AD ADF7901BRU-REEL

High Performance ISM Band
OOK/FSK Transmitter IC
ADF7901
FEATURES
GENERAL DESCRIPTION
Single-chip, low power UHF transmitter
369.5 MHz to 395.9 MHz frequency operation using
fractional-N PLL and fully integrated VCO
3.0 V supply voltage
Data rates up to 50 kbps supported
Low current consumption
26 mA at 12 dBm output at 384 MHz
Power-down mode (<1 μA)
24-lead TSSOP
The ADF7901 is a low power OOK/FSK UHF transmitter
designed for use in RF remote control devices. It is capable of
frequency shift keying (FSK) modulation on eight different
channels, selectable by three external control lines. OOK
modulation is performed by modulating the PA control line.
The on-chip VCO operates at 2× the output frequency. The
division by 2 at the output of the VCO reduces the amount of
PA feedthrough. As a result, OOK modulation depths of greater
than 50 dB are easily achievable.
The FSK_ADJ and ASK_ADJ resistors can be adjusted in the
system to optimize output power for each modulation scheme.
An additional 1.5 dB of output power is provided for the lower
bank of channels to adjust for antenna performance. The CE
line allows the transmitter to be powered down completely.
In this mode, the leakage current is typically 0.1 μA.
FUNCTIONAL BLOCK DIAGRAM
CREG2
OSC1
PA_EN
OSC2
CVCO
VDD
VCO
RFOUT
PA
R=1
RFGND
PDF
CHARGE
PUMP
LDO
REGULATOR
1
⎟ FRACTIONAL N
TXDATA
LDO
REGULATOR
2
Σ-Δ
FSK
CHANNEL SELECT
CE
DGND
FSK1 FSK2 FSK3
CREG1
CREG2
RSET
OOK_SEL
RSET_FSK
RSET_OOK
05349-001
DVDD
Figure 1.
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2006 Analog Devices, Inc. All rights reserved.
ADF7901
TABLE OF CONTENTS
Features .............................................................................................. 1
Channel Frequencies.....................................................................9
General Description ......................................................................... 1
Layout Guidelines....................................................................... 10
Functional Block Diagram .............................................................. 1
Decoupling.............................................................................. 10
Specifications..................................................................................... 3
Regulator Stability .................................................................. 10
Absolute Maximum Ratings............................................................ 5
Grounding............................................................................... 10
ESD Caution.................................................................................. 5
Supply ...................................................................................... 10
Pin Configuration and Function Descriptions............................. 6
Digital Lines............................................................................ 10
Typical Performance Characteristics ............................................. 8
Outline Dimensions ....................................................................... 11
Circuit Description........................................................................... 9
Ordering Guide .......................................................................... 11
Loop Filter ..................................................................................... 9
REVISION HISTORY
3/06—Rev. 0 to Rev. A
Added Crystal ESR Parameter ........................................................ 4
Change to Figure 8 ......................................................................... 10
Updated Outline Dimensions ....................................................... 11
Changes to Ordering Guide .......................................................... 11
3/05—Revision 0: Initial Version
Rev. A | Page 2 of 12
ADF7901
SPECIFICATIONS
VDD =3.0 V; GND = 0 V; TA = TMIN to TMAX, unless otherwise noted. Typical specifications, TA = 25°C. 1
Table 1.
