84084

REVISIONS
LTR
A
B
C
D
E
F
G
H
J
K
DESCRIPTION
DATE
Para 3.4.6, changed insulation resistance
requirements. TABLE I, changed insertion loss
requirements for -010, -011, and -013.
Para 6.4, changed vendor style numbers
Para 3.7, changed manufacturer eligibility requirement.
Dimensional changes. TABLE I, changed insertion
loss limits on several dash numbers. Changed dc
resistance and voltage drops on -017 through -019.
Added another suggested source of supply.
Editorial changes throughout.
Figure 1, changed tolerance on terminal slot major
dimension. Added cataloging information.
Added another suggested source of supply.
Added a suggested source of supply.
Editorial changes throughout.
Page 2 - Changed PIN to include case finish
Para 3.1.3, added case finish options; prohibited pure
tin as a case finish.
Pages 4 and 6 - Added three new part numbers.
Page 7 - Added para to explain prohibition of pure tin;
added supersession table.
Page 8 - Removed source of supply.
Changes in accordance with NOR 59GP-R001-9B
Editorial changes throughout.
Page 2 - Added paragraph 2.1. Paragraph 3.1.3;
removed reference to MIL-T-10727. Added text to
include prohibition of pure tin on the hardware and as
an undercoat.
Changed drawing type to Source Control.
Added new pure tin prohibition paragraph; 3.1.3
Corrected the terminal flag position.
Editorial changes.
Editorial changes, add QR code and update vendor’s
list.
APPROVED
85-01-09
Ivan R. Jones
87-08-25
David E. Moore
88-12-05
David E. Moore
90-06-04
David E. Moore
91-11-14
David E. Moore
94-11-1
B. Boulter
98-03-24
28 OCT 2003
David E. Moore
Kendall A. Cottongim
19 AUG 2009
Michael A. Radecki
25 JUN 2015
Michael A. Radecki
CURRENT DESIGN ACTIVITY CAGE CODE 037Z3
DEFENSE LOGISTICS AGENCY
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
Prepared in accordance with ASME Y14.100
REV STATUS
K
K
REV
OF PAGES
PAGES
PMIC N/A
Original date of
drawing
11 July 1984
2
K
K
K
K
3
4
5
6
7
8
9
DESIGN ACTIVITY
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OH 45444-5000
PREPARED BY
Randy Larson
CHECKED BY
Randy Larson
K
K
TITLE
FILTERS AND CAPACITORS, RADIO
FREQUENCY/ELECTROMAGNETIC INTERFERENCE
SUPPRESSION, HERMETICALLY SEALED
APPROVED BY
Ivan R. Jones
SIZE
A
REV K
AMSC N/A
1
K
CODE IDENT. NO.
14933
DWG NO.
84084
PAGE
1
OF
9
59GP-2015-E01
1. SCOPE
1.1 Scope. This drawing and MIL-PRF-28861 describe the complete requirements for radio frequency/electromagnetic interference
suppression, hermetically sealed filters and capacitors.
1.2 Part or Identifying Number (PIN). The complete PIN is as follows:
84084I
I
Drawing
number
***
I
I
Dash number
(see figure 1
and table I)
*
I
I
Case finish
(see 3.1.3)
(NOTE: The PIN has been revised with revision F of this drawing to include a case finish option (see 3.1.3). For supersession data,
see 6.6).
2. APPLICABLE DOCUMENTS
2.1 General. The documents listed in this section are specified in sections 3 and 4 of this drawing. This section does not include
documents cited in other sections of this drawing or recommended for additional information or as examples. While every effort has
been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of
documents cited in sections 3 and 4 of this drawing, whether or not they are listed.
2.2 Government documents.
2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this drawing
to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-28861
-
Filters and Capacitors, Radio Frequency/Electromagnetic Interference Suppression, General
Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-220
MIL-STD-1285
-
Method of Insertion Loss Measurement.
Marking of Electrical and Electronic Parts.
(Copies of these documents are available online at http://quicksearch.dla.mil/.)
2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this drawing
and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes
applicable laws and regulations unless a specific exemption has been obtained.
3. REQUIREMENTS
3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-28861 and herein.
