F91 Series Low ESR, Resin-Molded Chip J-Lead FEATURES • Compliant to the RoHS2 directive 2011/65/EU • SMD J-lead • Low ESR LEAD-FREE COMPATIBLE COMPONENT APPLICATIONS • General medium power DC/DC convertors B CASE C, N CASE L CASE DIMENSIONS: millimeters (inches) W1 Code H B W2 S C S N L W1 W2 H S 3.50 ± 0.20 2.80 ± 0.20 2.20 ± 0.10 1.90 ± 0.20 0.80 ± 0.20 (0.126 ± 0.008) (0.110 ± 0.008) (0.087 ± 0.004) (0.075 ± 0.008) (0.031 ± 0.008) 6.00 ± 0.20 3.20 ± 0.20 2.20 ± 0.10 2.50 ± 0.20 1.30 ± 0.20 (0.236 ± 0.008) (0.126 ± 0.008) (0.087 ± 0.004) (0.098 ± 0.008) (0.051 ± 0.008) 7.30 ± 0.20 4.30 ± 0.20 2.40 ± 0.10 2.80 ± 0.20 1.30 ± 0.20 (0.287 ± 0.008) (0.169 ± 0.008) (0.094 ± 0.004) (0.110 ±0.008) (0.051 ± 0.008) MARKING Rated Voltage (V) N CASE Capacitance (µF) 220 10V 22 16V C CASE Capacitance (µF) 68 10V B CASE Capacitance (µF) Rated Voltage (V) Rated Voltage (V) HOW TO ORDER F91 1A 107 Type Rated Voltage Capacitance Code pF code: 1st two digits represent significant figures, 3rd digit represents multiplier (number of zeros to follow) M C ⵧ Tolerance K = ±10% M = ±20% Case Size See table above Packaging See Tape & Reel Packaging Section TECHNICAL SPECIFICATIONS Category Temperature Range: Rated Temperature: Capacitance Tolerance: Dissipation Factor: ESR 100kHz: Leakage Current: Capacitance Change By Temperature -55 to +125°C +85°C ±20%, ±10% at 120Hz Refer to next page Refer to next page After 1 minute’s application of rated voltage, leakage current at 20°C is not more than 0.01CV or 0.5μA, whichever is greater. After 1 minute’s application of rated voltage, leakage current at 85°C is not more than 0.1CV or 5μA, whichever is greater. After 1 minute’s application of derated voltage, leakage current at 125°C is not more than 0.125CV or 6.3μA, whichever is greater. +15% Max. at +125°C +10% Max. at +85°C -10% Max. at -55°C SEPTEMBER 2014 ■ 91 F91 Series Low ESR, Resin-Molded Chip J-Lead CAPACITANCE AND RATED VOLTAGE RANGE (LETTER DENOTES CASE SIZE) Capacitance µF Code 6.8 685 10 106 15 156 22 226 33 336 47 476 68 686 100 107 150 157 220 227 330 337 470 477 680 687 Rated Voltage 6.3V (0J) 10V (1A) 4V (0G) 16V (1C) 20V (1D) 25V (1E) C C B C C N N N C C C/N N N C C N N N B B/C N N N N RATINGS & PART NUMBER REFERENCE AVX Part No. Case Size Capacitance (μF) Rated Voltage (V) F910G157MCC F910G227MCC F910G337MNC F910G477MNC F910G687MNC C C N N N 150 220 330 470 680 4 4 4 4 4 F910J107MCC F910J157MCC F910J227MCC F910J227MNC F910J337MNC F910J477MNC C C C N N N 100 150 220 220 330 470 6.3 6.3 6.3 6.3 6.3 6.3 F911A476MBA F911A686MCC F911A107MCC F911A157MNC F911A227MNC F911A337MNC B C C N N N 47 68 100 150 220 330 10 10 10 10 10 10 F911C226MBA F911C336MBA F911C336MCC F911C476MNC F911C107MNC B B C N N 22 33 33 47 100 16 16 16 16 16 F911D156MCC F911D336MNC F911D476MNC C N N 15 33 47 20 20 20 F911E106MCC F911E226MNC F911E336MNC F911E476MNC C N N N 10 22 33 47 25 25 25 25 F911V685MCC F911V106MNC F911V156MNC F911V226MNC C N N N 6.8 10 15 22 35 35 35 35 DCL (μA) 4 Volt 6.0 8.8 13.2 18.8 27.2 6.3 Volt 6.3 9.5 13.9 13.9 20.8 29.6 10 Volt 4.7 6.8 10.0 15.0 22.0 33.0 16 Volt 3.5 5.3 5.3 7.6 16 20 Volt 3 6.6 9.4 25 Volt 2.5 5.5 8.3 11.8 35 Volt 2.4 3.5 5.3 7.7 DF (%) @ 120Hz ESR (mΩ) @ 100kHz 100kHz RMS Current (mA) 20ºC 12 12 10 16 18 250 250 100 100 100 663 663 1225 1225 1225 8 12 14 10 14 16 250 250 250 100 100 100 663 663 663 1225 1225 1225 8 8 10 10 12 18 500 300 250 100 100 100 412 606 663 1225 1225 1225 8 8 6 6 10 950 950 400 150 100 299 299 524 1000 1225 6 6 8 450 200 200 494 866 866 6 6 8 8 450 200 200 250 494 866 866 775 6 6 6 8 600 300 300 300 428 707 707 707 * In case of capacitance tolerance ± 10% type, “K” will be put at 9th digit of type numbering system 92 ■ SEPTEMBER 2014 N N N 35V (1V) C N N N F91 Series Low ESR, Resin-Molded Chip J-Lead QUALIFICATION TABLE TEST Damp Heat (Steady State) Temperature Cycles Resistance to Soldering Heat Surge Endurance Shear Test Terminal Strength F91 series (Temperature range -55ºC to +125ºC) Condition At 40°C, 90 to 95% R.H., 500 hours (No voltage applied) Capacitance Change ........... Within ±10% of the initial value Dissipation Factor ................ Initial specified value or less Leakage Current .................. Initial specified value or less -55°C / +125°C, 30 minutes each, 5 cycles Capacitance Change ........... Within ±5% of the initial value Dissipation Factor ................ Initial specified value or less Leakage Current .................. Initial specified value or less 10 seconds reflow at 260°C, 5 seconds immersion at 260°C. Capacitance Change ........... Within ±5% of the initial value Dissipation Factor ................ Initial specified value or less Leakage Current .................. Initial specified value or less After application of surge voltage in series with a 33Ω resistor at the rate of 30 seconds ON, 30 seconds OFF, for 1000 successive test cycles at 85ºC, capacitors shall meet the characteristic requirements in the table above. Capacitance Change ........... Within ±5% of the initial value Dissipation Factor ................ Initial specified value or less Leakage Current .................. Initial specified value or less After 2000 hours’ application of rated voltage in series with a 3Ω resistor at 85°C, or derated voltage in series with a 3Ω resistor at 125°C, capacitors shall meet the characteristic requirements in the table above. Capacitance Change ........... Within ±10% of the initial value Dissipation Factor ................ Initial specified value or less Leakage Current .................. Initial specified value or less After applying the pressure load of 5N for 10±1 seconds horizontally to the center of capacitor side body which has no electrode and has been soldered beforehand on a substrate, there shall be found neither exfoliation nor its sign at the terminal electrode. Keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at both of the opposite bottom points 45mm apart from the center of capacitor, the pressure strength is applied with a specified jig at the center of substrate so that the substrate may bend by 1mm as illustrated. Then, there shall be found no remarkable abnormality on the capacitor terminals. SEPTEMBER 2014 ■ 93