Parameter
RF CHARACTERISTICS
Output Frequency Ranges
Channel 1
Channel 2
Channel 3
Channel 4
Channel 5
Channel 6
Channel 7
Channel 8
Channel 9
Phase Frequency Detector Frequency
TRANSMISSION PARAMETERS
Transmit Rate
FSK
OOK
Frequency Shift Keying
FSK Separation 2
On/Off Keying
Modulation Depth 3
Output Power
Min/Max Range 4
fOUT ≤ 384 MHz
fOUT > 384 MHz
Occupied 20 dB BW
OOK at 1 kbps
FSK (PA Off/On) at10 Hz 5
LOGIC INPUTS
VINH, Input High Voltage
VINL, Input Low Voltage
IINH/IINL, Input Current
CIN, Input Capacitance
POWER SUPPLIES
Voltage Supply
DVDD
Transmit Current Consumption
369.5 MHz to 376.9 MHz at 12 dBm
384 MHz at +12 dBm
388.3 MHz to 395.9 MHz at 10.5 dBm
384 MHz at 5 dBm
Power-Down Mode
Low Power Sleep Mode 6
Min
10
7
Typ
Max
Unit
Comments/Conditions
369.5
371.1
375.3
376.9
384.0
388.3
391.5
394.3
395.9
9.8304
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
50
50
kbps
kbps
−34.8
+34.8
kHz
kHz
Data = 1
Data = 0
83
dB
Output power = 12 dBm
15
12
10.5
dBm
dBm
dBm
±28
±26
±461.9
±461.9
kHz
kHz
0.2 × VDD
±1
10
V
V
μA
pF
2.124
3.0
V
26
26
21
17
mA
mA
mA
mA
0.2
Rev. A| Page 3 of 12
1
μA
ADF7901
Parameter
PHASE-LOCKED LOOP
VCO Gain
Spurious3, 7
Integer Boundary
Reference
Harmonics3
Second Harmonic VDD = 3.0 V
Third Harmonic VDD = 3.0 V
All Other Harmonics
REFERENCE INPUT
Crystal Reference
Crystal ESR 8
POWER AMPLIFIER
PA Output Impedance
TIMING INFORMATION
Crystal Oscillator to PLL Lock3
PA Enable to PA Ready–PLL Settle 9
TEMPERATURE RANGE (TA)
Min
Typ
Max
30
Unit
Comments/Conditions
MHz/V
At 384 MHz
100 kHz loop BW
–45
−70
−23
−23
dBc
dBc
−24
−14
−21
−11
−18
dBc
dBc
dBc
80
MHz
Ω
9.8304
97 Ω + 6.4 pF
2
100
0
At 384 MHz
3
250
50
ms
μs
°C
1 Operating temperature range is 0°C to 50°C.
2
Frequency Deviation = 58 × (9.8304 MHz)/214. Error in the crystal is reflected in variation in the desired deviation.
3
Not production tested; based on characterization.
4
The output power can be varied in both ASK/FSK mode by altering the relevant external resistor.
5
Measured using spectrum analyzer, 1 MHz span, 100 kHz RBW, maximum hold enabled.
6
Maximum power-down current specification applies for the OSC2 pin grounded.
7
Measured >461.9 kHz away from channel.
8
Maximum recommended crystal ESR. The crystal oscillator works with crystals with higher ESR, but this results in longer power-up times.
9
This specification refers to the time taken for the PLL to regain lock after the PA has been enabled. The PA is should only be enabled after the PLL has settled to the
correct frequency.
Rev. A | Page 4 of 12
ADF7901
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted. 1
Table 2.
Parameter
VDD to GND 2
RFVDD to GND
Digital I/O Voltage to GND
Operating Temperature Range
Industrial (B Version)
Storage Temperature Range
Maximum Junction Temperature
TSSOP θJA Thermal Impedance
Lead Temperature, Soldering
Vapor Phase (60 sec)
Infrared (15 sec)
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those listed in the operational sections
of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Value
−0.3 V to +4.0 V
−0.3 V to +4.0 V
−0.3 V to VDD + 0.3 V
0°C to 50°C
−65°C to +125°C
125°C
150.4°C/W
235°C
240°C
1
This device is a high performance, RF-integrated circuit with an ESD rating
of <1 kV. It is ESD sensitive. Take proper precautions for handling and
assembly.
2
GND = RFGND = DGND = 0 V.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the
human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. A| Page 5 of 12
ADF7901
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
DVDD
1
24
CREG2
CREG1
2
23
RSET
CPOUT
3
22 PA_EN
TxDATA
4
DGND
5
NC
6
DGND
7
OSC1
8
17 CVCO
OSC2
9
16
OOK_SEL 10
15
RSET_OOK
FSK1 11
14
CE
FSK2 12
13 FSK3
21 DVDD
TOP VIEW
(Not to Scale)
20 RFOUT
19
RFGND
18
VCOIN
RSET_FSK
05349-002
ADF7901
Figure 2. Pin Configuration
Table 3. Pin Function Descriptions
Pin No.
