F91-AJ6 Series Low ESR, Resin-Molded Chip - Automotive Product Range FEATURES • Compliant to the RoHS2 directive 2011/65/EU • Compliant to AEC-Q200 LEAD-FREE COMPATIBLE COMPONENT APPLICATIONS • Cabin electronics • Infotainment CASE DIMENSIONS: millimeters (inches) Code EIA Code EIA Metric A 1206 3216-18 B 1210 3528-21 L 3.20 ± 0.20 (0.126 ± 0.008) 3.50 ± 0.20 (0.126 ± 0.008) A, B CASE W1 1.60 ± 0.20 (0.063 ± 0.008) 2.80 ± 0.20 (0.110 ± 0.008) W2 1.20 ± 0.10 (0.047 ± 0.004) 2.20 ± 0.10 (0.087 ± 0.004) B CASE Capacitance Code Capacitance (µF) 22 16V C 685 Rated Voltage Code 4V 6.3V 6.3V 10V 10V 16V 16V G J J A A C C Capacitance Code pF code: 1st two digits represent significant figures, 3rd digit represents multiplier (number of zeros to follow) Rated Voltage (V) 20V 25V 35V HOW TO ORDER F91 1C 226 Rated Voltage S 0.80 ± 0.20 (0.031 ± 0.008) 0.80 ± 0.20 (0.031 ± 0.008) MARKING A CASE Type H 1.60 ± 0.20 (0.063 ± 0.008) 1.90 ± 0.20 (0.075 ± 0.008) D E V M B ⵧ AJ6 Tolerance K = ±10% M = ±20% Case Size See table above Packaging See Tape & Reel Packaging Section AEC-Q200 Compliant TECHNICAL SPECIFICATIONS Category Temperature Range: Rated Temperature: Capacitance Tolerance: Dissipation Factor: ESR 100kHz: Leakage Current: Capacitance Change By Temperature 96 -55 to +125°C +85°C ±20%, ±10% at 120Hz Refer to next page Refer to next page After 1 minute’s application of rated voltage, leakage current at 20°C is not more than 0.01CV or 0.5μA, whichever is greater. After 1 minute’s application of rated voltage, leakage current at 85°C is not more than 0.1CV or 5μA, whichever is greater. After 1 minute’s application of derated voltage, leakage current at 125°C is not more than 0.125CV or 6.3μA, whichever is greater. +15% Max. at +125°C +10% Max. at +85°C -10% Max. at -55°C 051216 F91-AJ6 Series Low ESR, Resin-Molded Chip - Automotive Product Range CAPACITANCE AND RATED VOLTAGE RANGE (LETTER DENOTES CASE SIZE) Capacitance µF Code 10 106 22 226 33 336 47 476 Rated Voltage 6.3V (0J) 10V (1A) 16V (1C) A A A A B A B B B B Available Ratings RATINGS & PART NUMBER REFERENCE AVX Part No. Rated Case Capacitance Voltage Size (μF) (V) F910J226MAAAJ6 F910J336MAAAJ6 F910J476MBAAJ6 A A B 22 33 47 F911A106MAAAJ6 F911A226MAAAJ6 F911A336MBAAJ6 F911A476MBAAJ6 A A B B 10 22 33 47 F911C106MAAAJ6 F911C226MBAAJ6 F911C336MBAAJ6 A B B 10 22 33 DCL (μA) 6.3 Volt 6.3 1.4 6.3 2.1 6.3 3.0 10 Volt 10 1.0 10 2.2 10 3.3 10 4.7 16 Volt 16 1.6 16 3.5 16 5.3 DF ESR @ 120Hz @ 100kHz (%) (mΩ) 100kHz RMS Current (mA) 20°C *1 ΔC/C (%) 8 8 6 1250 1250 500 245 245 412 * * * 6 12 8 8 1500 1250 700 500 224 245 348 412 * * * * 6 8 8 1500 950 950 224 299 299 * * * * In case of capacitance tolerance ± 10% type, “K” will be put at 9th digit of type numbering system *1: ΔC/C Marked “*” Item Damp Heat Temperature cycles Resistance soldering heat Surge Endurance All Case (%) ±10 ±10 ±10 ±10 ±10 QUALIFICATION TABLE TEST Damp Heat (Steady State) Load Humidity Temperature Cycles Resistance to Soldering Heat Surge Endurance Shear Test Terminal Strength Failure Rate 051216 F91-AJ6 series (Temperature range -55ºC to +125ºC) Condition At 40°C, 90 to 95% R.H., 500 hours (No voltage applied) Capacitance Change ........... Refer to above (*1) Dissipation Factor ................ Initial specified value or less Leakage Current .................. Initial specified value or less After 1000 hour’s application of rated voltage in series with a 33Ω resistor at 85°C, 85% R.H., capacitors meet the characteristics requirements table below. Capacitance Change ........... Refer to above (*1) Dissipation Factor ................ Initial specified value or less Leakage Current .................. 125% or less than the initial specified value At -55°C / +125°C, 30 minutes each, 1000 cycles Capacitance Change ........... Refer to above (*1) Dissipation Factor ................ Initial specified value or less Leakage Current .................. Initial specified value or less 10 seconds reflow at 260°C, 10 seconds immersion at 260°C. Capacitance Change ........... Refer to above (*1) Dissipation Factor ................ Initial specified value or less Leakage Current .................. Initial specified value or less After application of surge voltage in series with a 33Ω resistor at the rate of 30 seconds ON, 30 seconds OFF, for 1000 successive test cycles at 85ºC, capacitors shall meet the characteristic requirements in the table above. Capacitance Change ........... Refer to above (*1) Dissipation Factor ................ Initial specified value or less Leakage Current .................. Initial specified value or less After 2000 hours’ application of rated voltage in series with a 3Ω resistor at 85°C, or derated voltage in series with a 3Ω resistor at 125°C, capacitors shall meet the characteristic requirements in the table above. Capacitance Change ........... Refer to above (*1) Dissipation Factor ................ Initial specified value or less Leakage Current .................. Initial specified value or less After applying the pressure load of 17.7N for 60 seconds horizontally to the center of capacitor side body which has no electrode and has been soldered beforehand on a substrate, there shall be found neither exfoliation nor its sign at the terminal electrode. Keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at both of the opposite bottom points 45mm apart from the center of capacitor, the pressure strength is applied with a specified jig at the center of the substrate so that substrate may bend by1mm as illustrated. Then, there shall be found no remarkable abnormality on the capacitor terminals. 1% per 1000 hours at 85°C, VR with 0.1Ω/V series impedance, 60% confidence level. 97