UNISONIC TECHNOLOGIES CO., LTD L1186 CMOS IC 600mA CMOS LDO 4 5 DESCRIPTION The UTC L1186 is a COMS positive linear regulator. One of its features is the very low quiescent current typical as low as 30μA and its dropout voltage is extremely low with 600mA output current. The internal circuit includes thermal shutdown and current fold-back to prevent device failure when the circuit is operated in the bad conditions. In application, the UTC L1186 needs a low noise, regulated supply. For stable operation, the output capacitance value should be 2.2μF or more. The UTC L1186 is an ideal for battery applications, such as instrumentations, portable electronics, wireless devices, cordless phones, PC peripherals, and battery powered widgets. 1 2 3 SOT-25 1 SOP-8 FEATURES * Accurate to Within 1.5% * Quiescent Current: 30μA * Internal Over-Temperature Shutdown * With Current Limiting * Internal Short Circuit Current Fold-Back * With Noise Reduction Bypass Capacitor * Has Power-Saving Shutdown Mode * Very Low Temperature Coefficient ORDERING INFORMATION Ordering Number L1186G-xx-AF5-R L1186G-xx-S08-A-R L1186G-xx-S08-B-R Note: xx: Output Voltage, refer to Marking Information. www.unisonic.com.tw Copyright © 2015 Unisonic Technologies Co., Ltd Package SOT-25 SOP-8 SOP-8 Packing Tape Reel Tape Reel Tape Reel 1 of 7 QW-R502-319.I L1186 CMOS IC MARKING INFORMATION PACKAGE VOLTAGE CODE MARKING SOT-25 AD: ADJ SOP-8 PIN CONFIGURATION VIN 1 5 VOUT GND 2 4 ADJ EN 3 VIN 1 8 VOUT GND 2 7 GND GND 3 6 GND EN 4 5 ADJ SOT-25 SOP-8(A) SOP-8(B) PIN DESCRIPTION SOT-25 1 2 3 4 5 - PIN NO SOP-8(A) 1 2, 3, 6, 7 4 5 8 - SOP-8(B) 8 3 5 2 1 4, 6, 7 PIN NAME VIN GND EN ADJ VOUT NC UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw DESCRIPTION Input for voltage input. Ground. Enable pin. Adjusted Voltage Output voltage pin No connection 2 of 7 QW-R502-319.I L1186 CMOS IC BLOCK DIAGRAM UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 3 of 7 QW-R502-319.I L1186 CMOS IC ABSOLUTE MAXIMUM RATING (TA = 25°C, unless otherwise specified.) PARAMETER RATINGS UNIT 8 V GND-0.3 ~ VIN+0.3 V PD A Output Current IOUT VIN - VOUT SOT-25 400 Power Dissipation PD mW SOP-8 600 Junction Temperature TJ 150 °C Operating Temperature TOPR -40~+85 °C Storage Temperature TSTG -65~+150 °C Note: Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. Input Voltage Output Voltage SYMBOL VIN VOUT THERMAL RESISTANCES CHARACTERISTICS PARAMETER SYMBOL SOT-25 Junction to Ambient θJA SOP-8 SOT-25 Junction to Case (Note) θJC SOP-8 Note: θJC on center of molding compound if IC has on tab. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw RATINGS 260 200 81 65 UNIT °C/W °C/W 4 of 7 QW-R502-319.I L1186 CMOS IC ELECTRICAL CHARACTERISTICS (TA = 25°C, unless otherwise specified.) Adjusted Voltage PARAMETER Input Voltage Reference Voltage Output Voltage Accuracy Line Regulation Load Regulation Output Current Current Limit Short Circuit Current Adjusted Current Ground Pin Current SYMBOL VIN VREF VOUT ∆VOUT VOUT ∆VOUT VOUT IOUT ILIMIT ISC IADJ IGND Dropout Voltage Over Temperature Shutdown Over Temperature Hysteresis Temperature Coefficient of Output Voltage Power Supply Rejection Output Voltage Noise EN Input Threshold EN Input Bias Current VD TEST CONDITIONS IOUT=1mA IOUT=1mA VIN=VOUT+1~VOUT+2 1.4V<VOUT≤2.0V 2.0V<VOUT<4.0V MIN TYP MAX UNIT Note1 7 V 1.196 1.215 1.234 V -1.5 1.5 % -0.15 0.15 % -0.1 0.02 0.1 % IOUT=1mA~600 mA VOUT>1.3V VOUT>1.3V VOUT<0.8V IOUT=0mA IOUT=1mA~600mA IOUT =600mA VOUT=VO(NOM)-2.0% 0.2 600 600 40 20 15 30 μVrms 1.4V<VO(NOM)≤2.0V 2.0V<VO(NOM)≤2.8V 150 30 TCVO 30 eN VEH VEL IEH IEL ISD ILC f=1kHz f=10kHz f=100kHz f=10Hz~100kHz, IOUT =10mA COUT=2.2μF , CBYP=0.1μF VIN=2.7V~7V VIN=2.7V~7V VEN=VIN, VIN=2.7V~7V VEN=0V, VIN=2.7V~7V VIN=5V, VOUT =0V, VEN<VEL VPG=7V IOUT =100mA COUT=2.2μF ceramic CBYP=0.01μF 2.0 0 % mA mA 600 mA 50 μA μA 1400 mV 800 mV °C °C ppm/° C dB dB dB 800 300 30 35 OTS OTH PSRR 1 VIN 0.4 0.1 0.5 1 1 V V μA μA μA μA Shutdown Supply Current 0.5 PG Leakage Current Notes: 1. VIN(MIN)=VOUT+VD 2. To prevent the Short Circuit Current protection feature from being prematurely activated, the input voltage must be applied before a current source load is applied. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 5 of 7 QW-R502-319.I L1186 CMOS IC TYPICAL APPLICATION CIRCUIT Adjusted Voltage EN EN OUT OUT R1 IN IN + C1 1µF GND ADJ C2 100p C3 2.2µF R2 VOUT = 1.215 ( R1/R2 +1 ) C2 is unnecessary if R1 or R2 < 20 K R1 and R2 use resistance value within 1% accuracy for correct for correct VOUT UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 6 of 7 QW-R502-319.I L1186 VIN (2V/DIV) TYPICAL CHARACTERISTICS VOUT IO (500mA/DIV) (10mV/DIV) CMOS IC UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 7 of 7 QW-R502-319.I