3.1.1 Terminals. Terminals shall be solderable.
3.1.2 Case dimensions. The case dimensions shall be in accordance with figure 1.
3.1.3 Pure tin prohibition. The use of pure tin is prohibited internally and externally as specified in MIL-PRF-28861.
3.1.4 Case and hardware finish. T (tin plated or tin-lead plated), S (silver plated), or G (gold plated), in accordance with MIL-PRF28861. Pure tin finish is prohibited as a final finish and as an undercoat. When used, tin plating shall have a minimum lead content of 3
percent (see MIL-PRF-28861).
DEFENSE ELECTRONICS SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
84084
REV K
PAGE
2
Inches
.005
.007
.010
.015
.020
.022
.035
.062
.093
.120
.125
mm
0.13
0.17
0.25
0.38
0.51
0.56
0.89
1.57
2.36
3.05
3.18
Inches
.250
.290
.312
.3125
.375
.430
.620
.690
.700
1.060
1.205
1.400
mm
6.35
7.36
7.92
7.937
9.53
10.92
15.75
17.52
17.78
26.92
30.61
35.56
FIGURE 1. Case dimensions and circuit configurations.
DEFENSE ELECTRONICS SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
84084
REV K
PAGE
3
PIN
84084001*
002*
003*
004*
005*
006*
007*
008*
009*
010*
011*
A
max
.700
1.060
1.060
1.060
1.060
1.060
1.060
1.060
1.060
1.060
1.060
PIN
84084012*
013*
014*
015*
016*
017*
018*
019*
020*
021*
022*
A
max
1.205
1.205
1.205
1.205
1.205
1.400
1.400
1.400
.700
.700
.700
NOTES:
1. Dimensions are in inches.
2. Metric equivalents are given for general information only.
3. Circuit diagram is for information only.
4. All filters shall be supplied with mounting hardware (hex nut and lockwasher). Mounting hardware shall be furnished
with the same finish as the filter case.
5. Terminal identification (nonsymmetrical filters): The case shall be marked at the threaded end of the filter, with the
symbol “C” or the symbol “L”, as follows, or the circuit diagram shall be marked on the case.
Circuit
L1
L2
Symbol
C
L
6. Recommended mounting torque: 60 oz-in ±4 oz-in.
7. Imperfect thread or undercut optional .062 inch (1.57 mm) maximum.
8. One imperfect thread allowed .035 inch (0.89 mm) maximum.
FIGURE 1. Case and hardware dimensions and circuit diagrams - Continued.
DEFENSE ELECTRONICS SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
84084
REV K
PAGE
4
3.1.5 Weight. The weight shall be as follows:
a. 19 grams, maximum for dash number 001, 020, 021, and 022.
b. 21 grams, maximum for dash numbers 002 through 011.
c. 30 grams, maximum for dash numbers 012 through 019.
3.2 Operating temperature range. The operating temperature range shall be -55°C to +125°C.
3.3 Temperature rise. The temperature rise shall be +25°C maximum.
3.4 Electrical characteristics.
3.4.1 Rated voltage. The rated voltage shall be 400 volts dc and 230 volts ac rms.
3.4.2 Rated current. The rated current shall be in accordance with table I.
3.4.3 Rated frequency. The rated frequency shall be dc to 400 Hz.
3.4.4 Capacitance. See table I.
3.4.5 Voltage and temperature limits of capacitance. +15, -40 percent.
3.4.6 Insulation resistance.
a. At +25°C: 1,000 megohms minimum.
b. At +125°C: 100 megohms minimum.
3.4.7 Insertion loss.
a. At +25°C: In accordance with table I.
b. At -55°C and +125°C: A 2 dB degradation from the +25°C value shall be allowed except at 1 GHz.
3.4.8 Voltage drop. Voltage drop shall be in accordance with table I.
3.4.9 DC resistance. DC resistance shall be in accordance with table I.
3.4.10 Seal. In accordance with MIL-PRF-28861, class B.
3.4.11 Solderability of terminals. In accordance with MIL-PRF-28861.
3.5 Product assurance level. Class B only.
3.6 Marking. Marking shall be in accordance with MIL-STD-1285 except the PIN shall be as specified in 1.2 with the manufacturer’s
name or code, date code, voltage rating, current rating, and terminal identification.
3.7 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MILPRF-28861 qualified products list for at least one part or perform first article inspection in accordance with the MIL-PRF-28861
qualification inspection requirements for class B.
