H-XS-1W&G-XS-1W Series 1W,Isolated 6000VDC Unregulated Single&Dual Output DC/DC Converters SELECTION GUIDE Input Output Voltage Voltage Output Current (V) (V) (MA) G0505XS-1W 5 ±5 G0509XS-1W 5 ±9 FEATURES G0512XS-1W 5 G0515XS-1W RoHS compliant ◆ Efficiency up to 80% ◆ Power density up to 0.42W/cm3 ◆ Wide temperature performance at full 1 Watt ◆ load,-40°C to 85 °C Single and dual output ◆ UV 94V-0 package material ◆ No heatsink required ◆ 3.3V,5V,12V input ◆ Isolation MTTF1 (KHRS) (MA) Efficiency (%) Capacitive ±100 40 60 3.0 4950 ±55 30 65 3.0 3832 ±12 ±42 20 65 3.0 2770 5 ±15 ±33 20 65 3.0 1903 G1205XS-1W 12 ±5 ±100 40 60 3.0 3688 G1209XS-1W 12 ±9 ±55 30 65 3.0 3029 G1212XS-1W 12 ±12 ±42 20 65 3.0 2324 G1215XS-1W 12 ±15 ±33 20 65 3.0 1682 H0303XS-1W 3.3 3.3 303 70 66 3.0 13780 H0503XS-1W 5 3.3 303 60 64 3.0 13460 H0505XS-1W 5 5 200 50 68 3.0 13360 H0509XS-1W 5 9 111 50 72 3.0 12700 H0512XS-1W 5 12 83 50 71 3.0 11490 H0515XS-1W 5 15 66 50 71 3.0 9980 H1205XS-1W 12 5 200 50 69 3.0 8447 H1209XS-1W 12 9 111 50 73 3.0 8176 H1212XS-1W 12 12 83 50 73 3.0 7660 H1215XS-1W 12 15 66 50 74 3.0 6950 Order code Ripple&Noise2 (PF) Industry standard pinout ◆ Footprint 1.91cm2 ◆ INPUT CHARACTERISTICS 6KVDC isolation ◆ Parameter 3.3V,5V,9V,12V and 15V output ◆ Voltage range Internal SMD construction ◆ Conditions Min. Typ. Max Continuous operation,3V input types 2.97 3.3 3.63 Continuous operation,5V input types 4.5 5 5.5 Continuous operation,12V input types 10.8 12 13.2 Units V Fully encapsulated with toroidal Magnetics ◆ No external components required ◆ ABSOLUTE MAXIMUM RATINGS MTTF up to 13 million hours ◆ Short-circuit protection3 1 second Lead temperature 1.5mm from case for 10 seconds 300°C Input voltage VIN,H/G03 types 5V Input voltage VIN,H/G05 types 7V Input voltage VIN,H/G12 types 15V No electrolytic or tantalum capacitors ◆ Custom solutions available ◆ MODEL SELECTION ① ② ③ ④ ⑤ ⑥ H 05 05 X S -1W ①Product Series ③Output Voltage ⑤SIP Package 1.Calculated using MIL-HDBK-217FN2 calculation model with nominal input voltage at full load. 2.See ripple&noise test method. ②Input Voltage ④Fixed Input ⑥Rated Power 3.Supply voltage must be disconnected at the end of the short circuit duration. All specifications typical at TA=25°C,nominal input voltage and rated output current unless otherwise specified. APPLICATIONS The H_XS-1W&G_XS-1W series are dual and single output DC/DC converters in a 7 pin SIP package style offering pin and functionality compatibility with the E series SIP DC/DC converters. The H_XS-1W&G_XS-1W series is Ul60950 recognized and suitable for applications where safety and miniaturization are of paramount importance.Isolation barrier approved for supplementary/reinforced insulation. MICRODC RESERVES THE COPYRIGHT http://www.microdc.cn Technical Enquiries-Email:[email protected] Tel:0086-20-86000646 Page 1 of 4 H-XS-1W&G-XS-1W Series OUTPUT CHARACTERISTICS Parameter Rated Power1 Voltage Set Point Line regulation Conditions Min. TA=-40℃～60℃ Typ. Max. Units 1 W %% 0.1 See tolerance envelope High Vin to low Vin 1.0 1.2 10% load to rated load,xx03 10.0 15.0 Load regulation 10% load to rated load,0505 7.0 10.0 Single outputs 10% load to rated load,0509,0512,0515 6.0 10.0 10% load to rated load,12xx 5.0 7.0 10% load to rated load,5V output types 10.0 15.0 Load regulation 10% load to rated load,9V output types 6.0 10.0 Dual outputs 10% load to rated load,12V output types 6.0 10.0 10% load to rated load,15V output types 6.0 10.0 All types 250 Zero Load Power % % MW ISOLATION CHARACTERISTICS Parameter Isolation test voltage Resistance Conditions Min. Flash tested for 1 second 5200 Viso=500VDC Typ. Max. Units VDC GΩ 1 GENERAL CHARACTERISTICS Parameter Conditions Min. Typ. Single output 45 Dual output 70 Max. Switching frequency Units kHz TEMPERATURE CHARACTERISTICS Parameter Conditions Specification All output types Min. Storage Case Temperature above Typ. Max. -40 60 -55 130 All output types Units ℃ 33 TEMPERATURE DERATING GRAPH TOLERANCE ENVELOPE H-XS/G-XS-1W 3.3V in,3V out type only 1.See derating graph. All specifications typical at TA=25°C, nominal input voltage and rated output current unless otherwise specified.Another 24V& 48V products, please inquire Our technical department! http://www.microdc.cn Technical Enquiries-Email:[email protected] Tel:0086-20-86000646 Page 2 of 4 H-XS-1W&G-XS-1W Series TECHNICAL NOTES ISOLATION VOLTAGE "Hi Pot Test","Flash Tested","Withstand Voltage","Proof