NICHIA STS-DA1-2755C <Cat.No.131107> NICHIA CORPORATION SPECIFICATIONS FOR UV LED NSHU551B ● Built-in ESD Protection Device ● RoHS Compliant NICHIA STS-DA1-2755C <Cat.No.131107> SPECIFICATIONS (1) Absolute Maximum Ratings Symbol Absolute Maximum Rating Unit Forward Current Item IF 25 mA Pulse Forward Current IFP 80 mA Allowable Reverse Current IR 85 mA Power Dissipation PD 100 mW Operating Temperature Topr -30~85 °C Storage Temperature Tstg -40~100 °C Junction Temperature TJ 100 °C * Absolute Maximum Ratings at TA=25°C. * IFP conditions with pulse width ≤10ms and duty cycle ≤10%. (2) Initial Electrical/Optical Characteristics Item Symbol Condition Typ Unit VF IF=20mA 3.4 V Radiant Flux Φe IF=20mA 5.4 mW Peak Wavelength λp IF=20mA 365 nm Δλ IF=20mA 12 nm Forward Voltage Spectrum Half Width * Characteristics at TA=25°C. * Radiant Flux value as per CIE 127:2007 standard. 1 NICHIA STS-DA1-2755C <Cat.No.131107> RANKS Item Forward Voltage Radiant Flux Peak Wavelength Rank Min Max Unit - 2.9 4.0 V 8 6.8 9.6 7 4.8 6.8 6 3.4 4.8 Ua 360 370 mW nm * Ranking at TA=25°C. * Forward Voltage Tolerance: ±0.05V * Radiant Flux Tolerance: ±10% * Peak Wavelength Tolerance: ±3nm * LEDs from the above ranks will be shipped. The rank combination ratio per shipment will be decided by Nichia. 2 NICHIA STS-DA1-2755C <Cat.No.131107> OUTLINE DIMENSIONS * 本製品はRoHS指令に適合しております。 This product complies with RoHS Directive. 管理番号 No. NSHU551x STS-DA7-2622A (単位 Unit:±0.2) mm) (単位 Unit: mm, 公差 Tolerance: 5.4 4 4.7 ガラス窓 Glass (2.5) Anode Φ0.5 3.6±0.4 K A 保護素子 Protection Device 1 0.4 14.5±1 1 Cathode 項目 Item 内容 Description ガラス窓材質 Glass Materials 硬質ガラス Hard Glass キャップ材質 Cap Materials 鉄合金+ニッケルメッキ Ni-plated Iron Alloy リード材質 Lead Materials 鉄合金+金メッキ Au-plated Iron Alloy 質量 Weight 0.27g(TYP) 3 NICHIA STS-DA1-2755C <Cat.No.131107> SOLDERING • Recommended Hand Soldering Condition • Recommended Dip Soldering Condition Temperature 350°C Max Pre-Heat 120°C Max Soldering Time 3sec Max Pre-Heat Time 60sec Max No closer than 3mm from Solder Bath the base of the lead. Temperature Position Dipping Time Dipping Position 260°C Max 10sec Max No closer than 3mm from the base of the lead. * Solder the LED no closer than 3mm from the base of the lead. * Dip soldering/hand soldering must not be performed more than once. * Care should be taken to avoid cooling at a rapid rate and ensure the peak temperature ramps down slowly. * When soldering, do not apply stress to the lead frame while the LED is hot. * When using a pick and place machine, choose an appropriate nozzle for this product. * After soldering, the LED position must not be corrected. * After soldering, NO mechanical shock or vibration should be applied to LED cap until the LEDs cool down to room temperature. * In order to avoid damage on the cap during cutting and clinching the leads, it is not recommended to solder the LEDs directly on customer PCB without any gap between the cap and the board. If it is unavoidable, customer is advised to check whether such soldering will not cause wire breakage or cap damage. Direct soldering to double-sided PCBs must be avoided due to an increased effect of heat on the cap. * When it is necessary to clamp the LEDs to prevent soldering failure, it is important to minimize the mechanical stress on the LEDs. * Cut the LED lead frames at room temperature. Cutting the lead frames at high temperature may cause failure of the LEDs. * Consider factors such as the dip soldering temperature, hand soldering temperature, etc. when choosing the solder. * When flux is used, it should be a halogen free flux. Ensure that the manufacturing process is not designed in a manner where the flux will come in contact with the LEDs. 4 NICHIA STS-DA1-2755C <Cat.No.131107> PACKAGING - BULK 管理番号 No. Nxxxxxxx STS-DA7-1137B 袋の表示 Label printed on the bag 帯電防止袋 Anti-electrostatic Bag UV LED Type Lot Qty Nxxxxxxx ******* YMxxxx-RRR pcs RoHS NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN UV LED LED RADIATION LED放射 CAUTION TO ELECTROSTATIC DAMAGE 静電気に注意 警告ラベル Warning and Explanatory Labels LE LED 放射 D 光学測定装置で 帯電防止袋を並べて入れ、 ダンボールで仕切ります。 