Document 1070-1 Wideband RF Transformers – SWB • Surface mount and through hole versions • 500 V, one minute interwinding isolation (hipot) • 250 mA max current rating; 1/4 Watt RF input power • For a smaller package size, see our PWB Series Core material Ferrite Terminations RoHS compliant matte tin over nickel over phos bronze. Other terminations available at additional cost. Weight 0.37 – 0.39 g Ambient temperature –40°C to +85°C Maximum part temperature +85°C (ambient + temp rise) Storage temperature Component: –40°C to +85°C. Packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 60 per billion hours / 16,666,667 hours, calculated per Telcordia SR-332 Packaging (SM version): 500 per 13″ reel; Plastic tape: 24 mm wide, 0.45 mm thick, 20 mm pocket spacing, 6.6 mm pocket depth; (TH version): 70 per tube PCB washing Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. See Doc787_PCB_Washing.pdf. Pins 1–3 Pins 6–4 Impedance Part number Sec Pri ratio2 IDC max Frequency L min3 DCR max L min3 DCR max 6 1 Schematic Through-hole Surface mount1pri : sec (mA) (MHz) (µH)(Ohms)(µH)(Ohms) Sec Pri 1Pri 1 3 3 3Pri 1 Pri 1Pri 1 3 3 3Pri 1 Pri 1 2Pri 1 2 3 2 3 3 Sec6 6 SWB1010-PCLSWB1010-SML_1 : 1 2500.005 – 100780 0.320 780 0.320 4 SWB1010-1-PCLSWB1010-1-SML_1 : 12500.04 – 175 950.200 950.200 4 Sec4 6 Sec Sec6 5 6 5 4 5 4 Sec4 6 Sec Sec6 5 6 5 4 5 4 4 SWB1015-PCLSWB1015-SML_1.5 : 1250 0.1 – 150 800.145 510.130 SWB1040-PCLSWB1040-SML_4 : 1250 0.2 – 300 950.160 250.115 SWB2010-PCLSWB2010-SML_1 : 1 2500.005 – 100780 0.320 780 0.320 SWB2010-1-PCLSWB2010-1-SML_1 : 12500.04 – 175 950.200 950.200 SWB2040-PCLSWB2040-SML_4 : 1 250 0.2 – 300 95 0.160 25 0.115 SWB3010-PCLSWB3010-SML_1 : 1 2500.005 – 100780 0.320 780 0.320 SWB3010-1-PCLSWB3010-1-SML_1 : 12500.04 – 175 950.200 950.200 SWB3015-PCLSWB3015-SML_1.5 : 1250 0.1 – 150 800.145 510.130 SWB3040-PCLSWB3040-SML_ 4 : 1250 0.2 – 300 950.160 250.115 1. When ordering, please specify a packaging code: SWB3040-SMLD Packaging:D =13″ machine ready reel. EIA-481 embossed plastic tape (500 parts per full reel). B =Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter D instead. 2. Impedance ratio is for the full primary winding to the full secondary winding. 3. Inductance tested at 130 kHz, 0.1 Vrms, 0 Adc. 4. Electrical specifications at 25°C. Measurements are referenced to 50 Ohms. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. US +1-847-639-6400 [email protected] UK +44-1236-730595 [email protected] Taiwan +886-2-2264 3646 [email protected] China +86-21-6218 8074 [email protected] Singapore + 65-6484 8412 [email protected] Document 1070-1 Revised 04/25/16 © Coilcraft Inc. 2016 This product may not be used in medical or high risk applications without prior Coilcraft approval. Specification subject to change without notice. Please check web site for latest information. Document 1070-2 Wideband RF Transformers – SWB Typical Attenuation vs Current 0.310 max 7,87 Dot over Pin #1 M Hz 0.100 2,54 typ 0.300 ±0.010 7,62 ± 0,25 0 .3 0 0.310 max 7,87 0.270 max 6,86 0 MH Dot over Pin #1 6 5 3 4 0.025 dia typ 0,64 0.012 × 0.020 typ 0,30 × 0,50 z 2.5 5 10 20 50 100 IDC (mA) 2 3 0.400 typ 10,16 0.03 0,76 For SSWB10XX, pins 2 and 5 are removed during manufacture. For SWB20XX, pin 2 is removed during manufacture. Dimensions are in Typical Frequency Response SWB1010, SWB2010, SWB3010 3 dB bandwidth 0.005 – 100 MHz 0.520 13,2 6 0.10 2,5 0.10 2,5 5 4 Recommended Land Pattern Part Marking 0.020 typ 0,50 200 1 0.402 10,2 0.520 ±0.010 13,21 ±0,25 0.100 typ 2,54 15 0.06 1,52 0.225 max 5,72 0.025 max 0,64 SWBxxxx XXXX Y Part number Internal codes inches mm SWB1010-1, SWB2010-1, SWB3010-1 3 dB bandwidth 0.04 – 175 MHz 0 dBm Attenuation 0 dBm Attenuation 1 2 z MH 5 10 1 2 3 4 5 6 7 1 2 3 4 5 6 7 0.001 0.01 0.10 1.0 Frequency (MHz) 10 8 100 0.01 SWB1015, SWB3015 3 dB bandwidth 0.1 – 150 MHz 0.10 1.0 10 Frequency (MHz) 100 1000 SWB1040, SWB2040, SWB3040 3 dB bandwidth 0.2 – 300 MHz 0 dBm Attenuation 0 dBm Attenuation 0.100 2,54 0.100 2,54 0.157 4,0 1.0 dBm Attenuation 10 1 2 3 4 5 6 7 8 0.30 7,62 0.225 max 5,72 0 8 Recommended Board Layout 0.270 max 6,86 1 2 3 4 5 6 7 0.01 0.10 01.0 10 Frequency (MHz) 100 1000 8 0.01 0.10 1.0 10 Frequency (MHz) 100 1000 Attenuation measured on a network analyzer (re: 50 Ohms) US +1-847-639-6400 [email protected] UK +44-1236-730595 [email protected] Taiwan +886-2-2264 3646 [email protected] China +86-21-6218 8074 [email protected] Singapore + 65-6484 8412 [email protected] Document 1070-2 Revised 04/25/16 © Coilcraft Inc. 2016 This product may not be used in medical or high risk applications without prior Coilcraft approval. Specification subject to change without notice. Please check web site for latest information. DCN-736 Document +/-0.25mm