1508

Document 404-1
Low Profile Mini Spring™ Inductors
• Only 2 mm tall
• High Q over a wide range of frequencies
• Low DCR and excellent current handling capability
Designer’s Kit C394 contains 10 samples each 5% part
Designer’s Kit C394-2 contains 10 samples each 2% part
Terminations RoHS compliant tin-silver over copper. Other terminations available at additional cost.
Weight 48 – 130 g
Ambient temperature –40°C to +125°C with Irms current
Maximum part temperature +140°C (ambient + temp rise).
Storage temperature Component: –40°C to +140°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Temperature Coefficient of Inductance (TCL) +5 to +70 ppm/°C
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
One per billion hours / one billion hours, calculated per Telcordia SR-332
Packaging 1000/7″ reel; 3500/13″ reel Plastic tape: 2 mm wide,
0.23 mm thick, 8 mm pocket spacing, 2.2 mm pocket depth
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
Inductance2Percent Q2
SRF min4
DCR max5
Irms6
Part Wt
tol3 min (GHz)(mOhm)
number1
Turns(nH)
(A)(mg)
1508-5N5_L_3 5.5
1508-9N0_L_4 9.0
1508-13N_L_ 513.0
2508-16N_L_ 716.0
2508-18N_L_ 818.0
2508-23N_L_ 923.0
2508-27N_L_10 27.0
5,2115 5.0
5,2120 4.0
5,2100 3.0
5,2 110 3.0
5,2 110 2.9
5,2 110 2.6
5,2 110 2.3
1.Specify tolerance, termination and packaging codes:
2508-27NJLC
Tolerance:G
=2% J = 5%
Termination:L=RoHS compliant tin-silver (96.5/3.5) over copper.
Special order: T = RoHS tin-silver-copper
(95.5/4/0.5) or S = non-RoHS tin-lead (63/37).
Packaging:C
=7″ machine-ready reel. EIA-481 embossed plastic
tape (1000 parts per full reel).
B
=Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge),
use code letter C instead.
D
=13″ machine-ready reel. EIA-481 embossed plastic
tape. Factory order only, not stocked (3500 parts per
full reel).
2.6
3.4
3.9
5.2
6.0
6.8
7.9
4.0 52
4.0 65
4.0 78
4.0110
4.0118
4.0133
4.0147
2. L and Q measured at 250 MHz, 0.1 Vrms, 0 A using an Agilent/HP
4291A impedance analyzer with an Agilent/HP 16193A test fixture.
3. Tolerances in bold are stocked for immediate shipment.
4. SRF measured using an Agilent/HP 8753 network analyzer and a Coilcraft SMD-D test fixture.
5. DCR measured using a micro-ohmmeter.
6. Current that causes a 15°C temperature rise from 25°C ambient. This
information is for reference only and does not represent absolute
maximum ratings.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Document 404-1 Revised 10/13/15
Document 404-2
Low Profile Mini Spring™ Inductors
Typical L vs Frequency
Typical Q vs Frequency
50
300
45
275
27.0 nH
23.0 nH
30
25
18.0 nH
20
16.0 nH
15
13.0 nH
10
200
175
150
125
100
75
50
5
0
18.0 nH
23.0 nH
27.0 nH
225
35
Q factor
Inductance (nH)
40
13.0 nH
16.0 nH
250
1
10
100
Frequency (MHz)
1000
10000
25
0
1
10
100
1000
10000
Frequency (MHz)
Dimensions are in
inches
mm
Document 404-2 Revised 10/13/15