Anti-electrostatic bags are packed in cardboard boxes with corrugated partitions. UV LED LED LED RADIATION RADIATION DOAVOID NOT VIEW DIRECTLY TO WITH EXPOSURE OPTICAL INSTRUMENTS BEAM ビームを直接見たり触れたり 直接観察してはならない しないこと E クラス1M クラス 3B LLED製品 D 製品 CLAS 1M LED LED CLASS PRODUCT 3B T S PRODUC ラベル Label attached to the box UV LED TYPE Nxxxxxxx ******* RANK RRR QTY. PCS RoHS NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN Nichia LED * 客先型名を*******で示します。 客先型名が設定されていない場合は空白です。 ******* is the customer part number. If not provided, it will not be indicated on the label. * ロット表記方法についてはロット番号の項を 参照して下さい。 For details, see "LOT NUMBERING CODE" in this document. * 本製品は帯電防止袋に入れたのち、 輸送の衝撃から保護するためダンボールで梱包します。 Products are packed in an anti-electrostatic bag. They are shipped in cardboard boxes to protect them from external forces during transportation. * 取り扱いに際して、 落下させたり、 強い衝撃を与えたりしますと、 製品を損傷させる原因になりますので注意して下さい。 Do not drop or expose the box to external forces as it may damage the products. * ダンボールには防水加工がされておりませんので、 梱包箱が水に濡れないよう注意して下さい。 Do not expose to water. The box is not water-resistant. * 輸送、 運搬に際して弊社よりの梱包状態あるいは同等の梱包を行って下さい。 Using the original package material or equivalent in transit is recommended. 5 NICHIA STS-DA1-2755C <Cat.No.131107> LOT NUMBERING CODE Lot Number is presented by using the following alphanumeric code. YMxxxx - RRR Y - Year Year Y 2009 9 2010 A 2011 B 2012 C 2013 D 2014 E M - Month Month M Month M 1 1 7 7 2 2 8 8 3 3 9 9 4 4 10 A 5 5 11 B 6 6 12 C xxxx-Nichia's Product Number RRR-Ranking by Wavelength, Ranking by Radiant Flux 6 NICHIA STS-DA1-2755C <Cat.No.131107> DERATING CHARACTERISTICS NSHU551x 管理番号 No. STS-DA7-2695A 周囲温度-許容順電流特性 Ambient Temperature vs Allowable Forward Current Derating1 許容順電流 Allowable Forward Current(mA) 50 40 30 (25, 25.0) 20 10 (85, 5.00) 0 0 20 40 60 80 100 120 周囲温度 Ambient Temperature(°C) デューティー比-許容順電流特性 Duty Ratio vs Allowable Forward Current Duty TA =25°C 許容順電流 Allowable Forward Current(mA) 100 80 25 10 1 1 10 100 デューティー比 Duty Ratio(%) 7 NICHIA STS-DA1-2755C <Cat.No.131107> OPTICAL CHARACTERISTICS NSHU551B 管理番号 No. STS-DA7-4228A * 本特性は参考です。 All characteristics shown are for reference only and are not guaranteed. 発光スペクトル Spectrum T A=25°C IF=20mA Spectrum 1.0 相対発光強度 Relative Emission Intensity(a.u.) 0.8 0.6 0.4 0.2 0.0 300 350 400 450 500 550 600 波長 Wavelength(nm) Directivity1 指向特性 Directivity T A=25°C IFP=20mA -20° -10° 0° 10° 20° 30° -30° 40° 放射角度 Radiation Angle -40° 50° -50° -60° 60° -70° 70° 80° -80° -90° 90° 1 0.5 0 0.5 1 相対放射強度 Relative Radiant Intensity(a.u.) 8 NICHIA STS-DA1-2755C <Cat.No.131107> FORWARD CURRENT CHARACTERISTICS / TEMPERATURE CHARACTERISTICS * 本特性は参考です。 All characteristics shown are for reference only and are not guaranteed. 順電圧-順電流特性 Forward Voltage vs Forward Current 管理番号 No. 周囲温度-順電圧特性 Ambient Temperature vs Forward Voltage VfIf T A=25°C 100 NSHU551B STS-DA7-4229 IFP=5mA IFP=20mA IFP=60mA TaVf 5.0 80 順電圧 Forward Voltage(V) 順電流 Forward Current(mA) 4.5 20 10 4.0 3.5 3.0 1 2.5 2.5 3.0 3.5 4.0 4.5 5.0 -60 -40 -20 順電圧 Forward Voltage(V) 順電流-相対放射束特性 Forward Current vs Relative Radiant Flu x 0 20 40 60 80 100 120 周囲温度 Ambient Temperature(°C) 周囲温度-相対放射束特性 Ambient Temperature vs Relative Radiant Flux IfIv T A=25°C TaIv IFP= 20mA 1.4 4.0 相対放射束 Relative Radiant Flux(a.u.) 