Document 379-1 PoE Transformer For Maxim MAX5941B PoE Interface/PWM Controller • Designed for forward topology • Operates at 275 kHz, at a 50% duty cycle Core material Ferrite Terminations RoHS tin-silver over tin over nickel over phos bronze. Other terminations available at additional cost. Weight 5.6 g Ambient temperature –40°C to +85°C Storage temperature Component: –40°C to +85°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 200 per 13″ reel Plastic tape: 44 mm wide, 0.35 mm thick, 28 mm pocket spacing, 9.6 mm pocket depth PCB washing Tested with pure water or alcohol only. For other solvents, see Doc787_PCB_Washing.pdf. Leakage Input inductance4 Part Inductance2 DCR max3 voltage Turns ratio5 number1 min (µH) (Ohms) max (µH) range (V) Isolation6 B0863-BL_ 165 0.061 (pri) 0.75 28 – 60 pri : sec1 : 0.29 1500 Vrms 1.10 (reset) pri : reset1 : 1 1.29 (bias) pri : drive1 : 0.24 0.020 (drive) pri : bias1 : 1.3 0.008 (sec) 1. When ordering, please specify a packaging code: B0863-BLD Packaging:D =13″ machine ready reel. EIA-481 embossed plastic tape (200 per full reel). B =Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter D instead. 2. Inductance is for the primary, measured at 10 kHz, 0.1 Vrms, 0 Adc. 3. DCR for the secondary is measured with the windings connected in parallel. 4. Leakage inductance is for the primary and is measured with all other windings shorted. 5. Turns ratio is with the secondary windings connected in parallel. 6. Isolation is measured from the primary, reset and bias windings to the secondary and drive windings. 7. Output is with the secondary windings connected in parallel. 8. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. 1 Primary 3 Output7 3.3 V, 4 A 12 11 Secondary 2 10 9 Reset 8 4 Drive 5 7 Bias 6 Secondary windings to be connected in parallel on PC board. US +1-847-639-6400 [email protected] UK +44-1236-730595 [email protected] Taiwan +886-2-2264 3646 [email protected] China +86-21-6218 8074 [email protected] Singapore + 65-6484 8412 [email protected] Document 379-1 Revised 05/18/12 © Coilcraft Inc. 2013 This product may not be used in medical or high risk applications without prior Coilcraft approval. Specification subject to change without notice. Please check web site for latest information. Document 379-2 PoE Transformer for Maxim MAX5941B Dot indicates pin 1 0.028 12 0,72 1 6 B0863-BL XXXXY 0.677 max 17,20 Parts manufactured prior to December 2011 may be marked differently. 7 0.098 2,5 0.865 max 21,97 0.340 max 8,64 0.004 /0,10 0.590 14,98 0.693 17,60 0.079 2,01 0.590 14,98 6 7 0.028 0,72 0.135 3,43 0.665 16,88 0.07 1,79 1 Recommended Land Pattern 1 Dimensions are in 12 0.098 2,5 0.098 2,5 inches mm US +1-847-639-6400 [email protected] UK +44-1236-730595 [email protected] Taiwan +886-2-2264 3646 [email protected] China +86-21-6218 8074 [email protected] Singapore + 65-6484 8412 [email protected] Document 379-2 Revised 12/20/11 © Coilcraft Inc. 2013 This product may not be used in medical or high risk applications without prior Coilcraft approval. Specification subject to change without notice. Please check web site for latest information.