919

NTE919
Integrated Circuit
High Speed Dual Comparator
Description:
The NTE919 is a precision high speed dual comparator designed to operate over a wide range of supply voltages down to a single 5V logic supply and ground and have low input currents and high gains.
The open collector of the output stage makes it compatible with TTL as well as capable of driving
lamps and relays at currents up to 25mA. Although designed primarily for for applications requiring
operation from digital logic supplies, are fully specified for power supplies up to ±15V.
Features:
D
D
D
D
D
D
D
Two Independent Comparators
Operates from a Single 5V Supply
Typically 80ns Response Time at ±15V
Minimum Fan−Out of 2 Each Side
Maximum Input Current of 1µA Over Temperature
Inputs and Outputs can be Isolated from System Ground
High Common Mode Slew Rate
Absolute Maximum Ratings:
Output to Negative Supply Voltage, VO − VCC− . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36V
Negative Supply Voltage, VCC− . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25V
Positive Supply Voltage, VCC+ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18V
Differential Input Voltage, Vid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±5V
Input Voltage (Note 1), VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±15V
Power Dissipation, Ptot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500mW
Operating Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0° to +70°C
Storage Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65° to +150°C
Lead Temperature (Soldering 10 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +260°C
Note 1. For supply voltages less than ±15 the absolute maximum input voltage is equal to the supply
voltage.
Electrical Characteristics: (VCC = ±15V, Tamb = +25°C, unless otherwise specified)
Parameter
Symbol
Input Offset Voltage (Note 2)
V10
Input Offset Current (Note 2)
Input Bias Current (Note 2)
I10
Iib
Test Conditions
Min
Typ
Max
Unit
TA = +25°C, RS ≤ 5k
−
2.0
8.0
mV
Tmin. ≤ Tamb ≤ Tmax.
−
−
10
mV
TA = +25°C, Note 2
−
80
200
nA
Tmin. ≤ Tamb ≤ Tmax.
−
−
300
nA
TA = +25°C
−
250
1000
nA
Tmin. ≤ Tamb ≤ Tmax.
−
−
1200
nA
Voltage Gain
Avd
TA = +25°C
8
40
−
V/mV
Positive Supply Current
ICC+
VCC = ±15V
−
8
12.5
mA
VCC+ = 5V, VCC− = 0V
−
4.3
−
mA
−
3
5
mA
±12
±13
−
V
1
−
3
V
−
−
±5
V
Tamb = +25°C, IO = 25mA,
V1 ≤ −5mV, V1 ≤ −10mV
−
0.75
1.5
V
VCC+ ≥ 4.5V, VCC = 0V,
IO(sink) <3.2mA, V1 ≤ −6mV, V1 ≤ −10mV
−
0.3
0.4
V
Tamb = +25°C, VO = 35V,
V1 ≥ 5mV, V1 ≥ 10mV
−
0.2
10
µA
Tmin. ≤ Tamb ≤ Tmax., V1 ≥ 5mV
−
0.2
10
µA
TA = +25°C, VS = ±15V, Note 5
−
80
−
ns
Negative Supply Current
ICC−
Input Common Mode
V lt
Voltage
Range
R
Vicm
VCC+ = 5V, VCC− = 0V
Differential Input Voltage
Vid
Low Level Output Voltage
VOL
High Level Output Current
Response Time (Note 3)
VCC = ±15V
IOH
tre
Note 2. The offset voltages and offset currents given are the maximum values required to drive the
output within a volt of either supply with a 1mA load. Thus, these parameters define an error
band and take into account the worst case effects of voltage gain and input impedance.
Note 3. The response time specified is for a 100mV input step with 5mV overdrive.
Pin Connection Diagram
GND 2
7
Non−Invert Input 2
Output 2
6
5
8
Invert Input 2 9
V (+)
V (−)
4 Invert Input 1
10
1
Output 1
3 Non−Invert Input 1
2
GND 1
.335 (8.52) Dia Max
.175
(4.45)
Max
.500
(12.7)
Min
.018 (0.45) Dia Typ
.100 (2.54)
3
4
2
5
6
1
10
.370
(9.4)
Max
7
9
8
.200 (5.08) Dia