Axial Lead & Cartridge Fuses 5×20 mm > Fast-Acting Fuse > 216SP Series 216SP Series, 5×20 mm, Fast Acting Fuse RoHS Pb PS E Description 5×20mm fast acting ceramic body cartridge fuse Designed to IEC specification Features • Designed to International (IEC ) Standards for use globally • Meets the IEC 60127-2, Sheet 1 specification for Fast-Acting fuses • High breaking capacity • RoHS compliant and lead-free Applications Used as supplementary protection in appliance or utilization equipment to provide individual protection for components or internal circuits. Agency Approvals Agency Ampere Range NBK080205-E10480B PS E NBK250702-E10480F 1A – 5A 6.3A – 10A CQC10012049970 1A – 10A SU05001-11001A SU05001-11002A 1A – 2.5A 3.15A – 6.3A E10480 Electrical Characteristics for Series % of Ampere Rating 210% Ampere Rating Opening Time 1A – 4A 30 minutes, Maximum 5A – 6.3A 30 minutes, Maximum 8A – 10A 30 minutes, Maximum 1A – 4A 0.01 sec.., Min.; 2 sec. Max. 5A – 6.3A 0.01 sec.., Min.; 3 sec. Max. 8A – 10A 0.04 sec., Min.; 20 sec. Max. 1A – 10A 275% 29862 1A – 10A 40013834 1 – 6.3A J50248090 8A/10A N/A 400% 1000% 1A – 10A 1A – 4A .003 sec., Min.; 0.3 sec. Max. 5A – 6.3A .003 sec., Min.; 0.3 sec. Max. 8A – 10A .01 sec.., Min.; 1.0 sec. Max. 1A – 4A .02 seconds, Maximum 5A – 6.3A .02 seconds, Maximum 8A – 10A .03 sec.onds, Maximum Electrical Characteristic Specifications by Item Amp Code Maximum Nominal Maximum Nominal Power Amp Voltage Interrupting Resistance Voltage Drop at 2 Melting I t Dissapation at Rated Current Rating Rating Rating Cold Ohms 1.5ln (A2 sec) (mV) (Ohms) (W) 250 0.2370 1000 2.5 PS E 001 1 01.6 1.6 250 0.1112 1.00500 600 4 x x x x x x x 002 2 250 0.0764 1.87000 500 4 x x x x x x x 02.5 2.5 250 0.0584 3.67200 400 4 x x x x x x x 3.15 3.15 250 004 4 250 005 5 250 0.0183 27.46000 250 4 x x x x x x x 06.3 6.3 250 0.0137 56.43000 200 4 x x x x x x x 1500 A @ 250 VAC 0.18000 Agency Approvals x x x x x x x 0.0368 6.70000 350 4 x x x x x x x 0.0247 14.99500 300 4 x x x x x x x 008 8 250 0.0123 64.31500 200 4 x x x x x x 010 10 250 0.0079 154.34000 200 4 x x x x x x I2t test at 10x rated current © 2015 Littelfuse, Inc. Application testing is strongly recommended. Specifications are subject to change without notice. Revised: 10/21/15 Axial Lead & Cartridge Fuses 5×20 mm > Fast-Acting Fuse > 216SP Series Average Time Current Curves 1A 1.6A 2A 2.5A 3.15A 4A 5A 6.3A 8A 10A Temperature Re-rating Curve 10000 1000 Time (seconds) 100 10 1 0.1 0.01 Note: Rerating depicted in this curve is in addition to the standard derating of 25% for continuous operation. 0.001 0.01 0.1 1 10 100 Amps Soldering Parameters - Wave Soldering Recommended Process Parameters: 280 Wave Parameter 260 240 220 Preheat: 200 (Depends on Flux Activation Temperature) 180 160 140 120 100 80 60 Lead-Free Recommendation (Typical Industry Recommendation) Temperature Minimum: 100°C Temperature Maximum: Preheat Time: 150°C 60-180 seconds Solder Pot Temperature: 260°C Maximum Solder Dwell Time: 2-5 seconds 40 20 Time (Seconds) Cooling Time Preheat Time Dwell Time 240 230 220 210 200 190 180 170 160 150 140 130 120 110 90 100 80 70 60 50 40 30 0 20 Recommended Hand-Solder Parameters: 0 10 Temperature (°C) - Measured on bottom side of board 300 Solder Iron Temperature: 350°C +/- 5°C Heating Time: 5 seconds max. Note: These devices are not recommended for IR or Convection Reflow process. Different values of A and B available, please contact the Littelfuse sales representative in your region: B A For the pigtailed fuse, please follow the recommendations below for axial lead forming and mounting into PCB: C Lead forming: A C B © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 10/21/15 The distance C between cap flat surface and axial lead shall be greater than 1.0 mm. PCB mounting: According to the standard of IPC-A-610, the distance between PCB and fuse cap is recommended to be a minimum of 1.5 mm. Axial Lead & Cartridge Fuses 5×20 mm > Fast-Acting Fuse > 216SP Series Product Characteristics Materials Body: Ceramic Cap: Nickel–plated Brass Leads: Tin–plated Copper Terminal Strength Operating Temperature –55ºC to +125ºC MIL-STD-202, Method 211, Test Condition A Thermal Shock MIL-STD-202, Method 107, Test Condition B (5 cycles, –65ºC to +125ºC) Solderability MIL-STD-202 Method 208 Vibration MIL-STD-202, Method 201 Product Marking Cap 1: Brand logo, current and voltage ratings Cap 2: Agency approval marks Humidity MIL-STD-202, Method 103, Test Condition A (High RH (95%) and elevated temp (40ºC) for 240 hours) Salt Spray MIL-STD-202, Method 101, Test Condition B Dimensions Part Numbering System 0216 xxxx M X E SP P All dimensions in mm 40 ± 1.0 Series +0.1 ø5.2 -0.2 20 ± 0.5 Current Rating Code Refer to Amp Code column of Electrical Characteristics Table ø0.65±0.05* 5.1 ± 0.6 5.1 ± 0.6 Quantity Code Notes: * Ratings 8A and 10A have 0.8 ± 0.05 diameter lead. M = 1000 Packaging Code X = Filler Option Codes Blank : Cartidge Type Fuse E : Axial Leaded Fuse Single-Cap Pigtail Lead-Free Packaging Packaging Option 216SP Series Bulk Packaging Specification Quantity Packaging Code Reel Size N/A 1000 MXE N/A Additional Information Datasheet Resources Samples © 2015 Littelfuse, Inc. Application testing is strongly recommended. Specifications are subject to change without notice. Revised: 10/21/15