 400
100, PN 16
100, PN 25/40
100, PN 63
100, PN 100
100, PN 160
100, PN 250
100, PN 320
100, PN 400
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
150# ANSI RF
300# ANSI RF
600# ANSI RF
900# ANSI RF
1500# ANSI RF
2500# ANSI RF
600# ANSI RTJ
900# ANSI RTJ
1500# ANSI RTJ
2500# ANSI RTJ
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
Fisher (249B/259B) in carbon steel – as per dimensions on page 18
Fisher (249C) in stainless steel – as per dimensions on page 18
Masoneilan flange in carbon steel – as per dimensions on page 18
Masoneilan flange in stainless steel – as per dimensions on page 18
¿
¡
¬
√
Confirm mounting conditions/nozzle diameter to ensure sufficient clearance.
Always check dimensions if ANSI/EN flanges are not used.
Not available with 3rd digit ‘D’
Not available with 3rd digit ‘D’ or 'P'
7
1
26
2
3
4
A
A
B2
B2
B2
B2
B2
B2
A
A
B2
B2
B2
B2
B2
B2
5
6
7
8
9
10
11
12
13
14
15
MODEL
SMALL
NUMBER
COAXIAL
CONTINUED
PROBE
6 | CONSTRUCTION CODES
0
K
L
M
N
Industrial
ASME B31.1 — NOT available with 4th digits T or U
ASME B31.3
ASME B31.3 & NACE MR0175/MR0103 — NOT available with carbon steel flange
NACE MR0175/MR0103 — NOT available with carbon steel flange
7 | FLANGE OPTIONS — Offset flanges are only available with small coaxial probes
0
1
2
3
None
Offset (For use with AURORA) — 4”/DN 100 Only available with 3rd digit P, S or T
Offset with 1⁄2" NPT Vent (For use with AURORA) — 4”/DN 100 Only available with 3rd digit P, S or T
Offset with 3⁄4" NPT Vent (For use with AURORA) — 4”/DN 100 Only available with 3rd digit P, S or T
8 | MATERIAL OF CONSTRUCTION - FLANGE/NUT/ROD/INSULATION
A
B
C
R
S
T
316 SS/316L SS
Hastelloy C
Monel — Not available with 3rd Digit S
316 SS/316L SS with Carbon Steel Flange
Hastelloy C with Carbon Steel Flange
Monel with Carbon Steel Flange — Not available with 3rd Digit S
9 | SPACER MATERIAL
1
2
3
5
TFE (+200 °C/+400 °F) — Only available with 3rd digit P or T — εr ≥ 1.4
PEEK HT — Only available with 3rd digit D — εr ≥ 1.4 (+345 °C/+650 °F) or S (+300 °C/+575 °F)
Ceramic (Temp. >+345 °C/+650 °F) — Only available with 3rd digit D — εr ≥ 2.0 or with 3rd digit S
None - with metal shorting rod — εr ≥ 1.4 — Future
10 | O-RING MATERIALS/SEAL OPTIONS
0
Viton® GFLT — Only Available with 3rd digit T
2
Kalrez® 4079 — Only Available with 3rd digit T
8
Aegis PF 128 (NACE) — Only Available with 3rd digit T
A
Kalrez 6375 — Only Available with 3rd digit T
B
HF Acid Probe — Only available with 3rd digit T and 8th digit C
D
None/Glass Ceramic Alloy (dual-seal design with annunciator fitting)—Only available with 3rd digit D or P
N
None/Glass Ceramic Alloy — Available only with 3rd digit D, P or S
11 | PROBE SIZE/ELEMENT TYPE/FLUSHING CONNECTION
2
Small Coaxial (22 mm/0.875 inches)
12 | SPECIAL OPTIONS
0
Single Length Probe (Non-Segmented)
13 14 15 | INSERTION LENGTH
cm (030 – 610)
inches (012 – 240)
XXX
unit of measure determined
by 2nd digit of model number
7
1
2
2
3
4
5
6
7
8
9
10
11
12
13
14
15
27
MODEL
CAGED
NUMBER
PROBE
1 | TECHNOLOGY
7
ECLIPSE GWR Probes - Model 706
2 | MEASUREMENT SYSTEM
A
English
C
Metric
3 | CONFIGURATION/STYLE (RIGID)
G
Overfill Caged Rigid Probe for use in chambers +200 °C (+400 °F)
J