1
Mnemonic
DVDD
2
CREG1
3
CPOUT
4
5
6
7
8
TxDATA
DGND
NC
DGND
OSC1
9
OSC2
10
11
12
13
14
15
OOK_SEL
FSK1
FSK2
FSK3
CE
RSET_OOK
16
RSET_FSK
17
CVCO
18
VCOIN
19
20
RFGND
RFOUT
Function
Positive Supply for the Digital Circuitry. This must be 3.0 V. Decoupling capacitors to the analog ground plane
should be placed as close as possible to this pin.
A 2.2 μF capacitor should be added at CREG1 to reduce regulator noise and improve stability. A reduced capacitor
improves regulator power-on time but can cause higher spurious.
Charge Pump Output. This output generates current pulses that are integrated in the loop filter. The integrated
current changes the control voltage on the input to the VCO.
Digital FSK data to be transmitted is inputted on this pin.
Ground for Digital Section.
No Connect.
Ground for Digital Section.
The reference crystal should be connected between this pin and the OSC2 pin. The necessary crystal load
capacitor should be tied between this pin and ground.
The reference crystal should be connected between this pin and the OSC1 pin. The necessary crystal load
capacitor should be tied between this pin and ground.
A TCXO or external square wave can also be connected to this pin, with OSC1 left floating. A DC-blocking
capacitor (4.7 nF is adequate) should be placed between the TCXO output and OSC2 pin.
When not using an external regulator, a 1 MΩ resistor can be tied between the OSC2 pin and ground to meet the
power-down current specification of 1 μA.
A high on this pin selects operation in OOK mode at 384 MHz when CE is high.
FSK Channel Select Pin. This represents the LSB of the channel select pins.
FSK Channel Select Pin.
FSK Channel Select Pin.
Bringing CE low puts the ADF7901 into power-down, drawing <1 μA of current.
The value of this resistor sets the output power for data = 1 in OOK mode. A resistor of 3.6 kΩ provides the
maximum output power. Increasing the resistor reduces the power and the current consumption. A lower resistor
value than 3.6 kΩ can be used to increase the power to a maximum of 14 dBm. The PA does not operate efficiently
in this mode.
The value of this resistor sets the output power in FSK mode. A resistor of 3.6 kΩ provides maximum output
power. Increasing the resistor reduces the power and the current consumption. A resistor value lower than 3.6 kΩ
can be used to increase the power to a maximum of 14 dBm. The PA does not operate efficiently in this mode.
A 22 nF capacitor should be tied between the CVCO and CREG2 pins. This line should run underneath the ADF7901.
The capacitor is necessary to ensure stable VCO operation.
The tuning voltage on this pin determines the output frequency of the voltage controlled oscillator (VCO).
The higher the tuning voltage the higher the output frequency. The output of the loop filter is connected here.
Ground for Output Stage of Transmitter.
The modulated signal is available at this pin. Output power levels are from –5 dBm to +12 dBm. The output
should be impedance matched using suitable components to the desired load.
Rev. A | Page 6 of 12
ADF7901
Pin No.
21
Mnemonic
DVDD
22
PA_EN
23
24
RSET
CREG2
Function
Voltage Supply for VCO and PA Section. It should be supplied with 3.0 V. Decoupling capacitors to the ground
plane should be placed as close as possible to this pin.
This pin is used to enable the power amplifier. It should be modulated with the OOK data in OOK mode. In
FSK mode, it should be enabled when the PLL is locked.
External Resistor. Sets charge pump current and some internal bias currents. Use 3.6 kΩ as default.
A 2.2 μF capacitor should be added at CREG2 to reduce regulator noise and improve stability. A reduced capacitor
improves regulator power-on time but can cause higher spurs.
