NSTS1438

NSTS1438 Apr. 2013
NewJRC SAW FILTER
NSTS1438
Application
380MHz - 430MHz SAW FILTER
Electrical Specification: (Table 1)
The device characteristics are measured in the circuit shown in Fig.1.
Table 1. Electrical Specifications
Item
Spec.
Typ. @ 25 °C
Input and Output Impedance
50Ω
Nominal Center Frequency (f0)
405MHz
Insertion Loss
380~430MHz
1.0dB max.
0.8dB
Amplitude ripple
380~430MHz
0.5dB max.
0.1dB
Group delay ripple
380~430MHz
5ns max.
1.7ns
Input and Output Return Loss
380~430MHz
9dB min
13dB
Out of Band Rejection
551.7MHz
20dB min.
35dB
(Relative to Through Level)
536.7~566.7MHz
8dB min.
14dB
(Operating Temperature Range: -40~+85ºC)
Maximum Rating: (Table 2)
Table 2. Maximum Ratings
Item
Maximum Input Power
Maximum DC Voltage
Operating Temperature Range
Storage Temperature
Rating
+10dBm
7.5V
-40~+85ºC
-40~+85ºC
Mechanical Specifications: (Fig.2)
Package is designed as small as 3.0x3.0x1.15 [mm3] for SMD (Surface Mount Device) type.
Notice:
This part is electrostatic discharge sensitive and may be damaged by improper handling.
http://www.njr.co.jp/products/device/index.html
http://www.njr.com/products/device/index.html
(Japanese)
(English)
NSTS1438 Apr. 2013
IN
50Ω
6
1
36nH
OUT
50Ω
33nH
2 SAW 5
4
3
6pF
6pF
L: MURATA LQW18AN33NG00
L: MURATA LQW18AN36NG00
C: TAIYO YUDEN UMK105CH060DW
Fig.1 Measuring circuit
(a)
3. 0±0. 15
( b)
3. 0 ± 0. 1 5
221
( c)
NH
(1)
( 0. 6)
( 0. 2 5)
1. 1 5 ± 0. 1 5
( 2)
4
( 0. 6)
[ 2 x]
3
2
5
Marking
(1) Lot Number
(a) Year
(b) Month
*Oct.--Nov.--Dec.--(c) Date
1-9--10-19--20-31--(2) Part Number Mark
( 1. 80)
1
( 0. 75)
( 0. 45)
[ 4x]
( 0. 5 3)
[ 4 x]
6
Fig.2 Package dimensions (in mm)
0.93
3.8
1.15
3.8
0.6
2.2
0.93
1.15
Fig.3 Desirable land area (in mm)
Pin no.
1
2
3
4
5
6
Connection
GND
IN
GND
GND
OUT
GND
X
Y
Z
0
1
2
NSTS1438 Apr. 2013
Notice
1. Use this component within operating temperature range. It might not be
satisfied with electrical specification without operating temperature range.
When it is used less than -40ºC or more than +85ºC, it might be a cause of
degradation or destruction of the component. Even if it endures during a short
time, it causes degradation of qualification.
2. When soldering iron is used, solder with the temperature at the tip of soldering
iron: 350ºC max., the time of soldering: 10 seconds max., the power of
soldering iron: 30W max..
3. Notice that the allowed time of soldering with soldering iron is accumulated
time, when soldering is repeated.
4. As rapid temperature change for cleaning after reflow soldering might be a
cause of destruction clean this component after confirming that temperature of
this component goes down to room temperature.
5. Confirm that there are not any influences for qualification to this component in
mounting on PCB when this component is cleaned.
6. As it might be a cause of degradation of destruction to apply static electricity to
this component, do not apply static electricity or excessive voltage while
assembling and measuring. And do not transport this component with bare
hand.
7. As it might be a cause of degradation or destruction to apply D.C. voltage
between each terminal, apply D.C. voltage 7.5V max. in actual circuit.
Note
1. This specification specifies the quality of this component as a single unit. Make
sure that this component is evaluated and confirmed against this specification
when it is mounted to your products.
2. The information contained herein may be changed without prior notice. It is
therefore advisable to contact New Japan Radio Company before proceeding
with the design of equipment incorporating this product.
3.
The products are designed to be used with ordinary electronic equipment (data
and communications equipment, office equipment, audio-video equipment,
measuring instruments, etc). New Japan Radio Company does not assume any
liability for the case using the products with the application required high
reliability or safety extremely (such as space equipment, sea-bottom equipment,
medical equipment etc). When intending to use any our product please contact
our sales representatives in advance.
NSTS1438 Apr. 2013
FREQUENCY CHARACTERISTICS
S21
0.0
S21
0
0.5
10
1.5
Insertion Loss [dB]
Insertion Loss [dB]
1.0
2.0
2.5
3.0
3.5
4.0
20
30
40
50
4.5
5.0
60
320 340 360 380 400 420 440 460 480
350
400
450
Frequency [MHz]
10
20
Return Loss [dB]
Insertion Loss [dB]
650
5
30
40
50
60
15
20
25
30
35
70
40
80
45
0
500
1000
1500
Frequency [MHz]
2000
S21
9
8
7
6
5
4
3
2
1
340
360
380
400
Frequency [MHz]
420
320
340
360
380
400
420
Frequency [MHz]
10
Group Delay [ns]
600
S11, S22
0
10
0
320
550
Frequency [MHz]
S21
0
500
440
460
440
460
480