Voltage","Dielectric Withstand Voltage"&”Isolation Test Voltage" are all terms that relate to the same thing, a test voltage. Applied for a specified time, across a component designed to provide electrical isolation, to verify the integrity of that isolation. Professional Power Module H_XS-1W&G_XS-1W series of DC/DC converters are all 100% production tested at their stated isolation voltage. This is 6KVDC for 1 second. A question commonly asked is,"What is the continuous voltage that can be applied across the part in normal operation?" The H_XS-1W&G_XS-1W series has been recognized by Underwriters Laboratory to 300Vrms for Supplementary Insulation and 150Vrms for Reinforced Insulation. REPEATED HIGH-VOLTAGE ISOLATION TESTING It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materials. Construction and environment. We therefore strongly advise against repeated high voltage isolation testing. but if it is absolutely required, that the voltage be reduced by 20% from specified test voltage. OUTPUT RIPPLE REDUCTION By using the values of inductance and capacitance stated, the output ripple at the rated load is lowered to 5mV p-p max. Component selection Capacitor: Ceramic chip capacitors are recommended. It is required that the ESR(Equivalent Series Resistance)should be as low as possible.X7R types are recommended. The voltage rating should be at least twice(except for 15V output),the rated output voltage of the DC/DC converter. Inductor: The rated current of the inductor should not be less than of the output of the DC/DC converter. At the rated current, the DC resistance of the inductor should be such that the voltage drop across the inductor is <2% of the rated voltage of the DC/DC converter. The SRF(Self Resonant Frequency) should be >20MHz. Single output types Dual output types OUTPUT RIPPLE REDUCTION Ripple & Noise Characterization Method Ripple and noise measurements are performed with the following test configuration. C1 1uF X7R multilayer ceramic capacitor, voltage rating to be a minimum of 3 times the output voltage of the DC/DC converter C2 10uF tantalum capacitor, voltage rating to be a minimum of 1.5 times the output voltage of the DC/DC converter C3 100nF multilayer ceramic capacitor, general purpose R1 450Ω resistor, carbon film,±1% tolerance R2 50Ω BNC termination T1 3T of the caox cable through a ferrite toroid RLOAD Resistive load to the maximum power rating of the DC/DC converter. Connections should be made via twisted wires R3 50Ω resistor, carbon film,±1% Measured values are multiplied by 10 to obtain the specified values. Differential Mode Noise Test Schematic http://www.microdc.cn Technical Enquiries-Email:[email protected] Tel:0086-20-86000646 Page 3 of 4 H-XS-1W&G-XS-1W Series PACKAGE SPECIFICATIONS MECHANICAL DIMENSIONS PIN CONNECTIONS SIP7 package SINGLE OUTPUT DUAL OUTPUT PIN CONNECTIONS-7 PIN SIP PIN CONNECTIONS-7 PIN SIP pin Function pin Function 1 +VIN 1 +VIN 2 -VIN 2 -VIN 5 -VOUT 5 -VOUT 7 +VOUT 6 0V 7 +VOUT *Pin not fitted on single output variants. All dimensions in inches ±0.01(mm±0.25mm).All pins on a 0.1(2.54) pitch and within ±0.01(0.25)of true position. Weight: 4.3g RECOMMENDED FOOTPRINT DETAILS 7 Pin SIP Package *Hole not required for single output variants. Unless otherwise stated all dimensions in inches ±0.01(mm ±0.25mm). TUBE OUTLINE DIMENSIONS 7 Pin SIP Tube Unless otherwise stated all dimensions in inches ±0.02(mm ±0.5mm). Tube length(7 Pin SIP):20.669(525mm±2mm). Tube Quantity:25 RoHS COMPLIANT INFORMATION This series is compatible with RoHS soldering systems with a peak wave solder temperature of 300°C for 10 seconds. The pin termination finish on the SIP package type is Tin Plate, Hot Dipped over Matte Tin with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in this series are backward compatible with Sn/Pb soldering systems. Microdc Professional Power Module,Inc. Tel:0086-20-86000646 E-mail:[email protected] Website:http://www.microdc.cn Microdc Professional Power module,Inc.makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. Specifications are subject to change without notice. 2010 Microdc Professional Power Module, Inc. Guangzhou http://www.microdc.cn REACH COMPLIANT INFORMATION This series has proven that this product does not contain harmful chemicals, it also has harmful chemical substances through the registration, inspection and approval. Technical Enquiries-Email:[email protected] Tel:0086-20-86000646 Page 4 of 4