Huck 360 ® Advanced Fastening System Free-spinning installation Absorbs high spike loads Vibration and fatigue resistant 3/8" – 1-3/8", 10mm – 36mm Huck 360 System ® The engineered nut-and-bolt fastening system from the leader in vibration-resistant fastening, Huck. The goal was simple: to design a high-strength bolting system that resists vibration loosening, no matter how extreme the environment. This system should offer quick installation and removal with conventional tools, deliver superior fatigue strength, and hold tight under high spike loads. The result is the Huck 360®, the most advanced nutand-bolt fastening system you’ll find on the market today. Easy-to-install, the Huck 360 fastening system is engineered to be virtually maintenance free and resistant to vibration, even under extreme conditions. The Huck 360® System is available in 3/8", 1/2", 5/8", 3/4", 7/8", 1", 1-1/8", 1-3/8", 10mm, 12mm, 16mm, 20mm, and 36mm. The difference is in the design Huck 360® stays tight under severe vibration loading by eliminating the “gap” around the crest of the bolt. When tightened, the Huck 360 fills this gap, which prevents transverse motion between the 360 nut and bolt, keeping the assembly in place. Huck 360® Conventional thread TR AN SVER SE VI B R ATION BOLT N UT Thread Flanks are Locked. Nut cannot move relative to bolt. 2 BOLT N UT Thread Flanks can slide. Nut can move relative to bolt. Transverse vibration comparison CLAMP LOAD (lbf) ® This chart shows that once vibration begins, clamp load quickly decays with conventional nuts and bolts, while it holds constant with Huck 360®. Increased life Because the Huck 360® was designed with shallow, low-notch factor bolt threads (the grooves aren’t rolled as deep as a conventional bolt), the effective area of the fastener itself is widened by as much as 20%, increasing tensile and fatigue strength. In fact, the Huck 360 thread delivers 5 times the fatigue life of a standard thread bolt. Improved fatigue performance Finite Element Analysis (FEA) reveals that the shallow thread form of the Huck 360® results in 27% less axial stress in the root than conventional bolt threads. Stress concentration is the primary contributing factor leading to fatigue failures. Huck 360® Reduce maintenance, save time The Huck 360 installs faster and more easily than the nuts and bolts you’re accustomed to using, and maintenance intervals can be extended. The Huck 360’s superior fatigue strength has proven to increase equipment uptime and productivity. ® Conventional thread Huck 360 benefits ® 27% less stress in the root of the bolt thread. ■ Resists vibration loosening ■ Withstands high spike loads ■ Increases equipment uptime ■ ■ Installs 300% faster than conventional locknuts Can be installed and removed with conventional tools Huck 360 Re-Usability ® A Huck 360 nut and bolt can be retightened. It can be reused if the nut and bolt set remains free spinning after removal and reuse, with the same torque requirements as the first installation. ® 3 Inch Data and dimensions Inch HUCK 360® Grade 8 Bolt Diameter (inches) DT(*) A B H T D 6" or shorter Over 6" Min. Ult. Tensile LBF 11,600 3/8 12 0.639 0.557 0.303 0.372 1.14 1.39 7/16 14 0.710 0.619 0.361 0.435 1.3 1.55 1/2 16 0.853 0.743 0.403 0.497 1.43 1.68 5/8 20 1.067 0.930 0.504 0.622 1.71 1.96 3/4 24 1.277 1.113 0.604 0.746 1.97 2.21 50,100 7/8 28 1.491 1.299 0.706 0.871 2.24 2.49 69,300 1 32 1.704 1.485 0.790 0.995 2.51 2.76 90,900 15,900 — 21,300 33,900 Additional diameters available upon request. Head style (Hex) Material Length Code Finish 36 0 H - DT ( * ) X ( * ** )( ** ) Diameter in 1/32" increments Example: 360H-DT12X125 is a HUCK 360 fastener, Hexagonal head, 3/8" Diameter, Length 1-1/4". Lengths and Diameters 4 Nom. Length Length Code (***) DT12 "L" — Underhead Length (Inches) 1.250 DT14 DT16 DT20 DT24 DT28 DT32 1-1/4" X125 1-3/8" X137 1.375 1-1/2" X150 1.500 1.500 1-5/8" X162 1.625 1.625 1-3/4" X175 1.750 1.750 1-7/8" X187 1.875 1.875 2" X200 2.000 2.000 2-1/8" X212 2.125 2.125 2-1/4" X225 2.250 2.250 2-3/8" X237 2.375 2.375 2-1/2" X250 2.500 2.500 2-5/8" X262 2.625 2.625 2-3/4" X275 2.750 2.750 2-7/8" X287 2.875 2.875 3" X300 3.000 3.000 3-1/4" X325 3.250 3.250 3.250 3.250 3.250 3.250 3.250 3-1/2" X350 3.500 3.500 3.500 3.500 3.500 3.500 3.500 2.000 Notes 2.250 2.250 2.500 2.500 2.750 2.750 2.750 3.000 3.000 3.000 1.Finishes: Black oiled (no suffix) or Geomet (D1 suffix) 2.Raised or depressed Huck mark, six equally spaced bars, and Huck mark as shown. 3.000 3.000 3-3/4" X375 3.750 3.750 3.750 3.750 3.750 3.750 3.750 4" X400 4.000 4.000 4.000 4.000 4.000 4.000 4.000 4-1/4" X425 4.250 4.250 4.250 4.250 4.250 4.250 4.250 4-1/2" X450 4.500 4.500 4.500 4.500 4.500 4.500 4.500 4-3/4" X475 4.750 4.750 4.750 4.750 4.750 4.750 4.750 5" X500 5.000 5.000 5.000 5.000 5.000 5.000 5.000 5-1/4" X525 5.250 5.250 5.250 5.250 5.250 5.250 5.250 5-1/2" X550 5.500 5.500 5.500 5.500 5.500 5.500 5.500 5/3/4" X575 5.750 5.750 5.750 5.750 5.750 5.750 5.750 6" X600 6.000 6.000 6.000 6.000 6.000 6.000 6.000 6-1/4" X625 6.250 6.250 6.250 6.250 6.250 6.250 6.250 6-1/2" X650 6.500 6.500 6.500 6.500 6.500 6.500 6.500 6-3/4" X675 6.750 6.750 6.750 6.750 6.750 6.750 6.750 3.Material: Medium carbon alloy steel Inch Huck 360® Nut Diameter (inches) R(*) C F J M Min. Ult. Tensile LBF 3/8 12 0.779 0.679 0.45 0.349 11,600 7/16 14 0.848 0.739 0.525 0.407 15,900 1/2 16 0.99 0.863 0.6 0.465 21,300 5/8 20 1.202 1.047 0.75 0.581 33,900 3/4 24 1.413 1.231 0.9 0.697 50,100 7/8 28 1.625 1.416 1.04 0.805 69,300 1 32 1.836 1.6 1.2 0.93 90,900 Style (Straight hex) Material Finish 3 6 0 N H - R ( * )( ** ) Diameter in 1/32" increments Example: 360NH-R12 is a HUCK 360 Straight Hex Nut, 3/8" Diameter. Additional diameters available upon request. Notes 1. Hardened washers recommended (per ASTM F436 or equivalent). 2. Finishes: Zinc Electroplate with Red Dye Chromate (no suffix) or Geomet (D1 suffix) 3.Depressed Huck mark and “360 Bolt Only” as shown for 5/8" diameter and up. Depressed Huck mark only for 1/2" diameter and under. 4.Material: Low carbon steel 5.All dimensions nominal and subject to manufacturing tolerances. 5 Metric Data and dimensions Metric HUCK 360® Class 10.9 Bolt Diameter (mm) A B H D T 125 mm < — (4.92 in.) >125 mm < 200 mm mm > (200 — 7.87 in.) Min. Ult. Tensile kn DT10 18 16 8 10 26 --- --- 60.3 DT12 20 18 10 12 30 --- --- 87.7 DT14* 24 21 11 14 34 40 --- 120 DT16 27 24 13 16 38 44 --- 163 255 DT20 34 30 16 20 46 52 --- DT24* 41 36 20 24 54 60 73 367 DT36 62 54 23 36 --- 84 97 850 * Check for availability. Additional diameters available upon request. Head style (Hex) Material Length in mm increments M 360 - DT ( * ) X ( *** )( ** ) Diameter in mm increments Finish Example: M360H-DT10X045 is a Metric HUCK 360 fastener, Hexagonal head, 10mm Diameter, Length 45mm. Lengths and Diameters 6 "L" — Underhead Length (mm) Nom. Length (mm) (***) 45 X045 45 50 X050 50 55 X055 55 55 60 X060 60 60 60 65 X065 65 65 65 70 X070 70 70 70 70 80 X080 80 80 80 80 80 90 X090 90 90 90 90 90 90 100 X100 100 100 100 100 100 100 DT10 DT12 DT14 DT16 DT20 DT24 DT36 50 65 Notes 110 X110 110 110 110 110 110 120 X120 120 120 120 120 120 1. Finishes: Black oiled (no suffix) or Geomet (D1 suffix) 2.Raised or depressed Huck mark, 10.9, and the number 360 as shown 130 X130 130 130 130 130 130 140 X140 140 140 140 140 140 150 X150 150 150 150 150 160 X160 160 160 160 160 180 X180 180 180 180 200 X200 200 200 200 220 X220 220 220 240 X240 240 240 260 X260 260 280 X280 280 300 X300 300 4. Material: Medium carbon alloy steel 5.All dimensions