Overfill Caged High Temp/High Pressure Probe with Glass Seal for use in chambers +450 °C (+850 °F)
L
Overfill Caged High Pressure Probe with Glass Seal for use in chambers +200 °C (+400 °F)
4 5 | PROCESS CONNECTION – SIZE/TYPE (consult factory for other process connections) ¿
ANSI Flanges
43
2"
150# ANSI RF
54
3"
300# ANSI RF
63
4"
150# ANSI RF
44
2"
300# ANSI RF
55
3"
600# ANSI RF
64
4"
300# ANSI RF
45
2"
600# ANSI RF
56
3"
900# ANSI RF
65
4"
600# ANSI RF
47
2"
900/1500# ANSI RF
57
3"
1500# ANSI RF
66
4"
900# ANSI RF
48
2"
2500# ANSI RF
58
3"
2500# ANSI RF
67
4"
1500# ANSI RF
4K
2"
600# ANSI RTJ
5K
3"
600# ANSI RTJ
68
4"
2500# ANSI RF
4M
2"
900/1500# ANSI RTJ
5L
3"
900# ANSI RTJ
6K
4"
600# ANSI RTJ
4N
2"
2500# ANSI RTJ
5M
3"
1500# ANSI RTJ
6L
4"
900# ANSI RTJ
53
3"
150# ANSI RF
5N
3"
2500# ANSI RTJ
6M
4"
1500# ANSI RTJ
6N
4"
2500# ANSI RTJ
EN Flanges
DA
DN 50, PN 16
EN 1092-1 TYPE A
EF
DN 80, PN 160
EN 1092-1 TYPE B2
DB
DN 50, PN 25/40
EN 1092-1 TYPE A
EG
DN 80, PN 250
EN 1092-1 TYPE B2
DD
DN 50, PN 63
EN 1092-1 TYPE B2
EH
DN 80, PN 320
EN 1092-1 TYPE B2
DE
DN 50, PN 100
EN 1092-1 TYPE B2
E J
DN 80, PN 400
EN 1092-1 TYPE B2
DF
DN 50, PN 160
EN 1092-1 TYPE B2
FA
DN 100, PN 16
EN 1092-1 TYPE A
DG
DN 50, PN 250
EN 1092-1 TYPE B2
FB
DN 100, PN 25/40
EN 1092-1 TYPE A
DH
DN 50, PN 320
EN 1092-1 TYPE B2
FD
DN 100, PN 63
EN 1092-1 TYPE B2
DJ
DN 50, PN 400
EN 1092-1 TYPE B2
FE
DN 100, PN 100
EN 1092-1 TYPE B2
EA
DN 80, PN 16
EN 1092-1 TYPE A
FF
DN 100, PN 160
EN 1092-1 TYPE B2
EB
DN 80, PN 25/40
EN 1092-1 TYPE A
FG
DN 100, PN 250
EN 1092-1 TYPE B2
ED
DN 80, PN 63
EN 1092-1 TYPE B2
FH
DN 100, PN 320
EN 1092-1 TYPE B2
EE
DN 80, PN 100
EN 1092-1 TYPE B2
FJ
DN 100, PN 400
EN 1092-1 TYPE B2
Torque Tube Mating Flanges ¡
TT
600# Fisher (249B/259B) in carbon steel – as per dimensions on page 18
TU
600# Fisher (249C) in stainless steel – as per dimensions on page 18
UT
600# Masoneilan flange in carbon steel – as per dimensions on page 18
UU
600# Masoneilan flange in stainless steel – as per dimensions on page 18
¿ Confirm mounting conditions/nozzle diameter to ensure sufficient clearance.
¡ Always check dimensions if ANSI/EN flanges are not used.
7
1
28
2
3
4
5
6
7
8
9
10
11
12
13
14
15
MODEL
CAGED
NUMBER
CONTINUED
PROBE
6 | CONSTRUCTION CODES
0
Industrial
K
ASME B31.1
L
ASME B31.3
M
ASME B31.3 & NACE MR0175/MR0103 — NOT available with carbon steel flange
N
NACE MR0175/MR0103 — NOT available with carbon steel flange
7 | FLANGE OPTIONS
0
None
1
Offset (For use with AURORA)– 4"/DN 100 Only available with 3rd digit G and J and 4th digit 6
2
Offset with 1⁄2" NPT Vent (For use with AURORA)– 4"/DN 100 Only available with 3rd digit G and J and 4th digit 6
3
Offset with 3⁄4" NPT Vent (For use with AURORA)– 4"/DN 100 Only available with 3rd digit G and J and 4th digit 6
8 | MATERIAL OF CONSTRUCTION - MFG/NUT/ROD/INSULATION
A
316 SS/316L SS
B
Hastelloy C
C
Monel
R
316 SS/316L SS with Carbon Steel Flange
S
Hastelloy C with Carbon Steel Flange
T
Monel with Carbon Steel Flange
9 | SPACER MATERIAL
2
PEEK HT (+345 °C/+650 °F)
3
Ceramic (High Temp.>+800 °F/+425 °C) — Only available with 3rd digit J
4
Celazole® (+800 °F/+425 °C) — Only available with 3rd digit J
10 | O-RING MATERIALS/SEAL OPTIONS
0
Viton® GFLT — Not available with 3rd digit J or L
2