Rev. A| Page 7 of 12
ADF7901
TYPICAL PERFORMANCE CHARACTERISTICS
Ref 15dBm
Avg
Log
10
dB/
OUTPUT POWER (dBm)
16
Mkr1 10.00kHz
Noise –89.55dB/Hz
Atten 30dB
1R
12
RBW
300.0000000Hz
8
PAvg
1
W1 S2
S3 FS
AA
4
2
3
4
5
6
RSET
7
8
9
10
Center 395.948 29MHz
#Res BW 300Hz
Span 50kHz
Sweep 2.118 s (601 pts)
VBW 300Hz
05349-006
0
05349-004
£(f):
f<50k
Swp
Figure 5. Phase Noise at Channel 9
Figure 3. Output Power vs. RSET FSK, Upper FSK Channels,
Measured into 50 Ω
Ref 15dBm
Peak
Log
10
4R
dB/
2
35
4
30
Mkr4 1.59GHz
–21.30dB
Atten 30dB
1
Marker Trace Type
1
(1)
Freq
2
(1)
Freq
3
(1)
Freq
4
(1)
Freq
X Axis
400MHz
800MHz
1.19GHz
1.59GHz
Amplitude
–25.56dB
–13.89dB
–34.53dB
–21.30dB
IDD (mA)
3
25
20
15
5
6
7
8
OUTPUT POWER (dBm)
9
10
Figure 4. Current Consumption vs. Output Power, Upper FSK Channels,
Measured into 50 Ω
Rev. A | Page 8 of 12
Center 5.50GHz
#Res BW 1MHz
VBW 1MHz
Span 10.5GHz
Sweep 17.52 ms (601 pts)
Figure 6. Harmonic Levels—Up to Fourth Harmonic,
Measured at Channel 9 into 50 Ω
05349-007
4
05349-005
LgAv
10
ADF7901
CIRCUIT DESCRIPTION
Table 4.
Frequency (MHz)
369.5
371.1
375.3
376.9
384.0
388.3
391.5
394.3
395.9
FSK3
0
0
0
0
Don’t
care
1
1
1
1
FSK2
0
0
1
1
Don’t
care
0
0
1
1
FSK1
0
1
0
0
Don’t
care
0
1
0
1
OOK_SEL
0
0
0
0
1
CHANNEL FREQUENCIES
The nine channel frequencies listed in Table 4 are obtainable
from a single 9.8304 MHz crystal reference by changing the
value of the N and F numbers in the fractional PLL, using
control lines FSK1, FSK2, and FSK3. The channel frequency is
given by
FCHANNEL = FREF × (N + F)
0
0
0
0
LOOP FILTER
The loop filter integrates the current pulses from the charge
pump to form a voltage that tunes the output of the VCO to the
desired frequency. It also attenuates spurious levels generated by
the PLL. The recommended loop filter design for this circuit is
297 kHz. This is based on the trade-off between attenuation of
beat note spurs and the need to minimize chirp when the PA is
turned on.
However, the VCO is tuned to operate over a frequency range
of 344 MHz to 401 MHz (typically). Therefore, any channel
frequency within this range can be obtained if the required
reference frequency is used. The N and F numbers for each
channel are listed in Table 5, together with the corresponding
channel frequencies for 9.8304 MHz and, for example purposes,
frequencies for 10 MHz. With the 10 MHz reference, the two
largest N settings give channel frequencies above the maximum
VCO output frequency and are therefore invalid.
Frequency deviation is also dependent on reference frequency.
The relationship is given by
FDEV = 58 × (9.8304 MHz)/214
Therefore, the frequency deviation is 34.8 kHz when the
9.8304 MHz reference is used and 35.4 kHz when the 10 MHz
reference is used.
R2 = 6.2kΩ
CHARGE
PUMP OUT
VCO
C1 = 33pF
C2 = 390pF
C3 = 10pF
05349-008
R1 = 3kΩ
Figure 7.
Improved spurious performance in FSK mode can be achieved
by using a narrower loop bandwidth. For a data rate of 20 kbps,
a loop bandwidth of roughly 50 kHz would be suitable. The
following components give a loop bandwidth of 51.1 kHz:
C1 = 680 pF
C2 = 15 nF
C3 = 180 pF
Table 5.
N
37
37
38
38
39
39
39
40
40
R1 = 510 Ω
R2 = 6.2 kΩ
ADIsimPLL is a free software tool offered by Analog Devices
for assistance in designing with ADI’s frequency synthesizers
and ISM band transmitters. To select the correct loop filter
components for use with the ADF7901, open a project for the
ADF7012 device. Then, enter the desired output carrier
frequency and loop bandwidth, and use the 870 μA charge
pump current setting.
ADIsimPLL can be downloaded from www.analog.com.
