DO2010

Document 413-1
SMT Power Inductors – DO2010
• Smallest power inductor, only 2 mm square and 1 mm high
• Can handle up to 0.51 A of saturating current
Designer’s Kit C399 contains 5 of each part
Core material Ferrite
Core and winding loss See www.coilcraft.com/coreloss
Terminations RoHS compliant matte tin over nickel over silverplatinum-glass frit. Other terminations available at additional cost.
Weight 11 mg
Ambient temperature –40°C to +85°C with Irms current, +85°C to
+125°C with derated current
Storage temperature Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 1000/7″ reel; 3500/13″ reel Plastic tape: 12 mm wide,
0.23 mm thick, 4 mm pocket spacing, 1.19 mm pocket depth
PCB washing Tested with pure water or alcohol only. For other solvents,
see Doc787_PCB_Washing.pdf.
InductanceDCR SRF
max3
typ4 Isat5 Irms6
±20%2
Part number1 (µH) (Ohms)(MHz) (A) (A)
DO2010-123ML_ 12
1.84 35 0.510.39
DO2010-153ML_ 15
2.14 30 0.470.36
DO2010-223ML_ 22
2.80 25 0.420.32
DO2010-333ML_ 33
4.10 20 0.340.25
DO2010-473ML_ 47
6.00 16 0.280.21
DO2010-683ML_ 68
8.80 13 0.230.16
DO2010-104ML_ 100 15.7 11 0.180.13
DO2010-224ML_ 220 38.0
8.00.100.08
0.079 ±0.008
2,0 ±0,2
0.079 ±0.008
2,0 ±0,2
0.039 ±0.004
1,0 ±0,1
1. When ordering, please specify termination and packaging codes:
DO2010-123MLC
Termination:L=RoHS compliant matte tin over nickel over silverplatinum-glass frit
Special order: T = RoHS tin-silver-copper (95.5/4/0.5)
or S = non-RoHS tin-lead (63/37).
Packaging:C
=7″ machine-ready reel. EIA-481 embossed plastic
tape (1000 parts per full reel).
B=Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter C instead.
D
=13″ machine-ready reel. EIA-481 embossed plastic
tape. Factory order only, not stocked (3500 parts per
full reel).
2. Inductance tested at 100 kHz, 0.1 Vrms.
3. DCR measured on a micro-ohmmeter.
4. SRF measured using Agilent/HP 4191A or equivalent.
5. DC current at which the inductance drops 10% (typ) from its value without current.
6. Current that causes a 40°C temperature rise from 25°C ambient.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Recommended
Land Pattern
0.035
0,89
0.087
2,20
0.026
0,65
Dimensions are in
0.063
1,60
inches
mm
US +1-847-639-6400 [email protected]
UK +44-1236-730595 [email protected]
Taiwan +886-2-2264 3646 [email protected]
China +86-21-6218 8074 [email protected]
Singapore + 65-6484 8412 [email protected]
Document 413-1 Revised 12/27/10
© Coilcraft Inc. 2013
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.
Document 413-2
SMT Power Inductors – DO2010 Series
Typical L vs Current
Typical L vs Frequency
1000
1000
100
100 µH
100
100 µH
47 µH
47 µH
22 µH
22 µH
12 µH
10
12 µH
10
1
1
0.01
0.1
Current (A)
1
10
0.01
0.1
1
Frequency (MHz)
10
Typical Current Derating
100
90
80
70
60
50
40
30
20
10
0
25°C
Percent of rated current
120
110
Isat
Irms
-40
-20
0
20
40
60
80
100
120 140
Ambient temperature (°C)
US +1-847-639-6400 [email protected]
UK +44-1236-730595 [email protected]
Taiwan +886-2-2264 3646 [email protected]
China +86-21-6218 8074 [email protected]
Singapore + 65-6484 8412 [email protected]
Document 413-2 Revised 12/27/10
© Coilcraft Inc. 2013
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.