DO1606T

Document 213-1
SMT Power Inductors - DO1606T
• Only 2.0 mm high
• Handles current up to 2.3 Amps rms
DCRSRF
Isat3 Irms4
Part L ±20%2max ref
1
number (µH) (Ohms)(MHz) (A) (A)
DO1606T-102ML_
1.0 0.04 2302.5 2.3
DO1606T-152ML_
1.5 0.06 1802.2 2.1
DO1606T-222ML_
2.2 0.07 1401.8 1.7
DO1606T-332ML_
3.3 0.12 1101.4 1.3
DO1606T-472ML_
4.7 0.15 1001.2 1.1
DO1606T-682ML_
6.8 0.20 801.1 1.0
DO1606T-822ML_
8.2 0.23 701.0 0.95
DO1606T-103ML_
10
0.30 601.0 0.90
DO1606T-153ML_
15
0.40 450.8 0.70
DO1606T-223ML_
22
0.54 350.6 0.50
DO1606T-333ML_
33
0.74 300.5 0.45
DO1606T-473ML_
47
1.1
22 0.450.40
DO1606T-683ML_
68
1.6
20 0.350.35
DO1606T-104ML_
100
2.3
15 0.300.30
DO1606T-154ML_
150
3.5
10 0.250.25
DO1606T-224ML_
220
5.7
9 0.200.18
DO1606T-334ML_
330
8.2
8 0.160.16
DO1606T-474ML_
470 10.8
7 0.140.12
DO1606T-684ML_
680 17.2
5 0.120.10
DO1606T-105ML_ 1000 22.6
4 0.080.08
Designer’s Kit C338 contains 3 each of all values
Core material Ferrite
Core and winding loss See www.coilcraft.com/coreloss
Terminations RoHS compliant silver-palladium-platinum-glass frit.
Other terminations available at additional cost.
Weight 116 – 136 mg
Ambient temperature –40°C to +85°C with Irms current, +85°C to
+125°C with derated current
Storage temperature Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 750/7″ reel; 2500/13″ reel Plastic tape: 12 mm wide,
0.3 mm thick, 8 mm pocket spacing, 2.5 mm pocket depth
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
1. When ordering, please specify termination and packaging codes:
DO1606T-105MLC
Termination:L=RoHS compliant silver-palladium-platinum-glass frit
Special order: T = RoHS tin-silver-copper (95.5/4/0.5)
or S = non-RoHS tin-lead (63/37).
Packaging:C
=7″ machine-ready reel. EIA-481 embossed plastic
tape (750 parts per full reel).
B=Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter C instead.
D
=13″ machine-ready reel. EIA-481 embossed plastic
tape (2500 parts per full reel).
2. Inductance tested at 100 kHz, 0.1 Vrms, 0 Vdc.
3. DC current at which the inductance drops 10% (typ) from its value
without current.
4. Current that causes a 40°C temperature rise from 25°C ambient.
5. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Document 213-1 Revised 02/23/15
Document 213-2
SMT Power Inductors – DO1606T Series
Typical L vs Frequency
Typical L vs Current
10000
10000
1000 µH
100 µH
100
10 µH
10
1 µH
1
0.1
0.01
0.1
1000 µH
1000
Inductance (µH)
Inductance (µH)
1000
100 µH
100
10 µH
10
1 µH
1
1
10
0.1
0.01
1
0.1
10
Current (A)
Frequency (MHz)
XXXY
Irms Derating
0.206 max
5,23
Internal code
Dash number
Note: Parts manufactured prior to
March, 2011 were marked
only with the dash number
0.079 max
2,00
0.256 max
6,50
0.029
0,74
0.230
5,84
0.080
2,03
0.090
2,29
0.040
1,02
Recommended
Land Pattern
Dimensions are in
inches
mm
Document 213-2 Revised 02/23/15