PL160

Document 1072-1
SMT Planar Transformers
For Applications
up to 160 Watts
• Rated for 160 Watts
• Designed to operate between 200 kHz and 700 kHz with a
nominal 48 V input.
• High efficiency; excellent DCR; very low leakage inductance;
1500 Vrms, one minute primary to secondary isolation.
• Provides 0.009″ (0.229 mm) clearance above the seating plane
• May be special ordered with an auxiliary winding
Core material Ferrite
Terminations Matte tin over nickel over brass
Weight 12.0 – 12.8 g
Ambient temperature –40°C to +125°C
Storage temperature Component: –40°C to +125°C.
Tray packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 36 per tray
PCB washing Tested with pure water or alcohol only. For other
solvents, see Doc787_PCB_Washing.pdf
PrimaryPrimary Leakage
DCR max (mOhms)
inductance2 inductance3
Partturns
number1
N1 N2
min (µH)
max (µH)
Primary (N1) Primary (N2)Secondary4
PL160-100L
4
4
153
0.35
14.7
14.7
6.8
PL160-101L
4
5
194
0.40
14.7
18.5
6.8
PL160-102L
5
5
240
0.45
18.5
18.5
6.8
PL160-103L
5
6
290
0.55
18.5
21.5
6.8
PL160-104L
6
6
345
0.55
21.5
21.5
6.8
Volt-time Height
typ5
max
(Vµsec)
(in / mm)
150
0.352 / 8.94
168
0.352 / 8.94
187
0.360 / 9.14
206
0.375 / 9.53
224
0.375 / 9.53
product
1. To order a transformer with an optional auxiliary winding, add an “X” and the turn count after the PL160, e.g. PL160X3-100LB.
Turn counts of 2, 3, 4, 5, 7 and 9 are available for the auxiliary winding. Transformers with auxiliary windings are not stocked.
2. Inductance measured on an Agilent/HP 4284 at 200 kHz, 0.5 Vrms, 0 Adc between pins 2 and 5 with pins 3 and 4 connected.
3. Leakage inductance measured at 200 kHz, 0.5 Vrms, 0 Adc between pins 2 and 5, with pins 3 and 4 connected, and with all
secondary pins shorted.
4. DCR for secondary is measured between pins 7 and 11.
5. Volt-time product is based on primary windings connected in series.
6. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
2
Pri N1
4
3
10
1T
Pri N2
5
1
Aux (Opt)
6
[email protected]
subject to change without notice.
US +1-847-639-6400
Please check [email protected]
our website for latest information.
UK +44-1236-730595
Taiwan +886-2-2264 3646 [email protected]
China +86-21-6218 8074 [email protected]
Singapore + 65-6484 8412 [email protected]
11
1T
9
1T
8
1T
7
Document 1072-1 Revised 05/04/15
© Coilcraft Inc. 2016
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.
Document 1072-2
PL160 Series SMT Planar Transformers
Dot indicates pin 1
3
4
5
11
PL160-10xL
0.820
max
20,83
XXXXY
2
Internal code
Dash
number
-100L
-101L
-102L
-103L
-104L
10
9
8
7
Height max
(inches / mm)
0.352 / 8.94
0.352 / 8.94
0.360 / 9.14
0.375 / 9.53
0.375 / 9.53
0.920
max
23,37
0.009
min
0,229
Height
(see table)
0.004 /0,102
0.050
1,27
1
2
0.200
5,080
11
0.125
3,175
10
3
9
0.090
2,285
∅
0.080
2,03
CL
4
8
5
7
6
0.390
9,91
0.080
2,03
0.800
20,32
∅
0.110
2,79
Dimensions are in
inches
mm
Recommended
Land Pattern
US +1-847-639-6400 [email protected]
UK +44-1236-730595 [email protected]
Taiwan +886-2-2264 3646 [email protected]
China +86-21-6218 8074 [email protected]
Singapore + 65-6484 8412 [email protected]
Document 1072-2 Revised 05/04/15
© Coilcraft Inc. 2016
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.