3.8 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved
source of supply (see 6.3).
3.9 Recycled, recovered, environmentally preferable, or biobased materials. Recycled, recovered, environmentally preferable, or
biobased materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and
maintenance requirements, and promotes economically advantageous life cycle costs.
3.10 Workmanship. Parts shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance.
DEFENSE ELECTRONICS SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
84084
REV K
PAGE
5
TABLE I. Electrical characteristics.
PIN
84084-
Circuit
Voltage drop
maximum
Volts
Volts
ac rms
dc
Maximum
rated
current
(amps)
Capacitance
(µF) -0,
+100%
DC
resistance
(ohms)
maximum
100
kHz
Minimum insertion loss (dB) in
accordance with MIL-STD-220 1/ 2/
150
300
1
10
100
kHz
kHz
MHz
MHz
MHz
1
GHz
001*
C
.14
.12
15
.15
.008
7
10
16
26
40
52
70
002*
L1
.47
.165
0.5
.15
.330
18
24
32
50
60
70
70
003*
L2
.47
.165
0.5
.15
.330
18
24
32
50
60
70
70
004*
L1
.47
.15
1.0
.15
.150
12
19
30
46
60
70
70
005*
L2
.47
.15
1.0
.15
.150
12
19
30
46
60
70
70
006*
L1
.32
.078
3.0
.15
.026
7
11
19
36
60
70
70
007*
L2
.32
.078
3.0
.15
.026
7
11
19
36
60
70
70
008*
L1
.21
.065
5.0
.15
.013
7
10
16
28
54
70
70
009*
L2
.21
.065
5.0
.15
.013
7
10
16
28
54
70
70
010*
L1
.12
.08
10.0
.15
.008
7
10
16
25
48
70
70
011*
L2
.12
.08
10.0
.15
.008
7
10
16
25
48
70
70
012*
Pi
.47
.165
0.5
.20
.330
24
34
52
80
80
80
80
013*
Pi
.47
.15
1.0
.20
.150
16
27
46
74
80
80
80
014*
Pi
.32
.078
3.0
.20
.026
---
---
30
60
80
80
80
015*
Pi
.21
.065
5.0
.20
.013
---
---
12
50
80
80
80
016*
Pi
.12
.08
10.0
.20
.008
---
---
---
30
80
80
80
017*
T
.22
.07
1.0
.15
.07
6
12
25
48
70
70
70
018*
T
.32
.10
2.0
.15
.05
6
10
18
40
64
70
70
019*
T
.22
.12
4.0
.15
.03
6
10
16
31
58
70
70
020*
C
.14
.12
15
.01
.008
---
---
---
2
20
40
60
021*
C
.14
.12
15
.0027
.008
---
---
---
---
10
28
50
022*
C
.14
.12
15
.001
.008
---
---
---
---
2
20
35
1/ Insertion loss measurements shall be made under full load over the frequency range of 100 kHz to 10 MHz. Insertion loss
measurements above this frequency range shall be made under no load.
2/ The insertion loss requirements between any two adjacent specified frequencies shall be that of the lower of the two frequencies
in order to accommodate resonant dips.
DEFENSE ELECTRONICS SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
84084
REV K
PAGE
6
4. VERIFICATION
4.1 Qualification inspection. Qualification inspection is not required.
4.2 Conformance inspection.
4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of groups A and B inspections of MIL-PRF28861.
4.2.2 Certification. The acquiring activity, at its discretion, may accept a certificate of compliance with group B requirements in lieu
of performing group B tests (see 6.3c).
5. PACKAGING
5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.3). When
packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible
packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Point’s
packaging activity within the Military Department or Defense Agency, or within the military service’s system commands. Packaging
data retrieval is available from the managing Military Departments or Defense Agency’s automated packaging files, CD-ROM products,
or by contacting the responsible packaging activity.
6. NOTES
(This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.)
6.1 Intended use. Filters conforming to this drawing are intended for use when military specifications do not exist and qualified
military devices that will perform the required function are not available for OEM application. This drawing is intended exclusively to
prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military specification
exists and the product covered by this drawing has been qualified for listing on QPL-28861, this drawing becomes obsolete and will not
be used for new design. The QPL-28861 product shall be the preferred item for all applications.
