LPO6610

Document 333-1
SMT Power Inductors – LPO6610
• Very low profile - only 1.0 mm high!
• Handles current up to 1.7 Amps rms
2
L
DCRSRF
±20%max typ Isat3 Irms4
1
Part number (µH)(Ohms) (MHz) (A) (A)
LPO6610-122ML_ 1.20.08 190 2.1 1.7
LPO6610-152ML_ 1.50.10 140 1.9 1.5
LPO6610-222ML_ 2.20.12 115 1.6 1.4
LPO6610-332ML_ 3.30.16 90 1.3 1.2
LPO6610-472ML_ 4.70.20 88 1.1 1.1
LPO6610-682ML_ 6.80.32 66 0.90 0.85
LPO6610-103ML_10 0.41 55 0.80 0.75
LPO6610-153ML_15 0.55 42 0.65 0.60
LPO6610-223ML_22 0.85 38 0.50 0.52
LPO6610-333ML_33 1.3
29 0.40 0.42
LPO6610-473ML_47 1.8
22 0.35 0.36
LPO6610-683ML_68 2.5
18 0.30 0.30
LPO6610-104ML_100
3.5
14 0.25 0.26
LPO6610-154ML_150
5.0
12 0.18 0.21
LPO6610-224ML_220
7.0
10 0.16 0.18
LPO6610-334ML_330 15.0
8 0.13 0.13
Designer’s Kit C367 contains 3 each of all values
Core material Ferrite
Core and winding loss See www.coilcraft.com/coreloss
Terminations RoHS compliant silver-palladium-platinum-glass frit.
Other terminations available at additional cost.
Weight 91.0 – 95.0 mg
Ambient temperature –40°C to +85°C with Irms current, +85°C to
+125°C with derated current
Storage temperature Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 1000/7″ reel Plastic tape: 12 mm wide, 0.3 mm thick,
8 mm pocket spacing, 1.2 mm pocket depth
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
1. When ordering, please specify termination and packaging codes:
LPO6610-334MLC
Termination:L=RoHS compliant silver-palladium-platinum-glass frit.
Special order: T = RoHS tin-silver-copper (95.5/4/0.5)
or S = non-RoHS tin-lead (63/37).
Packaging:C
=7″ machine-ready reel. EIA-481 embossed plastic
tape (1000 parts per full reel).
B=Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge),
use code letter C instead.
2. Inductance tested at 100 kHz, 0.1 Vrms, 0 Adc using an Agilent/HP
4263B LCR meter or equivalent.
3. DC current at which the inductance drops 10% (typ) from its value
without current.
4. Current that causes a 40°C temperature rise from 25°C ambient.
5. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Specifications subject to change without notice.
Please check our website for latest information.
Document 333-1 Revised 02/23/15
Document 333-2
SMT Power Inductors - LPO6610 Series
Typical L vs Frequency
Typical L vs Current
1000
1000
100 µH
10 µH
10
100 µH
100
Inductance (µH)
Inductance (µH)
100
10 µH
10
1.2 µH
1.2 µH
1
1
0.1
0.1
0.01
0.1
1
Frequency (MHz)
10
0.01
0.1
Current (A)
Irms Derating
1
10
0.270
6,90
0.100
2,50
XXXX
Dash number
0.185
4,70
Internal code
Recommended
Land Pattern
0.040 ±0.004 (See note)
1,00 ±0,10
0.192
4,90
0.216
max
5,50
0.029
0,750
0.100
2,54
0.260
max
6,60
(See note)
Dimensions are in
0.150
3,80
0.134
3,40
Note: Dimensions are before
optional solder application. For
dimensions including solder,
add 0.005 in / 0,127 mm.
inches
mm
Document 333-2 Revised 02/23/15