Kalrez 4079 — Not available with 3rd digit J or L
8
Aegis PF 128 (NACE) — Not available with 3rd digit J or L
A
Kalrez 6375 — Not available with 3rd digit J or L
B
HF Acid Probe — Only Available with 3rd digit G and 8th digit C
None/Glass Ceramic Alloy (Dual Seal Design with annunciator fitting) — Not available with 3rd digit G
None/Glass Ceramic Alloy —
Not available with 3rd digit G
D
N
11 | PROBE SIZE/ELEMENT TYPE/FLUSHING CONNECTION
0
None
12 | SPECIAL OPTIONS — See page 36
1
2
3
4
Single Length Removable Probe
2-piece Segmented Probe
3-piece Segmented Probe
4-piece Segmented Probe
13 14 15 | INSERTION LENGTH
cm (030 – 732)
inches (012 – 288)
XXX
unit of measure determined
by 2nd digit of model number
7
1
0
2
3
4
5
6
7
8
9
10
11
12
13
14
15
29
MODEL
SINGLE
NUMBER
ROD
RIGID
PROBE
1 | TECHNOLOGY
7
ECLIPSE GWR Probes - Model 706
2 | MEASUREMENT SYSTEM
A
C
English
Metric
3 | CONFIGURATION/STYLE (RIGID)
F
M
N
Single Rod, Standard (+400 °F/200 °C) for in-tank applications — NOT available with 10th digit N or D
Single Rod, High Pressure Probe with glass seal (+200 °C/+400 °F), for in-tank applications. Only available with 10 th Digit N or D
Single Rod, High Temp/High Pressure with glass seal (+450 °C/+850 °F), for in-tank applications. Only available with 10 th Digit N or D
4 5 | PROCESS CONNECTION – SIZE/TYPE (consult factory for other process connections) ¿
Threaded
1" NPT Thread ¡
21
22
1" BSP (G 1") Thread ¡
41
2" NPT Thread
42
ANSI Flanges
33
34
35
37
3K
3M
43
44
45
47
48
4K
4M
1 1⁄2" 150# ANSI RF ¿¬
1 1⁄2" 300# ANSI RF ¿¬
1 1⁄2" 600# ANSI RF ¿¬
1 1⁄2" 900/1500# ANSI RF √
1 1⁄2 600# ANSI RTJ √
1 1⁄2 900/1500# ANSI RTJ √
2" 150# ANSI RF ¿
2" 300# ANSI RF ¿
2" 600# ANSI RF ¿
2" 900/1500# ANSI RF √
2" 2500# ANSI RF √
2" 600# ANSI RTJ √
2" 900/1500# ANSI RTJ √
EN Flanges
CB
CC
CF
CG
DA
DB
DD
DE
DF
DG
DH
DJ
EA
EB
2"
3"
3"
3"
3"
3"
3"
3"
3"
3"
4N
53
54
55
56
57
58
5K
5L
5M
A ¿¬
B2 ¿¬
B2 ¿¬√
B2 ¿¬√
DN 40, PN 16/25/40
DN 40, PN 63/100
DN 40, PN 160
DN 40, PN 250
EN
EN
EN
EN
1092-1
1092-1
1092-1
1092-1
TYPE
TYPE
TYPE
TYPE
DN
DN
DN
DN
50,
50,
50,
50,
PN
PN
PN
PN
16
25/40
63
100
EN
EN
EN
EN
1092-1
1092-1
1092-1
1092-1
TYPE
TYPE
TYPE
TYPE
DN
DN
DN
DN
50,
50,
50,
50,
PN
PN
PN
PN
160
250
320
400
EN
EN
EN
EN
1092-1
1092-1
1092-1
1092-1
TYPE
TYPE
TYPE
TYPE
A¿
A¿
B2 ¿
B2 ¿
√
√
√
√
EN 1092-1 TYPE A ¿
B2
B2
B2
B2
DN 80, PN 16
DN 80, PN 25/40 EN 1092-1 TYPE A
¿
¡
¬
√
2" BSP (G 2") Thread
2500# ANSI RTJ √
150# ANSI RF
300# ANSI RF
600# ANSI RF
900# ANSI RF √
1500# ANSI RF √
2500# ANSI RF √
600# ANSI RTJ √
900# ANSI RTJ √
1500# ANSI RTJ √
ED
EE
EF
EG
EH
E J
FA
FB
FD
FE
FF
FG
FH
FJ
DN
DN
DN
DN
DN
DN
DN
DN
DN
DN
DN
DN
DN
DN
5N
63
64
65
66
67
68
6K
6L
6M
6N
3"
4"
4"
4"
4"
4"
4"
4"
4"
4"
4"
80, PN 63
80, PN 100
80, PN 160
80, PN 250
80, PN 320
80, PN 400
100, PN 16
100, PN 25/40
100, PN 63
100, PN 100
100, PN 160
100, PN 250
100, PN 320
100, PN 400
2500# ANSI RTJ √
150# ANSI RF
300# ANSI RF
600# ANSI RF
900# ANSI RF √
1500# ANSI RF √
2500# ANSI RF √
600# ANSI RTJ √
900# ANSI RTJ √
1500# ANSI RTJ √
2500# ANSI RTJ √
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1
2
3
4
5
6
7
8
9
B2
B2
B2 √
B2 √
B2 √
B2 √
A
A
B2
B2
B2 √
B2 √
B2 √
B2 √
Confirm mounting conditions/nozzle diameter to ensure sufficient clearance.