Rev. A| Page 9 of 12
F
2406/4096
3073/4096
727/4096
1374/4096
256/4096
2048/4096
3381/4096
452/4096
1118/4096
Channel Frequency (MHz)
9.8304 MHz Ref 10 MHz Ref
369.5
375.9
371.1
377.5
375.3
381.8
376.9
383.4
384.0
390.6
388.3
395
391.5
398.3
394.3
N/A
395.9
N/A
ADF7901
22nF
2.2μF
2.2μF
MATCHING RFOUT TO 50Ω
CVCO CREG2
DVDD
CREG1
RSET
27nH
5TH-ORDER, LOW-PASS FILTER
3.6kΩ
22nH
5.6pF
1.5pF
22nH
RFOUT
VCOIN
CPOUT
ANTENNA
3pF
VCOIN
8pF
3pF
ADF7901
36nH
MATCHING 50Ω
TO ANTENNA
RSET_FSK
3.6kΩ
RSET_OOK
3.6kΩ
FSK1
FSK2
OSC2
FSK3
OOK_SEL
9.8304MHz
OSC1
PA_EN
CE
33pF
33pF
GND
NOTES
1. DECOUPLING CAPACITORS HAVE
BEEN OMITTED FOR CLARITY.
05349-003
TxDATA
Figure 8. Applications Diagram for the ADF7901 in a Remote Control System
LAYOUT GUIDELINES
Grounding
The layout of the board is crucial to ensuring low levels of
spurious and harmonics.
Emphasis should be placed on grounding once the decoupling
capacitors have been added. The PA stage switches currents of
15 mA in maximum power mode. This causes changes in the
ground resulting in large return currents that can radiate to
other parts of the board. The shortest and least obstructed
ground from RFGND back to the ground of the battery should be
ensured. A 4-layer board helps, as well as flooding the top layer.
The ground paths should not have any vias and should be wide
tracks.
Decoupling
Decoupling capacitors (high frequency 22 pF, low frequency
100 nF) should be placed as close as possible to the supply pins
on the part. Low size 0402 and 0603 components are recommended for the high frequency rejection on the supply.
Regulator Stability
A minimum of 1 μF is needed on both CREG1 and CREG2 to ensure
stability. An additional 22 pF capacitor can be added to reject
higher frequency noise. Because many of the internal blocks
run off the regulator, it is critical to reduce its noise. Low size
0402 and 0603 components are recommended for the high
frequency rejection on the supply.
Supply
The supply tracks can be routed through vias, because they act
as free inductors and make layout easier on a 2-layer board
(see the Decoupling section). Tracks should be wide.
Digital Lines
Digital lines should contain a large resistor in series. This
impedance blocks signals of many frequencies, including
harmonics and the carrier frequency. Long control lines can
act as antennae. It can be useful to add capacitance to ground.
There is some capacitance to ground provided by the lines and
at the input of the digital pins.
Rev. A | Page 10 of 12
ADF7901
OUTLINE DIMENSIONS
7.90
7.80
7.70
24
13
4.50
4.40
4.30
6.40 BSC
1
12
PIN 1
0.65
BSC
0.15
0.05
0.30
0.19
1.20
MAX
SEATING
PLANE
0.20
0.09
8°
0°
0.75
0.60
0.45
0.10 COPLANARITY
COMPLIANT TO JEDEC STANDARDS MO-153AD
Figure 9. 24-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-24)
Dimensions shown in millimeters
ORDERING GUIDE
Model
ADF7901BRU
ADF7901BRU-REEL
ADF7901BRU-REEL7
ADF7901BRUZ 1
ADF7901BRUZ-RL1
ADF7901BRUZ-RL71
EVAL-ADF7901EB
1
Temperature Range
0°C to 50°C
0°C to 50°C
0°C to 50°C
0°C to 50°C
0°C to 50°C
0°C to 50°C
Package Description
24-Lead Thin Shrink Small Outline Package (TSSOP)
24-Lead Thin Shrink Small Outline Package (TSSOP)
24-Lead Thin Shrink Small Outline Package (TSSOP)
24-Lead Thin Shrink Small Outline Package (TSSOP)
24-Lead Thin Shrink Small Outline Package (TSSOP)
24-Lead Thin Shrink Small Outline Package (TSSOP)
Evaluation Board
Z = Pb-free part.
Rev. A| Page 11 of 12
Package Option
RU-24
RU-24
RU-24
RU-24
RU-24
RU-24
ADF7901
NOTES
©2006 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D05349-0-3/06(A)
Rev. A | Page 12 of 12