Axial Lead & Cartridge Fuses 5×20 mm > Time-Lag > 213 Series 213 Series, 5×20 mm, Time-Lag Fuse RoHS Pb PS E Description 5×20mm time-Lag surge withstand glass body cartridge fuse designed to IEC specification. Features • Meets the IEC 60127-2, Sheet 3 specification for time-Lag fuses • RoHS compliant and lead-free. • Designed to International (IEC ) Standards for use globally • Available in cartridge and axial lead form Applications Agency Approvals Agency PS E Agency File Number Cartridge: NBK120802-E10480 A&C Leaded: NBK120802-E10480 B&D 2003010207045592 Ampere Range 1A – 5A Used as supplementary protection in appliance or utilization equipment to provide individual protection for components or internal circuits. Additional Information 6.3A 0.200A – 6.3A Datasheet Samples Resources E10480 Electrical Characteristic for Series 029862 0.200A – 6.3A 1403414 40015638 0.200A – 6.3A KM41462 0.200A – 6.3A N/A 0.200A – 6.3A % of Ampere Rating Ampere Rating Opening Time 150% 60 minutes, Minimum 210% 2 minutes, Maximum 275% 0.6 sec., Min.; 10 sec. Max. All Ratings 400% .15 sec., Min.; 3 sec. Max. 1000% 0.02 sec., Min.; 0.3 sec. Max. Electrical Characteristic Specifications by Item Amp Code .200 .250 .315 .400 .500 .630 .800 001. 1.25 01.6 002. 02.5 3.15 004. 005. 06.3 Voltage Ampere Rating Rating (V) 0.2 0.25 0.315 0.4 0.5 0.63 0.8 1 1.25 1.6 2 2.5 3.15 4 5 6.3 250 250 250 250 250 250 250 250 250 250 250 250 250 250 250 250 Interrupting Rating 35A@250Vac 40A@250Vac 50A@250Vac 63A@250Vac Maximum Maximum Nominal Power Nominal Voltage Drop Cold at Rated Dissipation Melting Resistance 2 2 Current at 1.5ln I t (A sec) (Ohms) (mV) (W) 1.6000 0.22500 1500 1.6 1.0495 0.55500 1300 1.6 0.8475 1.14000 1100 1.6 0.5350 1.36000 1000 1.6 0.3700 2.90500 900 1.6 0.2750 4.80000 300 1.6 0.1635 9.42000 250 1.6 0.1165 19.20000 150 1.6 0.0817 27.15000 150 1.6 0.0551 44.20000 150 1.6 0.0452 92.70500 150 1.6 0.0305 138.00000 120 1.6 0.0231 202.00000 100 1.6 0.0170 226.50500 100 1.6 0.0116 314.00000 100 1.6 0.0095 600.00000 100 1.6 © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Application testing is strongly recommended. Revised: 05/29/15 Agency Approvals PS E x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x Axial Lead & Cartridge Fuses 5×20 mm > Time-Lag > 213 Series Average Time Current Curves 0.200A 0.250A 0.315A 0.400A 0.500A 0.630A 0.800A 1A 1.25A 1.6A 2A 2.5A 3.15A 4A 5A 6.3A Temperature Re-rating Curve 10000 1000 TIME IN SECONDS 100 10 1 0.1 Note: 1. Rerating depicted in this curve is in addition to the standard derating of 25% for continuous operation. 0.01 0.001 0.1 1 10 100 1000 CURRENT IN AMPERES Soldering Parameters - Wave Soldering Recommended Process Parameters: 280 Wave Parameter 260 240 220 Preheat: 200 (Depends on Flux Activation Temperature) 180 160 140 120 100 80 60 Lead-Free Recommendation (Typical Industry Recommendation) Temperature Minimum: 100° C Temperature Maximum: Preheat Time: 150° C 60-180 seconds Solder Pot Temperature: 260° C Maximum Solder Dwell Time: 2-5 seconds 40 Time (Seconds) Cooling Time Preheat Time Dwell Time 240 230 220 210 200 190 180 170 160 150 140 130 120 110 90 100 80 70 60 50 40 30 0 0 20 20 10 Temperature (°C) - Measured on bottom side of board 300 Recommended Hand-Solder Parameters: Solder Iron Temperature: 350° C +/- 5°C Heating Time: 5 seconds max. Note: These devices are not recommended for IR or Convection Reflow process. © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/29/15 Axial Lead & Cartridge Fuses 5×20 mm > Time-Lag > 213 Series Product Characteristics Material Body: Glass Cap: Nickel–plated brass Leads: Tin–plated Copper Terminal Strength MIL-STD-202, Method 211, Test Condition A Solderability MIL-STD-202, Method 208 Product Marking Cap1: Brand logo, current and voltage Cap2: Agency approval marks Series Humidity Packaging Available in Bulk (M=1000 pcs/pkg) or on Tape/Reel (MRET1=1000 pcs/reel) Salt Spray Dimensions Operating Temperature –55ºC to +125ºC Thermal Shock MIL-STD-202, Method 107, Test Condition B: (5 cycles –65°C to +125°C) Vibration MIL-STD-202, Method 201 MIL-STD-202, Method 103, Test Condition A. High RH (95%) and elevated temperature (40°C) for 240 hours. MIL-STD-202, Method 101, Test Condition B Part Numbering System 20±0.5 0213 xxxx M X E P 0213 000P 5.2+0.1 -0.2 5.1±0.6 Series 5.1±0.6 Amp Code Refer to Amp Code column of Electrical Characteristics Table 0213 000 XEP 40±1.0 5.5±0.3 21.5±1.0 Quantity Code M = 1000 Packaging Code 0.65±0.05* X = Filler All dimensions in mm Option Codes Notes: * Ratings above 6.3A have 0.8±0.05 diameter lead. Blank : Cartidge Type Fuse E : Axial Leaded Fuse Lead-free Packaging Packaging Option Packaging Specification Quantity Quantity & Packaging Code Taping Width N/A N/A N/A N/A N/A N/A 1000 1000 1000 1000 1000 100 MX MXE MRET1 MXG MXB HX N/A N/A T1=53mm (2.087”) N/A N/A N/A 213 Series Bulk Bulk Reel and Tape Bulk Bulk Bulk © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/29/15