Not available with 3rd Digit N or 8th Digit P
Not available with 3rd digit ‘M’ or 'N'
Not available with 3rd digit ‘F’
7
30
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
10
11
12
13
14
15
MODEL
SINGLE
NUMBER
ROD
RIGID
CONTINUED
PROBE
6 | CONSTRUCTION CODES
0
Industrial
K
ASME B31.1
L
ASME B31.3
M
ASME B31.3 & NACE MR0175/MR0103 — NOT available with carbon steel flange
N
NACE MR0175/MR0103 — NOT available with carbon steel flange
7 | FLANGE OPTIONS
0
None
8 | MATERIAL OF CONSTRUCTION - MFG/NUT/ROD/INSULATION
A
316 SS/316L SS
B
Hastelloy C
C
Monel
F
Faced Flange, PFA coated wetted surfaces — Only available with Digit 3rd digit F
P
PFA coated rod — Only available with Digit 3rd digit F
R
316 SS/316L SS with Carbon Steel Flange
S
Hastelloy C with Carbon Steel Flange
T
Monel with Carbon Steel Flange
9 | SPACER MATERIAL
0
None – Not available with 3rd Digit N
2
PEEK HT (+345 °C/+650 °F) — Only available with 3rd digit N
3
Ceramic (High Temp.>+425 °C/+800 °F) — Only available with 3rd digit N
4
Celazole® (+425 °C/+800 °F) — Only available with 3rd digit N
10 | O-RING MATERIALS/SEAL OPTIONS
0
Viton® GFLT — Not available with 3rd digit M or N
2
Kalrez 4079 — Not available with 3rd digit M or N
8
Aegis PF 128 (NACE) — Not available with 3rd digit M or N
A
Kalrez 6375 — Not available with 3rd digit M or N
D
None/Glass Ceramic Alloy Dual Seal with annunciator
fitting — Not available with 3rd digit F
N
None/Glass Ceramic Alloy Dual Seal—Not available with 3rd digit F
11 | PROBE SIZE/ELEMENT TYPE/FLUSHING CONNECTION
0
Standard Single Rod
12 | SPECIAL OPTIONS
Non-Removable Rod—Only available with PFA Coated
Probes(8th digit F or P)
Removable Rod — Not available with PFA Coated
Probes(8th Digit F or P)
0
1
13 14 15 | INSERTION LENGTH
cm (030 – 732)
inches (012 – 288)
XXX
unit of measure determined
by 2nd digit of model number
7
1
0
2
3
4
5
6
7
0
8
9
10
11
12
13
14
15
31
MODEL
SINGLE
NUMBER
FLEXIBLE
PROBE
1 | TECHNOLOGY
7
ECLIPSE GWR Probes - Model 706
2 | MEASUREMENT SYSTEM
A
English
C
Metric
3 | SPECIALTY FLEXIBLE PROBES
1
Single Cable Flexible standard for in-tank applications (+200 °C/+400 °F)
2
Single Cable Flexible Light Duty Bulk Solids
3
Single Cable Flexible HP for in-tank applications (+200 °C/+400 °F)
6
Single Cable Flexible HTHP for chamber applications (+450 °C/+850 °F)
4 5 | PROCESS CONNECTION – SIZE/TYPE (consult factory for other process connections)
Threaded
41
2" NPT Thread
ANSI Flanges
43
44
45
47
48
4K
4M
4N
2"
2"
2"
2"
2"
2"
2"
2"
150# ANSI RF ¿
300# ANSI RF ¿
600# ANSI RF ¿
900/1500# ANSI RF
2500# ANSI RF
600# ANSI RTJ
900/1500# ANSI RTJ
2500# ANSI RTJ
EN Flanges
DA
DB
DD
DE
DF
DG
DH
DJ
EA
EB
ED
EE
42
DN 50, PN 16
DN 50, PN 25/40
DN 50, PN 63
DN 50, PN 100
DN 50, PN 160
DN 50, PN 250
DN 50, PN 320
DN 50, PN 400
DN 80, PN 16
DN 80, PN 25/40
DN 80, PN 63
DN 80, PN 100
53
54
55
56
57
58
5K
5L
5M
5N
3"
3"
3"
3"
3"
3"
3"
3"
3"
3"
2" BSP (G 2") Thread
150# ANSI RF
300# ANSI RF
600# ANSI RF
900# ANSI RF
1500# ANSI RF
2500# ANSI RF
600# ANSI RTJ
900# ANSI RTJ
1500# ANSI RTJ
2500# ANSI RTJ
EN 1092-1 TYPE A ¿
EN 1092-1 TYPE A ¿
EN 1092-1 TYPE B2 ¿
EN 1092-1 TYPE B2 ¿
EN 1092-1 TYPE B2 ¡
EN 1092-1 TYPE B2 ¡
EN 1092-1 TYPE B2 ¡
EN 1092-1 TYPE B2 ¡
EN 1092-1 TYPE A ¿
EN 1092-1 TYPE A
EN 1092-1 TYPE B2
EN 1092-1 TYPE B2
EF
EG
EH
E J
FA
FB
FD
FE
FF
FG
FH
FJ
DN
DN
DN
DN
DN
DN
DN
DN
DN
DN
DN
DN
63
64
65
66
67
68
6K
6L
6M
6N
4"
4"
4"
4"
4"
4"
4"
4"
4"
4"
80, PN 160
80, PN 250
80, PN 320
80, PN 400
100, PN 16
100, PN 25/40
100, PN 63
100, PN 100
100, PN 160
100, PN 250
100, PN 320
100, PN 400
150# ANSI RF
300# ANSI RF
600# ANSI RF
900# ANSI RF ¡
1500# ANSI RF ¡
2500# ANSI RF ¡
600# ANSI RTJ ¡
900# ANSI RTJ ¡
1500# ANSI RTJ ¡
2500# ANSI RTJ ¡
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
B2
B2
B2
B2
A
A
B2
B2
B2
B2
B2
B2
¡
¡
¡
¡
¡
¡
¡
¡
¿ Confirm mounting conditions/nozzle diameter to ensure sufficient clearance.
