A-A-59406

[INCH-POUND]
A-A-59406
18 February 2004
COMMERCIAL ITEM DESCRIPTION
INDUCTOR, POWER, SHIELDED, SURFACE MOUNT
The General Services Administration has authorized the use of this
commercial item description (CID) for all federal agencies.
1. SCOPE. This CID covers the general requirements for an inductor. Inductors covered by this CID are
intended for commercial/industrial applications.
2. CLASSIFICATION. This CID uses a classification system which is included in the Part Identification
Number (PIN) as shown in the following example (see 7.1).
AA59406
-
CID
`number
001
Dash number
(see table I)
3. SALIENT CHARACTERISTICS.
3.1 Interface and physical dimensions. Inductors supplied to this CID shall be as specified herein. (see
figure 1).
3.2. Electrical characteristics. The electrical characteristics shall be as specified in table I.
3.3 Weight. The weight shall be no greater than 1.4 grams maximum.
3.4 Operating temperature range. The operating temperature range is -40°C to +85°C.
3.5 Temperature rise. DC current rating for a 15°C rise.
3.6 Altitude. The maximum altitude is 70,000 feet.
3.7 Marking. Inductors supplied to this CID shall be marked with the manufacturer’s standard
commercial PIN.
Beneficial comments recommendations, additions, deletions, clarifications, etc., and any data which may
improve this document should be addressed to: Defense Supply Center, Columbus, ATTN: DSCC-VAT,
Post Office Box 3990, Columbus, OH 43216-5000, or telephone (614) 692-0557, or facsimile (FAX)
(614) 692-6939.
AMSC N/A
DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.
FSC 5950
A-A-59406
Dimension
Inches
A
.370 Max
B
mm
Dimension
Inches
mm
9.40 Max
F
.300
7.62
.510 Max
12.95 Max
G
.100
2.54
C
.330 Dia
8.38 Dia
H
.115
2.92
D
.200 Max
5.08 Max
I
.110
2.79
E
.100
2.54
J
.290
7.37
NOTES:
1. Dimensions are in Inches.
2. Metric equivalents (in parenthesis) are listed for general information only.
FIGURE 1. Configuration and dimensions.
2
A-A-59406
TABLE I. Electrical characteristics.
L ±20%
DCR Max
SRF typ
(µH)
(Ohms)
(MHz)
001
1.0
.025
60
002
1.5
.030
55
003
2.2
.035
55
004
3.3
.040
50
005
4.7
.045
45
006
6.8
.050
40
CID dash
number
AA59406-
007
10
.055
35
008
15
.060
25
009
22
.084
22
010
33
.090
18
011
47
.11
16
012
68
.15
12
013
100
.29
9
014
150
.36
8
015
220
.39
6
016
330
.73
5
017
470
.88
4
018
680
1.15
3
019
1000
1.45
2.5
4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials
to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition
Regulation (FAR).
5. PRODUCT CONFORMANCE PROVISIONS
5.1 Product conformance. The products provided shall meet the salient characteristics of this CID,
conform to the producer’s own drawings, specifications, standards, and quality assurance practices, and
be the same product offered for sale in the commercial market. The Government reserves the right to
require proof of such conformance.
5.2 Market acceptance. The following market acceptance criteria are necessary to document the quality
of the product to be provided under this CID:
a. The company producing the item must have been producing a product meeting the requirements
of this CID for at least 2 years.
b. The company must have sold 1,000 units meeting this CID in the commercial marketplace over
the past 2 years.
6. PACKAGING. Preservation, packing, and marking shall be as specified in the contract or order.
3
A-A-59406
7. NOTES.
7.1 PIN. The PIN should be used for Government purposes to buy commercial products to this CID.
See section 2 for PIN format example.
7.2 Commercial and Government Entity (CAGE) code. For ordering purposes, inventory control, and
submission of these inductors to DSCC under the Military Parts Control Advisory Group (MPCAG)
evaluation program, CAGE code 58536 should be used.
7.3 Ordering data. The contract or order should specify the following:
a. CID document number, revision, and CID PIN.
b. Product conformance provisions.
c. Packaging requirements.
7.4 Commercial products. As part of the market analysis and research effort, this CID was coordinated
with the following manufacturers of commercial products. At the time of CID preparation and
coordination, these manufacturers were known to have commercial products that would meet the
requirements of this CID. (NOTE: This information should not be considered as a list of approved
manufacturers or be used to restrict procurement to only the manufacturers shown.)
MFR's CAGE
02113
MFR's name and address
Coilcraft Inc
1102 Silver Lake Road
Cary, Illinois 60013-1658
Phone number (847) 639-2361
Uniform Resource Locator (URL): www.coilcraft.com
4
A-A-59406
7.5 Part number (P/N) supersession data. This CID supersedes the following manufacturers' P/N's as
shown. This information is being provided to assist in reducing proliferation in the government inventory
system.
TABLE II. P/N supersession data.
CID dash
number
(see table I)
AA59406-
Vendor commercial
PIN
CAGE 02113
1/
001
DT3316P-102
002
DT3316P-152
003
DT3316P-222
004
DT3316P-332
005
DT3316P-472
006
DT3316P-682
007
DT3316P-103
008
DT3316P-153
009
DT3316P-223
010
DT3316P-333
011
DT3316P-473
012
DT3316P-683
013
DT3316P-104
014
DT3316P-154
015
DT3316P-224
016
DT3316P-334
017
DT3316P-474
018
DT3316P-684
019
DT3316P-105
1/ The manufacturer's P/N shall not be used for procurement to the requirements of this CID.
At the time of preparation of this CID, the aforementioned commercial products were
reviewed and could be replaced by the CID P/N shown.
7.6 Government users. To acquire information on obtaining these inductors from the Government
inventory system, contact Defense Supply Center, Columbus, ATTN: DSCC-CPAA, Post Office Box
3990, Columbus, OH 43216-5000, or telephone (614) 692-7741.
MILITARY INTERESTS:
CIVIL AGENCY COORDINATING ACTIVITY:
GSA - 7FXE
Custodians:
Navy - EC
Preparing Activity:
DLA - CC
Project 5950-1152
5