CU8965-AL

Document 1165-1
Current Sense Transformer CU8965-AL
• Developed for Analog Devices ADP1051 Eighth Brick Power
Module
• Sensed current up to 20 A
• Frequency range: 16 kHz – 1 MHz
• Very low primary DC resistance
• 1500 Vdc, one second isolation between windings.
Core material Ferrite
Terminations RoHS compliant tin-silver over tin over nickel over phos
bronze
Weight 0.16 g
Ambient temperature –40°C to +125°C
Storage temperature Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 600/7″ reel; 2500/13″ reel Plastic tape: 16 mm wide,
0.35 mm thick, 8 mm pocket spacing, 3.0 mm pocket depth
PCB washing Tested with pure water or alcohol only. For other solvents,
see Doc787_PCB_Washing.pdf
DCR max
(Ohms)
Turns (N) Inductance2
Part number1
pri : sec
min (mH)
pri sec
CU8965-AL_1 : 100
1.33
0.0015 10.68
1. When ordering, please specify packaging code:
CU8965-ALC
Packaging:C
=7″ machine-ready reel. EIA-481 embossed plastic
tape (600 parts per full reel).
B=Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter C instead.
D=13″ machine-ready reel. EIA-481 embossed plastic
tape. Factory order only, not stocked (2500 parts per
full reel).
2. Inductance measured between secondary pins at 100 kHz, 0.1 Vrms,
0 Adc.
3. Maximum volt-time product is for the secondary, based on 2000 Gauss.
4. Primary current of 20 A causes less than 25°C temperature rise from
25°C ambient. Higher current causes a greater temperature rise (see
Temperature Rise vs Current curve).
5. Terminating resistance (RT) value is based on 1 Volt output with 20 Amps
flowing through the primary. Varying terminating resistance increases or
decreases output Voltage/Ampere according to the following equation:
RT = Vout × Nsec / Iin.
6 Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Frequency Volt-time SensedTerminating
current I 4 resistance R 5
range
product3
in
T
(kHz)
(Vµsec)
max (A)
(Ohms)
16 – 1000
32
20
5.0
Typical Circuit
4
I in
Pri
(1 turn)
2
Sec
(100 turns)
3
Specifications subject to change without notice.
Please check our website for latest information.
RT
Vout
1
Document 1165-1 Revised 07/01/15
Document 1165-2
CU8965-AL Current Sense Transformer
Temperature Rise vs Current
45
Temperature rise (from 25°C)
40
35
30
25
20
15
10
5
0
0
5
10
15
20
25
30
Current (A rms)
Dimensions
0.118
max
3,0
0.118
3,0
0.006 /0,15
0.276
max
7,0
0.197
5,0 max
0.010
0,25
0.043
1,1
0.047
1,2
1
2
3
0.102
2,60
0.043
1,1
4
1
0.043
1,1
0.047
1,2
0.043
1,1
0.073
1,85
CL
0.073
1,85
2
0.191
4,85
Dimensions are in
Recommended
Land Pattern
0.030
0,75
0.067
1,70
0.063
1,6 0.063
1,6
4
0.063
0.063 1,6
1,6
3
0.045
1,15
0.045
1,15
0.191
4,85
inches
mm
Document 1165-2 Revised 07/01/15