¡ Only available with 3rd Digit 3 or 6
7
1
32
2
3
4
5
6
7
8
9
10
11
12
13
14
15
MODEL
SINGLE
NUMBER
FLEXIBLE
CONTINUED
PROBE
6 | CONSTRUCTION CODES
0
Industrial
7 | FLANGE OPTIONS
0
None
8 | MATERIAL OF CONSTRUCTION - MFG/NUT/ROD/INSULATION
A
316 SS/316L SS
F
Faced Flange, PFA Coated Wetted Surfaces — Only available with 3rd digit 1
R
316 SS/316L SS with Carbon Steel Flange
9 | SPACER MATERIAL
0
None
4
Celazole® — Only available with 3rd digit 6
10 | O-RING MATERIALS/SEAL OPTIONS
0
Viton® GFLT
2
Kalrez 4079
8
Aegis PF 128 (NACE)
A
Kalrez 6375
N
None/Glass Ceramic Alloy Dual Seal — Only available with 3rd digit 6
11 | PROBE SIZE/ELEMENT TYPE/FLUSHING CONNECTION
3
Flexible Cable Probe
12 | SPECIAL OPTIONS
0
Non-removable Probe Cable
Only available with 3rd digit 2 or 8th digit F
1
Removable Single-piece Probe Cable
— Only available with 3rd digit 1, 3, 6
and 8th digit ≠ F
13 14 15 | INSERTION LENGTH
meters (001 – 030)
feet (003 – 100)
XXX
unit of measure determined
by 2nd digit of model number
7
1
2
3
4
5
0
0
6
7
0
8
9
3
10
11
12
13
14
15
33
MODEL
TWIN
NUMBER
FLEXIBLE
PROBE
1 | TECHNOLOGY
7
ECLIPSE GWR Probes - Model 706
2 | MEASUREMENT SYSTEM
A
English
C
Metric
3 | SPECIALTY FLEXIBLE PROBES
5
Twin Flexible Light Duty Bulk Solids with FEP Webbing
7
Twin Flexible - 316 SS with FEP Webbing
4 5 | PROCESS CONNECTION – SIZE/TYPE (consult factory for other process connections)
Threaded ¿
41
2" NPT Thread
42
2" BSP (G 2") Thread
ANSI Flanges
53
3"
150 lbs. ANSI RF
54
3"
300 lbs. ANSI RF
55
3"
600 lbs. ANSI RF
63
4"
150 lbs. ANSI RF
64
4"
300 lbs. ANSI RF
65
4"
600 lbs. ANSI RF
EN Flanges
EA
DN 80, PN 16
EN 1092-1 TYPE A
EB
DN 80, PN 25/40
EN 1092-1 TYPE A
ED
DN 80, PN 63
EN 1092-1 TYPE B2
EE
DN 80, PN 100
EN 1092-1 TYPE B2
FA
DN 100, PN 16
EN 1092-1 TYPE A
FB
DN 100, PN 25/40
EN 1092-1 TYPE A
FD
DN 100, PN 63
EN 1092-1 TYPE B2
FE
DN 100, PN 100
EN 1092-1 TYPE B2
¿ Confirm mounting conditions/nozzle diameter to ensure sufficient clearance.
7
1
34
2
3
4
5
6
7
8
9
10
11
12
13
14
15
MODEL
TWIN
NUMBER
FLEXIBLE
CONTINUED
PROBE
6 | CONSTRUCTION CODES
0
Industrial
7 | FLANGE OPTIONS
0
None
8 | MATERIAL OF CONSTRUCTION - MFG/NUT/ROD/INSULATION
A
316 SS/316L SS
R
316 SS/316L SS with Carbon Steel Flange
9 | SPACER MATERIAL
0
None
10 | O-RING MATERIALS/SEAL OPTIONS
0
Viton® GFLT
2
Kalrez 4079 – Only available with 3rd digit 7
8
Aegis PF 128 (NACE) – Only available with 3rd digit 7
A
Kalrez 6375 – Only available with 3rd digit 7
11 | PROBE SIZE/ELEMENT TYPE/FLUSHING CONNECTION
3
Flexible Cable Probe
12 | SPECIAL OPTIONS
0
None
13 14 15 | INSERTION LENGTH
meters (001 – 030)
feet (003 – 100)
XXX
unit of measure determined
by 2nd digit of model number
7
1
2
3
4
5
0
0
6
7
0
8
9
10
3
0
11
12
13
14
15
35
SEGMENTED
PROBE
12th
MODEL
DIGIT
OF
OPTIONS
NUMBER
Probe Model
One
Segment
Two
Segments
Three
Segments
Four
Segments
Five
Segments
Six
Segments
Coaxial Models
7yD, 7yP and 7yT
(Enlarged versions only)
(3", DN 80 Process
Connections and larger)
60 – 182 cm
(24 – 72")
120 – 365 cm
(48 – 144")
180 – 548 cm
(72 – 216")
240 – 731 cm
(96 – 288")
305 – 914 cm
(120 – 360")
365 – 999 cm
(144 – 396")
Caged Models
7yG, 7yL and 7yJ
30 – 305 cm
(12 – 120")
60 – 610 cm
(24 – 240")
90 – 732 cm
(36 – 288")
120 – 732 cm
(48 – 288")
Not Available
Not Available
NOTE: Segments will be evenly divided over the length of the probe.
