XPL2010

Document 646-1
Shielded Power Inductors XPL2010
• Ultra-miniature, magnetically shielded power inductors
• AEC-200 Grade 1 qualified (–40°C to +125°C ambient)
• Very low DCR, excellent current handling, soft saturation
Core material Composite
Core and winding loss See www.coilcraft.com/coreloss
Weight 20 mg
Environmental RoHS compliant, halogen free
Terminations RoHS compliant tin-silver-copper (96.5/3/0.5) over tin over
nickel over silver-platinum. Other terminations available at additional cost.
Ambient temperature –40°C to +125°C with (40°C rise) Irms current.
Maximum part temperature +165°C (ambient + temp rise). Derating.
Storage temperature Component: –40°C to +165°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 2000/7″ reel; 7500/13″ reel Plastic tape: 8 mm wide,
0.23 mm thick, 4 mm pocket spacing, 1.19 mm pocket depth
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
Isat (A)5
Irms (A)6
Inductance2
DCR (Ohms)3
SRF typ4
Part number1
±20% (µH)
nom max
(MHz)
10% drop 20% drop 30% drop
20°C rise 40°C rise
XPL2010-201ML_0.200.024
0.027
4082.80
3.45
3.752.2
2.8
XPL2010-331ML_0.330.031
0.035
3091.90
2.75
3.051.9
2.6
XPL2010-501ML_0.500.040
0.045
2181.80
2.35
2.641.7
2.3
XPL2010-681ML_0.680.057
0.063
1521.55
1.95
2.191.5
2.1
XPL2010-821ML_0.820.068
0.075
1321.25
1.65
1.901.3
1.7
XPL2010-102ML_
1.0
0.0810.089 117
1.20 1.60 1.80
1.1 1.6
XPL2010-152ML_
1.5
0.1050.116 80
0.950 1.30 1.50
1.0 1.4
XPL2010-222ML_
2.2
0.156
0.173 75
0.9401.201.35
0.961.3
XPL2010-332ML_
3.3
0.2070.228 55
0.700 0.9251.05
0.79 1.1
XPL2010-472ML_
4.7
0.3360.370 40
0.580 0.7500.845
0.74 1.0
XPL2010-682ML_
6.8
0.4210.463 33
0.450 0.6200.725
0.64 0.87
XPL2010-822ML_
8.2
0.4570.503 30
0.440 0.6000.670
0.55 0.75
XPL2010-103ML_
10
0.5550.611 28
0.390 0.5250.610
0.49 0.66
XPL2010-183ML_ 18
1.471.60 31
0.5000.560
0.590 0.320.43
XPL2010-223ML_ 22
1.892.00 25
0.4100.470
0.510 0.280.39
XPL2010-333ML_ 33
2.592.85 20
0.3300.380
0.410 0.230.31
XPL2010-473ML_ 47
3.964.25 17
0.2700.300
0.320 0.180.25
XPL2010-563ML_ 56
4.484.82 15
0.2400.280
0.300 0.170.24
XPL2010-683ML_ 68
6.146.56 13
0.2100.250
0.280 0.150.20
XPL2010-823ML_ 82
6.456.90 12
0.2000.240
0.260 0.150.20
XPL2010-104ML_ 100
8.489.27 11
0.1800.214
0.232 0.130.17
XPL2010-224ML_ 220
19.2 21.1
7.1 0.122 0.1430.161
0.0860.116
1. When ordering, please specify termination and packaging codes:
XPL2010-103MLC
Termination:L = RoHS compliant tin-silver-copper (96.5/3/0.5) over
tin over nickel over silver.
Special order: S = non-RoHS tin-lead (63/37).
Packaging:C
=7″ machine-ready reel. EIA-481 embossed plastic
tape (2000 parts per full reel).
B=Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge),
use code letter C instead.
D
=13″ machine-ready reel. EIA-481 embossed plastic
tape. Factory order only, not stocked (7500 parts per
full reel).
2. Inductance tested at 100 kHz, 0.1 Vrms, 0 Adc.
3. DCR measured on a micro-ohmmeter.
4. SRF measured using Agilent/HP 4395A or equivalent.
5. DC current at 25°C that causes an inductance drop of 30% (typ) from
its value without current. Click for temperature derating information.
6. Current that causes the specified temperature rise from 25°C ambient.
This information is for reference only and does not represent absolute
maximum ratings. Click for temperature derating information.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Document 646-1 Revised 09/01/15
Document 646-2
Shielded Power Inductors – XPL2010 Series
Typical L vs Current
Typical L vs Frequency
1000
1000
220 µH
220 µH
100 µH
33 µH
10 µH
10
3.3 µH
1.0 µH
1
100 µH
100
Inductance (µH)
Inductance (µH)
100
33 µH
10 µH
10
3.3 µH
1.0 µH
1
0.33 µH
0.33 µH
0.1
0.01
1
0.1
10
Current (A)
0.079 ±0.008
2,0 ±0,2
Dot
indicates
start
0.1
0.1
1
10
100
Frequency (MHz)
Products manufactured
prior to June 2015
may not have a dot.
0.075 ±0.008
1,9 ±0,2
0.039
max
1,00
0.065
1,65
0.018
0,45
0.014
min
0,35
0.035
typ
0,90
0.057
1,45
0.087
2,2
0.041
1,04
Recommended
Land Pattern
Dimensions are in
inches
mm
Tape and reel orientation
Document 646-2 Revised 09/01/15