相対放射束 Relative Radiant Flux(a.u.) 3.5 3.0 2.5 2.0 1.5 1.0 1.2 1.0 0.8 0.5 0.6 0.0 0 20 40 60 順電流 Forward Current(mA) 80 100 -60 -40 -20 0 20 40 60 80 100 120 周囲温度 Ambient Temperature(°C) 9 NICHIA STS-DA1-2755C <Cat.No.131107> FORWARD CURRENT CHARACTERISTICS / TEMPERATURE CHARACTERISTICS * 本特性は参考です。 All characteristics shown are for reference only and are not guaranteed. 順電流-ピーク波長特性 Forward Current vs Peak Wavelength 管理番号 No. NSHU551B STS-DA7-4233 T A=25°C IfλD 371 ピーク波長 Peak Wavelength(nm) 369 367 365 363 361 359 1 10 100 順電流 Forward Current(mA) 周囲温度-ピーク波長特性 Ambient Temperature vs Peak Wavelength IFP= 20mA TaλD 371 ピーク波長 Peak Wavelength(nm) 369 367 365 363 361 359 -60 -40 -20 0 20 40 60 80 100 120 周囲温度 Ambient Temperature(°C) 10 NICHIA STS-DA1-2755C <Cat.No.131107> RELIABILITY (1) Tests and Results Reference Test Test Test Conditions Standard Duration Resistance to JEITA ED-4701 Tsld=260±5°C, 10sec, 1dip, Soldering Heat 300 302 3mm from the base of the lead JEITA ED-4701 Tsld=245±5°C, 5sec, 303 303A Lead-free Solder(Sn-3.0Ag-0.5Cu) JEITA ED-4701 -40°C(30min)~25°C(5min)~ 100 105 100°C(30min)~25°C(5min) Moisture Resistance JEITA ED-4701 25°C~65°C~-10°C, 90%RH, (Cyclic) 200 203 24hr per cycle Terminal Bend JEITA ED-4701 5N, 0°~90°~0°bend, Strength 400 401 2bending cycles Terminal Pull JEITA ED-4701 Strength 400 401 High Temperature JEITA ED-4701 Storage 200 201 Temperature Humidity JEITA ED-4701 Storage 100 103 Low Temperature JEITA ED-4701 Storage 200 202 Solderability Temperature Cycle Room Temperature Operating Life Temperature Humidity Operating Life Low Temperature Operating Life Failure Criteria # Units Failed/Tested #1 0/50 #2 0/50 100cycles #1 0/50 10cycles #1 0/50 #1 0/50 #1 0/50 10N, 10±1sec TA=100°C 1000hours #1 0/50 TA=60°C, RH=90% 1000hours #1 0/50 TA=-40°C 1000hours #1 0/50 TA=25℃, IF=25mA 500hours #1 0/50 60°C, RH=90%, IF=15mA 500hours #1 0/50 TA=-30°C, IF=20mA 1000hours #1 0/50 NOTES: Measurements are performed after allowing the LEDs to return to room temperature. (2) Failure Criteria Criteria # #1 #2 Items Conditions Failure Criteria Forward Voltage(VF) IF=20mA >U.S.L.×1.1 Radiant Flux(ΦE) IF=20mA <L.S.L.×0.7 - Less than 95% solder coverage Solderability U.S.L. : Upper Specification Limit L.S.L. : Lower Specification Limit 11 NICHIA STS-DA1-2755C <Cat.No.131107> CAUTIONS (1) Lead Forming ● When forming leads, the leads should be bent at a point at lease 3mm from the base of the lead. Do not use the base of the leadframe as a fulcrum during lead forming. ● Lead forming should be done before soldering. ● Do not apply any bending stress to the base of the lead. The stress to the base may damage the LED's characteristics or it may break the LEDs. ● When mounting the product onto a printed circuit board, the via-holes on the board should be exactly aligned with the lead pitch of the product. If the LEDs are mounted with stress at the leads, it causes deterioration of the cap and this will degrade the LEDs. (2) Storage ● Shelf life of the products in unopened bag is 3 months(max.) at <30°C and 70% RH from the delivery date. If the shelf life exceeds 3 months or more, the LEDs need to be stored in a sealed container with silica gel desiccants to ensure their shelf life will not exceed 1 year. ● Nichia LED leadframe are gold plated iron alloy. This gold surface may be affected by environments which contain corrosive substances. Please avoid conditions which may cause the LED to corrode, tarnish or discolor. This corrosion or discoloration may cause difficulty during soldering operation. It is recommended that the LEDs be used as soon as possible. ● To avoid condensation, the products must not be stored in the areas where temperature and humidity fluctuate greatly. ● Do not store the LEDs in a dusty environment. ● Do