36
COAXIAL
mm
PROBE
DIMENSIONS
(INCHES)
86
(3.38)
86
(3.38)
106
(4.18)
96
(3.77)
86
(3.38)
106
(4.18)
96
(3.77)
96
(3.77)
236
(9.30)
2 cable
entries
45 °
Optional
flushing port
1/4" NPT
113
(4.46)
Mounting
flange
236
(9.30)
236
(9.30)
45 °
2 cable
entries
76 (3.0)
typical
106
(4.18)
45 °
2 cable
entries
Optional
flushing port
1/4" NPT
Optional
flushing port
1/4" NPT
197
(7.76)
265
(10.45)
76 (3.0)
typical
76 (3.0)
typical
Probe
insertion
length
Mounting
flange
Probe
insertion
length
Model 7yT
with flanged connection
86
(3.38)
Mounting
flange
Model 7yP
with flanged connection
106
(4.18)
Model 7yD
with flanged connection
F
96
(3.77)
B
236
(9.30)
C
A
2 cable
entries
Probe
insertion
length
E
Model 7yS
Coaxial GWR Probe,
End View
45 °
Ø 63,5
(2.5)
A
D
B
293
(11.55)
Coaxial GWR Probe,
End View
Coaxial Probe Slots
mm (inches)
Dim.
Mounting
flange
Probe
insertion
length
Model 7yS
with flanged connection
Small Diameter
Segmented Enlarged
Coaxial Probe
Enlarged (standard)
A
22,5 (0.88)
45 (1.75) - SST
49 (1.92) - HC and Monel
B
C
D
E
8 (0.31)
100 (4.08)
4 (0.15)
96 (3.78)
16 (0.63)
153 (6.05)
8 (0.30)
138 (5.45)
F
31,75 (1.25)
—
37
CAGED
mm
PROBE
DIMENSIONS
(INCHES)
86
(3.38)
86
(3.38)
106
(4.18)
86
(3.38)
96
(3.77)
106
(4.18)
106
(4.18)
96
(3.77)
96
(3.77)
236
(9.30)
236
(9.30)
236
(9.30)
45 °
2 cable
entries
45 °
2 cable
entries
45 °
2 cable
entries
119
(4.70)
Mounting
flange
D
Mounting
flange
Probe
insertion
length
D
L
L
Model 7yG
with flanged connection
38
265
(10.45)
162
(6.39)
Mounting
flange
Probe
insertion
length
Model 7yL
with flanged connection
D
L
Probe
insertion
length
Model 7yJ
with flanged connection
Cage Size
Probe Rod Diameter (D)
Spacer Length (L)
2"
13 to 19 mm (0.5 to 0.75")
46 mm (1.82")
3"
19 to 29 mm (0.75 to 1.13")
67 mm (2.64")
4"
27 to 38 mm (1.05 to 1.50")
91 mm (3.60")
SINGLE
mm
ROD
RIGID
PROBE
DIMENSIONS
(INCHES)
86
(3.38)
86
(3.38)
86
(3.38)
106
(4.18)
106
(4.18)
106
(4.18)
96
(3.77)
96
(3.77)
96
(3.77)
236
(9.30)
236
(9.30)
236
(9.30)
45 °
2 cable
entries
45 °
2 cable
entries
45 °
2 cable
entries
115
(4.53)
Mounting
flange
265
(10.45)
213
(8.38)
Ø 9,6
(0.38)
Model 7yF
with flanged connection
Probe
insertion
length
Mounting
flange
Mounting
flange
Ø 9,6
(0.38)
Probe
insertion
length
Model 7yM
with flanged connection
Ø 13
(0.50)
34
(1.33)
Probe
insertion
length
Model 7yN
with flanged connection
39
SINGLE
mm
FLEXIBLE
PROBE
(INCHES)
86
(3.38)
DIMENSIONS
86
(3.38)
106
(4.18)
86
(3.38)
106
(4.18)
106
(4.18)
96
(3.77)
96
(3.77)
96
(3.77)
236
(9.30)
236
(9.30)
236
(9.30)
2 cable
entries
45 °
2 cable
entries
45 °
45 °
2 cable
entries
115
(4.53)
Mounting
flange
265
(10.45)
265
(10.45)
Mounting
flange
Mounting
flange
Probe
insertion
length
Ø 51 (2)
Ø 0,5 (0.19)
Ø 51 (2)
Ø 51 (2)
99
(3.88)
Probe
insertion
length
Probe
insertion
length
19 (0.75)
Model 7y3
with flanged
connection
Model 7y1
with flanged connection
86
(3.38)
Model 7y6
with flanged
connection
152
(6)
106
(4.18)
96
(3.77)
236
(9.30)
45 °
2 cable
entries
Ø 51 (2)
152
(6)
139
(5.46)
Mounting
flange
Ø 51 (2)
Probe
insertion
length
Model 7y2
with flanged
connection
40
152
(6)
7y2: SST weight
2,25 kg (5 lbs.)
