INCH-POUND MIL-PRF-28861/1D w/AMENDMENT 1 10 May 2005_ SUPERSEDING MIL-PRF-28861/1D 10 February 2003 PERFORMANCE SPECIFICATION SHEET FILTERS AND CAPACITORS, RADIO FREQUENCY/ELECTROMAGNETIC INTERFERENCE SUPPRESSION, HERMETICALLY SEALED, STYLES FS10 AND FS11 This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-28861. * FIGURE 1. Case and hardware dimensions and circuit diagrams. AMSC N/A FSC 59GP MIL-PRF-28861/1D w/AMENDMENT 1 * Dash number 001 through 010 and 021 through 026 011 through 020 and 031 through 036 A dimension (±.010) .187 .312 Inches .003 .005 .007 .010 .015 .022 .045 .070 .093 .115 mm 0.08 0.13 0.18 0.25 0.38 0.56 1.14 1.78 2.36 2.92 Inches mm .120 3.05 .140 3.56 .187 4.75 .200 5.08 .250 6.35 .312 7.92 .395 10.03 .408 10.36 .410 10.41 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Circuit diagrams are for information only. 4. All filters shall be supplied with mounting hardware (hex nut and lockwasher). Mounting hardware shall be furnished with the same finish as the filter case. 5. Terminal identification (nonsymmetrical filters): The case shall be marked at the threaded end of the filter with the symbol "L" or the circuit diagram shall be marked on the case. 6. Optional slot may be supplied, .050 ±.010 inches (1.27 ±0.25 mm) x .070 ±.010 inches (1.78 ±0.25 mm). 7. Imperfect thread or undercut optional .050 inch (1.27 mm) maximum. 8. One imperfect thread allowed .035 inch (0.89 mm) maximum. 9. Recommended mounting torque: 44 inch-ounce ±4 inch-ounce. FIGURE 1. Case and hardware dimensions and circuit diagrams - Continued. 2 MIL-PRF-28861/1D w/AMENDMENT 1 REQUIREMENTS: Design and construction: Dimensions and configuration: See figure 1. Weight: 5 grams maximum. Case finish: T, S, or G in accordance with MIL-PRF-28861 (pure tin finish is prohibited). Mounting hardware: Shall be furnished with the same finish as the filter case (pure tin finish is prohibited). Terminals: Solderable. Operating temperature range: -55°C to +125°C. Rated voltage: See table I. Rated current: 15 amperes. Capacitance: See table I. Dissipation factor: 3 percent maximum. Voltage and temperature limits of capacitance: +15 percent, -40 percent. Insulation resistance: At +25°C: 1,000 megohms minimum or 1,000 megohm-microfarads minimum, whichever is less. At +125°C: 100 megohms minimum or 100 megohm-microfarads minimum, whichever is less. Insertion loss: See table I. Voltage drop: 0.12 V dc maximum. DC resistance: 0.008 ohm maximum. -7 3 Seal: In accordance with MIL-PRF-28861. Leakage rate for class S filters shall not exceed 1 x 10 atm cm /s. Temperature rise: +25°C maximum. Solderability of terminals: In accordance with MIL-PRF-28861. Product assurance level: In accordance with MIL-PRF-28861 and table I. 3 TABLE I. Electrical characteristics. Product Dash assurance number level Style Cir- Rated Minimum cuit voltage capacitance Class B Minimum insertion loss (dB) in accordance with MIL-STD-220 2/ 3/ S DC AC 1/ volts volts (µF) At +25°C At -55°C and +125°C 30 150 300 1 10 100 1 30 150 300 1 10 100 1 kHz kHz kHz MHz MHz MHz GHz kHz kHz kHz MHz MHz MHz GHz 001, 011 X --- FS10 L2 50 --- 1.2 15 28 33 40 40 70 70 13 26 31 38 38 70 70 002, 012 X --- FS10 C 50 --- 1.2 15 28 33 40 40 70 70 13 26 31 38 38 70 70 003, 013 X X FS11 L2 70 --- 0.7 10 24 30 40 40 64 70 8 22 28 38 38 64 70 004, 014 X X FS11 C 70 --- 0.7 10 24 30 40 40 64 70 8 22 28 38 38 64 70 005, 015 X X FS11 L2 100 --- 0.45 6 19 25 36 40 60 70 4 17 23 34 38 60 70 X X FS11 C 100 --- 0.45 6 19 25 36 40 60 70 4 17 23 34 38 60 70 007, 017 X X FS11 L2 150 --- 0.25 --- 14 20 31 40 56 70 --- 12 18 29 38 56 70 008, 018 X X FS11 C 150 --- 0.25 --- 14 20 31 40 56 70 --- 12 18 29 38 56 70 009, 019 X X FS11 L2 200 125 0.15 --- 10 16 26 40 52 70 --- 9 14 25 38 52 70 4 010, 020 X X FS11 C 200 125 0.15 --- 10 16 26 40 52 70 --- 9 14 25 38 52 70 021, 031 X X FS11 L2 200 125 0.01 --- --- --- 2 20 40 55 --- --- --- --- 18 40 55 022, 032 X X FS11 C 200 125 0.01 --- --- --- 2 20 40 55 --- --- --- --- 18 40 55 023, 033 X X FS11 L2 200 125 0.0027 --- --- --- --- 10 28 45 --- --- --- --- 8 28 45 024, 034 X X FS11 C 200 125 0.0027 --- --- --- --- 10 28 45 --- --- --- --- 8 28 45 025, 035 X X FS11 L2 200 125 0.001 --- --- --- --- 2 20 35 --- --- --- --- 2 20 35 026, 036 X X FS11 C 200 125 0.001 --- --- --- --- 2 20 35 --- --- --- --- 2 20 35 1/ 0 to 400 Hz. 2/ Insertion loss measurements shall be made under full load over the frequency range of 150 kHz to 10 MHz. Insertion loss measurements above or below this frequency range shall be made under no load. 3/ The insertion loss requirements between any two adjacent specified frequencies shall be that of the lower of the two frequencies in order to accommodate resonant dips. MIL-PRF-28861/1D w/AMENDMENT 1 006, 016 MIL-PRF-28861/1D w/AMENDMENT 1 Part or Identifying Number (PIN): The PIN shall be as follows: M28861/01 - XXX | | Dash no. in accordance with figure 1 and table I X | | Case finish X | |_______ Product assurance level in accordance with MIL-PRF-28861 and table I Marking: Filters and capacitors shall be marked, as a minimum, with the following information: a. Military PIN. b. JAN brand. c. Source code. d. Date code. e. Terminal identification or circuit diagram (nonsymmetrical filters only). In addition, full marking, in accordance with MIL-PRF-28861 shall be marked on the package. Cataloging information. Dash numbers 002, 004, 006, 008, 010, 012, 014, 016, 018, 020, 022, 024, 026, 032, 034, and 036 shall be cataloged under FSC 5910 as feed-through ceramic capacitors. Dash numbers 001, 003, 005, 007, 009, 011, 013, 015, 017, 019, 021, 023, 025, 031, 033, and 035 shall be cataloged under FSC 5915 as radio frequency interference filters. * Referenced documents. In addition to MIL-PRF-28861, this specification sheet references the following documents: MIL-STD-220 Changes from previous issue. The margin of this specification sheet is marked with asterisks to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodians: Army - CR Navy - EC Air Force - 11 NASA - NA DLA - CC Preparing activity: DLA - CC (Project 59GP-0199) Review activities: Army - AV, MI Navy - AS, MC, OS, SH Air Force - 19, 99 * NOTE: The activities listed above were interested in the document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil. 5