Lead-Form Type Packaging www.vishay.com Vishay Dale Film Resistor, Special Application Lead-Forming SPECIFICATIONS • EUROFORM style lead-forming for the CMF 55, 60, and 20-sizes, and the CPF 1 and 2-sizes; PSEUDO RADIAL style lead-forming for the CMF 50-size • Refer to product datasheets for the electrical characteristics and component dimensions LEADED FILM TAPE AND REEL CUT AND FORM PACKAGING MODEL PACKAGING CODE SIZE LEAD (Pb)-BEARING LEAD (Pb)-FREE STYLE PACKAGING UNIT (pieces) 2500 50 SP ER PSEUDO RADIAL 55 RL EU EUROFORM 2500 60, 20 RL EU EUROFORM 1800 1 R74 E74 EUROFORM 2500 2 R74 E74 EUROFORM 1800 CMF CPF DIMENSIONS in inches (millimeters) P H1 P1 F ΔH ΔH W2 ΔH W2 d W1 W0 W F W H0 W1 W0 H0 P1 t D0 D0 b F P0 d P0 EUROFORM DIMENSION PSEUDO RADIAL EUROFORM t PSEUDO RADIAL CMF-55, CMF-60, CPF-1 CMF-20, CPF-2 CMF-50 0.630 ± 0.020 (16.0 ± 0.5) 0.630 ± 0.020 (16.0 ± 0.5) 0.827 + 0.039, - 0 (21.0 + 1, - 0) 1.270 max. (32.25 max.) 1.270 max. (32.25 max.) - 0.197 ± 0.031 (5.0 ± 0.8) 0.197 ± 0.031 (5.0 ± 0.8) 0.197 + 0.020, - 0.004 (5.0 + 0.5, - 0.1) Lead Diameter (d) 0.024 ± 0.005 (0.6 ± 0.12) 0.032 ± 0.002 (0.813 ± 0.051) 0.020 ± 0.002 (0.51 ± 0.05) Component Spacing (P) 0.500 ± 0.039 (12.7 ± 1.0) 0.500 ± 0.039 (12.7 ± 1.0) - Feed Hole Spacing (P0) 0.500 ± 0.012 (12.7 ± 0.3) 0.500 ± 0.012 (12.7 ± 0.3) 0.500 ± 0.012 (12.7 ± 0.3) Hole Center to Lead Center (P1) 0.152 ± 0.028 (3.85 ± 0.7) 0.152 ± 0.028 (3.85 ± 0.7) 0.152 ± 0.028 (3.85 ± 0.7) Component Misalignment (ΔH) 0.079 max. (2.0 max.) 0.079 max. (2.0 max.) 0.079 max. (2.0 max.) Carrier Tape Width (W) 0.709 + 0.039, - 0.020 (18.0 + 1.0, - 0.5) 0.709 + 0.039, - 0.020 (18.0 + 1.0, - 0.5) 0.709 + 0.039, - 0.020 (18.0 + 1.0, - 0.5) Seating Plane Height (H0) Hole Center to Top of Component (H1) Lead Spacing (F) Adhesive Tape Width (W0) 0.125 min. (3.17 min.) 0.125 min. (3.17 min.) 0.236 min. (6.00 min.) Feed Hole Location (W1) 0.354 + 0.031, - 0.020 (9.0 + 0.8, - 0.5) 0.354 + 0.031, - 0.020 (9.0 + 0.8, - 0.5) 0.354 + 0.031, - 0.020 (9.0 + 0.8, - 0.5) Adhesive Tape Position [Border] (W2) 0.118 max. (3.0 max.) 0.118 max. (3.0 max.) 0.020 + 0.020, - 0 (0.5 + 0.5, - 0) Feed Hole Diameter (D0) 0.157 ± 0.008 (4.0 ± 0.2) 0.157 ± 0.008 (4.0 ± 0.2) 0.157 ± 0.008 (4.0 ± 0.2) Tape Thickness (t) 0.016 to 0.035 (0.4 to 0.9) 0.016 to 0.035 (0.4 to 0.9) 0.016 to 0.035 (0.4 to 0.9) 0.039 max. (1.0 max.) 0.039 max. (1.0 max.) - Lead Wire Protrusion (b) Notes • Cumulative pitch tolerance (dimension P0) not to exceed 1 mm/20 pitches. • Not more than 2 consecutive components and not more than 0.5 % shall be missing from the reel. • Consult factory for availability of lead-forming on other models. Revision: 26-Jun-13 Document Number: 31099 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000