MSS6132

Document 641-1
Shielded Power Inductors – MSS6132
• 6.1 × 6.1 mm footprint; 3.2 mm high shielded inductors
• Low DCR and excellent current handling
Designer’s Kit C364 contains 3 of each value
Core material Ferrite
Core and winding loss See www.coilcraft.com/coreloss
Terminations RoHS compliant matte tin over nickel over phos
bronze (current production) or gold over nickel over phos bronze (prior
production). Other terminations available at additional cost.
Weight 0.33 – 0.38 g
Ambient temperature –40°C to +85°C with (40°C rise) Irms current.
Maximum part temperature +125°C (ambient + temp rise). Derating.
Storage temperature Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 500/7″ reel, 1500/13″ reel; Plastic tape: 16 mm wide,
0.3 mm thick, 12 mm pocket spacing, 3.1 mm pocket depth
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
4
5
Isat (A) Irms (A)
DCR SRF
2
3
Inductance max typ 10%20% 30% 20°C40°C
Part number1 ±20% (µH) (Ohms) (MHz) drop drop drop rise rise
MSS6132-472ML_ 4.7 0.043 65.0 2.18 2.602.84 2.30 3.10
MSS6132-562ML_ 5.6 0.048 60.0 2.10 2.502.74 2.20 2.95
MSS6132-682ML_ 6.8 0.052 47.0 1.80 2.122.30 2.10 2.80
MSS6132-822ML_ 8.2 0.055 45.0 1.78 2.062.22 2.00 2.65
MSS6132-103ML_ 10
0.070 39.0 1.36 1.641.84 1.90 2.50
MSS6132-123ML_ 12
0.079 33.0 1.30 1.541.70 1.75 2.35
MSS6132-153ML_ 15
0.106 27.0 1.16 1.421.56 1.65 2.20
MSS6132-183ML_ 18
0.118 24.0 1.04 1.221.36 1.55 2.05
MSS6132-223ML_ 22
0.158 21.0 0.97 1.121.22 1.45 1.90
MSS6132-273ML_ 27
0.180 19.0 0.91 1.081.18 1.30 1.75
MSS6132-333ML_ 33
0.250 18.0 0.81 0.961.10 1.20 1.60
MSS6132-393ML_ 39
0.275 17.0 0.79 0.920.99 1.10 1.45
MSS6132-473ML_ 47
0.300 16.0 0.72 0.860.93 0.95 1.30
MSS6132-563ML_ 56
0.380 14.0 0.61 0.720.79 0.85 1.15
MSS6132-683ML_ 68
0.410 12.0 0.55 0.630.69 0.73 1.00
MSS6132-823ML_ 82
0.510 10.0 0.53 0.620.67 0.60 0.85
MSS6132-104ML_100
0.660 9.0 0.45 0.540.59 0.50 0.69
1. Please specify termination and packaging codes:
MSS6132-823MLC
Termination:L=RoHS compliant matte tin over
nickel over phos bronze (current
production) or gold over nickel over
phos bronze (prior production)
Special order:
T = RoHS tin-silver-copper
(95.5/4/0.5) over gold over nickel
over phos bronze or
S = non-RoHS tin-lead (63/37) over
gold over nickel over phos bronze.
Packaging:C
=7″ machine-ready reel EIA-481
embossed plastic tape (500 per
full reel).
B
=Less than full reel In tape, but
not machine-ready. To have a leader and trailer added ($25 charge),
use code letter C instead.
D
=13″ machine-ready reel EIA-481
embossed plastic tape. Factory
order only, not stocked (1500 per
reel per full reel).
2. Inductance tested at 100 kHz, 0.1 Vrms, 0 Adc using
an Agilent/HP 4263B LCR meter or equivalent.
3. SRF measured using Agilent/HP 4191A or equilvalent.
4. DC current at which the inductance drops the specified
amount from its value without current.
5. DC current at 25°C that causes the specified inductance
drop from its value without current.
Click for temperature derating information.
6. Current that causes the specified temperature rise
from 25°C ambient. This information is for reference
only and does not represent absolute maximum ratings.
Click for temperature derating information.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components”
before soldering.
Document 641-1 Revised 09/02/15
Document 641-2
SMT Power Inductors – MSS6132
Typical L vs Current
Typical L vs Frequency
1000
100 µH
100
Inductance (µH)
Inductance (µH)
1000
22 µH
10
4.7 µH
1
0.01
1
0.1
10
Current (A)
0.240*
6,1
123
100 µH
100
22 µH
10
1
4.7 µH
0.01
0.1
1
10
Frequency (MHz)
0.237
6,0 min
0.079
2,0
0.240*
6,1
0.237
6,0
0.191
∅
4,85
Dash
number
Recommended
Land Pattern
0.112 ±0.014
2,85 ±0,35
0.079
2,0
0.220
5,6
0.220
5,6
Dimensions are in
* Dimensions are of the case not
including the termination. For
maximum overall dimensions
including the termination, add
0.016 in / 0,4 mm.
inches
mm
Document 641-2 Revised 09/02/15