nominal and subject to manufacturing tolerances. Metric Huck 360® Nut C F J M Min. Ult. Tensile kn 20.41 18 11.94 9.30 60.3 R12 23.52 21 14.48 11.15 87.7 R14 26.94 24 16.76 13.00 120 Diameter (mm) R10 R16 30.38 27 19.05 14.76 163 R20 38.35 34 24.13 18.59 255 R24 46.28 41 28.70 23.30 367 R36 67.87 60 43.18 33.48 850 Style (Straight hex) Material Finish M 3 6 0 N H - R ( * )( ** ) Diameter in mm increments Example: M360NH-R10 is a Metric HUCK 360 Nut, Straight hex style, 10mm Diameter. Additional diameters available upon request. Notes 1.Hardened washers recommended (per ASTM F436 or equivalent). 2.Finish: Zinc Electroplate, with Red Dye Chromate (no suffix) or Geomet (D1 suffix) 3.Depressed Huck Mark and “360 Bolt Only” as shown for 16mm diameter and up. Depressed Huck mark only for 14mm diameter and under. 4.Material: Low carbon steel 5.All dimensions nominal and subject to manufacturing tolerances. 7 Alcoa Fastening Systems ® For more than 120 years, the name Alcoa has been recognized worldwide as a strong leader in product quality and customer support. These strengths are found in every product manufactured for Alcoa Fastening Systems, offering the greatest breadth and depth of fastening system solutions in the industry. Alcoa Fastening Systems (AFS) maintains company offices in the United States and in many other countries. AFS fastener distributors are also located in many of the world’s industrial centers, where they provide a ready source of AFS fasteners, installation tools, tool parts, and application assistance. Americas International Locations Industrial Fastener Division 8001 Imperial Drive Waco, TX 76712, USA P.O. Box 8117 Waco, TX 76714-8117, USA Tel: 800 388 4825 Fax: 800 798 4825 Installation Tool Division 1 Corporate Drive Kingston, NY 12401, USA Tel: 800 278 4825 Fax: 845 334 7333 AFS Industrial Distribution Group Headquarters 1925 North MacArthur Drive Tracy, CA 95376, USA Tel: 209 839 3000 Fax: 209 839 3022 AFS Industrial Distribution 14300 Clay Terrace Blvd. Suite 250 Carmel, IN 46032, USA Tel: 800 826 2884 Fax: 800 573 2645 India Operations Unit no. 28, Chowringhee Court 55/1, Chowringhee Road Kolkata – 700071 India Tel: +91 33 4069 9170/80 Fax: +91 33 4069 9184 Latin America Sales Avenida Parque Lira 79-402 Tacubaya Mexico C P 11850 Tel: +52 55 5515 1776 Fax: +52 55 5277 7564 Japan/Korea Sales Alcoa Japan Ltd. #1013 NBF Hibiya Bldg. Uchisaiwai-cho, Chiyoda-ku Tokyo 100-1011 Japan Tel: +81 3 3539 6577 Fax: +81 3 3539 6585 Brazil Sales Av. Nações Unidas, 12.901 Torre Oeste, 3° andar São Paulo - SP - Brasil 04578-000 Tel: 0800 015 9888 Fax: +55 11 5509 0200 Melbourne Operations 1508 Centre Road Clayton, Victoria, 3168 Australia Tel: +61 3 8545 3333 Fax: +61 3 8545 3390 Suzhou Sales 58 Yinsheng Road, Shengpu Suzhou Industrial Park Suzhou Jiangsu 215126 China Tel: 0512 62823800-8888 Fax: 0512 62863810 AFShuck.net youtube.com/AFSindustrial Disclaimer: The information contained in this publication is only for general guidance, and is not intended to create any warranty, express, implied, or statutory; all warranties are contained only in AFS’s written quotations, acknowledgments, and/or purchase orders. It is recommended that the user secure specific, up-to-date data and information regarding each application and/or use of such products. © 2014 Alcoa Fastening Systems. All rights reserved. AFS5517C 0114 1M Telford Operations Unit C, Stafford Park 7 Telford, Shropshire TF3, 3BQ United Kingdom Tel: +44 1952 2900 11 Fax: +44 1952 2904 59 Alcoa Fastening Systems St Cosme Operations 9 rue de Cressonnieres 72110 Saint Cosme en Varais France Tel: +33 0 2.43.31.41.00 Fax: +33 0 2.43.31.41.41 Alcoa Fastening Systems Kelkheim Operations Industriestr. 6 65779 Kelkheim Germany Tel: +49 [0] 6195 8050 Fax: +49 [0] 6195 2001