[INCH-POUND] A-A-55534/1A 23 December 2002 SUPERSEDING A-A-55534/1 19 February 1997 COMMERCIAL ITEM DESCRIPTION RESISTORS, FIXED, WIRE WOUND OR METAL ELEMENT, (POWER TYPE) STYLE VLV1 The General Services Administration has authorized the use of this commercial item description (CID) for all federal agencies. 1. SCOPE. This CID covers the general requirements for style VLV1 wire wound or metal element, power type, fixed resistors. The resistors covered by this CID are intended for commercial/industrial applications. 2. CLASSIFICATION. This CID uses a classification system which is included in the Part Identification Number (PIN). The PIN shall be AA55534/01- (plus a coded number) as shown in the following example. F | | Resistance tolerance (see 3.3) NOTE: This PIN has been derived in accordance with A-A-55534. AA55534/01| | CID number R010 | | Resistance value (see 3.2) B | | Termination finish (see 3.4) 3. SALIENT CHARACTERISTICS 3.1 Design and construction. The resistors supplied to this CID shall be as specified herein (see figure 1). 3.2 Resistance value. The resistance value shall be 0.005 ohm to 0.9 ohm. 3.3 Resistance tolerance. This style resistor is available in resistance tolerances F, H, and J (±1 percent, ±3 percent, and ±5 percent respectively). 3.4 Termination finish. The termination finish shall be identified by a single letter, B for tin/lead (Sn/Pb) (3 percent lead minimum) or T (Sn) for (100 percent tin). 3.5 Power rating. The power rating shall be 1.0 watt at +25°C. The power rating shall be linearly derated to zero at 175°C or 275°C (see 6.5). Beneficial comments, recommendations, additions, deletions, clarifications, etc., and any data which may improve this document should be sent to: Defense Supply Center, Columbus, ATTN: DSCC-VAT, Post Office Box 3990, Columbus, OH 43216-5000, or telephone (614) 692-0553, or facsimile (FAX) (614) 692-6939. AMSC N/A DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. FSC 5905 A-A-55534/1A Inches 0.002 0.020 0.032 0.041 mm 0.05 0.51 0.81 1.04 Inches 0.146 0.449 1.500 mm 3.71 11.41 38.10 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. The picturization of the style above is given as representative of the envelope of the item. Slight deviations from the outline shown, which are contained within the envelope and do not alter the functional aspects of the device, are acceptable. FIGURE 1. Resistors, fixed, wire wound, or metal element (style VLV1). 3.6 Temperature coefficient. The temperature coefficient of resistance shall not exceed ±350 ppm/°C for values 0.01 ohm and above and ±900 ppm for values below 0.01 ohm when derated from -55°C to +175°C or shall not exceed ±350 ppm for all values when derated from -55°C to +275°C. 3.7 Marking. Resistors supplied to this CID shall be marked with the manufacturers standard commercial PIN. Marking of individual small devices (e.g. chips) is not required but is permitted; however, each unit pack supplied to this CID shall be marked with the manufacturer's standard commercial PIN. 4. PRODUCT CONFORMANCE PROVISIONS. Product conformance provisions shall be as specified in A-A-55534. 5. PACKAGING. Packaging shall be as specified in A-A-55534. 6. NOTES 6.1 PIN. The PIN should be used for Government purposes to buy commercial products to this CID. See section 2 for PIN format. 6.2 CAGE code. For ordering purposes, inventory control, and submission of these instruments to DSCC under the Military Parts Control Advisory Group (MPCAG) evaluation program, CAGE code 58536 should be used. 2 A-A-55534/1A 6.3 Source of documents. Commercial Item Description A-A-55534 - Resistor, Fixed, Power type (Very Low Resistance Values), General Requirements For. (Copies of commercial item descriptions are available from the Document Automation and Production Service (DAPS), Building 4D (Customer Service), 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 6.4 Ordering data. Ordering data shall be as specified in A-A-55534. 6.5 Commercial products. As part of the market analysis and research effort, this CID was coordinated with the following MFGR’s of commercial products. At the time of CID preparation and coordination, these MFGR’s were known to have commercial products that would meet the requirements of this CID. (NOTE: This information should not be considered as a list of approved MFGR’s or be used to restrict procurement to only the MFGR’s shown.) Commercial item description (CID) PIN Vendor CAGE AA55534/01-****** Vendor name and address Dale Electronics, Inc. 1122 23rd St. PO Box 609 columbus, NE 68601-0609 Resistance values 0.01 ohm to 0.1 ohm, resistance tolerances F, H, and J, derated to zero at 175°C. 91637 Dale Electronics, Inc. Industrial Park PO Box 87 Dimona 86100, Israel AA55534/01-****** 15915 Resistance values 0.005 ohm to 0.9 ohm, resistance tolerances F, H, and J, derated to zero at 275°C. TEPRO of Florida, Inc. 2608 Enterprise Rd. Clearwater, FL 34623 6.6 Part number (P/N) supersession data. This CID supersedes the MFGR’s style as shown below. This information is being provided to assist in reducing proliferation in the government inventory system. 3 A-A-55534/1A MFGR's CAGE MFGR's style 1/ 91637 LVR-1 15915 TSM1 1/ The MFGR's style shall not be used for procurement to the requirements of this CID. At the time of preparation of this CID, the aforementioned commercial products were reviewed and could be replaced by the CID PIN shown. 6.7 Government users. To acquire information on obtaining these resistors from the Government inventory system, contact Defense Supply Center, Columbus, ATTN: DSCC-CPBC, PO Box 3990, Columbus, OH 43216-5000, or telephone (614) 692-7678. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodian Navy - EC DLA-CC GSA - 7FXE Preparing Activity: DLA-CC Project 5905-1679 4