order code: 004-8778-001
+ 2 x 010-1731-001
152
(6)
“IN
TANK”
MOUNTING
STANDARD
SINGLE
ROD
PROBE
CONSIDERATIONS
For Rigid Models 7yF, M, N and Flexible Models 7y1,
2 and 6
1. Turbulence
The bottom of rigid probes should be stabilized if
turbulence will cause a deflection of more than
75 mm (3") at the end of a 3 m (10') length. The probe
should not make contact with metal.
2. Nozzle
3. Metallic (conductive) obstructions in tank.
Although it depends on the transmitter configuration,
objects in the proximity of the probe can cause erroneous readings. Please refer to the table below for
guidelines, but please contact the factory with any
questions as the distances shown can be reduced with
the use of PACTware™.
Distance to probe
Acceptable objects
< 150 mm (6")
Continuous, smooth, parallel,
conductive surface (e.g. metal
tank wall); probe should not
touch tank wall
> 150 mm (6")
< 1"/DN25 diameter pipe and
beams, ladder rungs
> 300 mm (12")
< 3"/DN80 diameter pipe and
beams, concrete walls
> 450 mm (18")
All remaining objects
Single rod performance in nozzles can be improved
by ensuring the following:
• Nozzle must be 50 mm (2") or larger diameter.
• Nozzle should be as short as possible.
• Nozzle inside diameter (A) should be ≥ to nozzle
height (B).
• If this is not the case, adjustments to
BLOCKING DISTANCE and/or SENSITIVITY
parameters may be required.
Note: A metal stillwell/cage of max. 6"/DN150
size or a metal tank wall parallel to the
probe within 150 mm (6") will allow the
unit to operate accurately in media with dielectrics down to εr 1.4.
4. Non-metallic vessels
A
B
A metal flange is highly recommended for optimum
performance in plastic vessels.
NOTE: Singe rod probes must be used in metallic
vessels or stillwell to maintain CE noise immunity.
Shutdown /Overfill protection
Correct Installation
Special consideration is necessary in any shutdown/
overfill protection application where single rod GWR
probes are used. To ensure proper measurement, use
Overfill Capable single rod probes, such as the Model
7yG, L, or J Caged probes in the appropriate cage/
chamber/stillwell.
Mounting Considerations for Single Flexible probes
measuring Bulk Solids
The Model 7y2 Bulk Solid probe is designed for a 1360 kg
(3000 lb.) pull-down force for use in applications such as
sand, plastic pellets, and grains.
Pipe reducers
should not be used
• To reduce excessive stresses on the top of the
vessel, do not secure the metal probe weight to the
bottom of the vessel.
• Mount the probe at least 300 mm (12") from the
wall. The ideal location is 1⁄4 to 1⁄2 the diameter to average the angle of repose.
41
TWIN
mm
FLEXIBLE
PROBE
(INCHES)
DIMENSIONS
86
(3.38)
106
(4.18)
86
(3.38)
96
(3.77)
236
(9.30)
106
(4.18)
96
(3.77)
152
(6)
Ø 51 (2)
236
(9.30)
2 cable
entries
45 °
2 cable
entries
45 °
135
(5.31)
Mounting
flange
7y5: SST weight
2,25 kg (5 lbs.)
order code: 004-8778-002
+ 2 x 010-1731-001
115
(4.54)
Mounting
flange
Probe
insertion
length
Probe
insertion
length
22,2 (0.875)
Ø 13 (0.50) Rods
6,3 (0.248)
Model 7y5
with flanged connection
Twin Flexible GWR Probe
end view
“IN
TANK”
MOUNTING
TWIN
FLEXIBLE
PROBE
CONSIDERATIONS
For Models 7y7
1. Turbulence
The bottom of Twin Flexible probes can be secured
to the bottom of the vessel by using the TFE weight
at the bottom of the probe. The TFE weight has a
13 mm (1⁄2") hole that can be utilize to “u-bolt” the
probe to the bottom of the vessel.
The probe should not make contact with metal.
2. Nozzle
Twin Flexible probe performance in nozzles can be
improved by ensuring the following:
• Nozzle should be 3" (DN80) diameter or larger.
• Nozzle should be as short as possible.
42
Model 7y7
with flanged connection
3. Metallic (conductive) obstructions in tank.
Mount the Twin Flexible probe more than 25 mm (1")
from any metallic object/vessel wall.
Mounting Considerations for Twin Flexible Model 7y5
probes measuring Bulk Solids:
The Model 7y5 Bulk Solid probe is designed for a 1360 kg
(3000 lb.) pull-down force for use in applications such as
sand, plastic pellets, and grains.
• To reduce excessive stresses on the top of the
vessel, do not secure the metal probe weight to the
bottom of the vessel.