6.2 Tin whisker growth. Pure tin plating is prohibited since it may result in tin whisker growth. The use of alloys with tin content
greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a
day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal
coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass,
have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM B545 (Standard Specification
for Electrodeposited Coating of Tin).
6.3 Ordering data. The contract or purchase order should specify the following:
a. Complete PIN (see 1.2).
b. Requirements for delivery of one copy of the conformance inspection data with each shipment of parts by the
manufacturer.
c. Whether the manufacturer performs the group B tests or provides certification of compliance with group B
requirements.
d. Requirements for notification of change of product to acquiring activity, if applicable.
e. Requirements for packaging and packing.
6.4 Replaceability. Filters covered by this drawing will replace the same commercial device covered by a contractor-prepared
specification or drawing.
6.5 Cataloging information. Dash number 001* and 020* through 022* shall be cataloged under FSC 5910 as a feed-through
ceramic capacitor. Dash numbers 002* through 019* shall be cataloged under FSC 5915 as radio frequency interference filters.
DEFENSE ELECTRONICS SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
84084
REV K
PAGE
7
6.6 Supersession data. Table II provides a list of supersession data from previous revisions to the superseding PIN of revision F
and later. The superseding PIN indicates only the “T” case finish since that was the only case finish available prior to revision F.
TABLE II. Supersession data.
Superseded PIN
84084001
002
003
004
005
006
007
008
009
010
011
012
013
014
015
016
017
018
019
Superseding PIN
84084001T
002T
003T
004T
005T
006T
007T
008T
009T
010T
011T
012T
013T
014T
015T
016T
017T
018T
019T
6.7 Users of record. Coordination of this document for future revisions is coordinated only with the approved source(s) of supply and
the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at
[email protected] or if in writing to: DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by
telephone (614) 692-0551 or DSN 850-0551.
6.8 Approved sources of supply. Approved source(s) of supply are listed herein. Additional sources will be added as they become
available. Assistance in the use of this drawing may be obtained online at [email protected], or by contacting DLA Land and
Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0551 or DSN 850-0551.
DLA Land and
Maritime drawing
PIN 1/
84084001*
002*
003*
004*
005*
006*
007*
008*
009*
010*
011*
012*
013*
014*
015*
016*
017*
018*
019*
020*
021*
022*
Vendor
CAGE
number
Similar
vendor
type
Vendor
CAGE
number
Similar
vendor
type
59942
59942
59942
59942
59942
59942
59942
59942
59942
59942
59942
59942
59942
59942
59942
59942
59942
59942
59942
59942
59942
59942
JD1EB-154M*
JD2EB-R07M*
JD2EB-S07M*
JD2EB-R08M*
JD2EB-S08M*
JD2EB-R10M*
JD2EB-S10M*
JD2EB-R11M*
JD2EB-S11M*
JD2EB-R12M*
JD2EB-S12M*
JD3EB-P07M*
JD3EB-P08M*
JD3EB-P10M*
JD3EB-P11M*
JD3EB-P12M*
JD4EB-T08M*
JD4EB-T09M*
JD4EB-T16M*
JD1EB-103M*
JD1EB-272M*
JD1EB-102M*
13619
13619
13619
13619
13619
13619
13619
13619
13619
13619
13619
13619
13619
13619
13619
13619
13619
13619
13619
13619
13619
13619
RF12719-1
RF12719-2
RF12719-3
RF12719-4
RF12719-5
RF12719-6
RF12719-7
RF12719-8
RF12719-9
RF12719-10
RF12719-11
RF12719-12
RF12719-13
RF12719-14
RF12719-15
RF12719-16
RF12719-17
RF12719-18
RF12719-19
RF12719-20
RF12719-21
RF12719-22
1/ Parts must be purchased to this DLA Land and Maritime PIN to assure all performance requirements and tests are met.
DEFENSE ELECTRONICS SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
84084
REV K
PAGE
8
Vendor CAGE
number
Vendor name and address
59942
AVX Filters Corporation
11144 Penrose Street
Sun Valley, CA 91352
13619
EMS Development Corp. (Formally RFI Corp.)
95 Horseblock Rd., Unit 2,
Yaphank, NY, 11980
DEFENSE ELECTRONICS SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
84084
REV K
PAGE
9