not expose the LEDs to direct sunlight and/or an environment where the temperature is higher than normal room temperature. (3) Directions for Use ● When designing a circuit, the current through each LED must not exceed the Absolute Maximum Rating. Operating at a constant current per LED is recommended. In case of operating at a constant voltage, Circuit B is recommended. If the LEDs are operated with constant voltage using Circuit A, the current through the LEDs may vary due to the variation in Forward Voltage characteristics of the LEDs. (A) (B) ... ... ● This product should be operated using forward current. Ensure that the product is not subjected to either forward or reverse voltage while it is not in use. In particular, subjecting it to continuous reverse voltage may cause migration, which may cause damage to the LED die. When used in displays that are not used for a long time, the main power supply should be switched off for safety. ● It is recommended to operate the LEDs at a current greater than 10% of the sorting current to stabilize the LED characteristics. ● Ensure that excessive voltages such as lightning surges are not applied to the LEDs. ● For outdoor use, necessary measures should be taken to prevent water, moisture and salt air damage. ● This LED also emits visible light. Please take notice of visible light spectrum, in case you use this LED as light source of sensors etc. (4) Handling Precautions ● Do not handle the LEDs with bare hands as it will contaminate the LED surface and may affect the optical characteristics: it might cause the LED to be deformed and/or the wire to break, which will cause the LED not to illuminate. The lead could also cause an injury. ● Dropping the product may cause damage. ● Do not stack assembled PCBs together. Failure to comply can cause the cap portion of the product to be cut, chipped, delaminated and/or deformed. It may cause wire to break, leading to catastrophic failures. 12 NICHIA STS-DA1-2755C <Cat.No.131107> (5) Design Consideration ● PCB warpage after mounting the products onto a PCB can cause the package to break. The LED should be placed in a way to minimize the stress on the LEDs due to PCB bow and twist. ● The position and orientation of the LEDs affect how much mechanical stress is exerted on the LEDs placed near the score lines. The LED should be placed in a way to minimize the stress on the LEDs due to board flexing. ● Board separation must be performed using special jigs, not using hands. (6) Electrostatic Discharge (ESD) ● The products are sensitive to static electricity or surge voltage. ESD can damage a die and its reliability. When handling the products, the following measures against electrostatic discharge are strongly recommended: Eliminating the charge Grounded wrist strap, ESD footwear, clothes, and floors Grounded workstation equipment and tools ESD table/shelf mat made of conductive materials ● Ensure that tools (e.g. soldering irons), jigs and machines that are being used are properly grounded and that proper grounding techniques are used in work areas. For devices/equipment that mount the LEDs, protection against surge voltages should also be used. ● If tools or equipment contain insulating materials such as glass or plastic, the following measures against electrostatic discharge are strongly recommended: Dissipating static charge with conductive materials Preventing charge generation with moisture Neutralizing the charge with ionizers ● The customer is advised to check if the LEDs are damaged by ESD when performing the characteristics inspection of the LEDs in the application. Damage can be detected with a forward voltage measurement at low current (≤1mA). ● ESD damaged LEDs