• Mount the probe at least 300 mm (12") from the
wall. The ideal location is 1⁄4 to 1⁄2 the diameter to average the angle of repose.
AURORA
®
CHAMBER
The Orion Instruments® Aurora® is the patented combination of the ECLIPSE Guided Wave Radar transmitter and
a Magnetic Level Indicator (MLI). The integration of these
two independent technologies provides excellent redundancy. A custom float positioned within the AURORA
chamber travels up and down following level changes.
The float contains an internal group of magnets that are
“coupled” with magnets in the flags of the visual indicator mounted on the outside of the chamber. As the float
moves, the flags rotate to expose the color of their opposite side. The position where the flag’s color changes corresponds to a point on the measuring scale indicating true
level. In addition to this external visual indicator operated by the AURORA internal float, the ECLIPSE
Model 706 transmitter reflects electromagnetic radar pulses
directly off the liquid surface providing a real-time continuous level output.
Visual
Visual
Indication
Indication
Range
Range
Center
Center
to
to
Center
Center
Visual
Visual
Indication
Indication
Range
Range
Refer to the Magnetrol® Sales Bulletin BE 57-138 for details and additional options on AURORA chambers.
Regardless of whether a standard chamber or AURORA
chamber is being used it is important to remember:
• Ensure that the Model 706 probe extends at least
100 mm (4") past the lower process connection of
the chamber
• Utilize Overfill-capable probes for optimal GWR
performance.
Center
Center
to
Center
Center
Visual
Visual
Indication
Indication
Range
Range
Center
Center
to
to
Center
Center
43
QUALITY ASSURANCE - ISO 9001:2008
THE QUALITY ASSURANCE SYSTEM IN PLACE AT MAGNETROL GUARANTEES THE HIGHEST LEVEL OF QUALITY DURING THE DESIGN,
THE CONSTRUCTION AND THE SERVICE OF CONTROLS.
OUR QUALITY ASSURANCE SYSTEM IS APPROVED AND CERTIFIED TO ISO 9001:2008 AND OUR TOTAL COMPANY IS COMMITTED TO
PROVIDING FULL CUSTOMER SATISFACTION BOTH IN QUALITY PRODUCTS AND QUALITY SERVICE.
PRODUCT WARRANTY
:2008
ALL MAGNETROL ELECTRONIC AND ULTRASONIC LEVEL CONTROLS ARE WARRANTED FREE OF DEFECTS IN MATERIALS AND WORKMANSHIP FOR ONE FULL YEAR FROM THE DATE OF ORIGINAL FACTORY SHIPMENT. IF RETURNED WITHIN THE WARRANTY PERIOD; AND, UPON FACTORY INSPECTION
OF THE CONTROL, THE CAUSE OF THE CLAIM IS DETERMINED TO BE COVERED UNDER THE WARRANTY; THEN, MAGNETROL INTERNATIONAL WILL REPAIR OR REPLACE THE CONTROL AT NO COST TO THE PURCHASER (OR OWNER) OTHER THAN TRANSPORTATION.
MAGNETROL SHALL NOT BE LIABLE FOR MISAPPLICATION, LABOR CLAIMS, DIRECT OR CONSEQUENTIAL DAMAGE OR EXPENSE ARISING FROM THE INSTALLATION OR
USE OF THE EQUIPMENT. THERE ARE NO OTHER WARRANTIES EXPRESSED OR IMPLIED, EXCEPT, SPECIAL WRITTEN WARRANTIES COVERING SOME MAGNETROL
PRODUCTS.
BULLETIN N°:
EFFECTIVE:
SUPERSEDES:
UNDER RESERVE OF MODIFICATIONS
Heikensstraat 6, 9240 Zele, België -Belgique
Tel. +32 (0)52.45.11.11 • Fax. +32 (0)52.45.09.93 • E-Mail: [email protected]
DEUTSCHLAND
Alte Ziegelei 2-4, D-51491 Overath
Tel. +49 (0)2204 / 9536-0 • Fax. +49 (0)2204 / 9536-53 • E-Mail: [email protected]
INDIA
B-506, Sagar Tech Plaza, Saki Naka Junction, Andheri (E), Mumbai - 400072
Tel. +91 22 2850 7903 • Fax. +91 22 2850 7904 • E-Mail: [email protected]
ITALIA
Via Arese 12, I-20159 Milano
Tel. +39 02 607.22.98 • Fax. +39 02 668.66.52 • E-Mail: [email protected]
RUSSIA
198095 Saint-Petersburg, Marshala Govorova street, house 35A, office 427
Tel. +7 812 320 70 87 • E-Mail: [email protected]
U.A.E.
UNITED
KINGDOM
DAFZA Office 5EA 722 • PO Box 293671 • Dubai
Tel. +971-4-6091735 • Fax +971-4-6091736 • E-Mail: [email protected]
Unit 1 Regent Business Centre, Jubilee Road Burgess Hill West Sussex RH 15 9TL
Tel. +44 (0)1444 871313 • Fax +44 (0)1444 871317 • E-Mail: [email protected]
www.magnetrol.com
BENELUX
FRANCE
OUR NEAREST REPRESENTATIVE
BE 57-106.4
APRIL 2016
May 2014