may have current flow at a low voltage. Failure Criteria: VF<2.0V at IF=0.5mA (7) Thermal Management ● Proper thermal management is an important when designing products with LEDs. LED die temperature is affected by PCB thermal resistance and LED spacing on the board. Please design products in a way that the LED die temperature does not exceed the maximum Junction Temperature (TJ). ● Drive current should be determined for the surrounding ambient temperature (TA) to dissipate the heat from the product. (8) Cleaning ● The LEDs should not be cleaned with water, benzine, and/or thinner. ● If required, isopropyl alcohol (IPA) should be used. Other solvents may cause premature failure to the LEDs due to the damage to the resin portion. The effects of such solvents should be verified prior to use. In addition, the use of CFCs such as Freon is heavily regulated. ● When dust and/or dirt adheres to the LEDs, soak a cloth with Isopropyl alcohol (IPA), then squeeze it before wiping the LEDs. ● Ultrasonic cleaning is not recommended since it may have adverse effects on the LEDs depending on the ultrasonic power and how LED is assembled. If ultrasonic cleaning must be used, the customer is advised to make sure the LEDs will not be damaged prior to cleaning. 13 NICHIA STS-DA1-2755C <Cat.No.131107> (9) Eye Safety ● In 2006, the International Electrical Commission (IEC) published IEC 62471:2006 Photobiological safety of lamps and lamp systems, which added LEDs in its scope. On the other hand, the IEC 60825-1:2007 laser safety standard removed LEDs from its scope. However, please be advised that some countries and regions have adopted standards based on the IEC laser safety standard IEC 60825-1:20112001, which still includes LEDs in its scope. Most of Nichia's LEDs can be classified as belonging into either the Exempt Group or Risk Group 1. High-power LEDs, that emit light containing blue wavelengths, may be classified as Risk Group 2. Please proceed with caution when viewing directly any LEDs driven at high current, or viewing LEDs with optical instruments which may greatly increase the damages to your eyes. ● Viewing a flashing light may cause eye discomfort. When incorporating the LED into your product, please be careful to avoid adverse effects on the human body caused by light stimulation. ● The products are UV light LEDs, and radiate intense UV light during operation. Since UV light can be harmful to eyes, do NOT look directly into the UV light, even through an optical instrument. In case of the light reflection, UV protective glasses are required to use in order to avoid damage by the light. (10) Others ● The LEDs described in this brochure are intended to be used for ordinary electronic equipment (such as office equipment, communications equipment, measurement instruments and household appliances). Consult Nichia's sales staff in advance for information on the applications in which exceptional quality and reliability are required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or health (such as for airplanes, aerospace, submersible repeaters, nuclear reactor control system, automobiles, traffic control equipment, life support systems and safety devices). ● The customer shall not reverse engineer by disassembling or analysis of the LEDs without having prior written consent from Nichia. When defective LEDs are found, the customer shall inform Nichia directly before disassembling or analysis. ● The specifications and appearance of this product may change without notice; Nichia does not guarantee the contents of this specification. Both the customer and Nichia will agree on the official specifications of supplied products before the volume production of a program begins. 14